arm64: dts: ti: k3-j721e: Enable C6x DSP nodes at the board level

C6x DSP nodes defined in the top-level J721e SoC dtsi files are incomplete
and will not be functional unless they are extended with

arm64: dts: ti: k3-j721e: Enable C6x DSP nodes at the board level

C6x DSP nodes defined in the top-level J721e SoC dtsi files are incomplete
and will not be functional unless they are extended with both mboxes and
memory-region information.

As theses only known about at the board integration level, these nodes
should only be enabled when provided with this information.

Disable the C6x DSP nodes in the dtsi files and only enable the ones that
are given the required mboxes and memory-region on a given board.

Signed-off-by: Andrew Davis <afd@ti.com>
Acked-by: Hari Nagalla <hnagalla@ti.com>
Tested-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20230809180145.53158-3-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>

show more ...

arm64: dts: ti: k3-j721e: Enable C7x DSP nodes at the board level

C7x DSP nodes defined in the top-level J721e SoC dtsi files are incomplete
and will not be functional unless they are extended with

arm64: dts: ti: k3-j721e: Enable C7x DSP nodes at the board level

C7x DSP nodes defined in the top-level J721e SoC dtsi files are incomplete
and will not be functional unless they are extended with both mboxes and
memory-region information.

As theses only known about at the board integration level, these nodes
should only be enabled when provided with this information.

Disable the C7x DSP nodes in the dtsi files and only enable the ones that
are given the required mboxes and memory-region on a given board.

Signed-off-by: Andrew Davis <afd@ti.com>
Acked-by: Hari Nagalla <hnagalla@ti.com>
Tested-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20230809180145.53158-1-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>

show more ...

arm64: dts: ti: k3-j721e: Enable GPIO nodes at the board level

GPIO nodes defined in the top-level J721e SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux

arm64: dts: ti: k3-j721e: Enable GPIO nodes at the board level

GPIO nodes defined in the top-level J721e SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux and
device information.

Disable the GPIO nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.

Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230810003814.85450-9-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>

show more ...

arm64: dts: ti: k3-j721e: Enable SDHCI nodes at the board level

SDHCI nodes defined in the top-level J721e SoC dtsi files are incomplete
and will not be functional unless they are extended.

As the

arm64: dts: ti: k3-j721e: Enable SDHCI nodes at the board level

SDHCI nodes defined in the top-level J721e SoC dtsi files are incomplete
and will not be functional unless they are extended.

As the attached SD/eMMC is only known about at the board integration level,
these nodes should only be enabled when provided with this information.

Disable the SDHCI nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.

Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230810003814.85450-2-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>

show more ...

arm64: dts: ti: k3: Add cfg reg region to ringacc node

Add register range of ringacc cfg node to all k3 SoC dtsi files. This is
normally under Device Management firmware control but some entities li

arm64: dts: ti: k3: Add cfg reg region to ringacc node

Add register range of ringacc cfg node to all k3 SoC dtsi files. This is
normally under Device Management firmware control but some entities like
bootloader have to access directly and thus required to be present in DT.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20230809175932.2553156-3-vigneshr@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>

show more ...

arm64: dts: ti: Use local header for SERDES MUX idle-state values

The DTS uses constants for SERDES MUX idle state values which were earlier
provided as bindings header. But they are unsuitable for

arm64: dts: ti: Use local header for SERDES MUX idle-state values

The DTS uses constants for SERDES MUX idle state values which were earlier
provided as bindings header. But they are unsuitable for bindings.
So move these constants in a header next to DTS.

Also add J784S4 SERDES4 lane definitions which were missed earlier.

Suggested-by: Nishanth Menon <nm@ti.com>
Suggested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Suggested-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/linux-arm-kernel/b24c2124-fe3b-246c-9af9-3ecee9fb32d4@kernel.org/
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Peter Rosin <peda@axentia.se>
Link: https://lore.kernel.org/r/20230721125732.122421-2-j-choudhary@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>

show more ...

arm64: dts: ti: Fix compatible of ti,*-ehrpwm-tbclk

TI EHRPWM compatible is just ti,*-ehrpwm-tbclk without needing a
syscon compatibility.

