1menu "Command line interface" 2 3config CMDLINE 4 bool "Support U-Boot commands" 5 default y 6 help 7 Enable U-Boot's command-line functions. This provides a means 8 to enter commands into U-Boot for a wide variety of purposes. It 9 also allows scripts (containing commands) to be executed. 10 Various commands and command categorys can be indivdually enabled. 11 Depending on the number of commands enabled, this can add 12 substantially to the size of U-Boot. 13 14config HUSH_PARSER 15 bool "Use hush shell" 16 depends on CMDLINE 17 help 18 This option enables the "hush" shell (from Busybox) as command line 19 interpreter, thus enabling powerful command line syntax like 20 if...then...else...fi conditionals or `&&' and '||' 21 constructs ("shell scripts"). 22 23 If disabled, you get the old, much simpler behaviour with a somewhat 24 smaller memory footprint. 25 26config CMDLINE_EDITING 27 bool "Enable command line editing" 28 depends on CMDLINE 29 default y 30 help 31 Enable editing and History functions for interactive command line 32 input operations 33 34config AUTO_COMPLETE 35 bool "Enable auto complete using TAB" 36 depends on CMDLINE 37 default y 38 help 39 Enable auto completion of commands using TAB. 40 41config SYS_LONGHELP 42 bool "Enable long help messages" 43 depends on CMDLINE 44 default y if CMDLINE 45 help 46 Defined when you want long help messages included 47 Do not set this option when short of memory. 48 49config SYS_PROMPT 50 string "Shell prompt" 51 default "=> " 52 help 53 This string is displayed in the command line to the left of the 54 cursor. 55 56menu "Autoboot options" 57 58config AUTOBOOT 59 bool "Autoboot" 60 default y 61 help 62 This enables the autoboot. See doc/README.autoboot for detail. 63 64config AUTOBOOT_KEYED 65 bool "Stop autobooting via specific input key / string" 66 default n 67 help 68 This option enables stopping (aborting) of the automatic 69 boot feature only by issuing a specific input key or 70 string. If not enabled, any input key will abort the 71 U-Boot automatic booting process and bring the device 72 to the U-Boot prompt for user input. 73 74config AUTOBOOT_PROMPT 75 string "Autoboot stop prompt" 76 depends on AUTOBOOT_KEYED 77 default "Autoboot in %d seconds\\n" 78 help 79 This string is displayed before the boot delay selected by 80 CONFIG_BOOTDELAY starts. If it is not defined there is no 81 output indicating that autoboot is in progress. 82 83 Note that this define is used as the (only) argument to a 84 printf() call, so it may contain '%' format specifications, 85 provided that it also includes, sepearated by commas exactly 86 like in a printf statement, the required arguments. It is 87 the responsibility of the user to select only such arguments 88 that are valid in the given context. 89 90config AUTOBOOT_ENCRYPTION 91 bool "Enable encryption in autoboot stopping" 92 depends on AUTOBOOT_KEYED 93 default n 94 95config AUTOBOOT_DELAY_STR 96 string "Delay autobooting via specific input key / string" 97 depends on AUTOBOOT_KEYED && !AUTOBOOT_ENCRYPTION 98 help 99 This option delays the automatic boot feature by issuing 100 a specific input key or string. If CONFIG_AUTOBOOT_DELAY_STR 101 or the environment variable "bootdelaykey" is specified 102 and this string is received from console input before 103 autoboot starts booting, U-Boot gives a command prompt. The 104 U-Boot prompt will time out if CONFIG_BOOT_RETRY_TIME is 105 used, otherwise it never times out. 106 107config AUTOBOOT_STOP_STR 108 string "Stop autobooting via specific input key / string" 109 depends on AUTOBOOT_KEYED && !AUTOBOOT_ENCRYPTION 110 help 111 This option enables stopping (aborting) of the automatic 112 boot feature only by issuing a specific input key or 113 string. If CONFIG_AUTOBOOT_STOP_STR or the environment 114 variable "bootstopkey" is specified and this string is 115 received from console input before autoboot starts booting, 116 U-Boot gives a command prompt. The U-Boot prompt never 117 times out, even if CONFIG_BOOT_RETRY_TIME is used. 118 119config AUTOBOOT_KEYED_CTRLC 120 bool "Enable Ctrl-C autoboot interruption" 121 depends on AUTOBOOT_KEYED && !AUTOBOOT_ENCRYPTION 122 default n 123 help 124 This option allows for the boot sequence to be interrupted 125 by ctrl-c, in addition to the "bootdelaykey" and "bootstopkey". 126 Setting this variable provides an escape sequence from the 127 limited "password" strings. 128 129config AUTOBOOT_STOP_STR_SHA256 130 string "Stop autobooting via SHA256 encrypted password" 131 depends on AUTOBOOT_KEYED && AUTOBOOT_ENCRYPTION 132 help 133 This option adds the feature to only stop the autobooting, 134 and therefore boot into the U-Boot prompt, when the input 135 string / password matches a values that is encypted via 136 a SHA256 hash and saved in the environment. 137 138endmenu 139 140config BUILD_BIN2C 141 bool 142 143comment "Commands" 144 145menu "Info commands" 146 147config CMD_BDI 148 bool "bdinfo" 149 default y 150 help 151 Print board info 152 153config CMD_CONFIG 154 bool "config" 155 default SANDBOX 156 select BUILD_BIN2C 157 help 158 Print ".config" contents. 159 160 If this option is enabled, the ".config" file contents are embedded 161 in the U-Boot image and can be printed on the console by the "config" 162 command. This provides information of which options are enabled on 163 the running U-Boot. 164 165config CMD_CONSOLE 166 bool "coninfo" 167 default y 168 help 169 Print console devices and information. 170 171config CMD_CPU 172 bool "cpu" 173 help 174 Print information about available CPUs. This normally shows the 175 number of CPUs, type (e.g. manufacturer, architecture, product or 176 internal name) and clock frequency. Other information may be 177 available depending on the CPU driver. 178 179config CMD_LICENSE 180 bool "license" 181 select BUILD_BIN2C 182 help 183 Print GPL license text 184 185config CMD_REGINFO 186 bool "reginfo" 187 depends on PPC 188 help 189 Register dump 190 191endmenu 192 193menu "Boot commands" 194 195config CMD_BOOTD 196 bool "bootd" 197 default y 198 help 199 Run the command stored in the environment "bootcmd", i.e. 200 "bootd" does the same thing as "run bootcmd". 201 202config CMD_BOOTM 203 bool "bootm" 204 default y 205 help 206 Boot an application image from the memory. 207 208config CMD_BOOTZ 209 bool "bootz" 210 help 211 Boot the Linux zImage 212 213config CMD_BOOTI 214 bool "booti" 215 depends on ARM64 216 default y 217 help 218 Boot an AArch64 Linux Kernel image from memory. 219 220config CMD_BOOTEFI 221 bool "bootefi" 222 depends on EFI_LOADER 223 default y 224 help 225 Boot an EFI image from memory. 226 227config CMD_BOOTEFI_HELLO_COMPILE 228 bool "Compile a standard EFI hello world binary for testing" 229 depends on CMD_BOOTEFI && (ARM || X86 || RISCV) 230 default y 231 help 232 This compiles a standard EFI hello world application with U-Boot so 233 that it can be used with the test/py testing framework. This is useful 234 for testing that EFI is working at a basic level, and for bringing 235 up EFI support on a new architecture. 