| 0f7bdcbb | 17-Feb-2024 |
Alexis Lothoré <alexis.lothore@bootlin.com> |
wifi: wilc1000: revert reset line logic flip
[ Upstream commit f3ec643947634bed41b97bd56b248f7c78498eab ]
This reverts commit fcf690b0b47494df51d214db5c5a714a400b0257.
When using a wilc1000 chip o
wifi: wilc1000: revert reset line logic flip
[ Upstream commit f3ec643947634bed41b97bd56b248f7c78498eab ]
This reverts commit fcf690b0b47494df51d214db5c5a714a400b0257.
When using a wilc1000 chip over a spi bus, users can optionally define a
reset gpio and a chip enable gpio. The reset line of wilc1000 is active
low, so to hold the chip in reset, a low (physical) value must be applied.
The corresponding device tree binding documentation was introduced by
commit f31ee3c0a555 ("wilc1000: Document enable-gpios and reset-gpios
properties") and correctly indicates that the reset line is an active-low
signal. The corresponding driver part, brought by commit ec031ac4792c
("wilc1000: Add reset/enable GPIO support to SPI driver") was applying the
correct logic. But commit fcf690b0b474 ("wifi: wilc1000: use correct
sequence of RESET for chip Power-UP/Down") eventually flipped this logic
and started misusing the gpiod APIs, applying an inverted logic when
powering up/down the chip (for example, setting the reset line to a logic
"1" during power up, which in fact asserts the reset line when device tree
describes the reset line as GPIO_ACTIVE_LOW). As a consequence, any
platform currently using the driver in SPI mode must use a faulty reset
line description in device tree, or else chip will be maintained in reset
and will not even allow to bring up the chip.
Fix reset line usage by inverting back the gpiod APIs usage, setting the
reset line to the logic value "0" when powering the chip, and the logic
value "1" when powering off the chip.
Fixes: fcf690b0b474 ("wifi: wilc1000: use correct sequence of RESET for chip Power-UP/Down")
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240217-wilc_1000_reset_line-v2-1-b216f433d7d5@bootlin.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
show more ...
|
| 3da9d32b | 12-Feb-2024 |
Alexis Lothoré <alexis.lothore@bootlin.com> |
wifi: wilc1000: prevent use-after-free on vif when cleaning up all interfaces
[ Upstream commit cb5942b77c05d54310a0420cac12935e9b6aa21c ]
wilc_netdev_cleanup currently triggers a KASAN warning, wh
wifi: wilc1000: prevent use-after-free on vif when cleaning up all interfaces
[ Upstream commit cb5942b77c05d54310a0420cac12935e9b6aa21c ]
wilc_netdev_cleanup currently triggers a KASAN warning, which can be
observed on interface registration error path, or simply by
removing the module/unbinding device from driver:
echo spi0.1 > /sys/bus/spi/drivers/wilc1000_spi/unbind
==================================================================
BUG: KASAN: slab-use-after-free in wilc_netdev_cleanup+0x508/0x5cc
Read of size 4 at addr c54d1ce8 by task sh/86
CPU: 0 PID: 86 Comm: sh Not tainted 6.8.0-rc1+ #117
Hardware name: Atmel SAMA5
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x34/0x58
dump_stack_lvl from print_report+0x154/0x500
print_report from kasan_report+0xac/0xd8
kasan_report from wilc_netdev_cleanup+0x508/0x5cc
wilc_netdev_cleanup from wilc_bus_remove+0xc8/0xec
wilc_bus_remove from spi_remove+0x8c/0xac
spi_remove from device_release_driver_internal+0x434/0x5f8
device_release_driver_internal from unbind_store+0xbc/0x108
unbind_store from kernfs_fop_write_iter+0x398/0x584
kernfs_fop_write_iter from vfs_write+0x728/0xf88
vfs_write from ksys_write+0x110/0x1e4
ksys_write from ret_fast_syscall+0x0/0x1c
[...]
