ARM: dts: sunxi: Add Libre Computer ALL-H3-IT H5 board

The Libre Computer ALL-H3-IT board is a small single board computer that
is roughly the same size as the Raspberry Pi Zero, or arou

ARM: dts: sunxi: Add Libre Computer ALL-H3-IT H5 board

The Libre Computer ALL-H3-IT board is a small single board computer that
is roughly the same size as the Raspberry Pi Zero, or around 20% smaller
than a credit card.

The board features:

- H2, H3, or H5 SoC from Allwinner
- 2 DDR3 DRAM chips
- Realtek RTL8821CU based WiFi module
- 128 Mbit SPI-NOR flash
- micro-SD card slot
- micro HDMI video output
- FPC connector for camera sensor module
- generic Raspberri-Pi style 40 pin GPIO header
- additional pin headers for extra USB host ports, ananlog audio and
IR receiver

Only H5 variant test samples were made available, but the vendor does
have plans to include at least an H3 variant. Thus the device tree is
split much like the ALL-H3-CC, with a common dtsi file for the board
design, and separate dts files including the common board file and the
SoC dtsi file. The other variants will be added as they are made
available.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

show more ...

arm64: dts: allwinner: add pineh64 model B

This patch adds the model B of the PineH64.
The model B is smaller than the pine64 model A and has no PCIE slot.

The only devicetree d

arm64: dts: allwinner: add pineh64 model B

This patch adds the model B of the PineH64.
The model B is smaller than the pine64 model A and has no PCIE slot.

The only devicetree difference with the pineH64 model A, is the PHY
regulator and the HDMI connector node.

Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

show more ...

arm64: dts: allwinner: a64: Add A64 OlinuXino board (with eMMC)

A64 OLinuXino board from Olimex has three variants with onboard eMMC:
A64-OLinuXino-1Ge16GW, A64-OLinuXino-1Ge4GW and A64-

arm64: dts: allwinner: a64: Add A64 OlinuXino board (with eMMC)

A64 OLinuXino board from Olimex has three variants with onboard eMMC:
A64-OLinuXino-1Ge16GW, A64-OLinuXino-1Ge4GW and A64-OLinuXino-2Ge8G-IND. In
addition, there are two variants without eMMC. One without eMMC and one with SPI
flash. This suggests the need for separate device tree for the three eMMC
variants.

This patch has been tested on A64-OLinuXino-1Ge16GW with Linux 5.0 from Debain.
Basic benchmarks using Flexible IO Tester show reasonable performance from the
eMMC.

eMMC - Random Write: 21.3MiB/s
eMMC - Sequential Write: 68.2MiB/s
SD Card - Random Write: 1690KiB/s
SD Card - Sequential Write: 11.0MiB/s

Changes:

v3: Separate dts for eMMC variants

v2: Fix descriptions for VCC and VCCQ

Link: https://github.com/armbian/build/commit/174953de1eb09e6aa1ef7075066b573dba625398
Signed-off-by: Martin Ayotte <martinayotte@gmail.com>
[sunil@medhas.org Fix descriptions for VCC and VCCQ, separate dts for eMMC]
Signed-off-by: Sunil Mohan Adapa <sunil@medhas.org>
Tested-by: Sunil Mohan Adapa <sunil@medhas.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

show more ...

arm64: dts: allwinner: h6: Introduce Tanix TX6 board

Tanix TX6 is an Allwinner H6 based TV box, which supports:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 4

arm64: dts: allwinner: h6: Introduce Tanix TX6 board

Tanix TX6 is an Allwinner H6 based TV box, which supports:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 4GiB DDR3 RAM (3GiB useable)
- 100Mbps EMAC via AC200 EPHY
- Cdtech 47822BS Wifi/BT
- 2x USB 2.0 Host and 1x USB 3.0 Host
- HDMI port
- IR receiver
- 64GiB eMMC
- 5V/2A DC power supply