236 237 No additional space will be required in the resulting U-Boot binary 238 when this option is enabled. 239 240config CMD_BOOTEFI_HELLO 241 bool "Allow booting a standard EFI hello world for testing" 242 depends on CMD_BOOTEFI_HELLO_COMPILE 243 help 244 This adds a standard EFI hello world application to U-Boot so that 245 it can be used with the 'bootefi hello' command. This is useful 246 for testing that EFI is working at a basic level, and for bringing 247 up EFI support on a new architecture. 248 249source lib/efi_selftest/Kconfig 250 251config CMD_BOOTMENU 252 bool "bootmenu" 253 select MENU 254 help 255 Add an ANSI terminal boot menu command. 256 257config CMD_ELF 258 bool "bootelf, bootvx" 259 default y 260 help 261 Boot an ELF/vxWorks image from the memory. 262 263config CMD_FDT 264 bool "Flattened Device Tree utility commands" 265 default y 266 depends on OF_LIBFDT 267 help 268 Do FDT related setup before booting into the Operating System. 269 270config CMD_GO 271 bool "go" 272 default y 273 help 274 Start an application at a given address. 275 276config CMD_RUN 277 bool "run" 278 default y 279 help 280 Run the command in the given environment variable. 281 282config CMD_IMI 283 bool "iminfo" 284 default y 285 help 286 Print header information for application image. 287 288config CMD_IMLS 289 bool "imls" 290 help 291 List all images found in flash 292 293config CMD_XIMG 294 bool "imxtract" 295 default y 296 help 297 Extract a part of a multi-image. 298 299config CMD_POWEROFF 300 bool "poweroff" 301 help 302 Poweroff/Shutdown the system 303 304config CMD_SPL 305 bool "spl export - Export boot information for Falcon boot" 306 depends on SPL 307 help 308 Falcon mode allows booting directly from SPL into an Operating 309 System such as Linux, thus skipping U-Boot proper. See 310 doc/README.falcon for full information about how to use this 311 command. 312 313config CMD_SPL_NAND_OFS 314 hex "Offset of OS command line args for Falcon-mode NAND boot" 315 depends on CMD_SPL 316 default 0 317 help 318 This provides the offset of the command line arguments for Linux 319 when booting from NAND in Falcon mode. See doc/README.falcon 320 for full information about how to use this option (and also see 321 board/gateworks/gw_ventana/README for an example). 322 323config CMD_SPL_WRITE_SIZE 324 hex "Size of argument area" 325 depends on CMD_SPL 326 default 0x2000 327 help 328 This provides the size of the command-line argument area in NAND 329 flash used by Falcon-mode boot. See the documentation until CMD_SPL 330 for detail. 331 332config CMD_FITUPD 333 bool "fitImage update command" 334 help 335 Implements the 'fitupd' command, which allows to automatically 336 store software updates present on a TFTP server in NOR Flash 337 338config CMD_THOR_DOWNLOAD 339 bool "thor - TIZEN 'thor' download" 340 help 341 Implements the 'thor' download protocol. This is a way of 342 downloading a software update over USB from an attached host. 343 There is no documentation about this within the U-Boot source code 344 but you should be able to find something on the interwebs. 345 346config CMD_ZBOOT 347 bool "zboot - x86 boot command" 348 help 349 With x86 machines it is common to boot a bzImage file which 350 contains both a kernel and a setup.bin file. The latter includes 351 configuration information from the dark ages which x86 boards still 352 need to pick things out of. 353 354 Consider using FIT in preference to this since it supports directly 355 booting both 32- and 64-bit kernels, as well as secure boot. 356 Documentation is available in doc/uImage.FIT/x86-fit-boot.txt 357 358endmenu 359 360menu "Environment commands" 361 362config CMD_ASKENV 363 bool "ask for env variable" 364 help 365 Ask for environment variable 366 367config CMD_EXPORTENV 368 bool "env export" 369 default y 370 help 371 Export environments. 372 373config CMD_IMPORTENV 374 bool "env import" 375 default y 376 help 377 Import environments. 378 379config CMD_EDITENV 380 bool "editenv" 381 default y 382 help 383 Edit environment variable. 384 385config CMD_GREPENV 386 bool "search env" 387 help 388 Allow for searching environment variables 389 390config CMD_SAVEENV 391 bool "saveenv" 392 default y 393 help 394 Save all environment variables into the compiled-in persistent 395 storage. 396 397config CMD_ENV_EXISTS 398 bool "env exists" 399 default y 400 help 401 Check if a variable is defined in the environment for use in 402 shell scripting. 403 404config CMD_ENV_CALLBACK 405 bool "env callbacks - print callbacks and their associated variables" 406 help 407 Some environment variable have callbacks defined by 408 U_BOOT_ENV_CALLBACK. These are called when the variable changes. 409 For example changing "baudrate" adjust the serial baud rate. This 410 command lists the currently defined callbacks. 411 412config CMD_ENV_FLAGS 413 bool "env flags -print variables that have non-default flags" 414 help 415 Some environment variables have special flags that control their 416 behaviour. For example, serial# can only be written once and cannot 417 be deleted. This command shows the variables that have special 418 flags. 419 420endmenu 421 422menu "Memory commands" 423 424config CMD_BINOP 425 bool "binop" 426 help 427 Compute binary operations (xor, or, and) of byte arrays of arbitrary 428 size from memory and store the result in memory or the environment. 429 430config CMD_CRC32 431 bool "crc32" 432 default y 433 select HASH 434 help 435 Compute CRC32. 436 437config CRC32_VERIFY 438 bool "crc32 -v" 439 depends on CMD_CRC32 440 help 441 Add -v option to verify data against a crc32 checksum. 442 443config CMD_EEPROM 444 bool "eeprom - EEPROM subsystem" 445 help 446 (deprecated, needs conversion to driver model) 447 Provides commands to read and write EEPROM (Electrically Erasable 448 Programmable Read Only Memory) chips that are connected over an 449 I2C bus. 450 451config CMD_EEPROM_LAYOUT 452 bool "Enable layout-aware eeprom commands" 453 depends on CMD_EEPROM 454 help 455 (deprecated, needs conversion to driver model) 456 When enabled, additional eeprom sub-commands become available. 457 458 eeprom print - prints the contents of the eeprom in a human-readable 459 way (eeprom layout fields, and data formatted to be fit for human 460 consumption). 461 462 eeprom update - allows user to update eeprom fields by specifying 463 the field name, and providing the new data in a human readable format 464 (same format as displayed by the eeprom print command). 