Allocated by task 1:
kasan_save_track+0x30/0x5c
__kasan_kmalloc+0x8c/0x94
__kmalloc_node+0x1cc/0x3e4
kvmalloc_node+0x48/0x180
alloc_netdev_mqs+0x68/0x11dc
alloc_etherdev_mqs+0x28/0x34
wilc_netdev_ifc_init+0x34/0x8ec
wilc_cfg80211_init+0x690/0x910
wilc_bus_probe+0xe0/0x4a0
spi_probe+0x158/0x1b0
really_probe+0x270/0xdf4
__driver_probe_device+0x1dc/0x580
driver_probe_device+0x60/0x140
__driver_attach+0x228/0x5d4
bus_for_each_dev+0x13c/0x1a8
bus_add_driver+0x2a0/0x608
driver_register+0x24c/0x578
do_one_initcall+0x180/0x310
kernel_init_freeable+0x424/0x484
kernel_init+0x20/0x148
ret_from_fork+0x14/0x28
Freed by task 86:
kasan_save_track+0x30/0x5c
kasan_save_free_info+0x38/0x58
__kasan_slab_free+0xe4/0x140
kfree+0xb0/0x238
device_release+0xc0/0x2a8
kobject_put+0x1d4/0x46c
netdev_run_todo+0x8fc/0x11d0
wilc_netdev_cleanup+0x1e4/0x5cc
wilc_bus_remove+0xc8/0xec
spi_remove+0x8c/0xac
device_release_driver_internal+0x434/0x5f8
unbind_store+0xbc/0x108
kernfs_fop_write_iter+0x398/0x584
vfs_write+0x728/0xf88
ksys_write+0x110/0x1e4
ret_fast_syscall+0x0/0x1c
[...]
David Mosberger-Tan initial investigation [1] showed that this
use-after-free is due to netdevice unregistration during vif list
traversal. When unregistering a net device, since the needs_free_netdev has
been set to true during registration, the netdevice object is also freed,
and as a consequence, the corresponding vif object too, since it is
attached to it as private netdevice data. The next occurrence of the loop
then tries to access freed vif pointer to the list to move forward in the
list.
Fix this use-after-free thanks to two mechanisms:
- navigate in the list with list_for_each_entry_safe, which allows to
safely modify the list as we go through each element. For each element,
remove it from the list with list_del_rcu
- make sure to wait for RCU grace period end after each vif removal to make
sure it is safe to free the corresponding vif too (through
unregister_netdev)
Since we are in a RCU "modifier" path (not a "reader" path), and because
such path is expected not to be concurrent to any other modifier (we are
using the vif_mutex lock), we do not need to use RCU list API, that's why
we can benefit from list_for_each_entry_safe.
[1] https://lore.kernel.org/linux-wireless/ab077dbe58b1ea5de0a3b2ca21f275a07af967d2.camel@egauge.net/
Fixes: 8399918f3056 ("staging: wilc1000: use RCU list to maintain vif interfaces list")
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240212-wilc_rework_deinit-v1-1-9203ae56c27f@bootlin.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
show more ...
|
| b66b008f | 15-Jan-2024 |
Ajay Singh <ajay.kathat@microchip.com> |
wifi: wilc1000: fix multi-vif management when deleting a vif
[ Upstream commit 12cfc9c8d3faf887a202c89bc312202445fca7e8 ]
Adding then removing a second vif currently makes the first vif not working
wifi: wilc1000: fix multi-vif management when deleting a vif
[ Upstream commit 12cfc9c8d3faf887a202c89bc312202445fca7e8 ]
Adding then removing a second vif currently makes the first vif not working
anymore. This is visible for example when we have a first interface
connected to some access point:
- create a wpa_supplicant.conf with some AP credentials
- wpa_supplicant -Dnl80211 -c /etc/wpa_supplicant.conf -i wlan0
- dhclient wlan0
- iw phy phy0 interface add wlan1 type managed
- iw dev wlan1 del
wlan0 does not manage properly traffic anymore (eg: ping not working)
This is due to vif mode being incorrectly reconfigured with some default
values in del_virtual_intf, affecting by default first vif.
Prevent first vif from being affected on second vif removal by removing vif
mode change command in del_virtual_intf
Fixes: 9bc061e88054 ("staging: wilc1000: added support to dynamically add/remove interfaces")
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Co-developed-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240115-wilc_1000_fixes-v1-5-54d29463a738@bootlin.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
show more ...
|
| 4041c60a | 15-Jan-2024 |
Ajay Singh <ajay.kathat@microchip.com> |
wifi: wilc1000: do not realloc workqueue everytime an interface is added
[ Upstream commit 328efda22af81130c2ad981c110518cb29ff2f1d ]
Commit 09ed8bfc5215 ("wilc1000: Rename workqueue from "WILC_wq"
wifi: wilc1000: do not realloc workqueue everytime an interface is added
[ Upstream commit 328efda22af81130c2ad981c110518cb29ff2f1d ]
Commit 09ed8bfc5215 ("wilc1000: Rename workqueue from "WILC_wq" to
"NETDEV-wq"") moved workqueue creation in wilc_netdev_ifc_init in order to
set the interface name in the workqueue name. However, while the driver
needs only one workqueue, the wilc_netdev_ifc_init is called each time we
add an interface over a phy, which in turns overwrite the workqueue with a
new one. This can be observed with the following commands:
for i in $(seq 0 10)
do
iw phy phy0 interface add wlan1 type managed
iw dev wlan1 del
done
ps -eo pid,comm|grep wlan
39 kworker/R-wlan0
98 kworker/R-wlan1
102 kworker/R-wlan1
105 kworker/R-wlan1
108 kworker/R-wlan1
111 kworker/R-wlan1
114 kworker/R-wlan1
117 kworker/R-wlan1
120 kworker/R-wlan1
123 kworker/R-wlan1
126 kworker/R-wlan1
129 kworker/R-wlan1
Fix this leakage by putting back hif_workqueue allocation in
wilc_cfg80211_init. Regarding the workqueue name, it is indeed relevant to
set it lowercase, however it is not attached to a specific netdev, so
enforcing netdev name in the name is not so relevant. Still, enrich the
name with the wiphy name to make it clear which phy is using the workqueue.