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

show more ...

arm64: dts: allwinner: h6: Add Orange Pi 3 DTS

Orange Pi 3 is a H6 based SBC made by Xulong, released in January 2019. It
has the following features:

- Allwinner H6 quad-core 64

arm64: dts: allwinner: h6: Add Orange Pi 3 DTS

Orange Pi 3 is a H6 based SBC made by Xulong, released in January 2019. It
has the following features:

- Allwinner H6 quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB or 2GB LPDDR3 RAM
- AXP805 PMIC
- AP6256 Wifi/BT 5.0
- USB 2.0 host port (A)
- USB 2.0 micro usb, OTG
- USB 3.0 Host + 4 port USB hub (GL3510)
- Gigabit Ethernet (Realtek RTL8211E phy)
- HDMI 2.0 port
- soldered eMMC (optional)
- 3x LED (one is on the bottom)
- microphone
- audio jack
- PCIe

Add basic support for the board.

Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

show more ...

arm64: dts: allwinner: h6: Introduce Beelink GS1 board

Beelink GS1 is an Allwinner H6 based TV box,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720

arm64: dts: allwinner: h6: Introduce Beelink GS1 board

Beelink GS1 is an Allwinner H6 based TV box,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 2GB LPDDR3 RAM
- AXP805 PMIC
- 1Gbps GMAC via RTL8211E
- FN-Link 6222B-SRB Wifi/BT
- 1x USB 2.0 Host and 1x USB 3.0 Host
- HDMI port
- S/PDIF Tx
- IR receiver
- 5V/2A DC power supply

Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

show more ...

arm64: allwinner: a64: Add Oceanic 5205 5inMFD initial support

Oceanic 5205 5inMFD is a 5 inch Multi function display baseboard
designed to mount SoPine SOM.

Key features:
-

arm64: allwinner: a64: Add Oceanic 5205 5inMFD initial support

Oceanic 5205 5inMFD is a 5 inch Multi function display baseboard
designed to mount SoPine SOM.

Key features:
- Allwinner A64 Cortex-A53
- Mali-400MP2 GPU
- AXP803 PMIC
- 2GB DDR3 RAM
- SD Slot
- SPI-NOR flash
- EMAC, RTL8211E
- MCP2515 CAN
- 4-lane, MIPI-DSI panel
- Goodix 911 CTP
- USB Host
- 12V DC power supply

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

show more ...

Merge tag 'sunxi-h3-h5-for-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt

Allwinner H3/H5 changes for 4.21

Our usual pull request with the changes

Merge tag 'sunxi-h3-h5-for-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt

Allwinner H3/H5 changes for 4.21

Our usual pull request with the changes shared between the H3 and H5 SoCs.

The major changes for this release are:
- Addition of the video engine for the H5
- H3 Camera support
- New board: Emlid Neutis N5, Mapleboard MP130

* tag 'sunxi-h3-h5-for-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: h5: Add Video Engine node
ARM/arm64: dts: allwinner: Move H3/H5 syscon label over to soc-specific nodes
arm64: dts: allwinner: h5: Add system-control node with SRAM C1
ARM: dts: sun8i: h3: Fix the system-control register range
ARM: dts: sun8i: Add the H3/H5 CSI controller
ARM: dts: sun8i-h3: Add dts for the Mapleboard MP130
arm64: dts: allwinner: new board - Emlid Neutis N5
dt-bindings: vendor-prefix: new vendor - Emlid
ARM: dts: sun8i-h3: add sy8106a to orange pi plus

Signed-off-by: Olof Johansson <olof@lixom.net>

show more ...

arm64: allwinner: h6: Add OrangePi Lite2 initial support

OrangePi Lite2 is Allwinner H6 based open-source SBC,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU

arm64: allwinner: h6: Add OrangePi Lite2 initial support

OrangePi Lite2 is Allwinner H6 based open-source SBC,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB LPDDR3 RAM
- AXP805 PMIC
- AP6356S Wifi/BT
- USB 2.0, USB 3.0 Host, OTG
- HDMI port
- 5V/2A DC power supply

Signed-off-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

show more ...

arm64: dts: allwinner: new board - Emlid Neutis N5

Emlid Neutis N5 is a SoM based on Allwinner H5, has a WiFi & BT
module, DDR3 RAM and eMMC.