465 466 Both commands can either auto detect the layout, or be told which 467 layout to use. 468 469 Feature API: 470 __weak int parse_layout_version(char *str) 471 - override to provide your own layout name parsing 472 __weak void __eeprom_layout_assign(struct eeprom_layout *layout, 473 int layout_version); 474 - override to setup the layout metadata based on the version 475 __weak int eeprom_layout_detect(unsigned char *data) 476 - override to provide your own algorithm for detecting layout 477 version 478 eeprom_field.c 479 - contains various printing and updating functions for common 480 types of eeprom fields. Can be used for defining 481 custom layouts. 482 483config EEPROM_LAYOUT_HELP_STRING 484 string "Tells user what layout names are supported" 485 depends on CMD_EEPROM_LAYOUT 486 default "<not defined>" 487 help 488 Help printed with the LAYOUT VERSIONS part of the 'eeprom' 489 command's help. 490 491config LOOPW 492 bool "loopw" 493 help 494 Infinite write loop on address range 495 496config CMD_MD5SUM 497 bool "md5sum" 498 default n 499 select MD5 500 help 501 Compute MD5 checksum. 502 503config MD5SUM_VERIFY 504 bool "md5sum -v" 505 default n 506 depends on CMD_MD5SUM 507 help 508 Add -v option to verify data against an MD5 checksum. 509 510config CMD_MEMINFO 511 bool "meminfo" 512 help 513 Display memory information. 514 515config CMD_MEMORY 516 bool "md, mm, nm, mw, cp, cmp, base, loop" 517 default y 518 help 519 Memory commands. 520 md - memory display 521 mm - memory modify (auto-incrementing address) 522 nm - memory modify (constant address) 523 mw - memory write (fill) 524 cp - memory copy 525 cmp - memory compare 526 base - print or set address offset 527 loop - initialize loop on address range 528 529config CMD_MEMTEST 530 bool "memtest" 531 help 532 Simple RAM read/write test. 533 534if CMD_MEMTEST 535 536config SYS_ALT_MEMTEST 537 bool "Alternative test" 538 help 539 Use a more complete alternative memory test. 540 541endif 542 543config CMD_MX_CYCLIC 544 bool "mdc, mwc" 545 help 546 mdc - memory display cyclic 547 mwc - memory write cyclic 548 549config CMD_SHA1SUM 550 bool "sha1sum" 551 select SHA1 552 help 553 Compute SHA1 checksum. 554 555config SHA1SUM_VERIFY 556 bool "sha1sum -v" 557 depends on CMD_SHA1SUM 558 help 559 Add -v option to verify data against a SHA1 checksum. 560 561config CMD_STRINGS 562 bool "strings - display strings in memory" 563 help 564 This works similarly to the Unix 'strings' command except that it 565 works with a memory range. String of printable characters found 566 within the range are displayed. The minimum number of characters 567 for a sequence to be considered a string can be provided. 568 569endmenu 570 571menu "Compression commands" 572 573config CMD_LZMADEC 574 bool "lzmadec" 575 default y if CMD_BOOTI 576 select LZMA 577 help 578 Support decompressing an LZMA (Lempel-Ziv-Markov chain algorithm) 579 image from memory. 580 581config CMD_UNZIP 582 bool "unzip" 583 default y if CMD_BOOTI 584 help 585 Uncompress a zip-compressed memory region. 586 587config CMD_ZIP 588 bool "zip" 589 help 590 Compress a memory region with zlib deflate method. 591 592endmenu 593 594menu "Device access commands" 595 596config CMD_ARMFLASH 597 #depends on FLASH_CFI_DRIVER 598 bool "armflash" 599 help 600 ARM Ltd reference designs flash partition access 601 602config CMD_ADC 603 bool "adc - Access Analog to Digital Converters info and data" 604 select ADC 605 select DM_REGULATOR 606 help 607 Shows ADC device info and permit printing one-shot analog converted 608 data from a named Analog to Digital Converter. 609 610config CMD_CLK 611 bool "clk - Show clock frequencies" 612 help 613 (deprecated) 614 Shows clock frequences by calling a sock_clk_dump() hook function. 615 This is depreated in favour of using the CLK uclass and accessing 616 clock values from associated drivers. However currently no command 617 exists for this. 618 619config CMD_DEMO 620 bool "demo - Demonstration commands for driver model" 621 depends on DM 622 help 623 Provides a 'demo' command which can be used to play around with 624 driver model. To use this properly you will need to enable one or 625 both of the demo devices (DM_DEMO_SHAPE and DM_DEMO_SIMPLE). 626 Otherwise you will always get an empty list of devices. The demo 627 devices are defined in the sandbox device tree, so the easiest 628 option is to use sandbox and pass the -d point to sandbox's 629 u-boot.dtb file. 630 631config CMD_DFU 632 bool "dfu" 633 select DFU 634 help 635 Enables the command "dfu" which is used to have U-Boot create a DFU 636 class device via USB. This command requires that the "dfu_alt_info" 637 environment variable be set and define the alt settings to expose to 638 the host. 639 640config CMD_DM 641 bool "dm - Access to driver model information" 642 depends on DM 643 help 644 Provides access to driver model data structures and information, 645 such as a list of devices, list of uclasses and the state of each 646 device (e.g. activated). This is not required for operation, but 647 can be useful to see the state of driver model for debugging or 648 interest. 649 650config CMD_FASTBOOT 651 bool "fastboot - Android fastboot support" 652 depends on FASTBOOT 653 help 654 This enables the command "fastboot" which enables the Android 655 fastboot mode for the platform. Fastboot is a protocol for 656 downloading images, flashing and device control used on 657 Android devices. Fastboot requires either the network stack 658 enabled or support for acting as a USB device. 659 660 See doc/README.android-fastboot for more information. 661 662config CMD_FDC 663 bool "fdcboot - Boot from floppy device" 664 help 665 The 'fdtboot' command allows booting an image from a floppy disk. 666 667config CMD_FLASH 668 bool "flinfo, erase, protect" 669 default y 670 help 671 NOR flash support. 672 flinfo - print FLASH memory information 673 erase - FLASH memory 674 protect - enable or disable FLASH write protection 675 676config CMD_FPGA 677 bool "fpga" 678 depends on FPGA 679 default y 680 help 681 FPGA support. 682 683config CMD_FPGA_LOADBP 684 bool "fpga loadbp - load partial bitstream (Xilinx only)" 685 depends on CMD_FPGA 686 help 687 Supports loading an FPGA device from a bitstream buffer containing 688 a partial bitstream. 689 690config CMD_FPGA_LOADFS 691 bool "fpga loadfs - load bitstream from FAT filesystem (Xilinx only)" 692 depends on CMD_FPGA 693 help 694 Supports loading an FPGA device from a FAT filesystem. 695 696config CMD_FPGA_LOADMK 697 bool "fpga loadmk - load bitstream from image" 698 depends on CMD_FPGA 699 help 700 Supports loading an FPGA device from a image generated by mkimage. 701 702config CMD_FPGA_LOADP 703 bool "fpga loadp - load partial bitstream" 704 depends on CMD_FPGA 705 help 706 Supports loading an FPGA device from a bitstream buffer containing 707 a partial bitstream. 708 709config CMD_FPGA_LOAD_SECURE 710 bool "fpga loads - loads secure bitstreams (Xilinx only)" 711 depends on CMD_FPGA 712 help 713 Enables the fpga loads command which is used to load secure 714 (authenticated or encrypted or both) bitstreams on to FPGA. 715 716config CMD_FPGAD 717 bool "fpgad - dump FPGA registers" 718 help 719 (legacy, needs conversion to driver model) 720 Provides a way to dump FPGA registers by calling the board-specific 721 fpga_get_reg() function. This functions similarly to the 'md' 722 command. 