Revert "ixgbe: Manual AN-37 for troublesome link partners for X550 SFI"

[ Upstream commit b35b1c0b4e166a427395deaf61e3140495dfcb89 ]

This reverts commit 565736048bd5f9888990569993c6b6bfdf6dcb6d.

A

Revert "ixgbe: Manual AN-37 for troublesome link partners for X550 SFI"

[ Upstream commit b35b1c0b4e166a427395deaf61e3140495dfcb89 ]

This reverts commit 565736048bd5f9888990569993c6b6bfdf6dcb6d.

According to the commit, it implements a manual AN-37 for some
"troublesome" Juniper MX5 switches. This appears to be a workaround for a
particular switch.

It has been reported that this causes a severe breakage for other switches,
including a Cisco 3560CX-12PD-S.

The code appears to be a workaround for a specific switch which fails to
link in SFI mode. It expects to see AN-37 auto negotiation in order to
link. The Cisco switch is not expecting AN-37 auto negotiation. When the
device starts the manual AN-37, the Cisco switch decides that the port is
confused and stops attempting to link with it. This persists until a power
cycle. A simple driver unload and reload does not resolve the issue, even
if loading with a version of the driver which lacks this workaround.

The authors of the workaround commit have not responded with
clarifications, and the result of the workaround is complete failure to
connect with other switches.

This appears to be a case where the driver can either "correctly" link with
the Juniper MX5 switch, at the cost of bricking the link with the Cisco
switch, or it can behave properly for the Cisco switch, but fail to link
with the Junipir MX5 switch. I do not know enough about the standards
involved to clearly determine whether either switch is at fault or behaving
incorrectly. Nor do I know whether there exists some alternative fix which
corrects behavior with both switches.

Revert the workaround for the Juniper switch.

Fixes: 565736048bd5 ("ixgbe: Manual AN-37 for troublesome link partners for X550 SFI")
Link: https://lore.kernel.org/netdev/cbe874db-9ac9-42b8-afa0-88ea910e1e99@intel.com/T/
Link: https://forum.proxmox.com/threads/intel-x553-sfp-ixgbe-no-go-on-pve8.135129/#post-612291
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Jeff Daly <jeffd@silicom-usa.com>
Cc: kernel.org-fo5k2w@ycharbi.fr
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240520-net-2024-05-20-revert-silicom-switch-workaround-v1-1-50f80f261c94@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

Revert "ixgbe: Manual AN-37 for troublesome link partners for X550 SFI"

[ Upstream commit b35b1c0b4e166a427395deaf61e3140495dfcb89 ]

This reverts commit 565736048bd5f9888990569993c6b6bfdf6dcb6d.

A

Revert "ixgbe: Manual AN-37 for troublesome link partners for X550 SFI"

[ Upstream commit b35b1c0b4e166a427395deaf61e3140495dfcb89 ]

This reverts commit 565736048bd5f9888990569993c6b6bfdf6dcb6d.

According to the commit, it implements a manual AN-37 for some
"troublesome" Juniper MX5 switches. This appears to be a workaround for a
particular switch.

It has been reported that this causes a severe breakage for other switches,
including a Cisco 3560CX-12PD-S.

The code appears to be a workaround for a specific switch which fails to
link in SFI mode. It expects to see AN-37 auto negotiation in order to
link. The Cisco switch is not expecting AN-37 auto negotiation. When the
device starts the manual AN-37, the Cisco switch decides that the port is
confused and stops attempting to link with it. This persists until a power
cycle. A simple driver unload and reload does not resolve the issue, even
if loading with a version of the driver which lacks this workaround.

The authors of the workaround commit have not responded with
clarifications, and the result of the workaround is complete failure to
connect with other switches.

This appears to be a case where the driver can either "correctly" link with
the Juniper MX5 switch, at the cost of bricking the link with the Cisco
switch, or it can behave properly for the Cisco switch, but fail to link
with the Junipir MX5 switch. I do not know enough about the standards
involved to clearly determine whether either switch is at fault or behaving
incorrectly. Nor do I know whether there exists some alternative fix which
corrects behavior with both switches.

Revert the workaround for the Juniper switch.