- add neutis n5 dtsi file for SoM n

arm64: dts: allwinner: new board - Emlid Neutis N5

Emlid Neutis N5 is a SoM based on Allwinner H5, has a WiFi & BT
module, DDR3 RAM and eMMC.

- add neutis n5 dtsi file for SoM needs
- add neutis devboard dts file
- add neutis devboard target to dtb makefile

Signed-off-by: Aleksandr Aleksandrov <aleksandr.aleksandrov@emlid.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

show more ...

Merge tag 'sunxi-dt64-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt

Allwinner arm64 DT changes for 4.20

Our usual set of DT changes for the arm

Merge tag 'sunxi-dt64-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt

Allwinner arm64 DT changes for 4.20

Our usual set of DT changes for the arm64 Allwinner SoCs.

The most notable things are:
- HDMI support on the A64
- New boards: OrangePi One Plus

* tag 'sunxi-dt64-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (28 commits)
arm64: dts: allwinner: a64: a64-olinuxino: set the PHY TX delay
arm64: dts: allwinner: a64: Enable HDMI output on A64 boards w/ HDMI
arm64: dts: allwinner: a64: Add display pipeline
arm64: dts: allwinner: h6: add system controller device tree node
arm64: dts: allwinner: h6: Add OrangePi One Plus initial support
arm64: dts: allwinner: a64: Rename r_i2c_pins_a label to r_i2c_pl89_pins
arm64: dts: allwinner: a64: Rename uart0_pins_a label to uart0_pb_pins
arm64: dts: allwinner: a64: Split out data strobe pin from mmc2 pinmux
arm64: dts: allwinner: a64: NanoPi-A64: Add blue status LED
arm64: dts: allwinner: a64: NanoPi-A64: Add Wifi chip
arm64: dts: allwinner: a64: NanoPi-A64: Add Ethernet
arm64: dts: allwinner: a64: NanoPi-A64: Fix DCDC1 voltage
arm64: dts: allwinner: a64: Olinuxino: enable USB
arm64: dts: allwinner: a64: Olinuxino: add Ethernet nodes
arm64: dts: allwinner: a64: Olinuxino: fix DRAM voltage
arm64: dts: allwinner: a64: Orange Pi Win: Adjust CSI power rails
arm64: dts: allwinner: a64: Orange Pi Win: Add SPI flash node
arm64: dts: allwinner: a64: Orange Pi Win: Add SDIO node
arm64: dts: allwinner: a64: Orange Pi Win: Add LED node
arm64: dts: allwinner: a64: Orange Pi Win: Add UARTs
...

Signed-off-by: Arnd Bergmann <arnd@arndb.de>

show more ...

ARM: dts: sunxi: h3-h5: Add Bananapi M2+ v1.2 device trees

Bananapi released an updated revision of the H3/H5 based Bananapi M2+.
Version 1.2 enables voltage control for the CPU's regula

ARM: dts: sunxi: h3-h5: Add Bananapi M2+ v1.2 device trees

Bananapi released an updated revision of the H3/H5 based Bananapi M2+.
Version 1.2 enables voltage control for the CPU's regulator by using
a GPIO line to toggle a MOSFET that can change the effective resistance
value in the regulator's feedback network.

This patch adds a common .dtsi file for this new revision, which
includes the original common sunxi-bananapi-m2-plus.dtsi file, and
adds the GPIO-controlled regulator and a cpu-supply reference. H3
and H5 variant dts files are added as well.

Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

show more ...

arm64: dts: allwinner: h5: Add device tree for Bananapi M2 Plus H5

The Bananapi M2 Plus H5 is a variant of the original Bananapi M2 Plus,
with the H3 SoC replaced with an H5. Everything

arm64: dts: allwinner: h5: Add device tree for Bananapi M2 Plus H5

The Bananapi M2 Plus H5 is a variant of the original Bananapi M2 Plus,
with the H3 SoC replaced with an H5. Everything else is the same.

Add a stub device tree incorporating the shared bananapi-m2-plus dtsi
file.

Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

show more ...

arm64: dts: allwinner: h6: Add OrangePi One Plus initial support

OrangePi One Plus is Allwinner H6 based open-source SBC,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A5

arm64: dts: allwinner: h6: Add OrangePi One Plus initial support

OrangePi One Plus is Allwinner H6 based open-source SBC,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB LPDDR3 RAM
- AXP805 PMIC
- 1Gbps GMAC via RTL8211
- USB 2.0 Host, OTG
- HDMI port
- 5V/2A DC power supply

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

show more ...

arm64: dts: allwinner: a64: Add Pine64-LTS device tree file

The Pine64-LTS is a variant of the Pine64 board, from the software
visible side resembling a SoPine module on a baseboard, tho

arm64: dts: allwinner: a64: Add Pine64-LTS device tree file

The Pine64-LTS is a variant of the Pine64 board, from the software
visible side resembling a SoPine module on a baseboard, though the
board has the SoC and DRAM integrated on one PCB.
Due to this it basically shares the DT with the SoPine baseboard, which
we mimic in our DT by inclucing the boardboard .dts into the new file,
just overwriting the model name.
Having a separate .dts for this seems useful, since we don't know yet if
there are subtle differences between the two. Also the SoC on the LTS
board is technically an "R18" instead of the original "A64", although as
far as we know this is just a relabelled version of the original SoC.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

show more ...

arm64: dts: allwinner: add support for Pinebook

Pinebook is a A64-based laptop produced by Pine64, with the following
peripherals:

USB:
- Two external USB ports (one is dire

arm64: dts: allwinner: add support for Pinebook

Pinebook is a A64-based laptop produced by Pine64, with the following
peripherals:

USB:
- Two external USB ports (one is directly connected to A64's OTG
controller, the other is under a internal hub connected to the host-only
controller.)
- USB HID keyboard and touchpad connected to the internal hub.
- USB UVC camera connected to the internal hub.

Power-related:
- A DC IN jack connected to AXP803's DCIN pin.
- A Li-Polymer battery connected to AXP803's battery pins.

Storage:
- An eMMC by Foresee on the main board (in the product revision of the
main board it's designed to be switchable).
- An external MicroSD card slot.

Display:
- An eDP LCD panel (1366x768) connected via an ANX6345 RGB-eDP bridge.
- A mini HDMI port.

Misc:
- A Hall sensor designed to detect the status of lid, connected to GPIO PL12.
- A headphone jack connected to the SoC's internal codec.
- A debug UART port muxed with headphone jack.

This commit adds basical support for it.

[vasily: squashed several commits into one, added simplefb node, added usbphy
to ehci0 and ohci0 nodes and other cosmetic changes to dts]

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

show more ...

arm64: allwinner: a64: Add Amarula A64-Relic initial support

Amarula A64-Relic is Allwinner A64 based IoT device, which support
- Allwinner A64 Cortex-A53
- Mali-400MP2 GPU
- AXP

arm64: allwinner: a64: Add Amarula A64-Relic initial support

Amarula A64-Relic is Allwinner A64 based IoT device, which support
- Allwinner A64 Cortex-A53
- Mali-400MP2 GPU
- AXP803 PMIC
- 1GB DDR3 RAM
- 8GB eMMC
- AP6330 Wifi/BLE
- MIPI-DSI
- CSI: OV5640 sensor
- USB OTG
- 12V DC power supply

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

show more ...

arm64: dts: allwinner: Add dts file for Libre Computer Board ALL-H3-CC H5 ver.