Fixes: 09ed8bfc5215 ("wilc1000: Rename workqueue from "WILC_wq" to "NETDEV-wq"")
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Co-developed-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240115-wilc_1000_fixes-v1-3-54d29463a738@bootlin.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
show more ...
|
| 4bfd20d5 | 05-Jan-2024 |
Alexis Lothoré <alexis.lothore@bootlin.com> |
wifi: wilc1000: fix RCU usage in connect path
[ Upstream commit 205c50306acf58a335eb19fa84e40140f4fe814f ]
With lockdep enabled, calls to the connect function from cfg802.11 layer
lead to the follo
wifi: wilc1000: fix RCU usage in connect path
[ Upstream commit 205c50306acf58a335eb19fa84e40140f4fe814f ]
With lockdep enabled, calls to the connect function from cfg802.11 layer
lead to the following warning:
=============================
WARNING: suspicious RCU usage
6.7.0-rc1-wt+ #333 Not tainted
-----------------------------
drivers/net/wireless/microchip/wilc1000/hif.c:386
suspicious rcu_dereference_check() usage!
[...]
stack backtrace:
CPU: 0 PID: 100 Comm: wpa_supplicant Not tainted 6.7.0-rc1-wt+ #333
Hardware name: Atmel SAMA5
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x34/0x48
dump_stack_lvl from wilc_parse_join_bss_param+0x7dc/0x7f4
wilc_parse_join_bss_param from connect+0x2c4/0x648
connect from cfg80211_connect+0x30c/0xb74
cfg80211_connect from nl80211_connect+0x860/0xa94
nl80211_connect from genl_rcv_msg+0x3fc/0x59c
genl_rcv_msg from netlink_rcv_skb+0xd0/0x1f8
netlink_rcv_skb from genl_rcv+0x2c/0x3c
genl_rcv from netlink_unicast+0x3b0/0x550
netlink_unicast from netlink_sendmsg+0x368/0x688
netlink_sendmsg from ____sys_sendmsg+0x190/0x430
____sys_sendmsg from ___sys_sendmsg+0x110/0x158
___sys_sendmsg from sys_sendmsg+0xe8/0x150
sys_sendmsg from ret_fast_syscall+0x0/0x1c
This warning is emitted because in the connect path, when trying to parse
target BSS parameters, we dereference a RCU pointer whithout being in RCU
critical section.
Fix RCU dereference usage by moving it to a RCU read critical section. To
avoid wrapping the whole wilc_parse_join_bss_param under the critical
section, just use the critical section to copy ies data
Fixes: c460495ee072 ("staging: wilc1000: fix incorrent type in initializer")
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240105075733.36331-3-alexis.lothore@bootlin.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
show more ...
|
| 6fd879f9 | 24-Jul-2023 |
Amisha Patel <amisha.patel@microchip.com> |
wifi: wilc1000: add SPI commands retry mechanism
In some situations like, chip wake-up with powersave enabled, SPI
commands are failing temporarily. Reissuing commands after reset helps
to overcome
wifi: wilc1000: add SPI commands retry mechanism
In some situations like, chip wake-up with powersave enabled, SPI
commands are failing temporarily. Reissuing commands after reset helps
to overcome the failure. So, add the retry limit and reset command
sequence API for read/write SPI commands.
Signed-off-by: Amisha Patel <amisha.patel@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230724163955.4583-1-amisha.patel@microchip.com
show more ...
|
| 7acd6950 | 09-May-2023 |
Amisha Patel <amisha.patel@microchip.com> |
wifi: wilc1000: Increase ASSOC response buffer
In recent access points, information element is longer as they include
additional data which exceeds 256 bytes. To accommodate longer
association respo
wifi: wilc1000: Increase ASSOC response buffer
In recent access points, information element is longer as they include
additional data which exceeds 256 bytes. To accommodate longer
association response, increase the ASSOC response buffer.
