/openbmc/linux/Documentation/devicetree/bindings/iio/pressure/ |
H A D | hoperf,hp03.yaml | 24 The XCLR pin is a reset of the ADC in the chip, it must be pulled 26 registers and pulled LO afterward.
|
/openbmc/linux/Documentation/devicetree/bindings/sound/ |
H A D | everest,es7241.txt | 15 the sdout. If the sdout is pulled down, leftj format is used. 16 If this property is not provided, sdout is assumed to pulled
|
/openbmc/linux/arch/arm64/boot/dts/freescale/ |
H A D | imx8mm-venice-gw72xx-0x-rs485.dtso | 10 * - RS485_EN needs to be pulled high 11 * - RS485_HALF needs to be pulled high
|
H A D | imx8mm-venice-gw73xx-0x-rs485.dtso | 10 * - RS485_EN needs to be pulled high 11 * - RS485_HALF needs to be pulled high
|
H A D | imx8mm-venice-gw72xx-0x-rs422.dtso | 10 * - RS485_EN needs to be pulled high
|
H A D | imx8mm-venice-gw73xx-0x-rs422.dtso | 10 * - RS485_EN needs to be pulled high
|
/openbmc/linux/Documentation/devicetree/bindings/iio/light/ |
H A D | veml6030.yaml | 34 - 0x10 # ADDR pin pulled down 35 - 0x48 # ADDR pin pulled up
|
/openbmc/openbmc/poky/meta/recipes-kernel/lttng/lttng-modules/ |
H A D | 0001-src-Kbuild-change-missing-CONFIG_TRACEPOINTS-to-warn.patch | 9 The lttng-modules are being pulled by the tools-profile image feature, 13 available, allowing it to be kept being pulled by default.
|
/openbmc/linux/drivers/net/ethernet/intel/fm10k/ |
H A D | fm10k_mbx.c | 349 end = fm10k_fifo_head_offset(fifo, mbx->pulled); in fm10k_mbx_write_copy() 389 mbx->pulled += mbx->tail_len - ack; in fm10k_mbx_pull_head() 393 len = fm10k_fifo_used(fifo) - mbx->pulled; in fm10k_mbx_pull_head() 403 len && (mbx->pulled >= len); in fm10k_mbx_pull_head() 405 mbx->pulled -= fm10k_fifo_head_drop(fifo); in fm10k_mbx_pull_head() 622 head = fm10k_fifo_head_offset(&mbx->tx, mbx->pulled); in fm10k_mbx_update_local_crc() 1068 mbx->pulled += mbx->tail_len - ack; in fm10k_mbx_reset_work() 1074 if (mbx->pulled >= len) in fm10k_mbx_reset_work() 1075 mbx->pulled -= len; in fm10k_mbx_reset_work() 1077 mbx->pulled = 0; in fm10k_mbx_reset_work() [all …]
|
H A D | fm10k_mbx.h | 266 u16 tail, tail_len, pulled; member
|
/openbmc/openbmc/poky/meta/recipes-core/glibc/ldconfig-native-2.12.1/ |
H A D | README | 1 The files are pulled verbatim from glibc 2.5 and then patched to allow
|
/openbmc/qemu/tests/decode/ |
H A D | succ_function.decode | 4 # "Field" as parameter pulled from DisasContext.
|
/openbmc/linux/Documentation/devicetree/bindings/gpio/ |
H A D | gpio-max3191x.txt | 31 pulled high (8-bit mode). Use this if the modesel pin 35 that modesel is pulled low (16-bit mode).
|
/openbmc/linux/Documentation/dev-tools/ |
H A D | index.rst | 6 be used to work on the kernel. For now, the documents have been pulled
|
/openbmc/openbmc/meta-openembedded/meta-oe/recipes-connectivity/ifplugd/ |
H A D | ifplugd_0.28.bb | 2 when a cable is plugged in and automatically unconfigure it if the cable is pulled."
|
/openbmc/linux/arch/powerpc/boot/dts/fsl/ |
H A D | p1023rdb.dts | 186 /* IRQ[0:3] are pulled up on board, set to active-low */ 212 * IRQ[7] is pulled up on board, set to active-low 238 * IRQ[8:10] are pulled up on board, set to active-low
|
/openbmc/linux/Documentation/devicetree/bindings/iio/dac/ |
H A D | ti,dac7612.yaml | 29 DACs are loaded when the pin connected to this GPIO is pulled low.
|
/openbmc/linux/Documentation/devicetree/bindings/extcon/ |
H A D | qcom,pm8941-misc.yaml | 14 the USB ID pin has been pulled low or high.
|
/openbmc/linux/Documentation/devicetree/bindings/mfd/ |
H A D | samsung,s2mps11.yaml | 49 power. Usually the ACOKB is pulled up to VBATT so when PWRHOLD pin goes 55 Indicates that WRSTBI pin of PMIC is pulled down. When the system is
|
/openbmc/linux/Documentation/devicetree/bindings/usb/ |
H A D | samsung,exynos-usb2.yaml | 44 needs to be pulled up for the bus to be powered.
|
/openbmc/linux/arch/arm64/boot/dts/qcom/ |
H A D | sdm845-db845c-navigation-mezzanine.dts | 87 * vreg_s4a_1p8 trace is pulled high.
|
/openbmc/openbmc/meta-openembedded/meta-networking/recipes-support/linux-atm/linux-atm/ |
H A D | 0001-saaldump-atmdump-Include-linux-sockios.h-for-SIOCGST.patch | 12 header file is not pulled so we get a build failure.
|
/openbmc/linux/Documentation/devicetree/bindings/leds/ |
H A D | kinetic,ktd2692.yaml | 20 Also, When the AUX pin is pulled high while CTRL pin is high,
|
/openbmc/linux/arch/arm/boot/dts/allwinner/ |
H A D | sunxi-d1s-t113-mangopi-mq-r.dtsi | 117 /* The USB-C socket has its CC pins pulled to GND, so is hardwired as a UFP. */
|
/openbmc/linux/arch/arm/boot/dts/intel/pxa/ |
H A D | pxa3xx.dtsi | 88 * the configured driven and pulled levels match, so if there is a need for 89 * non-LPM pulled output, the same configuration could probably be used.
|