1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * Copyright (C) 2009-2010 Freescale Semiconductor, Inc. 4 * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok@emcraft.com 5 * 6 */ 7 8 #ifndef __CONFIG_H 9 #define __CONFIG_H 10 11 /* 12 * High Level Configuration Options 13 */ 14 #define CONFIG_E300 1 /* E300 family */ 15 #define CONFIG_MPC830x 1 /* MPC830x family */ 16 #define CONFIG_MPC8308 1 /* MPC8308 CPU specific */ 17 18 /* 19 * On-board devices 20 * 21 * TSECs 22 */ 23 #define CONFIG_TSEC1 24 #define CONFIG_TSEC2 25 26 /* 27 * System Clock Setup 28 */ 29 #define CONFIG_83XX_CLKIN 33333333 /* in Hz */ 30 #define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN 31 32 /* 33 * Hardware Reset Configuration Word 34 * if CLKIN is 66.66MHz, then 35 * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz 36 * We choose the A type silicon as default, so the core is 400Mhz. 37 */ 38 #define CONFIG_SYS_HRCW_LOW (\ 39 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ 40 HRCWL_DDR_TO_SCB_CLK_2X1 |\ 41 HRCWL_SVCOD_DIV_2 |\ 42 HRCWL_CSB_TO_CLKIN_4X1 |\ 43 HRCWL_CORE_TO_CSB_3X1) 44 /* 45 * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits 46 * in 8308's HRCWH according to the manual, but original Freescale's 47 * code has them and I've expirienced some problems using the board 48 * with BDI3000 attached when I've tried to set these bits to zero 49 * (UART doesn't work after the 'reset run' command). 50 */ 51 #define CONFIG_SYS_HRCW_HIGH (\ 52 HRCWH_PCI_HOST |\ 53 HRCWH_PCI1_ARBITER_ENABLE |\ 54 HRCWH_CORE_ENABLE |\ 55 HRCWH_FROM_0X00000100 |\ 56 HRCWH_BOOTSEQ_DISABLE |\ 57 HRCWH_SW_WATCHDOG_DISABLE |\ 58 HRCWH_ROM_LOC_LOCAL_16BIT |\ 59 HRCWH_RL_EXT_LEGACY |\ 60 HRCWH_TSEC1M_IN_MII |\ 61 HRCWH_TSEC2M_IN_MII |\ 62 HRCWH_BIG_ENDIAN) 63 64 /* 65 * System IO Config 66 */ 67 #define CONFIG_SYS_SICRH (\ 68 SICRH_ESDHC_A_GPIO |\ 69 SICRH_ESDHC_B_GPIO |\ 70 SICRH_ESDHC_C_GTM |\ 71 SICRH_GPIO_A_TSEC2 |\ 72 SICRH_GPIO_B_TSEC2_TX_CLK |\ 73 SICRH_IEEE1588_A_GPIO |\ 74 SICRH_USB |\ 75 SICRH_GTM_GPIO |\ 76 SICRH_IEEE1588_B_GPIO |\ 77 SICRH_ETSEC2_CRS |\ 78 SICRH_GPIOSEL_1 |\ 79 SICRH_TMROBI_V3P3 |\ 80 SICRH_TSOBI1_V3P3 |\ 81 SICRH_TSOBI2_V3P3) /* 0xf577d100 */ 82 #define CONFIG_SYS_SICRL (\ 83 SICRL_SPI_PF0 |\ 84 SICRL_UART_PF0 |\ 85 SICRL_IRQ_PF0 |\ 86 SICRL_I2C2_PF0 |\ 87 SICRL_ETSEC1_TX_CLK) /* 0x00000000 */ 88 89 #define CONFIG_SYS_GPIO1_PRELIM 90 /* GPIO Default input/output settings */ 91 #define CONFIG_SYS_GPIO1_DIR 0x7AAF8C00 92 /* 93 * Default GPIO values: 94 * LED#1 enabled; WLAN enabled; Both COM LED on (orange) 95 */ 96 #define CONFIG_SYS_GPIO1_DAT 0x08008C00 97 98 /* 99 * IMMR new address 100 */ 101 #define CONFIG_SYS_IMMR 0xE0000000 102 103 /* 104 * SERDES 105 */ 106 #define CONFIG_FSL_SERDES 107 #define CONFIG_FSL_SERDES1 0xe3000 108 109 /* 110 * Arbiter Setup 111 */ 112 #define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */ 113 #define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count is 4 */ 114 #define CONFIG_SYS_SPCR_TSECEP 3 /* eTSEC emergency priority is highest */ 115 116 /* 117 * DDR Setup 118 */ 119 #define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ 120 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE 121 #define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE 122 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 123 #define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \ 124 | DDRCDR_PZ_LOZ \ 125 | DDRCDR_NZ_LOZ \ 126 | DDRCDR_ODT \ 127 | DDRCDR_Q_DRN) 128 /* 0x7b880001 */ 129 /* 130 * Manually set up DDR parameters 131 * consist of two chips HY5PS12621BFP-C4 from HYNIX 132 */ 133 134 #define CONFIG_SYS_DDR_SIZE 128 /* MB */ 135 136 #define CONFIG_SYS_DDR_CS0_BNDS 0x00000007 137 #define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \ 138 | CSCONFIG_ODT_RD_NEVER \ 139 | CSCONFIG_ODT_WR_ONLY_CURRENT \ 140 | CSCONFIG_ROW_BIT_13 \ 141 | CSCONFIG_COL_BIT_10) 142 /* 0x80010102 */ 143 #define CONFIG_SYS_DDR_TIMING_3 0x00000000 144 #define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \ 145 | (0 << TIMING_CFG0_WRT_SHIFT) \ 