| /openbmc/linux/Documentation/networking/ |
| H A D | packet_mmap.rst | 43 at high speeds (this is relative to the cpu speed), you should check if the
|
| /openbmc/linux/Documentation/scsi/ |
| H A D | ChangeLog.sym53c8xx | 343 - Measure the PCI clock speed and do not attach controllers if
|
| /openbmc/linux/Documentation/admin-guide/ |
| H A D | md.rst | 714 This shows the current actual speed, in K/sec, of the current
|
| /openbmc/openbmc/poky/documentation/ref-manual/ |
| H A D | structure.rst | 387 caches the results in ``build/tmp/cache/`` to speed up future builds.
|
| /openbmc/linux/Documentation/admin-guide/hw-vuln/ |
| H A D | spectre.rst | 17 high performance processors, since most modern high speed processors
|
| /openbmc/linux/include/linux/ |
| H A D | pci.h | 1342 enum pci_bus_speed *speed,
|
| /openbmc/linux/drivers/net/ethernet/neterion/ |
| H A D | s2io.c | 5278 (cmd->base.speed != SPEED_10000) || in s2io_ethtool_set_link_ksettings()
5317 cmd->base.speed = SPEED_10000; in s2io_ethtool_get_link_ksettings()
5320 cmd->base.speed = SPEED_UNKNOWN; in s2io_ethtool_get_link_ksettings()
|
| /openbmc/linux/arch/arm/boot/dts/nvidia/ |
| H A D | tegra30-ouya.dts | 2023 max-speed = <4000000>;
4614 gpio-fan,speed-map = <0 0
|
| H A D | tegra30-beaver.dts | 1721 nvidia,high-speed-mode = <TEGRA_PIN_DISABLE>;
|
| /openbmc/openbmc/poky/bitbake/doc/bitbake-user-manual/ |
| H A D | bitbake-user-manual-ref-variables.rst | 593 - *speed* --- executes tasks first that have more tasks depending on
594 them. The "speed" option is the default.
|
| H A D | bitbake-user-manual-execution.rst | 396 It is worth noting that you can greatly speed up the build time by
|
| /openbmc/linux/arch/arm64/boot/dts/qcom/ |
| H A D | sc7180.dtsi | 2987 maximum-speed = "super-speed";
|
| /openbmc/linux/drivers/media/usb/cx231xx/ |
| H A D | cx231xx-avcore.c | 2546 if (dev->udev->speed == USB_SPEED_HIGH) { in cx231xx_initialize_stream_xfer()
|
| /openbmc/linux/drivers/net/ethernet/engleder/ |
| H A D | tsnep_main.c | 187 switch (adapter->phydev->speed) { in tsnep_set_link_mode()
|
| /openbmc/linux/drivers/net/ethernet/broadcom/ |
| H A D | bcmsysport.c | 1436 switch (phydev->speed) { in bcm_sysport_adj_link()
|
| /openbmc/linux/drivers/scsi/cxgbi/cxgb4i/ |
| H A D | cxgb4i.c | 1869 linkspeed = ((struct port_info *)netdev_priv(ndev))->link_cfg.speed; in init_act_open()
|
| /openbmc/linux/drivers/scsi/lpfc/ |
| H A D | lpfc_hw.h | 1193 uint16_t speed; member
|
| /openbmc/linux/arch/arm64/boot/dts/nvidia/ |
| H A D | tegra210-smaug.dts | 1328 max-speed = <4000000>;
|
| /openbmc/linux/arch/arm64/boot/dts/mediatek/ |
| H A D | mt8186.dtsi | 1716 nvmem-cell-names = "speed-bin";
|
| /openbmc/linux/drivers/net/ethernet/intel/ixgbe/ |
| H A D | ixgbe_type.h | 3290 enum ixgbe_bus_speed speed; member
|
| /openbmc/linux/arch/arm64/boot/dts/rockchip/ |
| H A D | rk356x.dtsi | 992 max-link-speed = <2>;
|
| /openbmc/linux/arch/arm64/boot/dts/amlogic/ |
| H A D | meson-g12-common.dtsi | 1713 max-speed = <100>;
|
| /openbmc/linux/drivers/scsi/aic7xxx/ |
| H A D | aic79xx_core.c | 6939 const char *speed; in ahd_controller_info() local
6946 speed = "Ultra320 "; in ahd_controller_info()
6953 speed, type, ahd->channel, ahd->our_id); in ahd_controller_info()
|
| /openbmc/linux/drivers/scsi/bfa/ |
| H A D | bfa_fcs_lport.c | 2729 bfa_fcs_fdmi_convert_speed(pport_attr.speed)); in bfa_fcs_fdmi_get_portattr()
5837 port_speed = port_attr.speed; in bfa_fcs_lport_get_rport_max_speed()
|
| /openbmc/qemu/ |
| H A D | qemu-options.hx | 2706 " [,asset=str][,part=str][,max-speed=%d][,current-speed=%d]\n"
2714 " [,asset=str][,part=str][,speed=%d]\n"
2780 …ype=17[,loc_pfx=str][,bank=str][,manufacturer=str][,serial=str][,asset=str][,part=str][,speed=%d]``
4852 determinism; however, note that in icount mode the speed of the
4872 then the virtual cpu speed will be automatically adjusted to keep
4882 default speed unless ``sleep=on`` is specified. With
|