1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * (C) Copyright 2009 4 * Net Insight <www.netinsight.net> 5 * Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net> 6 * 7 * Based on sheevaplug.h: 8 * (C) Copyright 2009 9 * Marvell Semiconductor <www.marvell.com> 10 * Written-by: Prafulla Wadaskar <prafulla@marvell.com> 11 */ 12 13 #ifndef _CONFIG_OPENRD_H 14 #define _CONFIG_OPENRD_H 15 16 /* 17 * High Level Configuration Options (easy to change) 18 */ 19 #define CONFIG_SHEEVA_88SV131 1 /* CPU Core subversion */ 20 #define CONFIG_KW88F6281 1 /* SOC Name */ 21 #define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ 22 23 /* 24 * Commands configuration 25 */ 26 #define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ 27 #define CONFIG_MTD_PARTITIONS 28 29 /* 30 * mv-common.h should be defined after CMD configs since it used them 31 * to enable certain macros 32 */ 33 #include "mv-common.h" 34 35 /* 36 * Environment variables configurations 37 */ 38 #ifdef CONFIG_CMD_NAND 39 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K */ 40 #endif 41 /* 42 * max 4k env size is enough, but in case of nand 43 * it has to be rounded to sector size 44 */ 45 #define CONFIG_ENV_SIZE 0x20000 /* 128k */ 46 #define CONFIG_ENV_ADDR 0x60000 47 #define CONFIG_ENV_OFFSET 0x60000 /* env starts here */ 48 /* 49 * Environment is right behind U-Boot in flash. Make sure U-Boot 50 * doesn't grow into the environment area. 51 */ 52 #define CONFIG_BOARD_SIZE_LIMIT CONFIG_ENV_OFFSET 53 54 /* 55 * Default environment variables 56 */ 57 #define CONFIG_BOOTCOMMAND "${x_bootcmd_kernel}; " \ 58 "setenv bootargs ${x_bootargs} ${x_bootargs_root}; " \ 59 "${x_bootcmd_usb}; bootm 0x6400000;" 60 61 #define CONFIG_EXTRA_ENV_SETTINGS "x_bootargs=console=ttyS0,115200 " \ 62 CONFIG_MTDPARTS_DEFAULT " rw ubi.mtd=2,2048\0" \ 63 "x_bootcmd_kernel=nand read 0x6400000 0x100000 0x300000\0" \ 64 "x_bootcmd_usb=usb start\0" \ 65 "x_bootargs_root=root=ubi0:rootfs rootfstype=ubifs\0" \ 66 "mtdids="CONFIG_MTDIDS_DEFAULT"\0" \ 67 "mtdparts="CONFIG_MTDPARTS_DEFAULT"\0" 68 69 /* 70 * Ethernet Driver configuration 71 */ 72 #ifdef CONFIG_CMD_NET 73 # ifdef CONFIG_BOARD_IS_OPENRD_BASE 74 # define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */ 75 # else 76 # define CONFIG_MVGBE_PORTS {1, 1} /* enable both ports */ 77 # endif 78 # ifdef CONFIG_BOARD_IS_OPENRD_ULTIMATE 79 # define CONFIG_PHY_BASE_ADR 0x0 80 # define PHY_NO "88E1121" 81 # else 82 # define CONFIG_PHY_BASE_ADR 0x8 83 # define PHY_NO "88E1116" 84 # endif 85 #endif /* CONFIG_CMD_NET */ 86 87 /* 88 * SATA Driver configuration 89 */ 90 #ifdef CONFIG_MVSATA_IDE 91 #define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET 92 #define CONFIG_SYS_ATA_IDE1_OFFSET MV_SATA_PORT1_OFFSET 93 #endif /*CONFIG_MVSATA_IDE*/ 94 95 #ifdef CONFIG_CMD_MMC 96 #define CONFIG_MVEBU_MMC 97 #define CONFIG_SYS_MMC_BASE KW_SDIO_BASE 98 #endif /* CONFIG_CMD_MMC */ 99 100 #endif /* _CONFIG_OPENRD_BASE_H */ 101