The Libre Computer Board ALL-H3-CC from Libre Technology is a Raspberry
Pi B+ form factor single board comp

arm64: dts: allwinner: Add dts file for Libre Computer Board ALL-H3-CC H5 ver.

The Libre Computer Board ALL-H3-CC from Libre Technology is a Raspberry
Pi B+ form factor single board computer based on the Allwinner H2+, H3,
or H5 SoCs with the same PCB.
The board has 2GB DDR3 SDRAM, provided by 4 2Gb chips. The mounting holes
and connectors are in the exact same position as on the Raspberry Pi B+.

This patch enables the H5 variant using the H3 board definition moved to
a common dtsi in an earlier patch. The dts simply include the common dtsi
and declares the correct compatible and model of the H5 variant.

Suggested-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

show more ...

arm64: dts: allwinner: Sort dtb entries in Makefile

The dtb entries for NanoPi boards in the device tree makefile somehow
ended up after the Orange Pi boards.

Move them so the l

arm64: dts: allwinner: Sort dtb entries in Makefile

The dtb entries for NanoPi boards in the device tree makefile somehow
ended up after the Orange Pi boards.

Move them so the list is properly sorted.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

show more ...

Merge tag 'sunxi-h3-h5-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt

Pull "Allwinner H3/H5 changes for 4.17" from Maxime Ripard:

Here is o

Merge tag 'sunxi-h3-h5-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt

Pull "Allwinner H3/H5 changes for 4.17" from Maxime Ripard:

Here is our usual bunch of changes to the common DTSI shared between arm
and arm64, and their associated device trees.

Even though the diffstat is quite big, it's been mostly just cleanups. The
big feature is that the HDMI is now suported on H3 and H5 boards.

* tag 'sunxi-h3-h5-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: allwinner: H5: Add Xunlong Orange Pi Zero Plus
ARM: dts: sun8i-h3: Add Mali node
ARM64: dts: sun50i: h5: Enable HDMI output on H5 boards
ARM: dts: sun8i: h3: Enable HDMI output on H3 boards
ARM: dts: sunxi: h3/h5: Add HDMI pipeline
ARM: dts: sun8i: h2-plus: remove unnecessary mmc1_pins node
ARM: dts: sunxi: h3-h5: rename mmc0_pins_a and mmc1_pins_a
ARM: dts: sunxi: h3-h5: Move pinctrl of mmc1 from dts to dtsi
ARM: dts: sunxi: h3-h5: Move pinctrl of mmc0 from dts to dtsi
ARM: dts: sunxi: h3-h5: remove mmc0 card detection pin from pinctrl
ARM: dts: sun8i: h2+: add support for Banana Pi M2 Zero board
ARM: dts: sunxi: Switch MMC nodes away from cd-inverted property
ARM: dts: nanopi-neo-air: Add WiFi / eMMC

show more ...

arm64: allwinner: H5: Add Xunlong Orange Pi Zero Plus

The Xunlong Orange Pi Zero Plus is single board computer.
- H5 Quad-core 64-bit Cortex-A53
- 512MB DDR3
- microSD slot
-

arm64: allwinner: H5: Add Xunlong Orange Pi Zero Plus

The Xunlong Orange Pi Zero Plus is single board computer.
- H5 Quad-core 64-bit Cortex-A53
- 512MB DDR3
- microSD slot
- Debug TTL UART
- 1000M/100M/10M Ethernet RJ45
- Realtek RTL8189FTV
- Spi flash (2MB)
- One USB 2.0 HOST, One USB 2.0 OTG

This is based on a patch from armbian:
https://github.com/armbian/build/blob/master/patch/kernel/sunxi-next/sunxi-add-orangepi-zero-plus.patch

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

show more ...

arm64: dts: allwinner: a64: Add support for TERES-I laptop

The TERES-I is an open hardware laptop built by Olimex using the
Allwinner A64 SoC.