Fixes: 565736048bd5 ("ixgbe: Manual AN-37 for troublesome link partners for X550 SFI")
Link: https://lore.kernel.org/netdev/cbe874db-9ac9-42b8-afa0-88ea910e1e99@intel.com/T/
Link: https://forum.proxmox.com/threads/intel-x553-sfp-ixgbe-no-go-on-pve8.135129/#post-612291
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Jeff Daly <jeffd@silicom-usa.com>
Cc: kernel.org-fo5k2w@ycharbi.fr
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240520-net-2024-05-20-revert-silicom-switch-workaround-v1-1-50f80f261c94@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

Revert "ixgbe: Manual AN-37 for troublesome link partners for X550 SFI"

[ Upstream commit b35b1c0b4e166a427395deaf61e3140495dfcb89 ]

This reverts commit 565736048bd5f9888990569993c6b6bfdf6dcb6d.

A

Revert "ixgbe: Manual AN-37 for troublesome link partners for X550 SFI"

[ Upstream commit b35b1c0b4e166a427395deaf61e3140495dfcb89 ]

This reverts commit 565736048bd5f9888990569993c6b6bfdf6dcb6d.

According to the commit, it implements a manual AN-37 for some
"troublesome" Juniper MX5 switches. This appears to be a workaround for a
particular switch.

It has been reported that this causes a severe breakage for other switches,
including a Cisco 3560CX-12PD-S.

The code appears to be a workaround for a specific switch which fails to
link in SFI mode. It expects to see AN-37 auto negotiation in order to
link. The Cisco switch is not expecting AN-37 auto negotiation. When the
device starts the manual AN-37, the Cisco switch decides that the port is
confused and stops attempting to link with it. This persists until a power
cycle. A simple driver unload and reload does not resolve the issue, even
if loading with a version of the driver which lacks this workaround.

The authors of the workaround commit have not responded with
clarifications, and the result of the workaround is complete failure to
connect with other switches.

This appears to be a case where the driver can either "correctly" link with
the Juniper MX5 switch, at the cost of bricking the link with the Cisco
switch, or it can behave properly for the Cisco switch, but fail to link
with the Junipir MX5 switch. I do not know enough about the standards
involved to clearly determine whether either switch is at fault or behaving
incorrectly. Nor do I know whether there exists some alternative fix which
corrects behavior with both switches.

Revert the workaround for the Juniper switch.

Fixes: 565736048bd5 ("ixgbe: Manual AN-37 for troublesome link partners for X550 SFI")
Link: https://lore.kernel.org/netdev/cbe874db-9ac9-42b8-afa0-88ea910e1e99@intel.com/T/
Link: https://forum.proxmox.com/threads/intel-x553-sfp-ixgbe-no-go-on-pve8.135129/#post-612291
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Jeff Daly <jeffd@silicom-usa.com>
Cc: kernel.org-fo5k2w@ycharbi.fr
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240520-net-2024-05-20-revert-silicom-switch-workaround-v1-1-50f80f261c94@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

Revert "ixgbe: Manual AN-37 for troublesome link partners for X550 SFI"

[ Upstream commit b35b1c0b4e166a427395deaf61e3140495dfcb89 ]

This reverts commit 565736048bd5f9888990569993c6b6bfdf6dcb6d.

A

Revert "ixgbe: Manual AN-37 for troublesome link partners for X550 SFI"

[ Upstream commit b35b1c0b4e166a427395deaf61e3140495dfcb89 ]

This reverts commit 565736048bd5f9888990569993c6b6bfdf6dcb6d.

According to the commit, it implements a manual AN-37 for some
"troublesome" Juniper MX5 switches. This appears to be a workaround for a
particular switch.

It has been reported that this causes a severe breakage for other switches,
including a Cisco 3560CX-12PD-S.

The code appears to be a workaround for a specific switch which fails to
link in SFI mode. It expects to see AN-37 auto negotiation in order to
link. The Cisco switch is not expecting AN-37 auto negotiation. When the
device starts the manual AN-37, the Cisco switch decides that the port is
confused and stops attempting to link with it. This persists until a power
cycle. A simple driver unload and reload does not resolve the issue, even
if loading with a version of the driver which lacks this workaround.

The authors of the workaround commit have not responded with
clarifications, and the result of the workaround is complete failure to
connect with other switches.

This appears to be a case where the driver can either "correctly" link with
the Juniper MX5 switch, at the cost of bricking the link with the Cisco
switch, or it can behave properly for the Cisco switch, but fail to link
with the Junipir MX5 switch. I do not know enough about the standards
involved to clearly determine whether either switch is at fault or behaving
incorrectly. Nor do I know whether there exists some alternative fix which
corrects behavior with both switches.

