|
Revision tags: v6.6.25, v6.6.24, v6.6.23, v6.6.16, v6.6.15, v6.6.14, v6.6.13, v6.6.12, v6.6.11, v6.6.10, v6.6.9, v6.6.8, v6.6.7, v6.6.6, v6.6.5, v6.6.4, v6.6.3, v6.6.2, v6.5.11, v6.6.1, v6.5.10, v6.6, v6.5.9, v6.5.8, v6.5.7, v6.5.6, v6.5.5, v6.5.4, v6.5.3, v6.5.2, v6.1.51, v6.5.1, v6.1.50, v6.5, v6.1.49, v6.1.48, v6.1.46, v6.1.45, v6.1.44, v6.1.43, v6.1.42, v6.1.41, v6.1.40 |
|
| #
8d08d7aa |
| 21-Jul-2023 |
Jayesh Choudhary <j-choudhary@ti.com> |
arm64: dts: ti: Use local header for SERDES MUX idle-state values
The DTS uses constants for SERDES MUX idle state values which were earlier
provided as bindings header. But they are unsuitable for
arm64: dts: ti: Use local header for SERDES MUX idle-state values
The DTS uses constants for SERDES MUX idle state values which were earlier
provided as bindings header. But they are unsuitable for bindings.
So move these constants in a header next to DTS.
Also add J784S4 SERDES4 lane definitions which were missed earlier.
Suggested-by: Nishanth Menon <nm@ti.com>
Suggested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Suggested-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/linux-arm-kernel/b24c2124-fe3b-246c-9af9-3ecee9fb32d4@kernel.org/
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Peter Rosin <peda@axentia.se>
Link: https://lore.kernel.org/r/20230721125732.122421-2-j-choudhary@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
show more ...
|
|
Revision tags: v6.1.39, v6.1.38, v6.1.37, v6.1.36, v6.4, v6.1.35 |
|
| #
a4956811 |
| 15-Jun-2023 |
Tony Lindgren <tony@atomide.com> |
arm64: dts: ti: Unify pin group node names for make dtbs checks
Prepare for pinctrl-single yaml binding and unify pin group node names.
Let's standardize on pin group node naming ending in -pins. A
arm64: dts: ti: Unify pin group node names for make dtbs checks
Prepare for pinctrl-single yaml binding and unify pin group node names.
Let's standardize on pin group node naming ending in -pins. As we don't
necessarily have a SoC specific compatible property for pinctrl-single.
I'd rather not add a pattern match for pins somewhere in the name for all
the users.
Trying to add matches for pins-default will be futile as on the earlier
SoCs we've already seen names like pins-sleep, pins-idle, pins-off and so
on that would need to be matched.
And as the node is a pin group, let's prefer to use naming -pins rather
than -pin as more pins may need to be added to the pin group later on.
Signed-off-by: Tony Lindgren <tony@atomide.com>
[vigneshr@ti.com: Rebase onto latest ti/next and extend to new nodes]
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
show more ...
|
|
Revision tags: v6.1.34, v6.1.33, v6.1.32, v6.1.31, v6.1.30, v6.1.29, v6.1.28, v6.1.27, v6.1.26, v6.3, v6.1.25, v6.1.24, v6.1.23, v6.1.22, v6.1.21, v6.1.20 |
|
| #
496cdc82 |
| 15-Mar-2023 |
Siddharth Vadapalli <s-vadapalli@ti.com> |
arm64: dts: ti: k3-j7200: Add overlay to enable CPSW5G ports in QSGMII mode
The J7 Quad Port Add-On Ethernet Card for J7200 Common-Proc-Board supports
QSGMII mode. Use the overlay to configure CPSW5
arm64: dts: ti: k3-j7200: Add overlay to enable CPSW5G ports in QSGMII mode
The J7 Quad Port Add-On Ethernet Card for J7200 Common-Proc-Board supports
QSGMII mode. Use the overlay to configure CPSW5G ports in QSGMII mode.
Add support to reset the PHY from kernel by using gpio-hog and gpio-reset.
Add aliases for CPSW5G ports to enable kernel to fetch MAC addresses
directly from U-Boot.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20230315062307.1612220-5-s-vadapalli@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
show more ...
|