Add the board specific .dts file,

arm64: dts: allwinner: a64: Add support for TERES-I laptop

The TERES-I is an open hardware laptop built by Olimex using the
Allwinner A64 SoC.

Add the board specific .dts file, which includes the A64 .dtsi and
enables the peripherals that we support so far.

Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

show more ...

arm64: allwinner: h6: add support for Pine H64 board

Pine H64 is an Allwinner H6-based SBC from Pine64, with the following
features:

- 1GiB/2GiB/4GiB LPDDR3 DRAM (in 4GiB situat

arm64: allwinner: h6: add support for Pine H64 board

Pine H64 is an Allwinner H6-based SBC from Pine64, with the following
features:

- 1GiB/2GiB/4GiB LPDDR3 DRAM (in 4GiB situation only 3GiB is
accessible)
- AXP805 PMIC
- Raspberry-Pi-compatible GPIO header, "Euler" GPIO header (not
compatible with the "Euler" on Pine A64) and "Expansion" pin header
- 2 USB 2.0 ports and 1 USB 3.0 ports
- Audio jack
- MicroSD slot and eMMC module slot
- on-board SPI NOR flash
- 1Gbps Ethernet port (via RTL8211E PHY)
- HDMI port

Adds initial support for it, including the UART on the Expansion pin
header.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

show more ...

Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM device-tree updates from Arnd Bergmann:
"We add device tree files for a couple of additional

Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM device-tree updates from Arnd Bergmann:
"We add device tree files for a couple of additional SoCs in various
areas:

Allwinner R40/V40 for entertainment, Broadcom Hurricane 2 for
networking, Amlogic A113D for audio, and Renesas R-Car V3M for
automotive.

As usual, lots of new boards get added based on those and other SoCs:

- Actions S500 based CubieBoard6 single-board computer

- Amlogic Meson-AXG A113D based development board
- Amlogic S912 based Khadas VIM2 single-board computer
- Amlogic S912 based Tronsmart Vega S96 set-top-box

- Allwinner H5 based NanoPi NEO Plus2 single-board computer
- Allwinner R40 based Banana Pi M2 Ultra and Berry single-board computers
- Allwinner A83T based TBS A711 Tablet

- Broadcom Hurricane 2 based Ubiquiti UniFi Switch 8
- Broadcom bcm47xx based Luxul XAP-1440/XAP-810/ABR-4500/XBR-4500
wireless access points and routers

- NXP i.MX51 based Zodiac Inflight Innovations RDU1 board
- NXP i.MX53 based GE Healthcare PPD biometric monitor
- NXP i.MX6 based Pistachio single-board computer
- NXP i.MX6 based Vining-2000 automotive diagnostic interface
- NXP i.MX6 based Ka-Ro TX6 Computer-on-Module in additional variants

- Qualcomm MSM8974 (Snapdragon 800) based Fairphone 2 phone
- Qualcomm MSM8974pro (Snapdragon 801) based Sony Xperia Z2 Tablet

- Realtek RTD1295 based set-top-boxes MeLE V9 and PROBOX2 AVA

- Renesas R-Car V3M (R8A77970) SoC and "Eagle" reference board
- Renesas H3ULCB and M3ULCB "Kingfisher" extension infotainment boards
- Renasas r8a7745 based iWave G22D-SODIMM SoM

- Rockchip rk3288 based Amarula Vyasa single-board computer

- Samsung Exynos5800 based Odroid HC1 single-board computer

For existing SoC support, there was a lot of ongoing work, as usual
most of that concentrated on the Renesas, Rockchip, OMAP, i.MX,
Amlogic and Allwinner platforms, but others were also active.

Rob Herring and many others worked on reducing the number of issues
that the latest version of 'dtc' now warns about. Unfortunately there
is still a lot left to do.

