| 2fd42840 | 17-Aug-2018 |
Chris Packham <judge.packham@gmail.com> |
ARM: mach-mvebu: handle fall-back to UART boot
The bootROM in the Armada-38x (and similar) SoC has two modes for UART
boot. The first is when the normal boot media is blank (or otherwise
missing the
ARM: mach-mvebu: handle fall-back to UART boot
The bootROM in the Armada-38x (and similar) SoC has two modes for UART
boot. The first is when the normal boot media is blank (or otherwise
missing the kwb header). The second is when the boot sequence has been
interrupted with the magic byte sequence on the UART lines.
In the first mode the bootROM routine and error code register will
indicate that there was an error booting from the configured media in
bits 7:0. In the second mode there is no error to indicate but the boot
source is provided via bits 31:28.
Handle both situations so that kwboot can be used for both boot
strapping a blank board and for intercepting a regular boot sequence.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: Stefan Roese <sr@denx.de>
show more ...
|
| e0977297 | 17-Aug-2018 |
Chris Packham <judge.packham@gmail.com> |
Revert "arm: mvebu: fix boot from UART when in fallback mode"
This reverts commit e83e2b390038c9075642cb243a6292241beb8d73. This
prevents kwboot from overriding the hardware strapped boot source.
S
Revert "arm: mvebu: fix boot from UART when in fallback mode"
This reverts commit e83e2b390038c9075642cb243a6292241beb8d73. This
prevents kwboot from overriding the hardware strapped boot source.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
show more ...
|
| ca1a4c86 | 18-Jun-2018 |
Baruch Siach <baruch@tkos.co.il> |
mvebu: select boot device at SoC level
Move the gdsys Controlcenter DC specific build time kwbimage.cfg
generation code into the mach-mvebu/ directory to be shared by all 32bit
mvebu platforms.
Rem
mvebu: select boot device at SoC level
Move the gdsys Controlcenter DC specific build time kwbimage.cfg
generation code into the mach-mvebu/ directory to be shared by all 32bit
mvebu platforms.
Remove board specific kwbimage.cfg files, and use the generated one
instead. These files are all identical, with two exceptions. Clearfog
and Helios4 use the sdio boot device, whereas all others use spi. Update
the defconfigs for the exceptional boards to generate the same
kwbimage.cfg as before.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
show more ...
|
| ad105f5f | 18-Jun-2018 |
Baruch Siach <baruch@tkos.co.il> |
mvebu: consolidate SPL boot device config symbols
Use MVEBU_SPL_BOOT_DEVICE_* to select between SPI and MMC, instead of
board specific symbols. This commit enables the boot device selection
menu to
mvebu: consolidate SPL boot device config symbols
Use MVEBU_SPL_BOOT_DEVICE_* to select between SPI and MMC, instead of
board specific symbols. This commit enables the boot device selection
menu to all mvebu platforms, but it is only effective on Turris Omnia
and gdsys Controlcenter DC platforms. A following commit will enable
boot selection for other platforms.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
show more ...
|
| e6fce12d | 09-May-2018 |
Chris Packham <judge.packham@gmail.com> |
ARM: mvebu: a38x: move definition of PEX_CFG_DIRECT_ACCESS
PEX_CFG_DIRECT_ACCESS was defined in ddr3_hws_hw_training_def.h despite
only being used in the serdes code. Move this definition to ctrl_pe
ARM: mvebu: a38x: move definition of PEX_CFG_DIRECT_ACCESS
PEX_CFG_DIRECT_ACCESS was defined in ddr3_hws_hw_training_def.h despite
only being used in the serdes code. Move this definition to ctrl_pex.h
where all the other PEX defines are. Also remove the duplicate
definition of PEX_DEVICE_AND_VENDOR_ID which is already defined in
ctrl_pex.h.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
show more ...
|