arm64: dts: allwinner: h616: Add OrangePi Zero 3 board support

The OrangePi Zero 3 is a development board based on the Allwinner H618 SoC,
which seems to be just an H616 with more L2 cache. The boar

arm64: dts: allwinner: h616: Add OrangePi Zero 3 board support

The OrangePi Zero 3 is a development board based on the Allwinner H618 SoC,
which seems to be just an H616 with more L2 cache. The board itself is a
slightly updated version of the Orange Pi Zero 2. It features:
- Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU
- 1/1.5/2/4 GiB LPDDR4 DRAM SKUs (only up to 1GB on the Zero2)
- AXP313a PMIC (more capable AXP305 on the Zero2)
- Raspberry-Pi-1 compatible GPIO header
- extra 13 pin expansion header, exposing pins for 2x USB 2.0 ports
- 1 USB 2.0 host port
- 1 USB 2.0 type C port (power supply + OTG)
- MicroSD slot
- on-board 16MiB bootable SPI NOR flash (only 2MB on the Zero2)
- 1Gbps Ethernet port (via Motorcomm YT8531 PHY) (RTL8211 on the Zero2)
- micro-HDMI port
- (yet) unsupported Allwinner WiFi/BT chip

Add the devicetree file describing the currently supported features,
namely LEDs, SD card, PMIC, SPI flash, USB. Ethernet seems unstable at
the moment, though the basic functionality works.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20230804170856.1237202-4-andre.przywara@arm.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>

show more ...

arm64: dts: allwinner: h616: Add X96 Mate TV box support

The X96 Mate is an Allwinner H616 based TV box, featuring:
- Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU
- 2GiB/4GiB RAM (fully usable!)

arm64: dts: allwinner: h616: Add X96 Mate TV box support

The X96 Mate is an Allwinner H616 based TV box, featuring:
- Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU
- 2GiB/4GiB RAM (fully usable!)
- 16/32/64GiB eMMC
- 100Mbps Ethernet (via embedded AC200 EPHY, not yet supported)
- Unsupported Allwinner WiFi chip
- 2 x USB 2.0 host ports
- HDMI port
- IR receiver
- 5V/2A DC power supply via barrel plug

Add a basic devicetree for it, with SD card and eMMC working, as
well as serial and the essential peripherals, like the AXP PMIC.

This DT is somewhat minimal, and should work on many other similar TV
boxes with the Allwinner H616 chip.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220708105235.3983266-8-andre.przywara@arm.com

show more ...

arm64: dts: allwinner: h616: Add OrangePi Zero 2 board support

The OrangePi Zero 2 is a development board with the new H616 SoC. It
comes with the following features:
- Four ARM Cortex-A53 cores,

arm64: dts: allwinner: h616: Add OrangePi Zero 2 board support

The OrangePi Zero 2 is a development board with the new H616 SoC. It
comes with the following features:
- Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU
- 512MiB/1GiB DDR3 DRAM
- AXP305 PMIC
- Raspberry-Pi-1 compatible GPIO header
- extra 13 pin expansion header, exposing pins for 2x USB 2.0 ports
- 1 USB 2.0 host port
- 1 USB 2.0 type C port (power supply + OTG)
- MicroSD slot
- on-board 2MiB bootable SPI NOR flash
- 1Gbps Ethernet port (via RTL8211F PHY)
- micro-HDMI port
- (yet) unsupported Allwinner WiFi/BT chip

Add the devicetree file describing the currently supported features.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220708105235.3983266-7-andre.przywara@arm.com

show more ...

arm64: dts: allwinner: h6: Add Tanix TX6 mini dts

Tanix TX6 mini is less capable version of Tanix TX6 although it comes
with some features not present on Tanix TX6.

Basic specs:
- H6 SoC
- 2 GiB DD

arm64: dts: allwinner: h6: Add Tanix TX6 mini dts

Tanix TX6 mini is less capable version of Tanix TX6 although it comes
with some features not present on Tanix TX6.

Basic specs:
- H6 SoC
- 2 GiB DDR3 RAM
- HDMI
- SPDIF
- 2x USB
- analogue audio
- CVBS
- SD card
- IR remote
- LED display
- fast ethernet
- XR819 wifi
- 16 GiB eMMC

Currently supported features doesn't differ that much from Tanix TX6,
but that will change soon.

Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

show more ...

arm64: dts: allwinner: h5: Add NanoPi R1S H5 support

The NanoPi R1S H5 is a open source board made by FriendlyElec.
It has the following features:

- Allwinner H5, Quad-core Cortex-A53
- 512MB DDR3

arm64: dts: allwinner: h5: Add NanoPi R1S H5 support

The NanoPi R1S H5 is a open source board made by FriendlyElec.
It has the following features:

- Allwinner H5, Quad-core Cortex-A53
- 512MB DDR3 RAM
- 10/100/1000M Ethernet x 2
- RTL8189ETV WiFi 802.11b/g/n
- USB 2.0 host port (A)
- MicroSD Slot
- Serial Debug Port
- 5V 2A DC power-supply

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210516163523.9484-2-amadeus@jmu.edu.cn

show more ...

arm64: allwinner: dts: a64: add DT for Early Adopter's PineTab

PineTabs since Early Adopter batch will use a new LCD panel.

Add device tree for PineTab with the new panel.

Signed-off-by: Icenowy Z

arm64: allwinner: dts: a64: add DT for Early Adopter's PineTab

PineTabs since Early Adopter batch will use a new LCD panel.