723 724config CMD_FUSE 725 bool "fuse - support for the fuse subssystem" 726 help 727 (deprecated - needs conversion to driver model) 728 This allows reading, sensing, programming or overriding fuses 729 which control the behaviour of the device. The command uses the 730 fuse_...() API. 731 732config CMD_GPIO 733 bool "gpio" 734 help 735 GPIO support. 736 737config CMD_GPT 738 bool "GPT (GUID Partition Table) command" 739 select EFI_PARTITION 740 select HAVE_BLOCK_DEVICE 741 select PARTITION_UUIDS 742 imply RANDOM_UUID 743 help 744 Enable the 'gpt' command to ready and write GPT style partition 745 tables. 746 747config RANDOM_UUID 748 bool "GPT Random UUID generation" 749 select LIB_UUID 750 help 751 Enable the generation of partitions with random UUIDs if none 752 are provided. 753 754config CMD_GPT_RENAME 755 bool "GPT partition renaming commands" 756 depends on CMD_GPT 757 help 758 Enables the 'gpt' command to interchange names on two GPT 759 partitions via the 'gpt swap' command or to rename single 760 partitions via the 'rename' command. 761 762config CMD_IDE 763 bool "ide - Support for IDE drivers" 764 select IDE 765 help 766 Provides an 'ide' command which allows accessing the IDE drive, 767 reseting the IDE interface, printing the partition table and 768 geting device info. It also enables the 'diskboot' command which 769 permits booting from an IDE drive. 770 771config CMD_IO 772 bool "io - Support for performing I/O accesses" 773 help 774 Provides an 'iod' command to display I/O space and an 'iow' command 775 to write values to the I/O space. This can be useful for manually 776 checking the state of devices during boot when debugging device 777 drivers, etc. 778 779config CMD_IOTRACE 780 bool "iotrace - Support for tracing I/O activity" 781 help 782 Provides an 'iotrace' command which supports recording I/O reads and 783 writes in a trace buffer in memory . It also maintains a checksum 784 of the trace records (even if space is exhausted) so that the 785 sequence of I/O accesses can be verified. 786 787 When debugging drivers it is useful to see what I/O accesses were 788 done and in what order. 789 790 Even if the individual accesses are of little interest it can be 791 useful to verify that the access pattern is consistent each time 792 an operation is performed. In this case a checksum can be used to 793 characterise the operation of a driver. The checksum can be compared 794 across different runs of the operation to verify that the driver is 795 working properly. 796 797 In particular, when performing major refactoring of the driver, where 798 the access pattern should not change, the checksum provides assurance 799 that the refactoring work has not broken the driver. 800 801 This works by sneaking into the io.h heder for an architecture and 802 redirecting I/O accesses through iotrace's tracing mechanism. 803 804 For now no commands are provided to examine the trace buffer. The 805 format is fairly simple, so 'md' is a reasonable substitute. 806 807 Note: The checksum feature is only useful for I/O regions where the 808 contents do not change outside of software control. Where this is not 809 suitable you can fall back to manually comparing the addresses. It 810 might be useful to enhance tracing to only checksum the accesses and 811 not the data read/written. 812 813config CMD_I2C 814 bool "i2c" 815 help 816 I2C support. 817 818config CMD_LOADB 819 bool "loadb" 820 default y 821 help 822 Load a binary file over serial line. 823 824config CMD_LOADS 825 bool "loads" 826 default y 827 help 828 Load an S-Record file over serial line 829 830config CMD_MMC 831 bool "mmc" 832 help 833 MMC memory mapped support. 834 835config CMD_MMC_RPMB 836 bool "Enable support for RPMB in the mmc command" 837 depends on CMD_MMC 838 help 839 Enable the commands for reading, writing and programming the 840 key for the Replay Protection Memory Block partition in eMMC. 841 842config CMD_MMC_SWRITE 843 bool "mmc swrite" 844 depends on CMD_MMC && MMC_WRITE 845 select IMAGE_SPARSE 846 help 847 Enable support for the "mmc swrite" command to write Android sparse 848 images to eMMC. 849 850config CMD_NAND 851 bool "nand" 852 default y if NAND_SUNXI 853 help 854 NAND support. 855 856if CMD_NAND 857config CMD_NAND_TRIMFFS 858 bool "nand write.trimffs" 859 default y if ARCH_SUNXI 860 help 861 Allows one to skip empty pages when flashing something on a NAND. 862 863config CMD_NAND_LOCK_UNLOCK 864 bool "nand lock/unlock" 865 help 866 NAND locking support. 867 868config CMD_NAND_TORTURE 869 bool "nand torture" 870 help 871 NAND torture support. 872 873endif # CMD_NAND 874 875config CMD_NVME 876 bool "nvme" 877 depends on NVME 878 default y if NVME 879 help 880 NVM Express device support 881 882config CMD_MMC_SPI 883 bool "mmc_spi - Set up MMC SPI device" 884 help 885 Provides a way to set up an MMC (Multimedia Card) SPI (Serial 886 Peripheral Interface) device. The device provides a means of 887 accessing an MMC device via SPI using a single data line, limited 888 to 20MHz. It is useful since it reduces the amount of protocol code 889 required. 890 891config CMD_ONENAND 892 bool "onenand - access to onenand device" 893 help 894 OneNAND is a brand of NAND ('Not AND' gate) flash which provides 895 various useful features. This command allows reading, writing, 896 and erasing blocks. It allso provides a way to show and change 897 bad blocks, and test the device. 898 899config CMD_PART 900 bool "part" 901 select HAVE_BLOCK_DEVICE 902 select PARTITION_UUIDS 903 help 904 Read and display information about the partition table on 905 various media. 906 907config CMD_PCI 908 bool "pci - Access PCI devices" 909 help 910 Provide access to PCI (Peripheral Interconnect Bus), a type of bus 911 used on some devices to allow the CPU to communicate with its 912 peripherals. Sub-commands allow bus enumeration, displaying and 913 changing configuration space and a few other features. 914 915config CMD_PCMCIA 916 bool "pinit - Set up PCMCIA device" 917 help 918 Provides a means to initialise a PCMCIA (Personal Computer Memory 919 Card International Association) device. This is an old standard from 920 about 1990. These devices are typically removable memory or network 921 cards using a standard 68-pin connector. 922 923config CMD_READ 924 bool "read - Read binary data from a partition" 925 help 926 Provides low-level access to the data in a partition. 927 928config CMD_REMOTEPROC 929 bool "remoteproc" 930 depends on REMOTEPROC 931 help 932 Support for Remote Processor control 933 934config CMD_SATA 935 bool "sata - Access SATA subsystem" 936 select SATA 937 help 938 SATA (Serial Advanced Technology Attachment) is a serial bus 939 standard for connecting to hard drives and other storage devices. 940 This command provides information about attached devices and allows 941 reading, writing and other operations. 