cpufreq: imx: update the clock switch flow to support imx6ul

For i.MX6UL, the clock switch flow is slightly different from
other i.MX6 SOCs. It has a 'secondary_sel' clk that will be use

cpufreq: imx: update the clock switch flow to support imx6ul

For i.MX6UL, the clock switch flow is slightly different from
other i.MX6 SOCs. It has a 'secondary_sel' clk that will be used
when the CPU freq is higher than 396MHz. So the clock switch flow in
'set_target' callback need to update to support i.MX6UL in the common
i.MX6 SOC cpufreq driver.

Signed-off-by: Bai Ping <b51503@freescale.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

PM / OPP: Prefix exported opp routines with dev_pm_opp_

That's the naming convention followed in most of opp core, but few
routines didn't follow this, fix them.

Reviewed-by: St

PM / OPP: Prefix exported opp routines with dev_pm_opp_

That's the naming convention followed in most of opp core, but few
routines didn't follow this, fix them.

Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

PM / OPP: Rename opp init/free table routines

free-table routines are opposite of init-table ones, and must be named
to make that clear. Opposite of 'init' is 'exit', but those doesn't s

PM / OPP: Rename opp init/free table routines

free-table routines are opposite of init-table ones, and must be named
to make that clear. Opposite of 'init' is 'exit', but those doesn't suit
really well.

Replace 'init' with 'add' and 'free' with 'remove'.

Reported-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.1

Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.

They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.

Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.

Everything has been in linux-next for a while"

* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...

show more ...

imx6q: free OPP table created during ->init()

OPP layer now supports freeing of OPPs and we should free them once they aren't
useful anymore.

Signed-off-by: Viresh Kumar <viresh

imx6q: free OPP table created during ->init()

OPP layer now supports freeing of OPPs and we should free them once they aren't
useful anymore.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

cpufreq: drop owner assignment from platform_drivers

A platform_driver does not need to set an owner, it will be populated by the
driver core.

Signed-off-by: Wolfram Sang <wsa@t

cpufreq: drop owner assignment from platform_drivers

A platform_driver does not need to set an owner, it will be populated by the
driver core.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

show more ...

cpufreq: imx6: remove pu regulator dependency for SOCs with no PU regulator

PU regulator is not a necessary regulator for cpufreq, not all
i.MX6 SoCs have PU regulator, only if SOC has P

cpufreq: imx6: remove pu regulator dependency for SOCs with no PU regulator

PU regulator is not a necessary regulator for cpufreq, not all
i.MX6 SoCs have PU regulator, only if SOC has PU regulator, then its
voltage must be equal to SOC regulator, so remove the dependency
to support i.MX6SX which has no PU regulator.

Signed-off-by: Anson Huang <b20788@freescale.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

cpufreq: imx6q: Remove unused include

There is no need to include delay.h.

Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Sig

cpufreq: imx6q: Remove unused include

There is no need to include delay.h.

Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

cpufreq: imx6q: Drop devm_clk/regulator_get usage

This driver is using devres managed calls incorrectly, giving the cpu0
device as first parameter instead of the cpufreq platform device.

cpufreq: imx6q: Drop devm_clk/regulator_get usage

This driver is using devres managed calls incorrectly, giving the cpu0
device as first parameter instead of the cpufreq platform device.
This results in resources not being freed if the cpufreq platform device
is unbound, for example if probing has to be deferred for a missing
regulator.
Supporting probe deferral properly is a prerequisite to enabling the
internal LDO bypass on i.MX6 and regulating the CPU voltage with an
external regulator.

Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

cpufreq: Remove cpufreq_generic_exit()

cpufreq_generic_exit() is empty now and can be deleted.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wys

cpufreq: Remove cpufreq_generic_exit()

cpufreq_generic_exit() is empty now and can be deleted.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

cpufreq: introduce cpufreq_generic_get() routine

CPUFreq drivers that use clock frameworks interface,i.e. clk_get_rate(),
to get CPUs clk rate, have similar sort of code used in most of

cpufreq: introduce cpufreq_generic_get() routine

CPUFreq drivers that use clock frameworks interface,i.e. clk_get_rate(),
to get CPUs clk rate, have similar sort of code used in most of them.

This patch adds a generic ->get() which will do the same thing for them.
All those drivers are required to now is to set .get to cpufreq_generic_get()
and set their clk pointer in policy->clk during ->init().

Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

cpufreq: Mark ARM drivers with CPUFREQ_NEED_INITIAL_FREQ_CHECK flag

Sometimes boot loaders set CPU frequency to a value outside of frequency table
present with cpufreq core. In such case

cpufreq: Mark ARM drivers with CPUFREQ_NEED_INITIAL_FREQ_CHECK flag

Sometimes boot loaders set CPU frequency to a value outside of frequency table
present with cpufreq core. In such cases CPU might be unstable if it has to run
on that frequency for long duration of time and so its better to set it to a
frequency which is specified in frequency table.

On some systems we can't really say what frequency we're running at the moment
and so for these we shouldn't check if we are running at a frequency present in
frequency table. And so we really can't force this for all the cpufreq drivers.

Hence we are created another flag here: CPUFREQ_NEED_INITIAL_FREQ_CHECK that
will be marked by platforms which want to go for this check at boot time.

Initially this is done for all ARM platforms but others may follow if required.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

cpufreq: imx6q: add of_init_opp_table

Add a routine check to see if the platform supplied the OPP table.
Incase there's no OPP table exist, it will try to initialise it.

It's be

cpufreq: imx6q: add of_init_opp_table

Add a routine check to see if the platform supplied the OPP table.
Incase there's no OPP table exist, it will try to initialise it.

It's been tested on iMX6SL board where the platform doesn't have
an OPP table.

Signed-off-by: John Tobias <john.tobias.ph@gmail.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

cpufreq: imx6q: correct VDDSOC/PU voltage scaling when cpufreq is changed

on i.MX6Q, cpu freq change need to follow below flows:

1. each setpoint has different VDDARM, VDDSOC/PU vol

cpufreq: imx6q: correct VDDSOC/PU voltage scaling when cpufreq is changed

on i.MX6Q, cpu freq change need to follow below flows:

1. each setpoint has different VDDARM, VDDSOC/PU voltage, get the setpoint
table from dts;
2. when cpu freq is scaling up, need to increase VDDSOC/PU voltage before
VDDARM, if VDDPU is off, no need to change it;
3. when cpu freq is scaling down, need to decrease VDDARM voltage before
VDDSOC/PU, if VDDPU is off, no need to change it;

normally dts will pass vddsoc/pu freq/volt info to kernel, if not, will
use fixed value for vddsoc/pu voltage setting.

Signed-off-by: Anson Huang <b20788@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

cpufreq: move freq change notifications to cpufreq core

Most of the drivers do following in their ->target_index() routines:

struct cpufreq_freqs freqs;
freqs.ol

cpufreq: move freq change notifications to cpufreq core

Most of the drivers do following in their ->target_index() routines:

struct cpufreq_freqs freqs;
freqs.old = old freq...
freqs.new = new freq...

cpufreq_notify_transition(policy, &freqs, CPUFREQ_PRECHANGE);

/* Change rate here */

cpufreq_notify_transition(policy, &freqs, CPUFREQ_POSTCHANGE);

This is replicated over all cpufreq drivers today and there doesn't exists a
good enough reason why this shouldn't be moved to cpufreq core instead.

There are few special cases though, like exynos5440, which doesn't do everything
on the call to ->target_index() routine and call some kind of bottom halves for
doing this work, work/tasklet/etc..

They may continue doing notification from their own code as flag:
CPUFREQ_ASYNC_NOTIFICATION is already set for them.

All drivers are also modified in this patch to avoid breaking 'git bisect', as
double notification would happen otherwise.

Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Russell King <linux@arm.linux.org.uk>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

cpufreq: Implement light weight ->target_index() routine

Currently, the prototype of cpufreq_drivers target routines is:

int target(struct cpufreq_policy *policy, unsigned int targe

cpufreq: Implement light weight ->target_index() routine

Currently, the prototype of cpufreq_drivers target routines is:

int target(struct cpufreq_policy *policy, unsigned int target_freq,
unsigned int relation);

And most of the drivers call cpufreq_frequency_table_target() to get a valid
index of their frequency table which is closest to the target_freq. And they
don't use target_freq and relation after that.

So, it makes sense to just do this work in cpufreq core before calling
cpufreq_frequency_table_target() and simply pass index instead. But this can be
done only with drivers which expose their frequency table with cpufreq core. For
others we need to stick with the old prototype of target() until those drivers
are converted to expose frequency tables.

