| /openbmc/linux/Documentation/devicetree/bindings/sound/ |
| H A D | audio-iio-aux.yaml | 42 minimum sound control value correspond to the maximum IIO channel
43 raw value and the maximum sound control value correspond to the
46 minimum (resp maximum) sound control value correspond to the
|
| H A D | sirf-audio-port.txt | 8 These strings correspond 1:1 with the ordered pairs in dmas.
|
| H A D | brcm,bcm2835-i2s.txt | 9 These strings correspond 1:1 with the ordered pairs in dmas.
|
| H A D | sprd-pcm.txt | 7 These strings correspond 1:1 with the ordered pairs in dmas.
|
| /openbmc/linux/Documentation/virt/ |
| H A D | paravirt_ops.rst | 24 These operations correspond to high-level functionality where it is
28 Usually these operations correspond to low-level critical instructions. They
|
| /openbmc/linux/Documentation/ABI/testing/ |
| H A D | sysfs-bus-iio-light-lm3533-als | 32 These thresholds correspond to the eight zone-boundary
52 These values correspond to the ALS-mapper target registers for
|
| /openbmc/linux/drivers/media/platform/st/sti/delta/ |
| H A D | delta-mjpeg-fw.h | 207 * ceh_registers[0] correspond to register MBE_CEH_0_7,
208 * ceh_registers[1] correspond to register MBE_CEH_8_15
209 * ceh_registers[2] correspond to register MBE_CEH_16_23
|
| /openbmc/linux/Documentation/devicetree/bindings/remoteproc/ |
| H A D | ti,pru-consumer.yaml | 39 correspond to the PRU cores listed in the 'ti,prus' property
50 should correspond to the PRU cores listed in the 'ti,prus' property. The
|
| /openbmc/linux/Documentation/devicetree/bindings/serial/ |
| H A D | pl011.yaml | 55 When present, the first clock listed must correspond to
58 must correspond to the PCLK clocking the internal logic
|
| /openbmc/linux/arch/mips/kernel/ |
| H A D | cmpxchg.c | 24 * Calculate a shift & mask that correspond to the value we wish to in __xchg_small()
66 * Calculate a shift & mask that correspond to the value we wish to in __cmpxchg_small()
|
| /openbmc/linux/tools/include/uapi/linux/ |
| H A D | stat.h | 176 * Note that the flags marked [I] correspond to the FS_IOC_SETFLAGS flags
177 * semantically. Where possible, the numerical value is picked to correspond
179 * direct access state. It does not correspond to the per-inode flag that
|
| /openbmc/openbmc/poky/meta/lib/patchtest/tests/ |
| H A D | test_mbox.py | 116 …'Series sent to the wrong mailing list or some patches from the series correspond to different mai…
124 …'Series sent to the wrong mailing list or some patches from the series correspond to different mai…
132 …'Series sent to the wrong mailing list or some patches from the series correspond to different mai…
|
| /openbmc/linux/include/uapi/linux/ |
| H A D | stat.h | 176 * Note that the flags marked [I] correspond to the FS_IOC_SETFLAGS flags
177 * semantically. Where possible, the numerical value is picked to correspond
179 * direct access state. It does not correspond to the per-inode flag that
|
| /openbmc/u-boot/board/freescale/common/ |
| H A D | vsc3316_3308.c | 87 /* Turn ON the Output driver correspond to required output*/ in vsc3316_config()
180 /* Turn off the Output driver correspond to required output*/ in vsc3308_config_adjust()
255 /* Turn ON the Output driver correspond to required output*/ in vsc3308_config()
|
| /openbmc/linux/Documentation/devicetree/bindings/media/ |
| H A D | amphion,vpu.yaml | 45 Each vpu encoder or decoder correspond a MU, which used for communication
52 Each core correspond a decoder or encoder, need to configure them
|
| /openbmc/linux/Documentation/driver-api/rapidio/ |
| H A D | tsi721.rst | 26 This parameter can be changed bit masks that correspond to the specific
60 correspond to MBOX0 - MBOX3. MBOX is under driver's control if the
|
| /openbmc/linux/Documentation/devicetree/bindings/display/imx/ |
| H A D | fsl-imx-drm.txt | 40 Ports 0 and 1 should correspond to CSI0 and CSI1,
41 ports 2 and 3 should correspond to DI0 and DI1, respectively.
|
| /openbmc/phosphor-power/phosphor-power-sequencer/src/ |
| H A D | power_sequencer_device.hpp | 64 * The vector indices correspond to the libgpiod line offsets. For example,
66 * 0. These offsets may correspond to logical pin IDs, but they are usually
|
| /openbmc/u-boot/doc/device-tree-bindings/exynos/ |
| H A D | soc.txt | 4 node. Since the cpu id of some Exynos variants does not correspond to product
|
| /openbmc/linux/arch/arc/include/asm/ |
| H A D | dsp.h | 15 * structure fields name must correspond to aux register defenitions for
|
| /openbmc/linux/tools/include/nolibc/ |
| H A D | errno.h | 21 * because they all correspond to the highest addressable memory page.
|
| /openbmc/openbmc/poky/documentation/test-manual/ |
| H A D | yocto-project-compatible.rst | 92 kernel modules needed for the hardware. Such layers usually correspond
99 correspond to a :term:`DISTRO` setting.
|
| /openbmc/linux/Documentation/devicetree/bindings/crypto/ |
| H A D | brcm,spu-crypto.txt | 15 Mailbox channels correspond to DMA rings on the device.
|
| /openbmc/phosphor-ipmi-blobs/ |
| H A D | README.md | 106 char blob_id[]; /* Must correspond to a valid blob. */
240 char blob_id[]; /* Must correspond to a valid blob. */
257 char blob_id[]; /* Must correspond to a valid blob. */
|
| /openbmc/openbmc/meta-openembedded/meta-python/recipes-devtools/python/ |
| H A D | python3-oauthlib_3.2.2.bb | 13 # The upstream names may not correspond exactly to bitbake package names.
|