Fixes the following dtbs_check warnings:
compatible: [''t

arm64: dts: ti: Fix compatible of ti,*-ehrpwm-tbclk

TI EHRPWM compatible is just ti,*-ehrpwm-tbclk without needing a
syscon compatibility.

Fixes the following dtbs_check warnings:
compatible: [''ti,am654-ehrpwm-tbclk, 'syscon'] is too long
compatible: ['ti,am64-epwm-tbclk', 'syscon'] is too long
compatible: ['ti,am62-epwm-tbclk', 'syscon'] is too long

Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20230713184759.3336536-1-nm@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>

show more ...

arm64: dts: ti: add missing space before {

Add missing whitespace between node name/label and opening {.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: David Lechn

arm64: dts: ti: add missing space before {

Add missing whitespace between node name/label and opening {.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: David Lechner <david@lechnology.com>
Link: https://lore.kernel.org/r/20230705145755.292927-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Nishanth Menon <nm@ti.com>

show more ...

arm64: dts: ti: minor whitespace cleanup around '='

The DTS code coding style expects exactly one space before and after '='
sign.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org

arm64: dts: ti: minor whitespace cleanup around '='

The DTS code coding style expects exactly one space before and after '='
sign.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230702185221.44319-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Nishanth Menon <nm@ti.com>

show more ...

arm64: dts: ti: k3-j721e: Add ESM support

Add address entry mapping ESM on J721E.

Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Link: https://lore.kernel.org/r/20230504080526.133149-3-n-fra

arm64: dts: ti: k3-j721e: Add ESM support

Add address entry mapping ESM on J721E.

Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Link: https://lore.kernel.org/r/20230504080526.133149-3-n-francis@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>

show more ...

arm64: dts: ti: k3-j721e: Configure pinctrl for timer IO

There are timer IO pads in the MCU domain, and in the MAIN domain. These
pads can be muxed for the related timers.

There are timer IO contro

arm64: dts: ti: k3-j721e: Configure pinctrl for timer IO

There are timer IO pads in the MCU domain, and in the MAIN domain. These
pads can be muxed for the related timers.

There are timer IO control registers for input and output. The registers
for CTRLMMR_TIMER*_CTRL and CTRLMMR_MCU_TIMER*_CTRL are used to control
the input. The registers for CTCTRLMMR_TIMERIO*_CTRL and
CTRLMMR_MCU_TIMERIO*_CTRL the output.

The multiplexing is documented in Technical Reference Manual[1] under
"Timer IO Muxing Control Registers" and "Timer IO Muxing Control
Registers", and the "Timers Overview" chapters.

We do not expose the cascade_en bit due to the racy usage of
independent 32 bit registers in-line with the timer instantiation in
the device tree. The MCU timer controls are also marked as reserved for
usage by the MCU firmware.

[1] http://www.ti.com/lit/pdf/spruil1

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230531213215.602395-3-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>

show more ...

arm64: dts: ti: k3-j721e: Add general purpose timers

There are 20 general purpose timers on j721e that can be used for
things like PWM using pwm-omap-dmtimer driver. There are also
additional ten ti

arm64: dts: ti: k3-j721e: Add general purpose timers

There are 20 general purpose timers on j721e that can be used for
things like PWM using pwm-omap-dmtimer driver. There are also
additional ten timers in the MCU domain which are meant for MCU
firmware usage and hence marked reserved by default.

The odd numbered timers have the option of being cascaded to even
timers to create a 64 bit non-atomic counter which is racy in simple
usage, hence the clock muxes are explicitly setup to individual 32 bit
counters driven off system crystal (HFOSC) as default.

These instantiation differs from J7200 and other SoCs with the device
IDs and clocks involved for muxing.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230531213215.602395-2-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>

show more ...

arm64: dts: ti: k3-j721e: Enable MDIO nodes at the board level

MDIO nodes defined in the top-level J721e SoC dtsi files are incomplete
and will not be functional unless they are extended with a pinm

arm64: dts: ti: k3-j721e: Enable MDIO nodes at the board level

MDIO nodes defined in the top-level J721e SoC dtsi files are incomplete
and will not be functional unless they are extended with a pinmux.