942 943 SATA replaces PATA (originally just ATA), which stands for Parallel AT 944 Attachment, where AT refers to an IBM AT (Advanced Technology) 945 computer released in 1984. 946 947config CMD_SAVES 948 bool "saves - Save a file over serial in S-Record format" 949 help 950 Provides a way to save a binary file using the Motorola S-Record 951 format over the serial line. 952 953config CMD_SCSI 954 bool "scsi - Access to SCSI devices" 955 default y if SCSI 956 help 957 This provides a 'scsi' command which provides access to SCSI (Small 958 Computer System Interface) devices. The command provides a way to 959 scan the bus, reset the bus, read and write data and get information 960 about devices. 961 962config CMD_SDRAM 963 bool "sdram - Print SDRAM configuration information" 964 help 965 Provides information about attached SDRAM. This assumed that the 966 SDRAM has an EEPROM with information that can be read using the 967 I2C bus. This is only available on some boards. 968 969config CMD_SF 970 bool "sf" 971 help 972 SPI Flash support 973 974config CMD_SF_TEST 975 bool "sf test - Allow testing of SPI flash" 976 help 977 Provides a way to test that SPI flash is working correctly. The 978 test is destructive, in that an area of SPI flash must be provided 979 for the test to use. Performance information is also provided, 980 measuring the performance of reading, writing and erasing in 981 Mbps (Million Bits Per Second). This value should approximately 982 equal the SPI bus speed for a single-bit-wide SPI bus, assuming 983 everything is working properly. 984 985config CMD_SPI 986 bool "sspi" 987 help 988 SPI utility command. 989 990config CMD_TSI148 991 bool "tsi148 - Command to access tsi148 device" 992 help 993 This provides various sub-commands to initialise and configure the 994 Turndra tsi148 device. See the command help for full details. 995 996config CMD_UNIVERSE 997 bool "universe - Command to set up the Turndra Universe controller" 998 help 999 This allows setting up the VMEbus provided by this controller. 1000 See the command help for full details. 1001 1002config CMD_USB 1003 bool "usb" 1004 select HAVE_BLOCK_DEVICE 1005 help 1006 USB support. 1007 1008config CMD_USB_SDP 1009 bool "sdp" 1010 select USB_FUNCTION_SDP 1011 help 1012 Enables the command "sdp" which is used to have U-Boot emulating the 1013 Serial Download Protocol (SDP) via USB. 1014 1015config CMD_ROCKUSB 1016 bool "rockusb" 1017 depends on USB_FUNCTION_ROCKUSB 1018 help 1019 Rockusb protocol is widely used by Rockchip SoC based devices. It can 1020 read/write info, image to/from devices. This enable rockusb command 1021 support to communication with rockusb device. for more detail about 1022 this command, please read doc/README.rockusb. 1023 1024config CMD_USB_MASS_STORAGE 1025 bool "UMS usb mass storage" 1026 select USB_FUNCTION_MASS_STORAGE 1027 help 1028 USB mass storage support 1029 1030endmenu 1031 1032 1033menu "Shell scripting commands" 1034 1035config CMD_ECHO 1036 bool "echo" 1037 default y 1038 help 1039 Echo args to console 1040 1041config CMD_ITEST 1042 bool "itest" 1043 default y 1044 help 1045 Return true/false on integer compare. 1046 1047config CMD_SOURCE 1048 bool "source" 1049 default y 1050 help 1051 Run script from memory 1052 1053config CMD_SETEXPR 1054 bool "setexpr" 1055 default y 1056 help 1057 Evaluate boolean and math expressions and store the result in an env 1058 variable. 1059 Also supports loading the value at a memory location into a variable. 1060 If CONFIG_REGEX is enabled, setexpr also supports a gsub function. 1061 1062endmenu 1063 1064if NET 1065 1066menuconfig CMD_NET 1067 bool "Network commands" 1068 default y 1069 1070if CMD_NET 1071 1072config CMD_BOOTP 1073 bool "bootp" 1074 default y 1075 help 1076 bootp - boot image via network using BOOTP/TFTP protocol 1077 1078config CMD_DHCP 1079 bool "dhcp" 1080 depends on CMD_BOOTP 1081 help 1082 Boot image via network using DHCP/TFTP protocol 1083 1084config BOOTP_BOOTPATH 1085 bool "Request & store 'rootpath' from BOOTP/DHCP server" 1086 default y 1087 depends on CMD_BOOTP 1088 help 1089 Even though the config is called BOOTP_BOOTPATH, it stores the 1090 path in the variable 'rootpath'. 1091 1092config BOOTP_DNS 1093 bool "Request & store 'dnsip' from BOOTP/DHCP server" 1094 default y 1095 depends on CMD_BOOTP 1096 help 1097 The primary DNS server is stored as 'dnsip'. If two servers are 1098 returned, you must set BOOTP_DNS2 to store that second server IP 1099 also. 1100 1101config BOOTP_DNS2 1102 bool "Store 'dnsip2' from BOOTP/DHCP server" 1103 depends on BOOTP_DNS 1104 help 1105 If a DHCP client requests the DNS server IP from a DHCP server, 1106 it is possible that more than one DNS serverip is offered to the 1107 client. If CONFIG_BOOTP_DNS2 is enabled, the secondary DNS 1108 server IP will be stored in the additional environment 1109 variable "dnsip2". The first DNS serverip is always 1110 stored in the variable "dnsip", when BOOTP_DNS is defined. 1111 1112config BOOTP_GATEWAY 1113 bool "Request & store 'gatewayip' from BOOTP/DHCP server" 1114 default y 1115 depends on CMD_BOOTP 1116 1117config BOOTP_HOSTNAME 1118 bool "Request & store 'hostname' from BOOTP/DHCP server" 1119 default y 1120 depends on CMD_BOOTP 1121 help 1122 The name may or may not be qualified with the local domain name. 1123 1124config BOOTP_PREFER_SERVERIP 1125 bool "serverip variable takes precedent over DHCP server IP." 1126 depends on CMD_BOOTP 1127 help 1128 By default a BOOTP/DHCP reply will overwrite the 'serverip' variable. 1129 1130 With this option enabled, the 'serverip' variable in the environment 1131 takes precedence over DHCP server IP and will only be set by the DHCP 1132 server if not already set in the environment. 1133 1134config BOOTP_SUBNETMASK 1135 bool "Request & store 'netmask' from BOOTP/DHCP server" 1136 default y 1137 depends on CMD_BOOTP 1138 1139config BOOTP_NTPSERVER 1140 bool "Request & store 'ntpserverip' from BOOTP/DHCP server" 1141 depends on CMD_BOOTP 1142 1143config BOOTP_PXE 1144 bool "Send PXE client arch to BOOTP/DHCP server" 1145 default y 1146 depends on CMD_BOOTP && CMD_PXE 1147 help 1148 Supported for ARM, ARM64, and x86 for now. 1149 1150config BOOTP_PXE_CLIENTARCH 1151 hex 1152 depends on BOOTP_PXE 1153 default 0x16 if ARM64 1154 default 0x15 if ARM 1155 default 0 if X86 1156 1157config BOOTP_VCI_STRING 1158 string 1159 depends on CMD_BOOTP 1160 default "U-Boot.armv7" if CPU_V7A || CPU_V7M || CPU_V7R 1161 default "U-Boot.armv8" if ARM64 1162 default "U-Boot.arm" if ARM 1163 default "U-Boot" 1164 1165config CMD_TFTPBOOT 1166 bool "tftpboot" 1167 default y 1168 help 1169 tftpboot - boot image via network using TFTP protocol 1170 1171config CMD_TFTPPUT 1172 bool "tftp put" 1173 depends on CMD_TFTPBOOT 1174 help 1175 TFTP put command, for uploading files to a server 1176 1177config CMD_TFTPSRV 1178 bool "tftpsrv" 1179 depends on CMD_TFTPBOOT 1180 help 1181 Act as a TFTP server and boot the first received file 1182 1183config NET_TFTP_VARS 1184 bool "Control TFTP timeout and count through environment" 1185 depends on CMD_TFTPBOOT 1186 default y 1187 help 1188 If set, allows controlling the TFTP timeout through the 1189 environment variable tftptimeout, and the TFTP maximum 1190 timeout count through the variable tftptimeoutcountmax. 