Merge tag 'v6.6.58' into for/openbmc/dev-6.6

This is the 6.6.58 stable release

serial: imx: Update mctrl old_status on RTSD interrupt

commit 40d7903386df4d18f04d90510ba90eedee260085 upstream.

When sending data using DMA at high baudrate (4 Mbdps in local test case) to
a devic

serial: imx: Update mctrl old_status on RTSD interrupt

commit 40d7903386df4d18f04d90510ba90eedee260085 upstream.

When sending data using DMA at high baudrate (4 Mbdps in local test case) to
a device with small RX buffer which keeps asserting RTS after every received
byte, it is possible that the iMX UART driver would not recognize the falling
edge of RTS input signal and get stuck, unable to transmit any more data.

This condition happens when the following sequence of events occur:
- imx_uart_mctrl_check() is called at some point and takes a snapshot of UART
control signal status into sport->old_status using imx_uart_get_hwmctrl().
The RTSS/TIOCM_CTS bit is of interest here (*).
- DMA transfer occurs, the remote device asserts RTS signal after each byte.
The i.MX UART driver recognizes each such RTS signal change, raises an
interrupt with USR1 register RTSD bit set, which leads to invocation of
__imx_uart_rtsint(), which calls uart_handle_cts_change().
- If the RTS signal is deasserted, uart_handle_cts_change() clears
port->hw_stopped and unblocks the port for further data transfers.
- If the RTS is asserted, uart_handle_cts_change() sets port->hw_stopped
and blocks the port for further data transfers. This may occur as the
last interrupt of a transfer, which means port->hw_stopped remains set
and the port remains blocked (**).
- Any further data transfer attempts will trigger imx_uart_mctrl_check(),
which will read current status of UART control signals by calling
imx_uart_get_hwmctrl() (***) and compare it with sport->old_status .
- If current status differs from sport->old_status for RTS signal,
uart_handle_cts_change() is called and possibly unblocks the port
by clearing port->hw_stopped .
- If current status does not differ from sport->old_status for RTS
signal, no action occurs. This may occur in case prior snapshot (*)
was taken before any transfer so the RTS is deasserted, current
snapshot (***) was taken after a transfer and therefore RTS is
deasserted again, which means current status and sport->old_status
are identical. In case (**) triggered when RTS got asserted, and
made port->hw_stopped set, the port->hw_stopped will remain set
because no change on RTS line is recognized by this driver and
uart_handle_cts_change() is not called from here to unblock the
port->hw_stopped.

Update sport->old_status in __imx_uart_rtsint() accordingly to make
imx_uart_mctrl_check() detect such RTS change. Note that TIOCM_CAR
and TIOCM_RI bits in sport->old_status do not suffer from this problem.

Fixes: ceca629e0b48 ("[ARM] 2971/1: i.MX uart handle rts irq")
Cc: stable <stable@kernel.org>
Reviewed-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20241002184133.19427-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

Merge tag 'v6.6.39' into dev-6.6

This is the 6.6.39 stable release

serial: imx: Raise TX trigger level to 8

[ Upstream commit a3d8728ab079951741efa11360df43dbfacba7ab ]

At the default TX trigger level of 2 in non-DMA mode (meaning that an
interrupt is generated wh

serial: imx: Raise TX trigger level to 8

[ Upstream commit a3d8728ab079951741efa11360df43dbfacba7ab ]

At the default TX trigger level of 2 in non-DMA mode (meaning that an
interrupt is generated when less than 2 characters are left in the
FIFO), we have observed frequent buffer underruns at 115200 Baud on an
i.MX8M Nano. This can cause communication issues if the receiving side
expects a continuous transfer.

Increasing the level to 8 makes the UART trigger an interrupt earlier,
giving the kernel enough time to refill the FIFO, at the cost of
triggering one interrupt per ~24 instead of ~30 bytes of transmitted
data (as the i.MX UART has a 32 byte FIFO).

Signed-off-by: Michael Krummsdorf <michael.krummsdorf@tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20240508133744.35858-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

Merge tag 'v6.6.37' into dev-6.6

This is the 6.6.37 stable release

serial: imx: only set receiver level if it is zero

commit 9706fc87b4cff0ac4f5d5d62327be83fe72e3108 upstream.

With commit a81dbd0463ec ("serial: imx: set receiver level before
starting uart") we set

serial: imx: only set receiver level if it is zero

commit 9706fc87b4cff0ac4f5d5d62327be83fe72e3108 upstream.