146 | (0 << TIMING_CFG0_RRT_SHIFT) \ 147 | (0 << TIMING_CFG0_WWT_SHIFT) \ 148 | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \ 149 | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \ 150 | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \ 151 | (2 << TIMING_CFG0_MRS_CYC_SHIFT)) 152 /* 0x00220802 */ 153 #define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \ 154 | (7 << TIMING_CFG1_ACTTOPRE_SHIFT) \ 155 | (2 << TIMING_CFG1_ACTTORW_SHIFT) \ 156 | (5 << TIMING_CFG1_CASLAT_SHIFT) \ 157 | (6 << TIMING_CFG1_REFREC_SHIFT) \ 158 | (2 << TIMING_CFG1_WRREC_SHIFT) \ 159 | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \ 160 | (2 << TIMING_CFG1_WRTORD_SHIFT)) 161 /* 0x27256222 */ 162 #define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \ 163 | (4 << TIMING_CFG2_CPO_SHIFT) \ 164 | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \ 165 | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \ 166 | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \ 167 | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \ 168 | (5 << TIMING_CFG2_FOUR_ACT_SHIFT)) 169 /* 0x121048c5 */ 170 #define CONFIG_SYS_DDR_INTERVAL ((0x0360 << SDRAM_INTERVAL_REFINT_SHIFT) \ 171 | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) 172 /* 0x03600100 */ 173 #define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \ 174 | SDRAM_CFG_SDRAM_TYPE_DDR2 \ 175 | SDRAM_CFG_DBW_32) 176 /* 0x43080000 */ 177 178 #define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */ 179 #define CONFIG_SYS_DDR_MODE ((0x0448 << SDRAM_MODE_ESD_SHIFT) \ 180 | (0x0232 << SDRAM_MODE_SD_SHIFT)) 181 /* ODT 150ohm CL=3, AL=1 on SDRAM */ 182 #define CONFIG_SYS_DDR_MODE2 0x00000000 183 184 /* 185 * Memory test 186 */ 187 #define CONFIG_SYS_MEMTEST_START 0x00001000 /* memtest region */ 188 #define CONFIG_SYS_MEMTEST_END 0x07f00000 189 190 /* 191 * The reserved memory 192 */ 193 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 194 195 #define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */ 196 #define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ 197 198 /* 199 * Initial RAM Base Address Setup 200 */ 201 #define CONFIG_SYS_INIT_RAM_LOCK 1 202 #define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ 203 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */ 204 #define CONFIG_SYS_GBL_DATA_OFFSET \ 205 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 206 207 /* 208 * Local Bus Configuration & Clock Setup 209 */ 210 #define CONFIG_SYS_LCRR_DBYP LCRR_DBYP 211 #define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2 212 #define CONFIG_SYS_LBC_LBCR 0x00040000 213 214 /* 215 * FLASH on the Local Bus 216 */ 217 #define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ 218 #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ 219 #define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT 220 221 #define CONFIG_SYS_FLASH_BASE 0xFC000000 /* FLASH base address */ 222 #define CONFIG_SYS_FLASH_SIZE 64 /* FLASH size is 64M */ 223 #define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */ 224 225 /* Window base at flash base */ 226 #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE 227 #define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_64MB) 228 229 #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \ 230 | BR_PS_16 /* 16 bit port */ \ 231 | BR_MS_GPCM /* MSEL = GPCM */ \ 232 | BR_V) /* valid */ 233 #define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \ 234 | OR_UPM_XAM \ 235 | OR_GPCM_CSNT \ 236 | OR_GPCM_ACS_DIV2 \ 237 | OR_GPCM_XACS \ 238 | OR_GPCM_SCY_4 \ 239 | OR_GPCM_TRLX_SET \ 240 | OR_GPCM_EHTR_SET) 241 242 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 243 #define CONFIG_SYS_MAX_FLASH_SECT 512 244 245 /* Flash Erase Timeout (ms) */ 246 #define CONFIG_SYS_FLASH_ERASE_TOUT (1000 * 1024) 247 /* Flash Write Timeout (ms) */ 248 #define CONFIG_SYS_FLASH_WRITE_TOUT (500 * 1024) 249 250 /* 251 * SJA1000 CAN controller on Local Bus 252 */ 253 #define CONFIG_SYS_SJA1000_BASE 0xFBFF0000 254 #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_SJA1000_BASE \ 255 | BR_PS_8 /* 8 bit port size */ \ 256 | BR_MS_GPCM /* MSEL = GPCM */ \ 257 | BR_V) /* valid */ 258 #define CONFIG_SYS_OR1_PRELIM (OR_AM_32KB \ 259 | OR_GPCM_SCY_5 \ 260 | OR_GPCM_EHTR_SET) 261 /* 0xFFFF8052 */ 262 263 #define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_SJA1000_BASE 264 #define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_32KB) 265 266 /* 267 * CPLD on Local Bus 268 */ 269 #define CONFIG_SYS_CPLD_BASE 0xFBFF8000 270 #define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_CPLD_BASE \ 271 | BR_PS_8 /* 8 bit port */ \ 272 | BR_MS_GPCM /* MSEL = GPCM */ \ 273 | BR_V) /* valid */ 274 #define CONFIG_SYS_OR2_PRELIM (OR_AM_32KB \ 275 | OR_GPCM_SCY_4 \ 276 | OR_GPCM_EHTR_SET) 277 /* 0xFFFF8042 */ 278 279 #define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_CPLD_BASE 280 #define CONFIG_SYS_LBLAWAR2_PRELIM (LBLAWAR_EN | LBLAWAR_32KB) 281 282 /* 283 * Serial Port 284 */ 285 #undef CONFIG_SERIAL_SOFTWARE_FIFO 286 #define CONFIG_SYS_NS16550_SERIAL 287 #define CONFIG_SYS_NS16550_REG_SIZE 1 288 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 289 290 #define CONFIG_SYS_BAUDRATE_TABLE \ 291 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 292 293 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500) 294 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600) 295 296 /* I2C */ 297 #define CONFIG_SYS_I2C 298 #define CONFIG_SYS_I2C_FSL 299 #define CONFIG_SYS_FSL_I2C_SPEED 400000 300 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 301 #define CONFIG_SYS_FSL_I2C2_SPEED 400000 302 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 303 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 304 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 305 306 /* 307 * General PCI 308 * Addresses are mapped 1-1. 309 */ 310 #define CONFIG_SYS_PCIE1_BASE 0xA0000000 311 #define CONFIG_SYS_PCIE1_MEM_BASE 0xA0000000 312 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xA0000000 313 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 314 #define CONFIG_SYS_PCIE1_CFG_BASE 0xB0000000 315 #define CONFIG_SYS_PCIE1_CFG_SIZE 0x01000000 316 #define CONFIG_SYS_PCIE1_IO_BASE 0x00000000 317 #define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000 318 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 319 320 /* enable PCIE clock */ 321 #define CONFIG_SYS_SCCR_PCIEXP1CM 1 322 323 #define CONFIG_PCI_INDIRECT_BRIDGE 324 #define CONFIG_PCIE 325 326 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ 327 #define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1 328 329 /* 330 * TSEC 331 */ 332 #define CONFIG_SYS_TSEC1_OFFSET 0x24000 333 #define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET) 334 #define CONFIG_SYS_TSEC2_OFFSET 0x25000 335 #define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET) 336 337 /* 338 * TSEC ethernet configuration 339 */ 340 #define CONFIG_TSEC1_NAME "eTSEC0" 341 #define CONFIG_TSEC2_NAME "eTSEC1" 342 #define TSEC1_PHY_ADDR 1 343 #define TSEC2_PHY_ADDR 2 344 #define TSEC1_PHYIDX 0 345 #define TSEC2_PHYIDX 0 346 #define TSEC1_FLAGS 0 347 #define TSEC2_FLAGS 0 348 349 /* Options are: eTSEC[0-1] */ 350 #define CONFIG_ETHPRIME "eTSEC0" 351 352 /* 353 * Environment 354 */ 355 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \ 356 CONFIG_SYS_MONITOR_LEN) 357 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ 358 #define CONFIG_ENV_SIZE 0x2000 359 #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) 360 #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE 361 362 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 363 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 364 365 /* 366 * BOOTP options 367 */ 368 #define CONFIG_BOOTP_BOOTFILESIZE 369 370 /* 371 * Command line configuration. 372 */ 373 374 /* 375 * Miscellaneous configurable options 376 */ 377 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 378 379 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 380 381 /* Boot Argument Buffer Size */ 382 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 383 384 /* 385 * For booting Linux, the board info and command line data 386 * have to be in the first 8 MB of memory, since this is 387 * the maximum mapped by the Linux kernel during initialization. 