Revert the workaround for the Juniper switch.

Fixes: 565736048bd5 ("ixgbe: Manual AN-37 for troublesome link partners for X550 SFI")
Link: https://lore.kernel.org/netdev/cbe874db-9ac9-42b8-afa0-88ea910e1e99@intel.com/T/
Link: https://forum.proxmox.com/threads/intel-x553-sfp-ixgbe-no-go-on-pve8.135129/#post-612291
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Jeff Daly <jeffd@silicom-usa.com>
Cc: kernel.org-fo5k2w@ycharbi.fr
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240520-net-2024-05-20-revert-silicom-switch-workaround-v1-1-50f80f261c94@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

Revert "ixgbe: Manual AN-37 for troublesome link partners for X550 SFI"

[ Upstream commit b35b1c0b4e166a427395deaf61e3140495dfcb89 ]

This reverts commit 565736048bd5f9888990569993c6b6bfdf6dcb6d.

A

Revert "ixgbe: Manual AN-37 for troublesome link partners for X550 SFI"

[ Upstream commit b35b1c0b4e166a427395deaf61e3140495dfcb89 ]

This reverts commit 565736048bd5f9888990569993c6b6bfdf6dcb6d.

According to the commit, it implements a manual AN-37 for some
"troublesome" Juniper MX5 switches. This appears to be a workaround for a
particular switch.

It has been reported that this causes a severe breakage for other switches,
including a Cisco 3560CX-12PD-S.

The code appears to be a workaround for a specific switch which fails to
link in SFI mode. It expects to see AN-37 auto negotiation in order to
link. The Cisco switch is not expecting AN-37 auto negotiation. When the
device starts the manual AN-37, the Cisco switch decides that the port is
confused and stops attempting to link with it. This persists until a power
cycle. A simple driver unload and reload does not resolve the issue, even
if loading with a version of the driver which lacks this workaround.

The authors of the workaround commit have not responded with
clarifications, and the result of the workaround is complete failure to
connect with other switches.

This appears to be a case where the driver can either "correctly" link with
the Juniper MX5 switch, at the cost of bricking the link with the Cisco
switch, or it can behave properly for the Cisco switch, but fail to link
with the Junipir MX5 switch. I do not know enough about the standards
involved to clearly determine whether either switch is at fault or behaving
incorrectly. Nor do I know whether there exists some alternative fix which
corrects behavior with both switches.

Revert the workaround for the Juniper switch.

Fixes: 565736048bd5 ("ixgbe: Manual AN-37 for troublesome link partners for X550 SFI")
Link: https://lore.kernel.org/netdev/cbe874db-9ac9-42b8-afa0-88ea910e1e99@intel.com/T/
Link: https://forum.proxmox.com/threads/intel-x553-sfp-ixgbe-no-go-on-pve8.135129/#post-612291
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Jeff Daly <jeffd@silicom-usa.com>
Cc: kernel.org-fo5k2w@ycharbi.fr
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240520-net-2024-05-20-revert-silicom-switch-workaround-v1-1-50f80f261c94@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

Revert "ixgbe: Manual AN-37 for troublesome link partners for X550 SFI"

[ Upstream commit b35b1c0b4e166a427395deaf61e3140495dfcb89 ]

This reverts commit 565736048bd5f9888990569993c6b6bfdf6dcb6d.

A

Revert "ixgbe: Manual AN-37 for troublesome link partners for X550 SFI"

[ Upstream commit b35b1c0b4e166a427395deaf61e3140495dfcb89 ]

This reverts commit 565736048bd5f9888990569993c6b6bfdf6dcb6d.

According to the commit, it implements a manual AN-37 for some
"troublesome" Juniper MX5 switches. This appears to be a workaround for a
particular switch.

It has been reported that this causes a severe breakage for other switches,
including a Cisco 3560CX-12PD-S.

The code appears to be a workaround for a specific switch which fails to
link in SFI mode. It expects to see AN-37 auto negotiation in order to
link. The Cisco switch is not expecting AN-37 auto negotiation. When the
device starts the manual AN-37, the Cisco switch decides that the port is
confused and stops attempting to link with it. This persists until a power
cycle. A simple driver unload and reload does not resolve the issue, even
if loading with a version of the driver which lacks this workaround.

