/openbmc/linux/Documentation/devicetree/bindings/net/ |
H A D | altr,tse.yaml | 4 $id: http://devicetree.org/schemas/net/altr,tse.yaml# 7 title: Altera Triple Speed Ethernet MAC driver (TSE) 15 - const: altr,tse-1.0 16 - const: ALTR,tse-1.0 18 - const: altr,tse-msgdma-1.0 41 If present, TSE supports additional unicast addresses. 46 If present, TSE supports hash based multicast filter. 56 const: altr,tse-mdio 75 - altr,tse-1.0 76 - ALTR,tse-1.0 [all …]
|
H A D | socfpga-dwmac.txt | 27 altr,sgmii-to-sgmii-converter: phandle to the TSE SGMII converter
|
/openbmc/u-boot/doc/device-tree-bindings/net/ |
H A D | altera_tse.txt | 1 * Altera Triple-Speed Ethernet MAC driver (TSE) 4 - compatible: Should be "altr,tse-1.0" for legacy SGDMA based TSE, and should 5 be "altr,tse-msgdma-1.0" for the preferred MSGDMA based TSE. 16 - interrupts: Should contain the TSE interrupts and it's mode. 27 If present, TSE supports additional unicast addresses. 30 If present, TSE supports a hash based multicast filter. 33 - mdio device tree subnode: When the TSE has a phy connected to its local 37 - compatible: Must be "altr,tse-mdio". 54 compatible = "altr,tse-msgdma-1.0"; 75 compatible = "altr,tse-mdio"; [all …]
|
/openbmc/u-boot/arch/x86/cpu/coreboot/ |
H A D | timestamp.c | 34 struct timestamp_entry *tse; in timestamp_add() local 39 tse = &ts_table->entries[ts_table->num_entries++]; in timestamp_add() 40 tse->entry_id = id; in timestamp_add() 41 tse->entry_stamp = ts_time - ts_table->base_time; in timestamp_add() 57 struct timestamp_entry *tse = &ts_table->entries[i]; in timestamp_add_to_bootstage() local 60 switch (tse->entry_id) { in timestamp_add_to_bootstage() 79 tse->entry_stamp / in timestamp_add_to_bootstage()
|
/openbmc/linux/tools/perf/util/ |
H A D | thread-stack.c | 303 struct thread_stack_entry *tse; in thread_stack__call_return() local 311 tse = &ts->stack[idx]; in thread_stack__call_return() 312 cr.cp = tse->cp; in thread_stack__call_return() 313 cr.call_time = tse->timestamp; in thread_stack__call_return() 315 cr.branch_count = ts->branch_count - tse->branch_count; in thread_stack__call_return() 316 cr.insn_count = ts->insn_count - tse->insn_count; in thread_stack__call_return() 317 cr.cyc_count = ts->cyc_count - tse->cyc_count; in thread_stack__call_return() 318 cr.db_id = tse->db_id; in thread_stack__call_return() 319 cr.call_ref = tse->ref; in thread_stack__call_return() 321 if (tse->no_call) in thread_stack__call_return() [all …]
|
/openbmc/linux/sound/soc/atmel/ |
H A D | tse850-pcm5142.c | 3 // TSE-850 audio - ASoC driver for the Axentia TSE-850 with a PCM5142 codec 33 // 'loop2' relays are active, short-cutting the TSE-850 from channel 2. 34 // IN1, IN2, OUT1 and OUT2 are TSE-850 connectors and DAC is the PCB name 303 .name = "TSE-850", 304 .stream_name = "TSE-850-PCM", 312 .name = "TSE-850-ASoC", 443 MODULE_DESCRIPTION("ALSA SoC driver for TSE-850 with PCM5142 codec");
|
H A D | Kconfig | 91 tristate "ASoC driver for the Axentia TSE-850" 98 Axentia TSE-850 with a PCM5142 codec.
