| /openbmc/u-boot/tools/ |
| H A D | vybridimage.c | 48 uint8_t bit6 = (byte & (1 << 6)) ? 1 : 0; in vybridimage_sw_ecc() local
52 res |= ((bit6 ^ bit5 ^ bit3 ^ bit2) << 0); in vybridimage_sw_ecc()
54 res |= ((bit7 ^ bit6 ^ bit5 ^ bit1 ^ bit0) << 2); in vybridimage_sw_ecc()
56 res |= ((bit6 ^ bit4 ^ bit3 ^ bit2 ^ bit1 ^ bit0) << 4); in vybridimage_sw_ecc()
|
| /openbmc/libpldm/include/libpldm/ |
| H A D | pldm_types.h | 16 uint8_t bit6 : 1; member
43 uint8_t bit6 : 1; member
65 uint8_t bit6 : 1; member
103 uint8_t bit6 : 1; member
|
| /openbmc/linux/Documentation/driver-api/mtd/ |
| H A D | nand_ecc.rst | 45 byte 0: bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 rp0 rp2 rp4 ... rp14
46 byte 1: bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 rp1 rp2 rp4 ... rp14
47 byte 2: bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 rp0 rp3 rp4 ... rp14
48 byte 3: bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 rp1 rp3 rp4 ... rp14
49 byte 4: bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 rp0 rp2 rp5 ... rp14
63 - cp0 is the parity that belongs to all bit0, bit2, bit4, bit6.
70 - cp3 is the parity over bit2, bit3, bit6 and bit7.
72 - cp5 is the parity over bit4, bit5, bit6 and bit7.
160 cp0 = bit6 ^ bit4 ^ bit2 ^ bit0 ^ cp0;
163 cp3 = bit7 ^ bit6 ^ bit3 ^ bit2 ^ cp3
[all …]
|
| /openbmc/linux/include/uapi/linux/ |
| H A D | ioam6.h | 56 bit6:1, member
103 bit6:1, member
|
| /openbmc/u-boot/board/raidsonic/ib62x0/ |
| H A D | kwbimage.cfg | 34 # bit6: 0x0, use recommended falling edge of clk for addr/cmd
54 # bit6-0: TRFC
86 # bit6-4: 0x4, CL=5
98 # bit6: 0, DDR ODT control msb, (disabled)
108 # bit6-4: 0x7, required
|
| /openbmc/u-boot/board/iomega/iconnect/ |
| H A D | kwbimage.cfg | 33 # bit6: 0x0, use recommended falling edge of clk for addr/cmd
53 # bit6-0: TRFC
85 # bit6-4: 0x4, CL=5
97 # bit6: 1, DDR ODT control msb, (disabled)
107 # bit6-4: 0x7, required
|
| /openbmc/u-boot/board/Seagate/nas220/ |
| H A D | kwbimage.cfg | 57 # bit6-0: TRFC
90 # bit6-4: 4, CL=5
103 # bit6: 1, DDR ODT control msb, (disabled)
113 # bit6-4: 111, required
|
| /openbmc/u-boot/board/Marvell/dreamplug/ |
| H A D | kwbimage.cfg | 54 # bit6-0: TRFC
86 # bit6-4: 4, CL=5
98 # bit6: 1, DDR ODT control msb, (disabled)
108 # bit6-4: 111, required
|
| /openbmc/u-boot/board/Marvell/sheevaplug/ |
| H A D | kwbimage.cfg | 53 # bit6-0: TRFC
85 # bit6-4: 4, CL=5
97 # bit6: 1, DDR ODT control msb, (disabled)
107 # bit6-4: 111, required
|
| /openbmc/u-boot/board/Seagate/dockstar/ |
| H A D | kwbimage.cfg | 56 # bit6-0: TRFC
88 # bit6-4: 4, CL=5
100 # bit6: 1, DDR ODT control msb, (disabled)
110 # bit6-4: 111, required
|
| /openbmc/u-boot/board/Marvell/guruplug/ |
| H A D | kwbimage.cfg | 53 # bit6-0: TRFC