A rework of the ARM foundation model introduced several new files for
common variations of the model"

* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (599 commits)
arm64: dts: uniphier: route on-board device IRQ to GPIO controller for PXs3
dt-bindings: bus: Add documentation for the Technologic Systems NBUS
arm64: dts: actions: s900-bubblegum-96: Add fake uart5 clock
ARM: dts: owl-s500: Add CubieBoard6
dt-bindings: arm: actions: Add CubieBoard6
ARM: dts: owl-s500-guitar-bb-rev-b: Add fake uart3 clock
ARM: dts: owl-s500: Set power domains for CPU2 and CPU3
arm: dts: mt7623: remove unused compatible string for pio node
arm: dts: mt7623: update usb related nodes
arm: dts: mt7623: update crypto node
ARM: dts: sun8i: a711: Enable USB OTG
ARM: dts: sun8i: a711: Add regulator support
ARM: dts: sun8i: a83t: bananapi-m3: Enable AP6212 WiFi on mmc1
ARM: dts: sun8i: a83t: cubietruck-plus: Enable AP6330 WiFi on mmc1
ARM: dts: sun8i: a83t: Move mmc1 pinctrl setting to dtsi file
ARM: dts: sun8i: a83t: allwinner-h8homlet-v2: Add AXP818 regulator nodes
ARM: dts: sun8i: a83t: bananapi-m3: Add AXP813 regulator nodes
ARM: dts: sun8i: a83t: cubietruck-plus: Add AXP818 regulator nodes
ARM: dts: sunxi: Add dtsi for AXP81x PMIC
arm64: dts: allwinner: H5: Restore EMAC changes
...

show more ...

Merge tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux

Pull DeviceTree updates from Rob Herring:
"A bigger diffstat than usual with the kbuild chang

Merge tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux

Pull DeviceTree updates from Rob Herring:
"A bigger diffstat than usual with the kbuild changes and a tree wide
fix in the binding documentation.

Summary:

- kbuild cleanups and improvements for dtbs

- Code clean-up of overlay code and fixing for some long standing
memory leak and race condition in applying overlays

- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.

- Final piece of removing storing the full path for every DT node.
The prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.

- Sync with current upstream dtc. This brings additional checks to
dtb compiling.

- Binding doc tree wide removal of leading 0s from examples

- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings

- Vendor prefix documentation for nutsboard, Silicon Storage
Technology, shimafuji, Tecon Microprocessor Technologies, DH
electronics GmbH, Opal Kelly, and Next Thing"

* tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (55 commits)
dt-bindings: usb: add #phy-cells to usb-nop-xceiv
dt-bindings: Remove leading zeros from bindings notation
kbuild: handle dtb-y and CONFIG_OF_ALL_DTBS natively in Makefile.lib
MIPS: dts: remove bogus bcm96358nb4ser.dtb from dtb-y entry
kbuild: clean up *.dtb and *.dtb.S patterns from top-level Makefile
.gitignore: move *.dtb and *.dtb.S patterns to the top-level .gitignore
.gitignore: sort normal pattern rules alphabetically
dt-bindings: add vendor prefix for Next Thing Co.
scripts/dtc: Update to upstream version v1.4.5-6-gc1e55a5513e9
of: dynamic: fix memory leak related to properties of __of_node_dup
of: overlay: make pr_err() string unique
of: overlay: pr_err from return NOTIFY_OK to overlay apply/remove
of: overlay: remove unneeded check for NULL kbasename()
of: overlay: remove a dependency on device node full_name
of: overlay: simplify applying symbols from an overlay
of: overlay: avoid race condition between applying multiple overlays
of: overlay: loosen overly strict phandle clash check
of: overlay: expand check of whether overlay changeset can be removed
of: overlay: detect cases where device tree may become corrupt
of: overlay: minor restructuring
...

show more ...