Signed-off-by: Amisha Patel <amisha.patel@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230509172811.4953-1-amisha.patel@microchip.com
show more ...
|
| 2b88974e | 24-Nov-2022 |
Wang Yufen <wangyufen@huawei.com> |
wifi: wilc1000: add missing unregister_netdev() in wilc_netdev_ifc_init()
Fault injection test reports this issue:
kernel BUG at net/core/dev.c:10731!
invalid opcode: 0000 [#1] PREEMPT SMP KASAN PT
wifi: wilc1000: add missing unregister_netdev() in wilc_netdev_ifc_init()
Fault injection test reports this issue:
kernel BUG at net/core/dev.c:10731!
invalid opcode: 0000 [#1] PREEMPT SMP KASAN PTI
Call Trace:
<TASK>
wilc_netdev_ifc_init+0x19f/0x220 [wilc1000 884bf126e9e98af6a708f266a8dffd53f99e4bf5]
wilc_cfg80211_init+0x30c/0x380 [wilc1000 884bf126e9e98af6a708f266a8dffd53f99e4bf5]
wilc_bus_probe+0xad/0x2b0 [wilc1000_spi 1520a7539b6589cc6cde2ae826a523a33f8bacff]
spi_probe+0xe4/0x140
really_probe+0x17e/0x3f0
__driver_probe_device+0xe3/0x170
driver_probe_device+0x49/0x120
The root case here is alloc_ordered_workqueue() fails, but
cfg80211_unregister_netdevice() or unregister_netdev() not be called in
error handling path. To fix add unregister_netdev goto lable to add the
unregister operation in error handling path.
Fixes: 09ed8bfc5215 ("wilc1000: Rename workqueue from "WILC_wq" to "NETDEV-wq"")
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/1669289902-23639-1-git-send-email-wangyufen@huawei.com
show more ...
|
| 0cdfa9e6 | 23-Nov-2022 |
Phil Turnbull <philipturnbull@github.com> |
wifi: wilc1000: validate number of channels
There is no validation of 'e->no_of_channels' which can trigger an
out-of-bounds write in the following 'memset' call. Validate that the
number of channel
wifi: wilc1000: validate number of channels
There is no validation of 'e->no_of_channels' which can trigger an
out-of-bounds write in the following 'memset' call. Validate that the
number of channels does not extends beyond the size of the channel list
element.
Signed-off-by: Phil Turnbull <philipturnbull@github.com>
Tested-by: Ajay Kathat <ajay.kathat@microchip.com>
Acked-by: Ajay Kathat <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221123153543.8568-5-philipturnbull@github.com
show more ...
|
| f9b62f98 | 23-Nov-2022 |
Phil Turnbull <philipturnbull@github.com> |
wifi: wilc1000: validate length of IEEE80211_P2P_ATTR_CHANNEL_LIST attribute
Validate that the IEEE80211_P2P_ATTR_CHANNEL_LIST attribute contains
enough space for a 'struct wilc_attr_oper_ch'. If th
wifi: wilc1000: validate length of IEEE80211_P2P_ATTR_CHANNEL_LIST attribute
Validate that the IEEE80211_P2P_ATTR_CHANNEL_LIST attribute contains
enough space for a 'struct wilc_attr_oper_ch'. If the attribute is too
small then it can trigger an out-of-bounds write later in the function.
'struct wilc_attr_oper_ch' is variable sized so also check 'attr_len'
does not extend beyond the end of 'buf'.
Signed-off-by: Phil Turnbull <philipturnbull@github.com>
Tested-by: Ajay Kathat <ajay.kathat@microchip.com>
Acked-by: Ajay Kathat <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221123153543.8568-4-philipturnbull@github.com
show more ...
|
| 051ae669 | 23-Nov-2022 |
Phil Turnbull <philipturnbull@github.com> |
wifi: wilc1000: validate length of IEEE80211_P2P_ATTR_OPER_CHANNEL attribute
Validate that the IEEE80211_P2P_ATTR_OPER_CHANNEL attribute contains
enough space for a 'struct struct wilc_attr_oper_ch'
wifi: wilc1000: validate length of IEEE80211_P2P_ATTR_OPER_CHANNEL attribute
Validate that the IEEE80211_P2P_ATTR_OPER_CHANNEL attribute contains
enough space for a 'struct struct wilc_attr_oper_ch'. If the attribute is
too small then it triggers an out-of-bounds write later in the function.
Signed-off-by: Phil Turnbull <philipturnbull@github.com>
Tested-by: Ajay Kathat <ajay.kathat@microchip.com>
Acked-by: Ajay Kathat <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221123153543.8568-3-philipturnbull@github.com
show more ...
|