The authors of the workaround commit have not responded with
clarifications, and the result of the workaround is complete failure to
connect with other switches.

This appears to be a case where the driver can either "correctly" link with
the Juniper MX5 switch, at the cost of bricking the link with the Cisco
switch, or it can behave properly for the Cisco switch, but fail to link
with the Junipir MX5 switch. I do not know enough about the standards
involved to clearly determine whether either switch is at fault or behaving
incorrectly. Nor do I know whether there exists some alternative fix which
corrects behavior with both switches.

Revert the workaround for the Juniper switch.

Fixes: 565736048bd5 ("ixgbe: Manual AN-37 for troublesome link partners for X550 SFI")
Link: https://lore.kernel.org/netdev/cbe874db-9ac9-42b8-afa0-88ea910e1e99@intel.com/T/
Link: https://forum.proxmox.com/threads/intel-x553-sfp-ixgbe-no-go-on-pve8.135129/#post-612291
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Jeff Daly <jeffd@silicom-usa.com>
Cc: kernel.org-fo5k2w@ycharbi.fr
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240520-net-2024-05-20-revert-silicom-switch-workaround-v1-1-50f80f261c94@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

Revert "ixgbe: Manual AN-37 for troublesome link partners for X550 SFI"

[ Upstream commit b35b1c0b4e166a427395deaf61e3140495dfcb89 ]

This reverts commit 565736048bd5f9888990569993c6b6bfdf6dcb6d.

A

Revert "ixgbe: Manual AN-37 for troublesome link partners for X550 SFI"

[ Upstream commit b35b1c0b4e166a427395deaf61e3140495dfcb89 ]

This reverts commit 565736048bd5f9888990569993c6b6bfdf6dcb6d.

According to the commit, it implements a manual AN-37 for some
"troublesome" Juniper MX5 switches. This appears to be a workaround for a
particular switch.

It has been reported that this causes a severe breakage for other switches,
including a Cisco 3560CX-12PD-S.

The code appears to be a workaround for a specific switch which fails to
link in SFI mode. It expects to see AN-37 auto negotiation in order to
link. The Cisco switch is not expecting AN-37 auto negotiation. When the
device starts the manual AN-37, the Cisco switch decides that the port is
confused and stops attempting to link with it. This persists until a power
cycle. A simple driver unload and reload does not resolve the issue, even
if loading with a version of the driver which lacks this workaround.

The authors of the workaround commit have not responded with
clarifications, and the result of the workaround is complete failure to
connect with other switches.

This appears to be a case where the driver can either "correctly" link with
the Juniper MX5 switch, at the cost of bricking the link with the Cisco
switch, or it can behave properly for the Cisco switch, but fail to link
with the Junipir MX5 switch. I do not know enough about the standards
involved to clearly determine whether either switch is at fault or behaving
incorrectly. Nor do I know whether there exists some alternative fix which
corrects behavior with both switches.

Revert the workaround for the Juniper switch.

Fixes: 565736048bd5 ("ixgbe: Manual AN-37 for troublesome link partners for X550 SFI")
Link: https://lore.kernel.org/netdev/cbe874db-9ac9-42b8-afa0-88ea910e1e99@intel.com/T/
Link: https://forum.proxmox.com/threads/intel-x553-sfp-ixgbe-no-go-on-pve8.135129/#post-612291
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Jeff Daly <jeffd@silicom-usa.com>
Cc: kernel.org-fo5k2w@ycharbi.fr
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240520-net-2024-05-20-revert-silicom-switch-workaround-v1-1-50f80f261c94@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

ixgbe: Refactor overtemp event handling

[ Upstream commit 6c1b4af8c1b20c70dde01e58381685d6a4a1d2c8 ]

Currently ixgbe driver is notified of overheating events
via internal IXGBE_ERR_OVERTEMP error c

ixgbe: Refactor overtemp event handling

[ Upstream commit 6c1b4af8c1b20c70dde01e58381685d6a4a1d2c8 ]

Currently ixgbe driver is notified of overheating events
via internal IXGBE_ERR_OVERTEMP error code.

Change the approach for handle_lasi() to use freshly introduced
is_overtemp function parameter which set when such event occurs.
Change check_overtemp() to bool and return true if overtemp
event occurs.

Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

ixgbe: Refactor returning internal error codes

[ Upstream commit 5795f533f30a80aa0473652876296ebc9129e33a ]

Change returning codes to the kernel ones instead of
the internal ones for the entire ixg

ixgbe: Refactor returning internal error codes

[ Upstream commit 5795f533f30a80aa0473652876296ebc9129e33a ]

Change returning codes to the kernel ones instead of
the internal ones for the entire ixgbe driver.

Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stable-dep-of: bbc404d20d1b ("ixgbe: Fix an error handling path in ixgbe_read_iosf_sb_reg_x550()")
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

ixgbe: Manual AN-37 for troublesome link partners for X550 SFI

Some (Juniper MX5) SFP link partners exhibit a disinclination to
autonegotiate with X550 configured in SFI mode. This patch enables
a

ixgbe: Manual AN-37 for troublesome link partners for X550 SFI

Some (Juniper MX5) SFP link partners exhibit a disinclination to
autonegotiate with X550 configured in SFI mode. This patch enables
a manual AN-37 restart to work around the problem.

Signed-off-by: Jeff Daly <jeffd@silicom-usa.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

show more ...

drivers, ixgbe: export vf statistics

This change retrieves network metrics for virtual functions from the
device and exports them via the iproute2 interface.

The code for retrieving the statistics

drivers, ixgbe: export vf statistics

This change retrieves network metrics for virtual functions from the
device and exports them via the iproute2 interface.

The code for retrieving the statistics from the device is taken from the
out-of-tree driver. The feature was introduced with version 2.0.75.7,
so the diff between this version and the previous version 2.0.72.4 was
used to identify required changes. The export via ethtool is omitted in
favor of using the standard ndo_get_vf_stats interface.

Per-VF statistics can now be printed, for instance, via

ip --statistics link show dev eth0

Signed-off-by: Maximilian Heyne <mheyne@amazon.de>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

show more ...

ixgbe: Remove non-inclusive language

Remove non-inclusive language from the driver.

Additionally correct the duplication "from from"
reported by checkpatch after the changes above.

Signed-off-by:

ixgbe: Remove non-inclusive language

Remove non-inclusive language from the driver.

Additionally correct the duplication "from from"
reported by checkpatch after the changes above.

Signed-off-by: Piotr Skajewski <piotrx.skajewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

show more ...

net: intel: Remove unused function pointer typedef ixgbe_mc_addr_itr

Remove the 'ixgbe_mc_addr_itr' typedef as it is not used.

Signed-off-by: Chen Lin <chen.lin5@zte.com.cn>
Tested-by: Dave Switzer

net: intel: Remove unused function pointer typedef ixgbe_mc_addr_itr

Remove the 'ixgbe_mc_addr_itr' typedef as it is not used.

Signed-off-by: Chen Lin <chen.lin5@zte.com.cn>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

show more ...

ixgbe: Support external GBE SerDes PHY BCM54616s

The Broadcom PHY is used in switches, so add the ID, and hook it up.

This upstreams the Linux kernel patch from the network operating system
SONiC f

ixgbe: Support external GBE SerDes PHY BCM54616s

The Broadcom PHY is used in switches, so add the ID, and hook it up.

This upstreams the Linux kernel patch from the network operating system
SONiC from February 2020 [1].

[1]: https://github.com/Azure/sonic-linux-kernel/pull/122

Signed-off-by: Jostar Yang <jostar_yang@accton.com>
Signed-off-by: Guohan Lu <lguohan@gmail.com>
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

show more ...

ixgbe: implement support for SDP/PPS output on X550 hardware

Similar to the X540 hardware, enable support for generating a 1pps
output signal on SDP0.

This support is slightly different to the X540

ixgbe: implement support for SDP/PPS output on X550 hardware

Similar to the X540 hardware, enable support for generating a 1pps
output signal on SDP0.

This support is slightly different to the X540 hardware, because of the
register layout changes. First, the system time register is now
represented in 'cycles' and 'billions of cycles'. Second, we need to
also program the TSSDP register, as well as the ESDP register. Third,
the clock output uses only FREQOUT, instead of a full 64bit value for
the output clock period. Finally, we have to use the ST0 bit instead of
the SYNCLK bit in the TSAUXC register.

This support should work even for the hardware with a higher frequency
clock, as it carefully takes into account the multiply and shift of the
cycle counter used.

