arm64: dts: uniphier: add sound node

This patch adds audio controller, codec and simple card node of
UniPhier AIO sound system for LD11/20 SoCs.

Signed-off-by: Katsuhiro Suzuki

arm64: dts: uniphier: add sound node

This patch adds audio controller, codec and simple card node of
UniPhier AIO sound system for LD11/20 SoCs.

Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

show more ...

arm64: dts: uniphier: add has-transaction-translator property to usb node for LD11

When a full/low speed device is connected to USB 2.0 port on UniPhier SoC
that has ehci controller, the

arm64: dts: uniphier: add has-transaction-translator property to usb node for LD11

When a full/low speed device is connected to USB 2.0 port on UniPhier SoC
that has ehci controller, the kernel shows the following messages.

| usb usb1-port1: Cannot enable. Maybe the USB cable is bad?
| usb usb1-port1: Cannot enable. Maybe the USB cable is bad?
| usb usb1-port1: Cannot enable. Maybe the USB cable is bad?
| usb usb1-port1: unable to enumerate USB device

To fix the issue, the driver needs to enable Transaction Translator on ehci
root hub. This adds 'has-transaction-translator' property to each node.

Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

show more ...

arm64: dts: uniphier: use macros in dt-bindings header

The dt-bindings header was applied to the driver subsystem. I had to
wait for a merge window to use it from DT.

Signed-of

arm64: dts: uniphier: use macros in dt-bindings header

The dt-bindings header was applied to the driver subsystem. I had to
wait for a merge window to use it from DT.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

show more ...

Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM device-tree updates from Arnd Bergmann:
"We add device tree files for a couple of additional

Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM device-tree updates from Arnd Bergmann:
"We add device tree files for a couple of additional SoCs in various
areas:

Allwinner R40/V40 for entertainment, Broadcom Hurricane 2 for
networking, Amlogic A113D for audio, and Renesas R-Car V3M for
automotive.

As usual, lots of new boards get added based on those and other SoCs:

- Actions S500 based CubieBoard6 single-board computer

- Amlogic Meson-AXG A113D based development board
- Amlogic S912 based Khadas VIM2 single-board computer
- Amlogic S912 based Tronsmart Vega S96 set-top-box

- Allwinner H5 based NanoPi NEO Plus2 single-board computer
- Allwinner R40 based Banana Pi M2 Ultra and Berry single-board computers
- Allwinner A83T based TBS A711 Tablet

- Broadcom Hurricane 2 based Ubiquiti UniFi Switch 8
- Broadcom bcm47xx based Luxul XAP-1440/XAP-810/ABR-4500/XBR-4500
wireless access points and routers

- NXP i.MX51 based Zodiac Inflight Innovations RDU1 board
- NXP i.MX53 based GE Healthcare PPD biometric monitor
- NXP i.MX6 based Pistachio single-board computer
- NXP i.MX6 based Vining-2000 automotive diagnostic interface
- NXP i.MX6 based Ka-Ro TX6 Computer-on-Module in additional variants

- Qualcomm MSM8974 (Snapdragon 800) based Fairphone 2 phone
- Qualcomm MSM8974pro (Snapdragon 801) based Sony Xperia Z2 Tablet

- Realtek RTD1295 based set-top-boxes MeLE V9 and PROBOX2 AVA

- Renesas R-Car V3M (R8A77970) SoC and "Eagle" reference board
- Renesas H3ULCB and M3ULCB "Kingfisher" extension infotainment boards
- Renasas r8a7745 based iWave G22D-SODIMM SoM

- Rockchip rk3288 based Amarula Vyasa single-board computer

- Samsung Exynos5800 based Odroid HC1 single-board computer

For existing SoC support, there was a lot of ongoing work, as usual
most of that concentrated on the Renesas, Rockchip, OMAP, i.MX,
Amlogic and Allwinner platforms, but others were also active.

Rob Herring and many others worked on reducing the number of issues
that the latest version of 'dtc' now warns about. Unfortunately there
is still a lot left to do.

A rework of the ARM foundation model introduced several new files for
common variations of the model"

* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (599 commits)
arm64: dts: uniphier: route on-board device IRQ to GPIO controller for PXs3
dt-bindings: bus: Add documentation for the Technologic Systems NBUS
arm64: dts: actions: s900-bubblegum-96: Add fake uart5 clock
ARM: dts: owl-s500: Add CubieBoard6
dt-bindings: arm: actions: Add CubieBoard6
ARM: dts: owl-s500-guitar-bb-rev-b: Add fake uart3 clock
ARM: dts: owl-s500: Set power domains for CPU2 and CPU3
arm: dts: mt7623: remove unused compatible string for pio node
arm: dts: mt7623: update usb related nodes
arm: dts: mt7623: update crypto node
ARM: dts: sun8i: a711: Enable USB OTG
ARM: dts: sun8i: a711: Add regulator support
ARM: dts: sun8i: a83t: bananapi-m3: Enable AP6212 WiFi on mmc1
ARM: dts: sun8i: a83t: cubietruck-plus: Enable AP6330 WiFi on mmc1
ARM: dts: sun8i: a83t: Move mmc1 pinctrl setting to dtsi file
ARM: dts: sun8i: a83t: allwinner-h8homlet-v2: Add AXP818 regulator nodes
ARM: dts: sun8i: a83t: bananapi-m3: Add AXP813 regulator nodes
ARM: dts: sun8i: a83t: cubietruck-plus: Add AXP818 regulator nodes
ARM: dts: sunxi: Add dtsi for AXP81x PMIC
arm64: dts: allwinner: H5: Restore EMAC changes
...

show more ...

arm64: dts: uniphier: add resets properties

Add resets properties to all nodes that have reset lines.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

arm64: dts: uniphier: add eMMC hardware reset provider node

Add mmc-pwrseq-emmc node to perform standard eMMC hardware reset
procedure.

Signed-off-by: Masahiro Yamada <yamada.ma

arm64: dts: uniphier: add eMMC hardware reset provider node

Add mmc-pwrseq-emmc node to perform standard eMMC hardware reset
procedure.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

show more ...

arm64: dts: uniphier: add GPIO controller nodes

The GPIO controller also acts as an interrupt controller and the
interrupt lines are connected to the AIDET block.

Signed-off-by:

arm64: dts: uniphier: add GPIO controller nodes

The GPIO controller also acts as an interrupt controller and the
interrupt lines are connected to the AIDET block.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

show more ...

arm64: dts: uniphier: fix W=2 build warnings

Fix warnings like follows:

Warning (node_name_chars_strict): Character '_' not recommended in ...

Commit 8654cb8d0371 ("dtc: up

arm64: dts: uniphier: fix W=2 build warnings

Fix warnings like follows:

Warning (node_name_chars_strict): Character '_' not recommended in ...

Commit 8654cb8d0371 ("dtc: update warning settings for new bus and
node/property name checks") says these checks are a bit subjective,
but Rob also says to not add new W=2 warnings.

The exising warnings should be fixed in order to catch new ones
easily.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

show more ...

arm64: dts: uniphier: add efuse node for LD11, LD20, and PXs3

Add efuse node for UniPhier LD11, LD20, and PXs3.
This efuse node is included in soc-glue.

Signed-off-by: Keiji Hay

arm64: dts: uniphier: add efuse node for LD11, LD20, and PXs3

Add efuse node for UniPhier LD11, LD20, and PXs3.
This efuse node is included in soc-glue.

Signed-off-by: Keiji Hayashibara <hayashibara.keiji@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

show more ...

arm64: dts: uniphier: add STDMAC clock to EHCI nodes

Without the STDMAC clock enabled, the USB 2.0 hosts do not work.
This clock must be explicitly listed in the "clocks" property becaus

arm64: dts: uniphier: add STDMAC clock to EHCI nodes

Without the STDMAC clock enabled, the USB 2.0 hosts do not work.
This clock must be explicitly listed in the "clocks" property because
it is independent of the other clocks.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

show more ...

arm64: dts: uniphier: add AIDET nodes

Add UniPhier AIDET (ARM Interrupt Detector) nodes to support
active low interrupts.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socione

arm64: dts: uniphier: add AIDET nodes

Add UniPhier AIDET (ARM Interrupt Detector) nodes to support
active low interrupts.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

show more ...

arm64: dts: uniphier: add reset controller node of analog amplifier

This patch adds reset controller node of analog signal amplifier
core (ADAMV) for UniPhier LD11/LD20 SoCs.

Si

arm64: dts: uniphier: add reset controller node of analog amplifier

This patch adds reset controller node of analog signal amplifier
core (ADAMV) for UniPhier LD11/LD20 SoCs.

Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

show more ...

arm64: dts: uniphier: add Denali NAND controller nodes

Add NAND controller node to LD11 and LD20. Neither of them supports
the CS1 line, so pinctrl is set up for a single CS line.

arm64: dts: uniphier: add Denali NAND controller nodes

Add NAND controller node to LD11 and LD20. Neither of them supports
the CS1 line, so pinctrl is set up for a single CS line.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

show more ...

arm64: dts: uniphier: use #include instead of /include/

To include dt-bindings headers.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

arm64: dts: uniphier: add watchdog node for LD11 and LD20

Add nodes of watchdog timer for UniPhier LD11 and LD20 SoC.
The watchdog timer is included in sysctrl.

Signed-off-by: K

arm64: dts: uniphier: add watchdog node for LD11 and LD20

Add nodes of watchdog timer for UniPhier LD11 and LD20 SoC.
The watchdog timer is included in sysctrl.

