/openbmc/linux/Documentation/ABI/testing/ |
H A D | sysfs-class-chromeos | 27 - "at-shutdown": Reboot after an AP shutdown.
|
H A D | debugfs-cros-ec | 32 is used for synchronizing the AP host time with the EC 45 the most recent response from the AP's resume message to the EC.
|
/openbmc/linux/arch/arm/boot/dts/qcom/ |
H A D | qcom-ipq4019-ap.dk07.1.dtsi | 9 model = "Qualcomm Technologies, Inc. IPQ4019/AP-DK07.1";
|
H A D | qcom-ipq4019-ap.dk01.1-c1.dts | 20 model = "Qualcomm Technologies, Inc. IPQ40xx/AP-DK01.1-C1";
|
H A D | qcom-ipq4019-ap.dk04.1.dtsi | 9 model = "Qualcomm Technologies, Inc. IPQ4019/AP-DK04.1";
|
/openbmc/linux/Documentation/networking/mac80211_hwsim/ |
H A D | mac80211_hwsim.rst | 59 associates with the AP. hostapd and wpa_supplicant are used to take 71 # Run hostapd (AP) for wlan0
|
/openbmc/linux/arch/arm64/boot/dts/qcom/ |
H A D | ipq6018-cp01-c1.dts | 13 model = "Qualcomm Technologies, Inc. IPQ6018/AP-CP01-C1";
|
H A D | ipq9574-rdp453.dts | 14 model = "Qualcomm Technologies, Inc. IPQ9574/AP-AL02-C8";
|
H A D | ipq9574-rdp454.dts | 14 model = "Qualcomm Technologies, Inc. IPQ9574/AP-AL02-C9";
|
H A D | ipq9574-rdp449.dts | 14 model = "Qualcomm Technologies, Inc. IPQ9574/AP-AL02-C6";
|
/openbmc/u-boot/arch/arm/dts/ |
H A D | rk3399-gru-chromebook.dtsi | 15 /* EC turns on w/ pp900_ap_en; always on for AP */ 58 /* EC turns on w/ ppvar_centerlogic_en; always on for AP */ 85 /* EC turns on w/ ppvar_logic_en; always on for AP */
|
H A D | exynos4210-universal_c210.dts | 212 ap32khz_reg: EN32KHz-AP { 213 regulator-name = "32KHz AP";
|
/openbmc/linux/drivers/firmware/imx/ |
H A D | Kconfig | 6 This enables DSP IPC protocol between host AP (Linux)
|
/openbmc/linux/Documentation/devicetree/bindings/arm/mediatek/ |
H A D | mediatek,mt8186-sys-clock.yaml | 23 The mcusys provides mux control to select the clock source in AP MCU.
|
/openbmc/linux/Documentation/devicetree/bindings/clock/ |
H A D | mediatek,apmixedsys.yaml | 7 title: MediaTek AP Mixedsys Controller
|
H A D | mediatek,mt8188-sys-clock.yaml | 23 The mcusys provides mux control to select the clock source in AP MCU.
|
/openbmc/linux/arch/arm/boot/dts/broadcom/ |
H A D | bcm28155-ap.dts | 11 model = "BCM28155 AP board";
|
/openbmc/qemu/docs/specs/ |
H A D | sev-guest-firmware.rst | 61 | 0xffffffb8 | 4 | SEV-ES AP reset RIP | 90 For the initial boot of an AP under SEV-ES, the "reset" RIP must be
|
/openbmc/u-boot/doc/mvebu/ |
H A D | armada-8k-memory.txt | 15 0xF0000000 0xF0FFFFFF AP Internal registers space
|
/openbmc/u-boot/board/armltd/integrator/ |
H A D | README | 13 There are two Integrator variants - Integrator/AP and Integrator/CP. 68 Integrator/AP is no longer available from ARM.
|
/openbmc/linux/arch/arm/boot/dts/arm/ |
H A D | integratorap-im-pd1.dts | 3 * Device Tree for the ARM Integrator/AP platform 10 model = "ARM Integrator/AP with IM-PD1";
|
/openbmc/linux/Documentation/devicetree/bindings/reset/ |
H A D | zynq-reset.txt | 3 The Zynq AP-SoC has several different resets.
|
/openbmc/linux/arch/arm/boot/dts/marvell/ |
H A D | armada-388-rd.dts | 4 * (RD-88F6820-AP)
|
/openbmc/linux/drivers/net/wireless/marvell/mwifiex/ |
H A D | README | 46 The above command can be used to connect to an AP with a particular SSID. 47 Ap's operating frequency can be specified or even the bssid. If the AP is using 49 …Note: Every time before connecting to an AP scan command (iw dev mlan0 scan) should be used by use… 52 This command will be used to disconnect from an AP.
|
/openbmc/linux/Documentation/devicetree/bindings/remoteproc/ |
H A D | qcom,pas-common.yaml | 57 description: States used by the AP to signal the Hexagon core
|