We also set the pps configuration to 1, since we now support generating
a pulse per second output.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

show more ...

ixgbe: firmware recovery mode

Add check for FW NVM recovery mode during driver initialization and
service task. If in recovery mode, log message and unregister device

Signed-off-by: Sebastian Basie

ixgbe: firmware recovery mode

Add check for FW NVM recovery mode during driver initialization and
service task. If in recovery mode, log message and unregister device

Signed-off-by: Sebastian Basierski <sebastianx.basierski@intel.com>
Tested-by: Don Buchholz <donald.buchholz@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

show more ...

ixgbe: fix driver behaviour after issuing VFLR

Since VFLR doesn't clear VFMBMEM (VF Mailbox Memory)
and is not re-enabling queues correctly we should fix
this behavior.

Signed-off-by: Sebastian Bas

ixgbe: fix driver behaviour after issuing VFLR

Since VFLR doesn't clear VFMBMEM (VF Mailbox Memory)
and is not re-enabling queues correctly we should fix
this behavior.

Signed-off-by: Sebastian Basierski <sebastianx.basierski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

show more ...

ixgbe: Fix bit definitions and add support for testing for ipsec support

This patch addresses two issues. First it adds the correct bit definitions
for the SECTXSTAT and SECRXSTAT registers. Then it

ixgbe: Fix bit definitions and add support for testing for ipsec support

This patch addresses two issues. First it adds the correct bit definitions
for the SECTXSTAT and SECRXSTAT registers. Then it makes use of those
definitions to test for if IPsec has been disabled on the part and if so we
do not enable it.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Reported-by: Andre Tomt <andre@tomt.net>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

show more ...

net: intel: Cleanup the copyright/license headers

After many years of having a ~30 line copyright and license header to our
source files, we are finally able to reduce that to one line with the
adve

net: intel: Cleanup the copyright/license headers

After many years of having a ~30 line copyright and license header to our
source files, we are finally able to reduce that to one line with the
advent of the SPDX identifier.

Also caught a few files missing the SPDX license identifier, so fixed
them up.

Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

intel: add SPDX identifiers to all the Intel drivers

Add the SPDX identifiers to all the Intel wired LAN driver files, as
outlined in Documentation/process/license-rules.rst.

Signed-off-by: Jeff Ki

intel: add SPDX identifiers to all the Intel drivers

Add the SPDX identifiers to all the Intel wired LAN driver files, as
outlined in Documentation/process/license-rules.rst.

Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

ixgbe: process the Tx ipsec offload

If the skb has a security association referenced in the skb, then
set up the Tx descriptor with the ipsec offload bits. While we're
here, we fix an oddly named f

ixgbe: process the Tx ipsec offload

If the skb has a security association referenced in the skb, then
set up the Tx descriptor with the ipsec offload bits. While we're
here, we fix an oddly named field in the context descriptor struct.

Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

show more ...

ixgbe: clean up ipsec defines

Clean up the ipsec/macsec descriptor bit definitions to match the rest
of the defines and file organization. Also recognise the bit-definition
overlap in the error mas

ixgbe: clean up ipsec defines

Clean up the ipsec/macsec descriptor bit definitions to match the rest
of the defines and file organization. Also recognise the bit-definition
overlap in the error mask macro.

Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

show more ...

ixgbe: extend firmware version support

Extend FW version reporting by displaying information from the iSCSI
or OEM block in the EEPROM.

This will allow us to more accurately identify the FW.

Signe

ixgbe: extend firmware version support

Extend FW version reporting by displaying information from the iSCSI
or OEM block in the EEPROM.

This will allow us to more accurately identify the FW.

Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

show more ...

ixgbe: Update NW_MNG_IF_SEL support for X553

The MAC register NW_MNG_IF_SEL fields have been redefined for
X553. These changes impact the iXFI driver code flow. Since iXFI is
only supported in X552,

ixgbe: Update NW_MNG_IF_SEL support for X553

The MAC register NW_MNG_IF_SEL fields have been redefined for
X553. These changes impact the iXFI driver code flow. Since iXFI is
only supported in X552, add MAC checks for iXFI flows.

Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

show more ...

ixgbe: Add 1000Base-T device based on X550EM_X MAC

Add support for new 1000Base-T device based on X550EM_X MAC
type. All PHY operations are disabled as the PHY is controlled
by FW.

Signed-off-by: P

ixgbe: Add 1000Base-T device based on X550EM_X MAC

Add support for new 1000Base-T device based on X550EM_X MAC
type. All PHY operations are disabled as the PHY is controlled
by FW.

Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

show more ...