As the attached PHY is only known about at the board integration level,
these nodes should only be enabled when provided with this information.

Disable the MDIO nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.

Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20230515172137.474626-5-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>

show more ...

arm64: dts: ti: k3-j721e: Enable PCIe nodes at the board level

PCIe nodes defined in the top-level J721e SoC dtsi files are incomplete
and will not be functional unless they are extended with a SerD

arm64: dts: ti: k3-j721e: Enable PCIe nodes at the board level

PCIe nodes defined in the top-level J721e SoC dtsi files are incomplete
and will not be functional unless they are extended with a SerDes PHY.
And usually only one of the two modes can be used at a time as they
share a SerDes link.

As the PHY and mode is only known at the board integration level, these
nodes should only be enabled when provided with this information.

Disable the PCIe nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.

Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20230515172137.474626-3-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>

show more ...

arm64: dts: ti: k3-j721e: Remove PCIe endpoint nodes

These nodes are example nodes for the PCIe controller in "endpoint" mode.
By default the controller is in "root complex" mode and there is alread

arm64: dts: ti: k3-j721e: Remove PCIe endpoint nodes

These nodes are example nodes for the PCIe controller in "endpoint" mode.
By default the controller is in "root complex" mode and there is already a
DT node for the same.

Examples should go in the bindings or other documentation.

Remove this node.

Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20230515172137.474626-2-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>

show more ...

arm64: dts: ti: k3-j721e-main: Update delay select values for MMC subsystems

Update the delay values for various speed modes supported, based on
the revised august 2021 J721E Datasheet.

[1] - Table

arm64: dts: ti: k3-j721e-main: Update delay select values for MMC subsystems

Update the delay values for various speed modes supported, based on
the revised august 2021 J721E Datasheet.

[1] - Table 7-77. MMC0 DLL Delay Mapping for All Timing Modes and
Table 7-86. MMC1/2 DLL Delay Mapping for All Timing Modes, in
https://www.ti.com/lit/ds/symlink/tda4vm.pdf,
(SPRSP36J – FEBRUARY 2019 – REVISED AUGUST 2021)

Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Link: https://lore.kernel.org/r/20230424093827.1378602-1-b-kapoor@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>

show more ...

arm64: dts: ti: k3-j721e: Add MCSPI nodes

J721E has 8 MCSPI instances in the main domain and 3 instances
in the MCU domain. Add the DT nodes for all the 11 instances and
keep them disabled. MAIN_MCS

arm64: dts: ti: k3-j721e: Add MCSPI nodes

J721E has 8 MCSPI instances in the main domain and 3 instances
in the MCU domain. Add the DT nodes for all the 11 instances and
keep them disabled. MAIN_MCSPI4 is connected as a slave to MCU_MCSPI2
by default at power-up, MAIN_MCSPI4 and MCU_MCSPI2 are not pinned out
externally.

Co-developed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Reviewed-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20230321082827.14274-2-vaishnav.a@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>

show more ...

arm64: dts: ti: k3-j721e: Add CPSW9G nodes

TI's J721E SoC has a 9 port Ethernet Switch instance with 8 external
ports and 1 host port, referred to as CPSW9G.

Add device-tree nodes for CPSW9G and di

arm64: dts: ti: k3-j721e: Add CPSW9G nodes

TI's J721E SoC has a 9 port Ethernet Switch instance with 8 external
ports and 1 host port, referred to as CPSW9G.

Add device-tree nodes for CPSW9G and disable it by default. Device-tree
overlays will be used to enable it.

Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20230315062307.1612220-2-s-vadapalli@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>

show more ...

arm64: dts: ti: k3-j721e-main: Remove ti,strobe-sel property

According to latest errata of J721e [1], (i2024) 'MMCSD: Peripherals
Do Not Support HS400' which applies to MMCSD0 subsystem. Speed modes

arm64: dts: ti: k3-j721e-main: Remove ti,strobe-sel property

According to latest errata of J721e [1], (i2024) 'MMCSD: Peripherals
Do Not Support HS400' which applies to MMCSD0 subsystem. Speed modes
supported has been already updated but missed dropping 'ti,strobe-sel'
property which is only required by HS400 speed mode.