With commit a81dbd0463ec ("serial: imx: set receiver level before
starting uart") we set the receiver level to its default value. This
caused a regression when using SDMA, where the receiver level is 9
instead of 8 (default). This change will first check if the receiver
level is zero and only then set it to the default. This still avoids the
interrupt storm when the receiver level is zero.

Fixes: a81dbd0463ec ("serial: imx: set receiver level before starting uart")
Cc: stable <stable@kernel.org>
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Link: https://lore.kernel.org/r/20240703112543.148304-1-eichest@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

serial: imx: set receiver level before starting uart

commit a81dbd0463eca317eee44985a66aa6cc2ce5c101 upstream.

Set the receiver level to something > 0 before calling imx_uart_start_rx
in rs485_conf

serial: imx: set receiver level before starting uart

commit a81dbd0463eca317eee44985a66aa6cc2ce5c101 upstream.

Set the receiver level to something > 0 before calling imx_uart_start_rx
in rs485_config. This is necessary to avoid an interrupt storm that
might prevent the system from booting. This was seen on an i.MX7 device
when the rs485-rts-active-low property was active in the device tree.

Fixes: 6d215f83e5fc ("serial: imx: warn user when using unsupported configuration")
Cc: stable <stable@kernel.org>
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Link: https://lore.kernel.org/r/20240621153829.183780-1-eichest@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

Merge tag 'v6.6.36' into dev-6.6

This is the 6.6.36 stable release

serial: imx: Introduce timeout when waiting on transmitter empty

[ Upstream commit e533e4c62e9993e62e947ae9bbec34e4c7ae81c2 ]

By waiting at most 1 second for USR2_TXDC to be set, we avoid a potenti

serial: imx: Introduce timeout when waiting on transmitter empty

[ Upstream commit e533e4c62e9993e62e947ae9bbec34e4c7ae81c2 ]

By waiting at most 1 second for USR2_TXDC to be set, we avoid a potential
deadlock.

In case of the timeout, there is not much we can do, so we simply ignore
the transmitter state and optimistically try to continue.

Signed-off-by: Esben Haabendal <esben@geanix.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/919647898c337a46604edcabaf13d42d80c0915d.1712837613.git.esben@geanix.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

Merge tag 'v6.6.24' into dev-6.6

This is the 6.6.24 stable release

tty: serial: imx: Fix broken RS485

commit 672448ccf9b6a676f96f9352cbf91f4d35f4084a upstream.

When about to transmit the function imx_uart_start_tx is called and in
some RS485 configurations this fu

tty: serial: imx: Fix broken RS485

commit 672448ccf9b6a676f96f9352cbf91f4d35f4084a upstream.

When about to transmit the function imx_uart_start_tx is called and in
some RS485 configurations this function will call imx_uart_stop_rx. The
problem is that imx_uart_stop_rx will enable loopback in order to
release the RS485 bus, but when loopback is enabled transmitted data
will just be looped to RX.

This patch fixes the above problem by not enabling loopback when about
to transmit.

This driver now works well when used for RS485 half duplex master
configurations.

Fixes: 79d0224f6bf2 ("tty: serial: imx: Handle RS485 DE signal active high")
Cc: stable <stable@kernel.org>
Signed-off-by: Rickard x Andersson <rickaran@axis.com>
Tested-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Link: https://lore.kernel.org/r/20240221115304.509811-1-rickaran@axis.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

Merge tag 'v6.6.15' into dev-6.6

This is the 6.6.15 stable release

Merge tag 'v6.6.14' into dev-6.6

This is the 6.6.14 stable release

serial: Do not hold the port lock when setting rx-during-tx GPIO

commit 07c30ea5861fb26a77dade8cdc787252f6122fb1 upstream.

Both the imx and stm32 driver set the rx-during-tx GPIO in rs485_config().

serial: Do not hold the port lock when setting rx-during-tx GPIO

commit 07c30ea5861fb26a77dade8cdc787252f6122fb1 upstream.

Both the imx and stm32 driver set the rx-during-tx GPIO in rs485_config().
Since this function is called with the port lock held, this can be a
problem in case that setting the GPIO line can sleep (e.g. if a GPIO
expander is used which is connected via SPI or I2C).

Avoid this issue by moving the GPIO setting outside of the port lock into
the serial core and thus making it a generic feature.

