1// SPDX-License-Identifier: GPL-2.0
2/**
3 * DT Overlay for CPSW5G in QSGMII mode using J7 Quad Port ETH EXP Add-On Ethernet Card with
4 * J7200 board.
5 *
6 * Copyright (C) 2023 Texas Instruments Incorporated - https://www.ti.com/
7 */
8
9/dts-v1/;
10/plugin/;
11
12#include <dt-bindings/gpio/gpio.h>
13#include <dt-bindings/mux/ti-serdes.h>
14
15#include "k3-pinctrl.h"
16
17&{/} {
18	aliases {
19		ethernet1 = "/bus@100000/ethernet@c000000/ethernet-ports/port@1";
20		ethernet2 = "/bus@100000/ethernet@c000000/ethernet-ports/port@2";
21		ethernet3 = "/bus@100000/ethernet@c000000/ethernet-ports/port@3";
22		ethernet4 = "/bus@100000/ethernet@c000000/ethernet-ports/port@4";
23	};
24};
25
26&cpsw0 {
27	status = "okay";
28};
29
30&cpsw0_port1 {
31	status = "okay";
32	phy-handle = <&cpsw5g_phy0>;
33	phy-mode = "qsgmii";
34	mac-address = [00 00 00 00 00 00];
35	phys = <&cpsw0_phy_gmii_sel 1>;
36};
37
38&cpsw0_port2 {
39	status = "okay";
40	phy-handle = <&cpsw5g_phy1>;
41	phy-mode = "qsgmii";
42	mac-address = [00 00 00 00 00 00];
43	phys = <&cpsw0_phy_gmii_sel 2>;
44};
45
46&cpsw0_port3 {
47	status = "okay";
48	phy-handle = <&cpsw5g_phy2>;
49	phy-mode = "qsgmii";
50	mac-address = [00 00 00 00 00 00];
51	phys = <&cpsw0_phy_gmii_sel 3>;
52};
53
54&cpsw0_port4 {
55	status = "okay";
56	phy-handle = <&cpsw5g_phy3>;
57	phy-mode = "qsgmii";
58	mac-address = [00 00 00 00 00 00];
59	phys = <&cpsw0_phy_gmii_sel 4>;
60};
61
62&cpsw5g_mdio {
63	status = "okay";
64	pinctrl-names = "default";
65	pinctrl-0 = <&mdio0_pins_default>;
66	reset-gpios = <&exp2 17 GPIO_ACTIVE_LOW>;
67	reset-post-delay-us = <120000>;
68	#address-cells = <1>;
69	#size-cells = <0>;
70
71	cpsw5g_phy0: ethernet-phy@16 {
72		reg = <16>;
73	};
74	cpsw5g_phy1: ethernet-phy@17 {
75		reg = <17>;
76	};
77	cpsw5g_phy2: ethernet-phy@18 {
78		reg = <18>;
79	};
80	cpsw5g_phy3: ethernet-phy@19 {
81		reg = <19>;
82	};
83};
84
85&exp2 {
86	qsgmii-line-hog {
87		gpio-hog;
88		gpios = <16 GPIO_ACTIVE_HIGH>;
89		output-low;
90		line-name = "qsgmii-pwrdn-line";
91	};
92};
93
94&main_pmx0 {
95	mdio0_pins_default: mdio0-pins-default {
96		pinctrl-single,pins = <
97			J721E_IOPAD(0x00a8, PIN_OUTPUT, 5) /* (W19) UART8_TXD.MDIO0_MDC */
98			J721E_IOPAD(0x00a4, PIN_INPUT, 5) /* (W14) UART8_RXD.MDIO0_MDIO */
99		>;
100	};
101};
102