Thus, drop 'ti,strobe-sel' property from kernel dtsi for J721e SoC.

[1] https://www.ti.com/lit/er/sprz455/sprz455.pdf

Fixes: eb8f6194e807 ("arm64: dts: ti: k3-j721e-main: Update the speed modes supported and their itap delay values for MMCSD subsystems")
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Diwakar Dhyani <d-dhyani@ti.com>
Reviewed-by: Nitin Yadav <n-yadav@ti.com>
Link: https://lore.kernel.org/r/20230203073724.29529-1-b-kapoor@ti.com

show more ...

arm64: dts: ti: k3-j721e-main: Drop RNG clock

The x1-clk used by trng submodule comes directly from the system clock
after a fixed divider. It is always running and has a fixed frequency
that cannot

arm64: dts: ti: k3-j721e-main: Drop RNG clock

The x1-clk used by trng submodule comes directly from the system clock
after a fixed divider. It is always running and has a fixed frequency
that cannot be changed, making it uncontrollable. Hence this property
should be dropped from the rng node.

Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20221107110607.59216-3-j-choudhary@ti.com

show more ...

arm64: dts: ti: k3-j721e-main: Drop dma-coherent in crypto node

crypto driver itself is not dma-coherent. So drop it.

Fixes: 8ebcaaae8017 ("arm64: dts: ti: k3-j721e-main: Add crypto accelerator nod

arm64: dts: ti: k3-j721e-main: Drop dma-coherent in crypto node

crypto driver itself is not dma-coherent. So drop it.

Fixes: 8ebcaaae8017 ("arm64: dts: ti: k3-j721e-main: Add crypto accelerator node")
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
Link: https://lore.kernel.org/r/20221031152520.355653-3-j-choudhary@ti.com

show more ...

arm64: dts: ti: k3-j721e-main: Add dts nodes for EHRPWMs

Add dts nodes for 6 EHRPWM instances on SoC. Disable EHRPWM nodes in the
dtsi files and only enable the ones that are actually pinned out on

arm64: dts: ti: k3-j721e-main: Add dts nodes for EHRPWMs

Add dts nodes for 6 EHRPWM instances on SoC. Disable EHRPWM nodes in the
dtsi files and only enable the ones that are actually pinned out on a
given board.

Includes a minor formatting fixup for the serdes node to line up the
nodes appropriately.

Signed-off-by: Vijay Pothukuchi <vijayp@ti.com>
Signed-off-by: Rahul T R <r-ravikumar@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20221107070009.11500-2-r-ravikumar@ti.com

show more ...

arm64: dts: ti: k3-j721e: Enable Mailbox nodes at the board level

Mailbox nodes defined in the top-level J721e SoC dtsi files are incomplete
and may not be functional unless they are extended with a

arm64: dts: ti: k3-j721e: Enable Mailbox nodes at the board level

Mailbox nodes defined in the top-level J721e SoC dtsi files are incomplete
and may not be functional unless they are extended with a chosen interrupt
and connection to a remote processor.

As the remote processors depend on memory nodes which are only known at
the board integration level, these nodes should only be enabled when
provided with the above information.

Disable the Mailbox nodes in the dtsi files and only enable the ones that
are actually used on a given board.

Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221020160305.18711-9-afd@ti.com

show more ...

arm64: dts: ti: k3-j721e: Enable MCAN nodes at the board level

MCAN nodes defined in the top-level J721e SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux

arm64: dts: ti: k3-j721e: Enable MCAN nodes at the board level

MCAN nodes defined in the top-level J721e SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux
information.

As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.

Disable the MCAN nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.

Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221020160305.18711-5-afd@ti.com

show more ...

arm64: dts: ti: k3-j721e: Enable MCASP nodes at the board level

MCASP nodes defined in the top-level J721e SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmu

arm64: dts: ti: k3-j721e: Enable MCASP nodes at the board level

MCASP nodes defined in the top-level J721e SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux
information.

As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.

Disable the MCASP nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.

Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221020160305.18711-4-afd@ti.com

show more ...