Also with commit c54d48543689 ("serial: stm32: Add support for rs485
RX_DURING_TX output GPIO") the SER_RS485_RX_DURING_TX flag is only set if a
rx-during-tx GPIO is _not_ available, which is wrong. Fix this, too.

Furthermore reset old GPIO settings in case that changing the RS485
configuration failed.

Fixes: c54d48543689 ("serial: stm32: Add support for rs485 RX_DURING_TX output GPIO")
Fixes: ca530cfa968c ("serial: imx: Add support for RS485 RX_DURING_TX output GPIO")
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240103061818.564-2-l.sanfilippo@kunbus.com
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

serial: imx: Correct clock error message in function probe()

[ Upstream commit 3e189470cad27d41a3a9dc02649f965b7ed1c90f ]

Correct the clock error message by changing the clock name.

Fixes: 1e512d4

serial: imx: Correct clock error message in function probe()

[ Upstream commit 3e189470cad27d41a3a9dc02649f965b7ed1c90f ]

Correct the clock error message by changing the clock name.

Fixes: 1e512d45332b ("serial: imx: add error messages when .probe fails")
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231224093209.2612-1-cniedermaier@dh-electronics.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

serial: imx: fix tx statemachine deadlock

[ Upstream commit 78d60dae9a0c9f09aa3d6477c94047df2fe6f7b0 ]

When using the serial port as RS485 port, the tx statemachine is used to
control the RTS pin t

serial: imx: fix tx statemachine deadlock

[ Upstream commit 78d60dae9a0c9f09aa3d6477c94047df2fe6f7b0 ]

When using the serial port as RS485 port, the tx statemachine is used to
control the RTS pin to drive the RS485 transceiver TX_EN pin. When the
TTY port is closed in the middle of a transmission (for instance during
userland application crash), imx_uart_shutdown disables the interface
and disables the Transmission Complete interrupt. afer that,
imx_uart_stop_tx bails on an incomplete transmission, to be retriggered
by the TC interrupt. This interrupt is disabled and therefore the tx
statemachine never transitions out of SEND. The statemachine is in
deadlock now, and the TX_EN remains low, making the interface useless.

imx_uart_stop_tx now checks for incomplete transmission AND whether TC
interrupts are enabled before bailing to be retriggered. This makes sure
the state machine handling is reached, and is properly set to
WAIT_AFTER_SEND.

Fixes: cb1a60923609 ("serial: imx: implement rts delaying for rs485")
Signed-off-by: Paul Geurts <paul_geurts@live.nl>
Tested-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Tested-by: Eberhard Stoll <eberhard.stoll@gmx.de>
Link: https://lore.kernel.org/r/AM0PR09MB26758F651BC1B742EB45775995B8A@AM0PR09MB2675.eurprd09.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

serial: imx: Ensure that imx_uart_rs485_config() is called with enabled clock

commit 7c45eaa813476bd195ac1227a64b52f9cf2e2030 upstream.

There are register accesses in the function imx_uart_rs485_co

serial: imx: Ensure that imx_uart_rs485_config() is called with enabled clock

commit 7c45eaa813476bd195ac1227a64b52f9cf2e2030 upstream.

There are register accesses in the function imx_uart_rs485_config(). The
clock must be enabled for these accesses. This was ensured by calling it
via the function uart_rs485_config() in the probe() function within the
range where the clock is enabled. With the commit 7c7f9bc986e6 ("serial:
Deassert Transmit Enable on probe in driver-specific way") it was removed
from the probe() function and is now only called through the function
uart_add_one_port() which is located at the end of the probe() function.
But the clock is already switched off in this area. To ensure that the
clock is enabled during register access, move the disabling of the clock
to the very end of the probe() function. To avoid leaking enabled clocks
on error also add an error path for exiting with disabling the clock.

Fixes: 7c7f9bc986e6 ("serial: Deassert Transmit Enable on probe in driver-specific way")
Cc: stable <stable@kernel.org>
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/20231226113647.39376-1-cniedermaier@dh-electronics.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

serial: core, imx: do not set RS485 enabled if it is not supported

commit 74eab89b26ac433ad857292f4707b43c1a8f0209 upstream.

If the imx driver cannot support RS485 it nullifies the ports
rs485_supp

serial: core, imx: do not set RS485 enabled if it is not supported

commit 74eab89b26ac433ad857292f4707b43c1a8f0209 upstream.