388 */ 389 #define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */ 390 391 /* 392 * Core HID Setup 393 */ 394 #define CONFIG_SYS_HID0_INIT 0x000000000 395 #define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ 396 HID0_ENABLE_INSTRUCTION_CACHE | \ 397 HID0_ENABLE_DYNAMIC_POWER_MANAGMENT) 398 #define CONFIG_SYS_HID2 HID2_HBE 399 400 /* 401 * MMU Setup 402 */ 403 404 /* DDR: cache cacheable */ 405 #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \ 406 BATL_MEMCOHERENCE) 407 #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \ 408 BATU_VS | BATU_VP) 409 #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L 410 #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U 411 412 /* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */ 413 #define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR | BATL_PP_RW | \ 414 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 415 #define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \ 416 BATU_VP) 417 #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L 418 #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U 419 420 /* FLASH: icache cacheable, but dcache-inhibit and guarded */ 421 #define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \ 422 BATL_MEMCOHERENCE) 423 #define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \ 424 BATU_VS | BATU_VP) 425 #define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \ 426 BATL_CACHEINHIBIT | \ 427 BATL_GUARDEDSTORAGE) 428 #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U 429 430 /* Stack in dcache: cacheable, no memory coherence */ 431 #define CONFIG_SYS_IBAT3L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW) 432 #define CONFIG_SYS_IBAT3U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \ 433 BATU_VS | BATU_VP) 434 #define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L 435 #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U 436 437 /* 438 * Environment Configuration 439 */ 440 441 #define CONFIG_ENV_OVERWRITE 442 443 #if defined(CONFIG_TSEC_ENET) 444 #define CONFIG_HAS_ETH0 445 #define CONFIG_HAS_ETH1 446 #endif 447 448 #define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */ 449 450 451 #define CONFIG_EXTRA_ENV_SETTINGS \ 452 "netdev=eth0\0" \ 453 "consoledev=ttyS0\0" \ 454 "nfsargs=setenv bootargs root=/dev/nfs rw " \ 455 "nfsroot=${serverip}:${rootpath}\0" \ 456 "ramargs=setenv bootargs root=/dev/ram rw\0" \ 457 "addip=setenv bootargs ${bootargs} " \ 458 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ 459 ":${hostname}:${netdev}:off panic=1\0" \ 460 "addtty=setenv bootargs ${bootargs}" \ 461 " console=${consoledev},${baudrate}\0" \ 462 "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \ 463 "addmisc=setenv bootargs ${bootargs}\0" \ 464 "kernel_addr=FC0A0000\0" \ 465 "fdt_addr=FC2A0000\0" \ 466 "ramdisk_addr=FC2C0000\0" \ 467 "u-boot=mpc8308_p1m/u-boot.bin\0" \ 468 "kernel_addr_r=1000000\0" \ 469 "fdt_addr_r=C00000\0" \ 470 "hostname=mpc8308_p1m\0" \ 471 "bootfile=mpc8308_p1m/uImage\0" \ 472 "fdtfile=mpc8308_p1m/mpc8308_p1m.dtb\0" \ 473 "rootpath=/opt/eldk-4.2/ppc_6xx\0" \ 474 "flash_self=run ramargs addip addtty addmtd addmisc;" \ 475 "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ 476 "flash_nfs=run nfsargs addip addtty addmtd addmisc;" \ 477 "bootm ${kernel_addr} - ${fdt_addr}\0" \ 478 "net_nfs=tftp ${kernel_addr_r} ${bootfile};" \ 479 "tftp ${fdt_addr_r} ${fdtfile};" \ 480 "run nfsargs addip addtty addmtd addmisc;" \ 481 "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ 482 "bootcmd=run flash_self\0" \ 483 "load=tftp ${loadaddr} ${u-boot}\0" \ 484 "update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE) \ 485 " +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\ 486 " +${filesize};cp.b ${fileaddr} " \ 487 __stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \ 488 "upd=run load update\0" \ 489 490 #endif /* __CONFIG_H */ 491