| /openbmc/linux/Documentation/devicetree/bindings/net/ |
| H A D | ti,dp83822.yaml | 36 This property is only applicable if the fiber mode support is strapped
44 Fiber mode support can also be strapped. If the strap pin is not set
46 If the fiber mode is not strapped then signal detection for the PHY
|
| H A D | ti,dp83867.yaml | 103 This denotes the fact that the board has RX_DV/RX_CTRL pin strapped in
105 software needs to take when this pin is strapped in these modes.
|
| /openbmc/linux/Documentation/devicetree/bindings/pci/ |
| H A D | fsl,pci.txt | 3 Typically any Freescale PCI-X bridge hardware strapped into Agent mode
9 enumeration despite being strapped into Agent mode.
|
| /openbmc/linux/Documentation/devicetree/bindings/display/panel/ |
| H A D | tpo,tpg110.yaml | 16 driver is strapped up in electronics to the desired resolution
18 SPI. By talking to the TPG110 over SPI, the strapped properties
|
| /openbmc/linux/Documentation/devicetree/bindings/mfd/ |
| H A D | rohm,bd9571mwv.yaml | 53 power switch (the RSTBMODE pin is strapped low).
59 power switch (the RSTBMODE pin is strapped high).
|
| /openbmc/linux/Documentation/devicetree/bindings/mtd/ |
| H A D | jedec,spi-nor.yaml | 81 strapped to LOW, the status register nonvolatile bits become read-only and
87 the SRWD bit while writing the status register. WP# signal hard strapped to GND
|
| /openbmc/linux/drivers/net/phy/ |
| H A D | dp83867.c | 677 /* For non-OF device, the RX and TX ID values are either strapped in dp83867_of_init()
748 /* Force speed optimization for the PHY even if it strapped */ in dp83867_config_init()
758 /* RX_DV/RX_CTRL strapped in mode 1 or mode 2 workaround */ in dp83867_config_init()
897 * not strapped to mode 3 or 4 in HW. This is required for SGMII in dp83867_config_init()
|
| H A D | dp83822.c | 503 * SD_EN pins are strapped. Signal detection can only enabled if FX_EN in dp83822_of_init()
504 * is strapped otherwise signal detection is disabled for the PHY. in dp83822_of_init()
|
| H A D | dp83869.c | 796 /* Force speed optimization for the PHY even if it strapped */ in dp83869_config_init()
|
| H A D | broadcom.c | 623 /* The PHY is strapped in RGMII-fiber mode when INTERF_SEL[1:0] in bcm54616s_probe()
|
| /openbmc/u-boot/arch/arm/mach-mvebu/ |
| H A D | spl.c | 42 * Now check the SAR register for the strapped boot-device in get_boot_device()
|
| /openbmc/linux/drivers/usb/cdns3/ |
| H A D | drd.c | 464 dev_dbg(cdns->dev, "Controller strapped to HOST\n"); in cdns_drd_init()
470 dev_dbg(cdns->dev, "Controller strapped to PERIPHERAL\n"); in cdns_drd_init()
|
| /openbmc/linux/drivers/net/dsa/mv88e6xxx/ |
| H A D | smi.c | 14 * (ADDR[0] is always zero, thus only even SMI addresses can be strapped).
|
| /openbmc/linux/drivers/watchdog/ |
| H A D | bcm7038_wdt.c | 40 /* MIPS chips strapped for BE will automagically configure the in bcm7038_wdt_write()
|
| /openbmc/linux/drivers/char/hw_random/ |
| H A D | bcm2835-rng.c | 45 /* MIPS chips strapped for BE will automagically configure the in rng_readl()
|
| /openbmc/linux/drivers/irqchip/ |
| H A D | irq-brcmstb-l2.c | 207 /* MIPS chips strapped for BE will automagically configure the in brcmstb_l2_intc_of_init()
|
| H A D | irq-bcm7120-l2.c | 274 /* MIPS chips strapped for BE will automagically configure the in bcm7120_l2_intc_probe()
|
| /openbmc/linux/drivers/net/mdio/ |
| H A D | mdio-bcm-unimac.c | 49 /* MIPS chips strapped for BE will automagically configure the in unimac_mdio_readl()
|
| /openbmc/linux/drivers/mtd/spi-nor/ |
| H A D | swp.c | 220 * WP# pin hard strapped to GND can be a valid use case. in spi_nor_sr_lock()
|
| /openbmc/linux/sound/soc/codecs/ |
| H A D | zl38060.c | 14 // - chip must be strapped for "host boot": in this mode, firmware will be
|
| /openbmc/linux/drivers/net/ethernet/broadcom/genet/ |
| H A D | bcmmii.c | 320 * strapped or programmed correctly by the boot loader so we should in bcmgenet_mii_probe()
|
| H A D | bcmgenet.h | 657 /* MIPS chips strapped for BE will automagically configure the \
|
| /openbmc/qemu/hw/misc/ |
| H A D | aspeed_scu.c | 457 * Strapped frequencies for the AST2400 in MHz. They depend on the
|
| /openbmc/linux/drivers/edac/ |
| H A D | i5100_edac.c | 1003 /* figure out how many ranks, from strapped state of 48GB_Mode input */ in i5100_init_one()
|
| /openbmc/linux/drivers/net/ethernet/broadcom/asp2/ |
| H A D | bcmasp_intf.c | 1029 * been strapped or programmed correctly by the boot loader so in bcmasp_netif_init()
|