If the imx driver cannot support RS485 it nullifies the ports
rs485_supported structure. But it still calls uart_get_rs485_mode() which
may set the RS485_ENABLED flag nevertheless.

This may lead to an attempt to configure RS485 even if it is not supported
when the flag is evaluated in uart_configure_port() at port startup.

Avoid this by bailing out of uart_get_rs485_mode() if the RS485_ENABLED
flag is not supported by the caller.

With this fix a check for RTS availability is now obsolete in the imx
driver, since it can not evaluate to true any more. So remove this check.

Furthermore the explicit nullifcation of rs485_supported is not needed,
since the memory has already been set to zeros at allocation. So remove
this, too.

Fixes: 00d7a00e2a6f ("serial: imx: Fill in rs485_supported")
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: <stable@vger.kernel.org>
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240103061818.564-6-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

Merge drm/drm-fixes into drm-misc-fixes

Forwarding to v6.6-rc1.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>

Merge tag 'tty-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty

Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.6-rc1.

Merge tag 'tty-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty

Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.6-rc1.

Lots of cleanups in here this cycle, and some driver updates. Short
summary is:

- Jiri's continued work to make the tty code and apis be a bit more
sane with regards to modern kernel coding style and types

- cpm_uart driver updates

- n_gsm updates and fixes

- meson driver updates

- sc16is7xx driver updates

- 8250 driver updates for different hardware types

- qcom-geni driver fixes

- tegra serial driver change

- stm32 driver updates

- synclink_gt driver cleanups

- tty structure size reduction

All of these have been in linux-next this week with no reported
issues. The last bit of cleanups from Jiri and the tty structure size
reduction came in last week, a bit late but as they were just style
changes and size reductions, I figured they should get into this merge
cycle so that others can work on top of them with no merge conflicts"

* tag 'tty-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (199 commits)
tty: shrink the size of struct tty_struct by 40 bytes
tty: n_tty: deduplicate copy code in n_tty_receive_buf_real_raw()
tty: n_tty: extract ECHO_OP processing to a separate function
tty: n_tty: unify counts to size_t
tty: n_tty: use u8 for chars and flags
tty: n_tty: simplify chars_in_buffer()
tty: n_tty: remove unsigned char casts from character constants
tty: n_tty: move newline handling to a separate function
tty: n_tty: move canon handling to a separate function
tty: n_tty: use MASK() for masking out size bits
tty: n_tty: make n_tty_data::num_overrun unsigned
tty: n_tty: use time_is_before_jiffies() in n_tty_receive_overrun()
tty: n_tty: use 'num' for writes' counts
tty: n_tty: use output character directly
tty: n_tty: make flow of n_tty_receive_buf_common() a bool
Revert "tty: serial: meson: Add a earlycon for the T7 SoC"
Documentation: devices.txt: Fix minors for ttyCPM*
Documentation: devices.txt: Remove ttySIOC*
Documentation: devices.txt: Remove ttyIOC*
serial: 8250_bcm7271: improve bcm7271 8250 port
...

show more ...

Merge branch 'next' into for-linus

Prepare input updates for 6.6 merge window.

Merge drm/drm-next into drm-intel-next

Catching-up with drm-next and drm-intel-gt-next.
It will unblock a code refactor around the platform
definitions (names vs acronyms).

Signed-off-by: Rodrigo V

Merge drm/drm-next into drm-intel-next

Catching-up with drm-next and drm-intel-gt-next.
It will unblock a code refactor around the platform
definitions (names vs acronyms).

Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

show more ...

Merge drm/drm-next into drm-intel-gt-next

Need to pull in b3e4aae612ec ("drm/i915/hdcp: Modify hdcp_gsc_message msg sending mechanism") as
a dependency for https://patchwork.freedesktop.org/series/1

Merge drm/drm-next into drm-intel-gt-next

Need to pull in b3e4aae612ec ("drm/i915/hdcp: Modify hdcp_gsc_message msg sending mechanism") as
a dependency for https://patchwork.freedesktop.org/series/121735/

Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

show more ...

serial: imx: Use devm_platform_get_and_ioremap_resource()

Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
wh

serial: imx: Use devm_platform_get_and_ioremap_resource()

Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.

Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230712062853.11007-14-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

tty: Explicitly include correct DT includes

The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that mer

tty: Explicitly include correct DT includes

The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.

Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> # for imx
Link: https://lore.kernel.org/r/20230724205440.767071-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...