|
/openbmc/linux/Documentation/devicetree/bindings/sound/ |
H A D | axentia,tse850-pcm5142.txt | 1 Devicetree bindings for the Axentia TSE-850 audio complex 39 are active, short-cutting the TSE-850 from channel 2. IN1, IN2, OUT1 and OUT2 40 are TSE-850 connectors and DAC is the PCB name of the (filtered) output from
|
/openbmc/linux/drivers/net/ethernet/altera/ |
H A D | altera_msgdma.c | 2 /* Altera TSE SGDMA and MSGDMA Linux driver 46 "TSE Rx mSGDMA resetting bit never cleared!\n"); in msgdma_reset() 68 "TSE Tx mSGDMA resetting bit never cleared!\n"); in msgdma_reset()
|
H A D | altera_tse_main.c | 132 if (of_device_is_compatible(child_node, "altr,tse-mdio")) { in altera_tse_mdio_create() 380 /* DMA transfer from TSE starts with 2 additional bytes for in tse_rx() 886 /* Reset and configure TSE MAC and probe associated PHY */ in tse_open() 898 netdev_warn(dev, "TSE revision %x\n", priv->revision); in tse_open() 986 /* Stop TSE MAC interface and put the device in an inactive state 1132 /* Probe Altera TSE MAC device 1400 dev_err(&pdev->dev, "failed to register TSE net device\n"); in altera_tse_probe() 1409 dev_info(&pdev->dev, "Altera TSE MAC version %d.%d at 0x%08lx irq %d/%d\n", in altera_tse_probe() 1465 /* Remove Altera TSE MAC device 1522 { .compatible = "altr,tse-msgdma-1.0", .data = &altera_dtype_msgdma, }, [all …]
|
H A D | Kconfig | 12 This driver supports the Altera Triple-Speed (TSE) Ethernet MAC.
|
H A D | altera_utils.h | 2 /* Altera TSE SGDMA and MSGDMA Linux driver
|
H A D | altera_msgdma.h | 2 /* Altera TSE SGDMA and MSGDMA Linux driver
|
H A D | altera_sgdma.h | 2 /* Altera TSE SGDMA and MSGDMA Linux driver
|
H A D | altera_utils.c | 2 /* Altera TSE SGDMA and MSGDMA Linux driver
|
H A D | altera_sgdmahw.h | 2 /* Altera TSE SGDMA and MSGDMA Linux driver
|
/openbmc/linux/arch/nios2/boot/dts/ |
H A D | 10m50_devboard.dts | 86 compatible = "altr,tse-msgdma-1.0", "altr,tse-1.0"; 109 compatible = "altr,tse-mdio";
|
H A D | 3c120_devboard.dts | 98 compatible = "altr,tse-1.0"; 114 compatible = "altr,tse-mdio";
|
/openbmc/u-boot/arch/nios2/dts/ |
H A D | 10m50_devboard.dts | 102 compatible = "altr,tse-msgdma-1.0", "altr,tse-1.0"; 126 compatible = "altr,tse-mdio";
|
H A D | 3c120_devboard.dts | 107 compatible = "altr,tse-1.0"; 123 compatible = "altr,tse-mdio";
|
/openbmc/linux/Documentation/networking/device_drivers/ethernet/altera/ |
H A D | altera_tse.rst | 11 This is the driver for the Altera Triple-Speed Ethernet (TSE) controllers 156 The statistics supported by the TSE and the device driver are as follows: 274 Altera TSE. This statistics counts the number of received good and errored 276 in the frm_length register. See the Altera TSE User Guide for More details.
|
/openbmc/u-boot/drivers/net/ |
H A D | altera_tse.c | 523 /* start TSE */ in altera_tse_start() 524 debug("Configuring TSE Mac\n"); in altera_tse_start() 660 debug("Reset TSE & SGDMAs\n"); in altera_tse_probe() 701 { .compatible = "altr,tse-msgdma-1.0", .data = ALT_MSGDMA }, 702 { .compatible = "altr,tse-1.0", .data = ALT_SGDMA },
|
/openbmc/linux/arch/arm/boot/dts/microchip/ |
H A D | at91-tse850-3.dts | 3 * at91-tse850-3.dts - Device Tree file for the Axentia TSE-850 3.0 board 14 model = "Axentia TSE-850 3.0";
|
/openbmc/linux/drivers/media/i2c/cx25840/ |
H A D | cx25840-ir.c | 498 int tsr, rsr, rto, ror, tse, rse, rte, roe, kror; in cx25840_ir_irq_handler() local 522 tse = irqen & IRQEN_TSE; /* Tx FIFO Service Request IRQ Enable */ in cx25840_ir_irq_handler() 534 tse ? "tse" : " ", rse ? "rse" : " ", in cx25840_ir_irq_handler() 540 if (tse && tsr) { in cx25840_ir_irq_handler()
|
/openbmc/linux/drivers/media/pci/cx23885/ |
H A D | cx23888-ir.c | 514 int tsr, rsr, rto, ror, tse, rse, rte, roe, kror; in cx23888_ir_irq_handler() local 521 tse = irqen & IRQEN_TSE; /* Tx FIFO Service Request IRQ Enable */ in cx23888_ir_irq_handler() 534 tse ? "tse" : " ", rse ? "rse" : " ", in cx23888_ir_irq_handler() 540 if (tse && tsr) { in cx23888_ir_irq_handler()
|