1191 If unset, timeout and maximum are hard-defined as 1 second 1192 and 10 timouts per TFTP transfer. 1193 1194config CMD_RARP 1195 bool "rarpboot" 1196 help 1197 Boot image via network using RARP/TFTP protocol 1198 1199config CMD_NFS 1200 bool "nfs" 1201 default y 1202 help 1203 Boot image via network using NFS protocol. 1204 1205config CMD_MII 1206 bool "mii" 1207 help 1208 Enable MII utility commands. 1209 1210config CMD_PING 1211 bool "ping" 1212 help 1213 Send ICMP ECHO_REQUEST to network host 1214 1215config CMD_CDP 1216 bool "cdp" 1217 help 1218 Perform CDP network configuration 1219 1220config CMD_SNTP 1221 bool "sntp" 1222 help 1223 Synchronize RTC via network 1224 1225config CMD_DNS 1226 bool "dns" 1227 help 1228 Lookup the IP of a hostname 1229 1230config CMD_LINK_LOCAL 1231 bool "linklocal" 1232 select LIB_RAND 1233 help 1234 Acquire a network IP address using the link-local protocol 1235 1236endif 1237 1238config CMD_ETHSW 1239 bool "ethsw" 1240 help 1241 Allow control of L2 Ethernet switch commands. These are supported 1242 by the vsc9953 Ethernet driver at present. Sub-commands allow 1243 operations such as enabling / disabling a port and 1244 viewing/maintaining the filtering database (FDB) 1245 1246config CMD_PXE 1247 bool "pxe" 1248 select MENU 1249 help 1250 Boot image via network using PXE protocol 1251 1252config CMD_WOL 1253 bool "wol" 1254 help 1255 Wait for wake-on-lan Magic Packet 1256 1257endif 1258 1259menu "Misc commands" 1260 1261config CMD_BMP 1262 bool "Enable 'bmp' command" 1263 depends on LCD || DM_VIDEO || VIDEO 1264 help 1265 This provides a way to obtain information about a BMP-format iamge 1266 and to display it. BMP (which presumably stands for BitMaP) is a 1267 file format defined by Microsoft which supports images of various 1268 depths, formats and compression methods. Headers on the file 1269 determine the formats used. This command can be used by first loading 1270 the image into RAM, then using this command to look at it or display 1271 it. 1272 1273config CMD_BOOTCOUNT 1274 bool "bootcount" 1275 depends on BOOTCOUNT_LIMIT 1276 help 1277 Enable the bootcount command, which allows interrogation and 1278 reset of the bootcounter. 1279 1280config CMD_BSP 1281 bool "Enable board-specific commands" 1282 help 1283 (deprecated: instead, please define a Kconfig option for each command) 1284 1285 Some boards have board-specific commands which are only enabled 1286 during developemnt and need to be turned off for production. This 1287 option provides a way to control this. The commands that are enabled 1288 vary depending on the board. 1289 1290config CMD_BKOPS_ENABLE 1291 bool "mmc bkops enable" 1292 depends on CMD_MMC 1293 default n 1294 help 1295 Enable command for setting manual background operations handshake 1296 on a eMMC device. The feature is optionally available on eMMC devices 1297 conforming to standard >= 4.41. 1298 1299config CMD_BLOCK_CACHE 1300 bool "blkcache - control and stats for block cache" 1301 depends on BLOCK_CACHE 1302 default y if BLOCK_CACHE 1303 help 1304 Enable the blkcache command, which can be used to control the 1305 operation of the cache functions. 1306 This is most useful when fine-tuning the operation of the cache 1307 during development, but also allows the cache to be disabled when 1308 it might hurt performance (e.g. when using the ums command). 1309 1310config CMD_CACHE 1311 bool "icache or dcache" 1312 help 1313 Enable the "icache" and "dcache" commands 1314 1315config CMD_DISPLAY 1316 bool "Enable the 'display' command, for character displays" 1317 help 1318 (this needs porting to driver model) 1319 This enables the 'display' command which allows a string to be 1320 displayed on a simple board-specific display. Implement 1321 display_putc() to use it. 1322 1323config CMD_LED 1324 bool "led" 1325 default y if LED 1326 help 1327 Enable the 'led' command which allows for control of LEDs supported 1328 by the board. The LEDs can be listed with 'led list' and controlled 1329 with led on/off/togle/blink. Any LED drivers can be controlled with 1330 this command, e.g. led_gpio. 1331 1332config CMD_DATE 1333 bool "date" 1334 default y if DM_RTC 1335 help 1336 Enable the 'date' command for getting/setting the time/date in RTC 1337 devices. 1338 1339config CMD_TIME 1340 bool "time" 1341 help 1342 Run commands and summarize execution time. 1343 1344config CMD_GETTIME 1345 bool "gettime - read elapsed time" 1346 help 1347 Enable the 'gettime' command which reads the elapsed time since 1348 U-Boot started running. This shows the time in seconds and 1349 milliseconds. See also the 'bootstage' command which provides more 1350 flexibility for boot timing. 1351 1352# TODO: rename to CMD_SLEEP 1353config CMD_MISC 1354 bool "sleep" 1355 default y 1356 help 1357 Delay execution for some time 1358 1359config MP 1360 bool "support for multiprocessor" 1361 help 1362 This provides an option to brinup 1363 different processors in multiprocessor 1364 cases. 1365 1366config CMD_TIMER 1367 bool "timer" 1368 help 1369 Access the system timer. 1370 1371config CMD_SOUND 1372 bool "sound" 1373 depends on SOUND 1374 help 1375 This provides basic access to the U-Boot's sound support. The main 1376 feature is to play a beep. 1377 1378 sound init - set up sound system 1379 sound play - play a sound 1380 1381config CMD_QFW 1382 bool "qfw" 1383 select QFW 1384 help 1385 This provides access to the QEMU firmware interface. The main 1386 feature is to allow easy loading of files passed to qemu-system 1387 via -kernel / -initrd 1388 1389source "cmd/mvebu/Kconfig" 1390 1391config CMD_TERMINAL 1392 bool "terminal - provides a way to attach a serial terminal" 1393 help 1394 Provides a 'cu'-like serial terminal command. This can be used to 1395 access other serial ports from the system console. The terminal 1396 is very simple with no special processing of characters. As with 1397 cu, you can press ~. (tilde followed by period) to exit. 1398 1399config CMD_UUID 1400 bool "uuid, guid - generation of unique IDs" 1401 select LIB_UUID 1402 help 1403 This enables two commands: 1404 1405 uuid - generate random Universally Unique Identifier 1406 guid - generate Globally Unique Identifier based on random UUID 1407 1408 The two commands are very similar except for the endianness of the 1409 output. 