Home
last modified time | relevance | path

Searched refs:SPD (Results 1 – 25 of 32) sorted by relevance

12

/openbmc/openbmc/meta-arm/meta-arm/recipes-bsp/trusted-firmware-a/files/
H A D0001-fix-zynqmp-handle-secure-SGI-at-EL1-for-OP-TEE.patch8 GICV2_G0_FOR_EL3 to 0 when the SPD is OP-TEE.
25 # pncd SPD requires secure SGI to be handled at EL1
26 -ifeq (${SPD}, $(filter ${SPD},pncd tspd))
27 +ifeq (${SPD}, $(filter ${SPD},pncd tspd opteed))
29 $(error "Error: ZYNQMP_WDT_RESTART and SPD=pncd are incompatible")
/openbmc/u-boot/drivers/ddr/fsl/
H A DMakefile15 SPD := y macro
18 SPD := y macro
20 ifdef SPD
/openbmc/openbmc/meta-arm/meta-arm-bsp/recipes-bsp/trusted-firmware-a/
H A Dtrusted-firmware-a-corstone1000.inc20 # Enabling Secure-EL1 Payload Dispatcher (SPD)
23 # So, the SPD SPMC component should run at the S-EL1 execution state
/openbmc/u-boot/doc/
H A DREADME.fsl-ddr293 type command "print" with arguments to show SPD, options, registers
300 type command "recompute" to reload SPD and start over
313 spd - print SPD data
314 dimmparms - DIMM parameters, calculated from SPD
323 spd - print SPD data
324 dimmparms - DIMM parameters, calculated from SPD
330 byte number if the object is SPD
341 no argument - reload SPD and start over
/openbmc/u-boot/board/sbc8548/
H A DREADME65 Memory Size and using SPD:
69 for 256MB of DDR2 @400MHz. It does not by default use the DDR2 SPD
73 SPD EEPROM to land at the same address as the DDR2 SPD EEPROM, so
74 that the SPD data can not be read reliably. You can test if your
100 issue and allow SPD autodetection of RAM to work.
/openbmc/u-boot/board/freescale/p1_p2_rdb_pc/
H A DREADME26 is used to store SPD data. In case of absent or corrupted SPD, falling back
/openbmc/openbmc/meta-arm/meta-arm/recipes-bsp/trusted-firmware-a/
H A Dtrusted-firmware-a_%.bbappend18 # Enabling Secure-EL1 Payload Dispatcher (SPD) in this case
23 # The SPD SPMC component should run at the S-EL1 execution state.
H A Dtrusted-firmware-a.inc25 # Some platforms use SPD (Secure Payload Dispatcher) services
27 # Leave empty to not use SPD
120 EXTRA_OEMAKE += "${@'SPD=${TFA_SPD}' if d.getVar('TFA_SPD') else ''}"
/openbmc/linux/Documentation/userspace-api/media/v4l/
H A Dcolorspaces.rst28 Distribution (SPD) which is a graph showing the intensity (radiant
31 between the SPD and color as perceived by the human brain.
35 those receptors and are perceived as the same color, even though the SPD
42 can take an SPD and calculate the stimulus for each color receptor.
/openbmc/linux/drivers/misc/eeprom/
H A DKconfig124 tristate "SPD EEPROMs on DDR4 memory modules"
127 Enable this driver to get read support to SPD EEPROMs following
/openbmc/u-boot/drivers/ram/
H A DKconfig43 the RAM through the use of SPD (Serial Presence Detect) is supported
/openbmc/u-boot/drivers/net/
H A Dmacb.c578 ncfgr &= ~(MACB_BIT(SPD) | MACB_BIT(FD)); in macb_phy_init()
608 ncfgr &= ~(MACB_BIT(SPD) | MACB_BIT(FD) | GEM_BIT(GBE)); in macb_phy_init()
610 ncfgr |= MACB_BIT(SPD); in macb_phy_init()
/openbmc/linux/arch/powerpc/boot/dts/
H A Dturris1x.dts60 /* DDR3 SPD/EEPROM PSWP instruction */
88 /* DDR3 SPD/EEPROM */
/openbmc/openbmc/meta-arm/documentation/
H A Dtrusted-services.md42 3. trusted-firmware-a might require platform specific TF-A build parameters (SPD and SPMC details o…
/openbmc/u-boot/board/ti/am65x/
H A DREADME128 $ make CROSS_COMPILE=aarch64-linux-gnu- ARCH=aarch64 PLAT=k3 TARGET_BOARD=generic SPD=opteed
/openbmc/u-boot/doc/device-tree-bindings/misc/
H A Dintel,baytrail-fsp.txt45 do not set "fsp,enable-memory-down", then the DIMM SPD information will be
/openbmc/linux/arch/arm/boot/dts/aspeed/
H A Daspeed-bmc-asrock-x570d4u.dts228 /* FRU and SPD EEPROM SMBus */
/openbmc/linux/drivers/video/
H A Dhdmi.c1666 if (size < HDMI_INFOFRAME_SIZE(SPD)) in hdmi_spd_infoframe_unpack()
1675 if (hdmi_infoframe_checksum(buffer, HDMI_INFOFRAME_SIZE(SPD)) != 0) in hdmi_spd_infoframe_unpack()
/openbmc/u-boot/board/freescale/t4qds/
H A DREADME146 SPL further initialise DDR using SPD and environment variables
/openbmc/docs/
H A Dhw-vendor-repos-policy.md91 SPD/VPD
/openbmc/u-boot/board/freescale/t208xrdb/
H A DREADME199 SPL further initializes DDR using SPD and environment variables
/openbmc/u-boot/board/hisilicon/poplar/
H A DREADME114 SPD=none BL33=~/poplar/bin/u-boot.bin DEBUG=1 PLAT=poplar
/openbmc/u-boot/board/freescale/t208xqds/
H A DREADME218 SPL further initializes DDR using SPD and environment variables
/openbmc/u-boot/board/freescale/t104xrdb/
H A DREADME230 SPL further initialise DDR using SPD and environment variables and copy
/openbmc/u-boot/board/freescale/t102xrdb/
H A DREADME257 SPL further initializes DDR using SPD and environment variables

12