/openbmc/linux/arch/arm64/boot/dts/qcom/ |
H A D | sdm845-xiaomi-beryllium-common.dtsi | 508 max-speed = <3200000>;
|
/openbmc/linux/arch/arm64/boot/dts/broadcom/bcmbca/ |
H A D | bcm4908.dtsi | 264 speed = <1000>;
|
/openbmc/phosphor-fan-presence/ |
H A D | README.md | 167 Monitors the functional state of fans by comparing the fan feedback speed
|
/openbmc/linux/drivers/net/phy/ |
H A D | microchip_t1.c | 796 phydev->speed = SPEED_UNKNOWN; in lan87xx_read_status()
|
/openbmc/openbmc/ |
H A D | README.md | 80 get up to speed on OpenBMC development out
|
/openbmc/linux/include/net/ |
H A D | bonding.h | 175 u32 speed; member
|
/openbmc/u-boot/doc/ |
H A D | README.distro | 352 device is not attached to USB, and you wish to increase boot speed by 360 device is not attached to PCI, and you wish to increase boot speed by
|
/openbmc/linux/sound/usb/misc/ |
H A D | ua101.c | 983 switch (ua->dev->speed) { in detect_usb_format() 1255 ua->dev->speed == USB_SPEED_HIGH ? "high" : "full"); in ua101_probe()
|
/openbmc/linux/drivers/net/ethernet/xilinx/ |
H A D | ll_temac_main.c | 716 link_state = phy->speed | (phy->duplex << 1) | phy->link; in temac_adjust_link() 723 switch (phy->speed) { in temac_adjust_link()
|
/openbmc/linux/drivers/net/ethernet/freescale/ |
H A D | gianfar_ethtool.c | 200 switch (phydev->speed) { in gfar_usecs2ticks() 227 switch (phydev->speed) { in gfar_ticks2usecs()
|
/openbmc/linux/drivers/net/vmxnet3/ |
H A D | vmxnet3_ethtool.c | 656 ecmd->base.speed = adapter->link_speed; in vmxnet3_get_link_ksettings() 659 ecmd->base.speed = SPEED_UNKNOWN; in vmxnet3_get_link_ksettings()
|
/openbmc/linux/drivers/net/ethernet/cavium/thunder/ |
H A D | nic_main.c | 945 mbx.link_status.speed = link.speed; in nic_link_status_get()
|
/openbmc/linux/drivers/phy/tegra/ |
H A D | xusb.c | 1393 enum usb_device_speed speed) in tegra_xusb_padctl_enable_phy_sleepwalk() argument 1398 return lane->pad->ops->enable_phy_sleepwalk(lane, speed); in tegra_xusb_padctl_enable_phy_sleepwalk()
|
/openbmc/linux/drivers/net/ethernet/stmicro/stmmac/ |
H A D | stmmac_ethtool.c | 321 cmd->base.speed = SPEED_UNKNOWN; in stmmac_ethtool_get_link_ksettings() 327 cmd->base.speed = priv->xstats.pcs_speed; in stmmac_ethtool_get_link_ksettings()
|
/openbmc/linux/drivers/net/ethernet/intel/fm10k/ |
H A D | fm10k_pf.c | 139 switch (hw->bus.speed) { in fm10k_init_hw_pf() 746 switch (hw->bus.speed) { in fm10k_iov_configure_tc_pf()
|
/openbmc/linux/arch/s390/kernel/ |
H A D | perf_cpum_cf.c | 358 unsigned int speed:1; /* CPU speed set */ member 400 te->speed = 1; in cfdiag_trailer()
|
/openbmc/linux/drivers/net/dsa/ |
H A D | bcm_sf2.c | 838 int speed, int duplex, in bcm_sf2_sw_mac_link_up() argument 874 switch (speed) { in bcm_sf2_sw_mac_link_up()
|
/openbmc/linux/drivers/pcmcia/ |
H A D | yenta_socket.c | 459 (card_start >> 26) || mem->speed > 1000) in yenta_set_mem_map() 479 switch (to_cycles(mem->speed)) { in yenta_set_mem_map()
|
/openbmc/linux/Documentation/networking/ |
H A D | phy.rst | 264 The 802.3 control word is re-purposed to send the negotiated speed and 318 same capabilities in terms of link speed and negotiation. 460 Next, you need to specify what features (speed, duplex, autoneg,
|
/openbmc/linux/arch/arm/boot/dts/nvidia/ |
H A D | tegra30-asus-transformer-common.dtsi | 1067 nvidia,high-speed-mode = <TEGRA_PIN_DISABLE>; 1079 nvidia,high-speed-mode = <TEGRA_PIN_DISABLE>; 1109 max-speed = <4000000>;
|
H A D | tegra20-acer-a500-picasso.dts | 325 nvidia,high-speed-mode = <TEGRA_PIN_DISABLE>; 338 nvidia,high-speed-mode = <TEGRA_PIN_DISABLE>; 416 max-speed = <3375000>;
|
/openbmc/linux/drivers/net/ethernet/socionext/ |
H A D | netsec.c | 448 if (phydev->speed != SPEED_1000) in netsec_mac_update_to_phy_state() 452 phydev->speed == SPEED_100) in netsec_mac_update_to_phy_state() 1498 if (phydev->speed != SPEED_1000) in netsec_start_gmac()
|
/openbmc/linux/arch/arm64/boot/dts/freescale/ |
H A D | imx8mm.dtsi | 586 cpu_speed_grade: speed-grade@10 { /* 0x440 */ 1360 fsl,max-link-speed = <2>; 1383 fsl,max-link-speed = <2>;
|
/openbmc/linux/Documentation/ABI/testing/ |
H A D | sysfs-devices-system-cpu | 244 Description: Discover and change clock speed of CPUs 246 Clock scaling allows you to change the clock speed of the 248 power, because the lower the clock speed, the less power
|
/openbmc/linux/drivers/net/dsa/ocelot/ |
H A D | felix.c | 1097 int speed, int duplex, in felix_phylink_mac_link_up() argument 1104 interface, speed, duplex, tx_pause, rx_pause, in felix_phylink_mac_link_up() 1108 felix->info->port_sched_speed_set(ocelot, port, speed); in felix_phylink_mac_link_up()
|