1410 1411endmenu 1412 1413source "cmd/ti/Kconfig" 1414 1415config CMD_BOOTSTAGE 1416 bool "Enable the 'bootstage' command" 1417 depends on BOOTSTAGE 1418 help 1419 Add a 'bootstage' command which supports printing a report 1420 and un/stashing of bootstage data. 1421 1422menu "Power commands" 1423config CMD_PMIC 1424 bool "Enable Driver Model PMIC command" 1425 depends on DM_PMIC 1426 help 1427 This is the pmic command, based on a driver model pmic's API. 1428 Command features are unchanged: 1429 - list - list pmic devices 1430 - pmic dev <id> - show or [set] operating pmic device (NEW) 1431 - pmic dump - dump registers 1432 - pmic read address - read byte of register at address 1433 - pmic write address - write byte to register at address 1434 The only one change for this command is 'dev' subcommand. 1435 1436config CMD_REGULATOR 1437 bool "Enable Driver Model REGULATOR command" 1438 depends on DM_REGULATOR 1439 help 1440 This command is based on driver model regulator's API. 1441 User interface features: 1442 - list - list regulator devices 1443 - regulator dev <id> - show or [set] operating regulator device 1444 - regulator info - print constraints info 1445 - regulator status - print operating status 1446 - regulator value <val] <-f> - print/[set] voltage value [uV] 1447 - regulator current <val> - print/[set] current value [uA] 1448 - regulator mode <id> - print/[set] operating mode id 1449 - regulator enable - enable the regulator output 1450 - regulator disable - disable the regulator output 1451 1452 The '-f' (force) option can be used for set the value which exceeds 1453 the limits, which are found in device-tree and are kept in regulator's 1454 uclass platdata structure. 1455 1456endmenu 1457 1458menu "Security commands" 1459config CMD_AES 1460 bool "Enable the 'aes' command" 1461 select AES 1462 help 1463 This provides a means to encrypt and decrypt data using the AES 1464 (Advanced Encryption Standard). This algorithm uses a symetric key 1465 and is widely used as a streaming cipher. Different key lengths are 1466 supported by the algorithm but this command only supports 128 bits 1467 at present. 1468 1469config CMD_BLOB 1470 bool "Enable the 'blob' command" 1471 help 1472 This is used with the Freescale secure boot mechanism. 1473 1474 Freescale's SEC block has built-in Blob Protocol which provides 1475 a method for protecting user-defined data across system power 1476 cycles. SEC block protects data in a data structure called a Blob, 1477 which provides both confidentiality and integrity protection. 1478 1479 Encapsulating data as a blob 1480 Each time that the Blob Protocol is used to protect data, a 1481 different randomly generated key is used to encrypt the data. 1482 This random key is itself encrypted using a key which is derived 1483 from SoC's non-volatile secret key and a 16 bit Key identifier. 1484 The resulting encrypted key along with encrypted data is called a 1485 blob. The non-volatile secure key is available for use only during 1486 secure boot. 1487 1488 During decapsulation, the reverse process is performed to get back 1489 the original data. 1490 1491 Sub-commands: 1492 blob enc - encapsulating data as a cryptgraphic blob 1493 blob dec - decapsulating cryptgraphic blob to get the data 1494 1495 Syntax: 1496 1497 blob enc src dst len km 1498 1499 Encapsulate and create blob of data $len bytes long 1500 at address $src and store the result at address $dst. 1501 $km is the 16 byte key modifier is also required for 1502 generation/use as key for cryptographic operation. Key 1503 modifier should be 16 byte long. 1504 1505 blob dec src dst len km 1506 1507 Decapsulate the blob of data at address $src and 1508 store result of $len byte at addr $dst. 1509 $km is the 16 byte key modifier is also required for 1510 generation/use as key for cryptographic operation. Key 1511 modifier should be 16 byte long. 1512 1513config CMD_HASH 1514 bool "Support 'hash' command" 1515 select HASH 1516 help 1517 This provides a way to hash data in memory using various supported 1518 algorithms (such as SHA1, MD5, CRC32). The computed digest can be 1519 saved to memory or to an environment variable. It is also possible 1520 to verify a hash against data in memory. 1521 1522config CMD_HVC 1523 bool "Support the 'hvc' command" 1524 depends on ARM_SMCCC 1525 help 1526 Allows issuing Hypervisor Calls (HVCs). Mostly useful for 1527 development and testing. 1528 1529config CMD_SMC 1530 bool "Support the 'smc' command" 1531 depends on ARM_SMCCC 1532 help 1533 Allows issuing Secure Monitor Calls (SMCs). Mostly useful for 1534 development and testing. 1535 1536config HASH_VERIFY 1537 bool "hash -v" 1538 depends on CMD_HASH 1539 help 1540 Add -v option to verify data against a hash. 1541 1542config CMD_TPM_V1 1543 bool 1544 1545config CMD_TPM_V2 1546 bool 1547 1548config CMD_TPM 1549 bool "Enable the 'tpm' command" 1550 depends on TPM_V1 || TPM_V2 1551 select CMD_TPM_V1 if TPM_V1 1552 select CMD_TPM_V2 if TPM_V2 1553 help 1554 This provides a means to talk to a TPM from the command line. A wide 1555 range of commands if provided - see 'tpm help' for details. The 1556 command requires a suitable TPM on your board and the correct driver 1557 must be enabled. 1558 1559if CMD_TPM 1560 1561config CMD_TPM_TEST 1562 bool "Enable the 'tpm test' command" 1563 depends on TPM_V1 1564 help 1565 This provides a a series of tests to confirm that the TPMv1.x is 1566 working correctly. The tests cover initialisation, non-volatile RAM, 1567 extend, global lock and checking that timing is within expectations. 1568 The tests pass correctly on Infineon TPMs but may need to be adjusted 1569 for other devices. 1570 1571endif 1572 1573endmenu 1574 1575menu "Firmware commands" 1576config CMD_CROS_EC 1577 bool "Enable crosec command" 1578 depends on CROS_EC 1579 default y 1580 help 1581 Enable command-line access to the Chrome OS EC (Embedded 1582 Controller). This provides the 'crosec' command which has 1583 a number of sub-commands for performing EC tasks such as 1584 updating its flash, accessing a small saved context area 1585 and talking to the I2C bus behind the EC (if there is one). 1586endmenu 1587 1588menu "Filesystem commands" 1589config CMD_BTRFS 1590 bool "Enable the 'btrsubvol' command" 1591 select FS_BTRFS 1592 help 1593 This enables the 'btrsubvol' command to list subvolumes 1594 of a BTRFS filesystem. There are no special commands for 1595 listing BTRFS directories or loading BTRFS files - this 1596 can be done by the generic 'fs' commands (see CMD_FS_GENERIC) 1597 when BTRFS is enabled (see FS_BTRFS). 1598 1599config CMD_CBFS 1600 bool "Enable the 'cbfs' command" 1601 depends on FS_CBFS 1602 help 1603 Define this to enable support for reading from a Coreboot 1604 filesystem. This is a ROM-based filesystem used for accessing files 1605 on systems that use coreboot as the first boot-loader and then load 1606 U-Boot to actually boot the Operating System. Available commands are 1607 cbfsinit, cbfsinfo, cbfsls and cbfsload. 