85 # bit6-4: 4, CL=5
97 # bit6: 1, DDR ODT control msb, (disabled)
107 # bit6-4: 111, required
|
| /openbmc/u-boot/board/Seagate/goflexhome/ |
| H A D | kwbimage.cfg | 59 # bit6-0: TRFC
91 # bit6-4: 4, CL=5
103 # bit6: 1, DDR ODT control msb, (disabled)
113 # bit6-4: 111, required
|
| /openbmc/u-boot/board/Synology/ds109/ |
| H A D | kwbimage.cfg | 57 # bit6-0: TRFC
89 # bit6-4: 4, CL=5
101 # bit6: 1, DDR ODT control msb, (disabled)
111 # bit6-4: 111, required
|
| /openbmc/u-boot/board/buffalo/lsxl/ |
| H A D | kwbimage-lschl.cfg | 40 # bit6: 0, use recommended falling edge of clk for addr/cmd
67 # bit6-0: 0x23, 35 cycle tRFC
103 # bit6-4: 5, CAS Latency (CL) 5
116 # bit6: 1, ODT control Rtt[1] (Rtt=2, 150 ohm termination)
127 # bit6-4: 0x7 required
|
| H A D | kwbimage-lsxhl.cfg | 40 # bit6: 0, use recommended falling edge of clk for addr/cmd
67 # bit6-0: 0x32, 50 cycle tRFC
103 # bit6-4: 5, CAS Latency (CL) 5
116 # bit6: 0, ODT control Rtt[1] (Rtt=1, 75 ohm termination)
127 # bit6-4: 0x7 required
|
| /openbmc/u-boot/board/LaCie/netspace_v2/ |
| H A D | kwbimage-ns2l.cfg | 53 # bit6-0: TRFC
85 # bit6-4: 4, CL=5
97 # bit6: 1, DDR ODT control msb, enabled
107 # bit6-4: 111, required
|
| H A D | kwbimage.cfg | 53 # bit6-0: TRFC
85 # bit6-4: 4, CL=5
97 # bit6: 1, DDR ODT control msb, enabled
107 # bit6-4: 111, required
|
| H A D | kwbimage-is2.cfg | 53 # bit6-0: TRFC
85 # bit6-4: 4, CL=5
97 # bit6: 1, DDR ODT control msb, enabled
107 # bit6-4: 111, required
|
| /openbmc/u-boot/board/LaCie/net2big_v2/ |
| H A D | kwbimage.cfg | 53 # bit6-0: TRFC
85 # bit6-4: 4, CL=5
97 # bit6: 1, DDR ODT control msb, enabled
107 # bit6-4: 111, required
|
| /openbmc/u-boot/board/cloudengines/pogo_e02/ |
| H A D | kwbimage.cfg | 57 # bit6-0: TRFC
89 # bit6-4: 4, CL=5
101 # bit6: 1, DDR ODT control msb, (disabled)
111 # bit6-4: 111, required
|
| /openbmc/u-boot/board/Marvell/openrd/ |
| H A D | kwbimage.cfg | 53 # bit6-0: TRFC
85 # bit6-4: 4, CL=5
97 # bit6: 1, DDR ODT control msb, (disabled)
107 # bit6-4: 111, required
|
| /openbmc/u-boot/board/d-link/dns325/ |
| H A D | kwbimage.cfg | 38 # bit6: 0, use recommended falling edge of clk for addr/cmd
63 # bit6-0: 0x33, 33 cycle tRFC
95 # bit6-4: 5, CAS Latency (CL) 5
107 # bit6: 1, ODT control Rtt[1] (Rtt=2, 150 ohm termination)
117 # bit6-4: 0x7 required
|
| /openbmc/linux/Documentation/leds/ |
| H A D | leds-mlxcpld.rst | 54 [bit7,bit6,bit5,bit4]:
99 [bit7,bit6,bit5,bit4]:
|
| /openbmc/u-boot/board/keymile/km_arm/ |
| H A D | kwbimage.cfg | 74 # bit6-0: TRFC
109 # bit6: 1, DDR ODT control msb, enabled
119 # bit6-4: 111, required
|
| H A D | kwbimage-memphis.cfg | 77 # bit6-0: TRFC
112 # bit6: 0, DDR ODT control msb disabled
122 # bit6-4: 111, required
|