1# SPDX-License-Identifier: GPL-2.0+
2#
3# (C) Copyright 2009
4# Marvell Semiconductor <www.marvell.com>
5# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
6# Refer to doc/README.kwbimage for more details about how-to
7# configure and create kirkwood boot images.
8#
9
10# Boot Media configurations
11BOOT_FROM	nand
12NAND_ECC_MODE	default
13NAND_PAGE_SIZE	0x0800
14
15# SOC registers configuration using bootrom header extension
16# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
17
18# Configure RGMII-0 interface pad voltage to 1.8V
19DATA 0xFFD100e0 0x1b1b1b9b
20
21#Dram initalization for SINGLE x16 CL=5 @ 400MHz
22DATA 0xFFD01400 0x43000c30	# DDR Configuration register
23# bit13-0:  0xc30 (3120 DDR2 clks refresh rate)
24# bit23-14: zero
25# bit24: 1= enable exit self refresh mode on DDR access
26# bit25: 1 required
27# bit29-26: zero
28# bit31-30: 01
29
30DATA 0xFFD01404 0x37543000	# DDR Controller Control Low
31# bit 4:    0=addr/cmd in smame cycle
32# bit 5:    0=clk is driven during self refresh, we don't care for APX
33# bit 6:    0=use recommended falling edge of clk for addr/cmd
34# bit14:    0=input buffer always powered up
35# bit18:    1=cpu lock transaction enabled
36# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
37# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
38# bit30-28: 3 required
39# bit31:    0=no additional STARTBURST delay
40
41DATA 0xFFD01408 0x22125451	# DDR Timing (Low) (active cycles value +1)
42# bit3-0:   TRAS lsbs
43# bit7-4:   TRCD
44# bit11- 8: TRP
45# bit15-12: TWR
46# bit19-16: TWTR
47# bit20:    TRAS msb
48# bit23-21: 0x0
49# bit27-24: TRRD
50# bit31-28: TRTP
51
52DATA 0xFFD0140C 0x00000a33	#  DDR Timing (High)
53# bit6-0:   TRFC
54# bit8-7:   TR2R
55# bit10-9:  TR2W
56# bit12-11: TW2W
57# bit31-13: zero required
58
59DATA 0xFFD01410 0x000000cc	#  DDR Address Control
60# bit1-0:   00, Cs0width=x8
61# bit3-2:   11, Cs0size=1Gb
62# bit5-4:   00, Cs1width=x8
63# bit7-6:   11, Cs1size=1Gb
64# bit9-8:   00, Cs2width=nonexistent
65# bit11-10: 00, Cs2size =nonexistent
66# bit13-12: 00, Cs3width=nonexistent
67# bit15-14: 00, Cs3size =nonexistent
68# bit16:    0,  Cs0AddrSel
69# bit17:    0,  Cs1AddrSel
70# bit18:    0,  Cs2AddrSel
71# bit19:    0,  Cs3AddrSel
72# bit31-20: 0 required
73
74DATA 0xFFD01414 0x00000000	#  DDR Open Pages Control
75# bit0:    0,  OpenPage enabled
76# bit31-1: 0 required
77
78DATA 0xFFD01418 0x00000000	#  DDR Operation
79# bit3-0:   0x0, DDR cmd
80# bit31-4:  0 required
81
82DATA 0xFFD0141C 0x00000C52	#  DDR Mode
83# bit2-0:   2, BurstLen=2 required
84# bit3:     0, BurstType=0 required
85# bit6-4:   4, CL=5
86# bit7:     0, TestMode=0 normal
87# bit8:     0, DLL reset=0 normal
88# bit11-9:  6, auto-precharge write recovery ????????????
89# bit12:    0, PD must be zero
90# bit31-13: 0 required
91
92DATA 0xFFD01420 0x00000040	#  DDR Extended Mode
93# bit0:    0,  DDR DLL enabled
94# bit1:    0,  DDR drive strenght normal
95# bit2:    0,  DDR ODT control lsd (disabled)
96# bit5-3:  000, required
97# bit6:    1,  DDR ODT control msb, (disabled)
98# bit9-7:  000, required
99# bit10:   0,  differential DQS enabled
100# bit11:   0, required
101# bit12:   0, DDR output buffer enabled
102# bit31-13: 0 required
103
104DATA 0xFFD01424 0x0000F17F	#  DDR Controller Control High
105# bit2-0:  111, required
106# bit3  :  1  , MBUS Burst Chop disabled
107# bit6-4:  111, required
108# bit7  :  0
109# bit8  :  1  , add writepath sample stage, must be 1 for DDR freq >= 300MHz
110# bit9  :  0  , no half clock cycle addition to dataout
111# bit10 :  0  , 1/4 clock cycle skew enabled for addr/ctl signals
112# bit11 :  0  , 1/4 clock cycle skew disabled for write mesh
113# bit15-12: 1111 required
114# bit31-16: 0    required
115
116DATA 0xFFD01428 0x00085520	# DDR2 ODT Read Timing (default values)
117DATA 0xFFD0147C 0x00008552	# DDR2 ODT Write Timing (default values)
118
119DATA 0xFFD01500 0x00000000	# CS[0]n Base address to 0x0
120DATA 0xFFD01504 0x0FFFFFF1	# CS[0]n Size
121# bit0:    1,  Window enabled
122# bit1:    0,  Write Protect disabled
123# bit3-2:  00, CS0 hit selected
124# bit23-4: ones, required
125# bit31-24: 0x0F, Size (i.e. 256MB)
126
127DATA 0xFFD01508 0x10000000	# CS[1]n Base address to 256Mb
128DATA 0xFFD0150C 0x0FFFFFF5	# CS[1]n Size 256Mb Window enabled for CS1
129
130DATA 0xFFD01514 0x00000000	# CS[2]n Size, window disabled
131DATA 0xFFD0151C 0x00000000	# CS[3]n Size, window disabled
132
133DATA 0xFFD01494 0x00030000	#  DDR ODT Control (Low)
134DATA 0xFFD01498 0x00000000	#  DDR ODT Control (High)
135# bit1-0:  00, ODT0 controlled by ODT Control (low) register above
136# bit3-2:  01, ODT1 active NEVER!
137# bit31-4: zero, required
138
139DATA 0xFFD0149C 0x0000E803	# CPU ODT Control
140DATA 0xFFD01480 0x00000001	# DDR Initialization Control
141#bit0=1, enable DDR init upon this register write
142
143# End of Header extension
144DATA 0x0 0x0
145