1608 1609config CMD_CRAMFS 1610 bool "Enable the 'cramfs' command" 1611 depends on FS_CRAMFS 1612 help 1613 This provides commands for dealing with CRAMFS (Compressed ROM 1614 filesystem). CRAMFS is useful when space is tight since files are 1615 compressed. Two commands are provided: 1616 1617 cramfsls - lists files in a cramfs image 1618 cramfsload - loads a file from a cramfs image 1619 1620config CMD_EXT2 1621 bool "ext2 command support" 1622 select FS_EXT4 1623 help 1624 Enables EXT2 FS command 1625 1626config CMD_EXT4 1627 bool "ext4 command support" 1628 select FS_EXT4 1629 help 1630 Enables EXT4 FS command 1631 1632config CMD_EXT4_WRITE 1633 depends on CMD_EXT4 1634 bool "ext4 write command support" 1635 select EXT4_WRITE 1636 help 1637 Enables EXT4 FS write command 1638 1639config CMD_FAT 1640 bool "FAT command support" 1641 select FS_FAT 1642 help 1643 Support for the FAT fs 1644 1645config CMD_FS_GENERIC 1646 bool "filesystem commands" 1647 help 1648 Enables filesystem commands (e.g. load, ls) that work for multiple 1649 fs types. 1650 1651config CMD_FS_UUID 1652 bool "fsuuid command" 1653 help 1654 Enables fsuuid command for filesystem UUID. 1655 1656config CMD_JFFS2 1657 bool "jffs2 command" 1658 select FS_JFFS2 1659 help 1660 Enables commands to support the JFFS2 (Journalling Flash File System 1661 version 2) filesystem. This enables fsload, ls and fsinfo which 1662 provide the ability to load files, list directories and obtain 1663 filesystem information. 1664 1665config CMD_MTDPARTS 1666 bool "MTD partition support" 1667 select MTD_DEVICE if (CMD_NAND || NAND) 1668 help 1669 MTD partition support 1670 1671config MTDIDS_DEFAULT 1672 string "Default MTD IDs" 1673 depends on CMD_MTDPARTS || CMD_NAND || CMD_FLASH 1674 help 1675 Defines a default MTD IDs list for use with MTD partitions in the 1676 Linux MTD command line partitions format. 1677 1678config MTDPARTS_DEFAULT 1679 string "Default MTD partition scheme" 1680 depends on CMD_MTDPARTS || CMD_NAND || CMD_FLASH 1681 help 1682 Defines a default MTD partitioning scheme in the Linux MTD command 1683 line partitions format 1684 1685config CMD_MTDPARTS_SPREAD 1686 bool "Padd partition size to take account of bad blocks" 1687 depends on CMD_MTDPARTS 1688 help 1689 This enables the 'spread' sub-command of the mtdparts command. 1690 This command will modify the existing mtdparts variable by increasing 1691 the size of the partitions such that 1) each partition's net size is 1692 at least as large as the size specified in the mtdparts variable and 1693 2) each partition starts on a good block. 1694 1695config CMD_REISER 1696 bool "reiser - Access to reiserfs filesystems" 1697 help 1698 This provides two commands which operate on a resierfs filesystem, 1699 commonly used some years ago: 1700 1701 reiserls - list files 1702 reiserload - load a file 1703 1704config CMD_YAFFS2 1705 bool "yaffs2 - Access of YAFFS2 filesystem" 1706 depends on YAFFS2 1707 default y 1708 help 1709 This provides commands for accessing a YAFFS2 filesystem. Yet 1710 Another Flash Filesystem 2 is a filesystem designed specifically 1711 for NAND flash. It incorporates bad-block management and ensures 1712 that device writes are sequential regardless of filesystem 1713 activity. 1714 1715config CMD_ZFS 1716 bool "zfs - Access of ZFS filesystem" 1717 help 1718 This provides commands to accessing a ZFS filesystem, commonly used 1719 on Solaris systems. Two sub-commands are provided: 1720 1721 zfsls - list files in a directory 1722 zfsload - load a file 1723 1724 See doc/README.zfs for more details. 1725 1726endmenu 1727 1728menu "Debug commands" 1729 1730config CMD_BEDBUG 1731 bool "bedbug" 1732 help 1733 The bedbug (emBEDded deBUGger) command provides debugging features 1734 for some PowerPC processors. For details please see the 1735 docuemntation in doc/README.beddbug 1736 1737config CMD_DIAG 1738 bool "diag - Board diagnostics" 1739 help 1740 This command provides access to board diagnostic tests. These are 1741 called Power-on Self Tests (POST). The command allows listing of 1742 available tests and running either all the tests, or specific tests 1743 identified by name. 1744 1745config CMD_IRQ 1746 bool "irq - Show information about interrupts" 1747 depends on !ARM && !MIPS && !SH 1748 help 1749 This enables two commands: 1750 1751 interrupts - enable or disable interrupts 1752 irqinfo - print device-specific interrupt information 1753 1754config CMD_KGDB 1755 bool "kgdb - Allow debugging of U-Boot with gdb" 1756 help 1757 This enables a 'kgdb' command which allows gdb to connect to U-Boot 1758 over a serial link for debugging purposes. This allows 1759 single-stepping, inspecting variables, etc. This is supported only 1760 on PowerPC at present. 1761 1762config CMD_LOG 1763 bool "log - Generation, control and access to logging" 1764 select LOG 1765 help 1766 This provides access to logging features. It allows the output of 1767 log data to be controlled to a limited extent (setting up the default 1768 maximum log level for emitting of records). It also provides access 1769 to a command used for testing the log system. 1770 1771config CMD_TRACE 1772 bool "trace - Support tracing of function calls and timing" 1773 help 1774 Enables a command to control using of function tracing within 1775 U-Boot. This allows recording of call traces including timing 1776 information. The command can write data to memory for exporting 1777 for analsys (e.g. using bootchart). See doc/README.trace for full 1778 details. 1779 1780config CMD_AVB 1781 bool "avb - Android Verified Boot 2.0 operations" 1782 depends on AVB_VERIFY 1783 default n 1784 help 1785 Enables a "avb" command to perform verification of partitions using 1786 Android Verified Boot 2.0 functionality. It includes such subcommands: 1787 avb init - initialize avb2 subsystem 1788 avb read_rb - read rollback index 1789 avb write_rb - write rollback index 1790 avb is_unlocked - check device lock state 1791 avb get_uuid - read and print uuid of a partition 1792 avb read_part - read data from partition 1793 avb read_part_hex - read data from partition and output to stdout 1794 avb write_part - write data to partition 1795 avb verify - run full verification chain 1796endmenu 1797 1798config CMD_UBI 1799 tristate "Enable UBI - Unsorted block images commands" 1800 default y if NAND_SUNXI 1801 select CMD_MTDPARTS 1802 select CRC32 1803 select MTD_UBI 1804 help 1805 UBI is a software layer above MTD layer which admits use of LVM-like 1806 logical volumes on top of MTD devices, hides some complexities of 1807 flash chips like wear and bad blocks and provides some other useful 1808 capabilities. Please, consult the MTD web site for more details 1809 (www.linux-mtd.infradead.org). Activate this option if you want 1810 to use U-Boot UBI commands. 1811 1812config CMD_UBIFS 1813 tristate "Enable UBIFS - Unsorted block images filesystem commands" 1814 depends on CMD_UBI 1815 default y if CMD_UBI 1816 select CRC32 1817 select LZO 1818 help 1819 UBIFS is a file system for flash devices which works on top of UBI. 1820 1821endmenu 1822