Signed-off-by: Keiji Hayashibara <hayashibara.keiji@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

show more ...

arm64: dts: uniphier: use SPDX-License-Identifier

Follow the recent trend for the license description, and fix the wrongly
stated X11 to MIT.

The X11 license text [1] is explici

arm64: dts: uniphier: use SPDX-License-Identifier

Follow the recent trend for the license description, and fix the wrongly
stated X11 to MIT.

The X11 license text [1] is explicitly for the X Consortium and has a
couple of extra clauses. The MIT license text [2] is actually what the
current DT files claim.

[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

show more ...

arm64: dts: uniphier: reserve more memory for LD11/LD20

Reserve enough space below the kernel base.
The assumed address map is:
80000000 - 80ffffff : for IPP
81000000 - 81fff

arm64: dts: uniphier: reserve more memory for LD11/LD20

Reserve enough space below the kernel base.
The assumed address map is:
80000000 - 80ffffff : for IPP
81000000 - 81ffffff : for ARM secure
82000000 - : for Linux

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

show more ...

arm64: dts: uniphier: fix simple-bus unit address format error

Compiling the UniPhier DT files with W=1, DTC warns like follows:

Warning (simple_bus_reg): Node /soc/smpctrl@59800000

arm64: dts: uniphier: fix simple-bus unit address format error

Compiling the UniPhier DT files with W=1, DTC warns like follows:

Warning (simple_bus_reg): Node /soc/smpctrl@59800000 simple-bus unit address format error, expected "59801000"

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

show more ...

arm64: dts: uniphier: Use - instead of @ for DT OPP entries

Compiling the DT file with W=1, DTC warns like follows:

Warning (unit_address_vs_reg): Node /opp_table0/opp@1000000000 ha

arm64: dts: uniphier: Use - instead of @ for DT OPP entries

Compiling the DT file with W=1, DTC warns like follows:

Warning (unit_address_vs_reg): Node /opp_table0/opp@1000000000 has a
unit name, but no reg property

Fix this by replacing '@' with '-' as the OPP nodes will never have a
"reg" property.

Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

show more ...

arm64: dts: uniphier: add cdns, phy-dll-delay-sdclk(-hsmmc) for eMMC

Adjust the PHY parameters for more stable access to the eMMC device.
Set the SDCLK output delay value to 21 (includin

arm64: dts: uniphier: add cdns, phy-dll-delay-sdclk(-hsmmc) for eMMC

Adjust the PHY parameters for more stable access to the eMMC device.
Set the SDCLK output delay value to 21 (including HS200/400 modes).

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

show more ...

arm64: dts: uniphier: add input-delay properties to Cadence eMMC node

Since commit a89c472d8b55 ("mmc: sdhci-cadence: Update PHY delay
configuration"), PHY parameters must be specified b

arm64: dts: uniphier: add input-delay properties to Cadence eMMC node

Since commit a89c472d8b55 ("mmc: sdhci-cadence: Update PHY delay
configuration"), PHY parameters must be specified by DT.

The hard-coded settings have been converted as follows:
- SDHCI_CDNS_PHY_DLY_SD_DEFAULT -> cdns,phy-input-delay-legacy
- SDHCI_CDNS_PHY_DLY_EMMC_SDR -> cdns,phy-input-delay-mmc-highspeed
- SDHCI_CDNS_PHY_DLY_EMMC_DDR -> cdns,phy-input-delay-mmc-ddr

The following have not been moved:
- SDHCI_CDNS_PHY_DLY_SD_HS
this is unneeded in the eMMC configuration
- SDHCI_CDNS_PHY_DLY_EMMC_LEGACY
this is never enabled by the driver as it is covered by
SDHCI_CDNS_PHY_DLY_SD_DEFAULT

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

show more ...

arm64: dts: uniphier: re-order reset deassertion of USB of LD11

Deassert the bit in the System Control block before the MIO block.

Signed-off-by: Masahiro Yamada <yamada.masahiro@so

arm64: dts: uniphier: re-order reset deassertion of USB of LD11

Deassert the bit in the System Control block before the MIO block.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

show more ...

arm64: dts: uniphier: add pinctrl property to eMMC node for LD11/LD20

Now everything is ready to enable this pinctrl.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

arm64: dts: uniphier: fix no unit name warnings

Fix warnings reported when built with W=1:
Node /memory has a reg or ranges property, but no unit name

Signed-off-by: Masahiro

arm64: dts: uniphier: fix no unit name warnings

Fix warnings reported when built with W=1:
Node /memory has a reg or ranges property, but no unit name

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

show more ...

arm64: dts: uniphier: add eMMC controller node for LD11/LD20

Add Cadence's eMMC controller node for LD11/LD20.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>