This patch implements the new light weight prototype for target_index() routine.
It looks like this:

int target_index(struct cpufreq_policy *policy, unsigned int index);

CPUFreq core will call cpufreq_frequency_table_target() before calling this
routine and pass index to it. Because CPUFreq core now requires to call routines
present in freq_table.c CONFIG_CPU_FREQ_TABLE must be enabled all the time.

This also marks target() interface as deprecated. So, that new drivers avoid
using it. And Documentation is updated accordingly.

It also converts existing .target() to newly defined light weight
.target_index() routine for many driver.

Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Russell King <linux@arm.linux.org.uk>
Acked-by: David S. Miller <davem@davemloft.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rjw@rjwysocki.net>

show more ...

Merge back earlier 'pm-cpufreq' material.

Conflicts:
drivers/cpufreq/omap-cpufreq.c

PM / OPP: rename header to linux/pm_opp.h

Since Operating Performance Points (OPP) functions are specific
to device specific power management, be specific and rename opp.h
to pm_opp.

PM / OPP: rename header to linux/pm_opp.h

Since Operating Performance Points (OPP) functions are specific
to device specific power management, be specific and rename opp.h
to pm_opp.h

Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

PM / OPP: rename data structures to dev_pm equivalents

Since Operating Performance Points (OPP) data structures are specific
to device specific power management, be specific and rename o

PM / OPP: rename data structures to dev_pm equivalents

Since Operating Performance Points (OPP) data structures are specific
to device specific power management, be specific and rename opp_* data
structures in OPP library with dev_pm_opp_* equivalent.

Affected structures are:
struct opp
enum opp_event

Minor checkpatch warning resulting of this change was fixed as well.

Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

PM / OPP: rename functions to dev_pm_opp*

Since Operating Performance Points (OPP) functions are specific to
device specific power management, be specific and rename opp_*
accessors

PM / OPP: rename functions to dev_pm_opp*

Since Operating Performance Points (OPP) functions are specific to
device specific power management, be specific and rename opp_*
accessors in OPP library with dev_pm_opp_* equivalent.

Affected functions are:
opp_get_voltage
opp_get_freq
opp_get_opp_count
opp_find_freq_exact
opp_find_freq_floor
opp_find_freq_ceil
opp_add
opp_enable
opp_disable
opp_get_notifier
opp_init_cpufreq_table
opp_free_cpufreq_table

Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

cpufreq: imx6q: use cpufreq_generic_init()

Use generic cpufreq_generic_init() routine instead of replicating the same code
here.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro

cpufreq: imx6q: use cpufreq_generic_init()

Use generic cpufreq_generic_init() routine instead of replicating the same code
here.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

cpufreq: imx6q: don't initialize part of policy set by core

Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch rem

cpufreq: imx6q: don't initialize part of policy set by core

Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.

Most recent of those changes is to call ->get() in the core after calling
->init().

Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

cpufreq: imx6q: Use generic cpufreq routines

Most of the CPUFreq drivers do similar things in .exit() and .verify() routines
and .attr. So its better if we have generic routines for them

cpufreq: imx6q: Use generic cpufreq routines

Most of the CPUFreq drivers do similar things in .exit() and .verify() routines
and .attr. So its better if we have generic routines for them which can be used
by cpufreq drivers then.

This patch uses these generic routines for in the imx6q driver.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

cpufreq: imx6q: use cpufreq_table_validate_and_show()

Lets use cpufreq_table_validate_and_show() instead of calling
cpufreq_frequency_table_cpuinfo() and cpufreq_frequency_table_get_attr

cpufreq: imx6q: use cpufreq_table_validate_and_show()

Lets use cpufreq_table_validate_and_show() instead of calling
cpufreq_frequency_table_cpuinfo() and cpufreq_frequency_table_get_attr().

Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

cpufreq: imx6q-cpufreq: assign cpu_dev correctly to cpu0 device

Commit cdc58d602d2e657602a90c190cbf745886c95977 "cpufreq: imx6q-cpufreq:
remove device tree parsing for cpu nodes" assumed

cpufreq: imx6q-cpufreq: assign cpu_dev correctly to cpu0 device

Commit cdc58d602d2e657602a90c190cbf745886c95977 "cpufreq: imx6q-cpufreq:
remove device tree parsing for cpu nodes" assumed the pdev->dev is set to
cpu0 device in the platform code. But it actually points to the virtual
cpufreq-cpu0 platform device which is not present in the device tree.
Most of the information needed by cpufreq is stored in cpu0 DT node.
So cpu_dev must point to cpu0 device.

This patch fixes the wrong assignment to cpu_dev.

Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...