| /openbmc/u-boot/drivers/i2c/ |
| H A D | soft_i2c.c | 52 # ifndef I2C_READ
53 # define I2C_READ gpio_get_value(CONFIG_SOFT_I2C_GPIO_SDA) macro
243 nack = I2C_READ; in write_byte()
273 data |= I2C_READ; in read_byte()
|
| H A D | mv_i2c.h | 22 #define I2C_READ 0 macro
|
| H A D | davinci_i2c.h | 12 #define I2C_READ 1 macro
|
| H A D | s3c24x0_i2c.h | 63 #define I2C_READ 1 macro
|
| H A D | mv_i2c.c | 166 case I2C_READ: in i2c_transfer()
297 msg.direction = I2C_READ; in __i2c_read()
461 msg.direction = I2C_READ; in __i2c_probe_chip()
|
| H A D | s3c24x0_i2c.c | 162 case I2C_READ: in i2c_transfer()
221 ret = i2c_transfer(i2c_bus->regs, I2C_READ, chip << 1, 0, 0, buf, 1); in s3c24x0_i2c_probe()
|
| /openbmc/linux/drivers/media/pci/mantis/ |
| H A D | mantis_i2c.h | 13 #define I2C_READ (1 << 1) macro
|
| /openbmc/linux/drivers/media/usb/dvb-usb-v2/ |
| H A D | ce6230.h | 28 I2C_READ = 0xd9, /* rd 9 (unclear) */ enumerator
|
| H A D | ce6230.c | 27 case I2C_READ: in ce6230_ctrl_msg()
|
| /openbmc/linux/include/linux/dma/ |
| H A D | qcom-gpi-dma.h | 51 I2C_READ, enumerator
|
| /openbmc/linux/drivers/i2c/busses/ |
| H A D | i2c-nomadik.c | 131 I2C_READ = 0x01 enumerator
331 mcr |= GEN_MASK(I2C_READ, I2C_MCR_OP, 0); in load_i2c_mcr_reg()
580 dev->cli.operation = I2C_READ; in nmk_i2c_xfer_one()
744 if (dev->cli.operation == I2C_READ) { in i2c_irq_handler()
791 if (dev->cli.operation == I2C_READ) { in i2c_irq_handler()
|
| H A D | i2c-hix5hd2.c | 44 #define I2C_READ BIT(2) macro
201 writel_relaxed(I2C_READ | I2C_NO_ACK, priv->regs + HIX5I2C_COM); in hix5hd2_read_handle()
204 writel_relaxed(I2C_READ, priv->regs + HIX5I2C_COM); in hix5hd2_read_handle()
|
| H A D | i2c-qcom-geni.c | 30 #define I2C_READ 0x2 macro
421 geni_se_setup_m_cmd(se, I2C_READ, m_param); in geni_i2c_rx_one_msg()
623 &rx_addr, &rx_buf, I2C_READ, gi2c->rx_c); in geni_i2c_gpi_xfer()
|
| /openbmc/linux/drivers/media/dvb-frontends/ |
| H A D | gp8psk-fe.h | 16 #define I2C_READ 0x84 macro
|
| /openbmc/u-boot/include/configs/ |
| H A D | snapper9260.h | 96 #define I2C_READ at91_get_gpio_value(AT91_PIN_PA23); macro
|
| H A D | ethernut5.h | 132 #define I2C_READ at91_get_pio_value(AT91_PIO_PORTA, 23) macro
|
| H A D | vct.h | 172 #define I2C_READ vct_gpio_get(CONFIG_SYS_GPIO_I2C_SDA) macro
|
| H A D | hrcon.h | 403 #define I2C_READ \ macro
|
| H A D | strider.h | 435 #define I2C_READ \ macro
|
| /openbmc/u-boot/include/configs/km/ |
| H A D | km_arm.h | 162 #define I2C_READ (kw_gpio_get_value(KM_KIRKWOOD_SDA_PIN) ? 1 : 0) macro
|
| /openbmc/u-boot/board/keymile/km_arm/ |
| H A D | km_arm.c | 499 return I2C_READ; in get_sda()
|
| /openbmc/linux/drivers/dma/qcom/ |
| H A D | gpi.c | 1672 tre->dword[0] = u32_encode_bits(I2C_READ, TRE_I2C_GO_CMD); in gpi_create_i2c_tre()
1690 if (i2c->op == I2C_READ || i2c->multi_msg == false) { in gpi_create_i2c_tre()
|
| /openbmc/u-boot/ |
| H A D | README | 1784 I2C_READ
1789 eg: #define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
|