Add device tree for PineTab with the new panel.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201224024001.19248-2-icenowy@aosc.io

show more ...

arm64: allwinner: A100: add support for Allwinner Perf1 board

A100 perf1 is an Allwinner A100-based SBC, with the following features:

- 1GiB DDR3 DRAM
- AXP803 PMIC
- 2 USB 2.0 ports
- MicroSD slot

arm64: allwinner: A100: add support for Allwinner Perf1 board

A100 perf1 is an Allwinner A100-based SBC, with the following features:

- 1GiB DDR3 DRAM
- AXP803 PMIC
- 2 USB 2.0 ports
- MicroSD slot and on-board eMMC module
- on-board Nand flash
- ···

Adds initial support for it, including UART and PMU.

Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/30f4a3fc6ac84d05094e2c3b89d1dddc8ff6b7fc.1595572867.git.frank@allwinnertech.com

show more ...

arm64: dts: allwinner: Add support for PinePhone revision 1.2

Revision 1.2 should be the final production version of the PinePhone.
It has most of the known HW quirks fixed.

Interrupt to the magnet

arm64: dts: allwinner: Add support for PinePhone revision 1.2

Revision 1.2 should be the final production version of the PinePhone.
It has most of the known HW quirks fixed.

Interrupt to the magnetometer is routed correctly, in this revision.

The bulk of the changes are in how modem and the USB-C HDMI bridge
chip is powered and where the signals from the modem are connected.

Also backlight intensity seemingly behaves differently, than on the
1.1 and 1.0 boards, and the PWM duty cycle where backlight starts
to work is 10% (as tested on 2 1.2 PinePhones I have access to).

Signed-off-by: Ondrej Jirman <megous@megous.com>
Link: https://lore.kernel.org/r/20200703194842.111845-3-megous@megous.com
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

show more ...

arm64: dts: allwinner: Add initial support for Pine64 PinePhone

At the moment PinePhone comes in two slightly incompatible variants:

- 1.0: Early Developer Batch
- 1.1: Braveheart Batch

There will

arm64: dts: allwinner: Add initial support for Pine64 PinePhone

At the moment PinePhone comes in two slightly incompatible variants:

- 1.0: Early Developer Batch
- 1.1: Braveheart Batch

There will be at least one more incompatible variant in the very near
future, so let's start by sharing the dtsi among multiple variants,
right away, even though the HW description doesn't yet include the
different bits.

The differences between 1.0 and 1.1 are: change in pins that control
the flash LED, differences in modem power status signal routing, and
maybe some other subtler things, that have not been determined yet.

This is a basic DT that includes only features that are already
supported by mainline drivers.

Co-developed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Co-developed-by: Martijn Braam <martijn@brixit.nl>
Signed-off-by: Martijn Braam <martijn@brixit.nl>
Co-developed-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bhushan Shah <bshah@kde.org>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

show more ...

arm64: dts: allwinner: a64: add support for PineTab

PineTab is a 10.1" tablet by Pine64 with Allwinner A64 inside.

It includes the following peripherals:

USB:
- A microUSB Type-B port connected to

arm64: dts: allwinner: a64: add support for PineTab

PineTab is a 10.1" tablet by Pine64 with Allwinner A64 inside.

It includes the following peripherals:

USB:
- A microUSB Type-B port connected to the OTG-capable USB PHY of
Allwinner A64. The ID pin is connected to a GPIO of the A64 SoC, and the
Vbus is connected to the Vbus of AXP803 PMIC. These enables OTG
functionality on this port.
- A USB Type-A port is connected to the internal hub attached to the
non-OTG USB PHY of Allwinner A64.
- There are reserved pins for an external keyboard connected to the
internal hub.

Power:
- The microUSB port has its Vbus connected to AXP803, mentioned above.
- A DC jack (of a strange size, 2.5mm outer diameter) is connected to
the ACIN of AXP803.
- A Li-Polymer battery is connected to the battery pins of AXP803.

Storage:
- An tradition Pine64 eMMC slot is on the board, mounted with an eMMC
module by factory.
- An external microSD slot is hidden under a protect case.

Display:
- A MIPI-DSI LCD panel (800x1280) is connected to the DSI port of A64 SoC.
- A mini HDMI port.

Input:
- A touch panel attached to a Goodix GT9271 touch controller.
- Volume keys connected to the LRADC of the A64 SoC.

Camera:
- An OV5640 CMOS camera is at rear, connected to the CSI bus of A64 SoC.
- A GC2145 CMOS camera is at front, shares the same CSI bus with OV5640.

Audio:
- A headphone jack is conencted to the SoC's internal codec.
- A speaker connected is to the Line Out port of SoC's internal codec, via
an amplifier.

Misc:
- Debug UART is muxed with the headphone jack, with the switch next to
the microSD slot.
- A bosch BMA223 accelerometer is connected to the I2C bus of A64 SoC.
- Wi-Fi and Bluetooth are available via a RTL8723CS chip, similar to the
one in Pinebook.

This commit adds a basically usable device tree for it, implementing
most of the features mentioned above. HDMI is not supported now because
bad LCD-HDMI coexistence situation of mainline A64 display driver, the
front camera currently lacks a driver and a facility to share the bus
with the rear one, and the accelerometer currently lacks a DT binding.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

show more ...

arm64: dts: allwinner: h5: Add Libre Computer ALL-H5-CC H5 board

The Libre Computer ALL-H5-CC board is an upgraded version of the
ALL-H3-CC. Changes include:

- Gigabit Ethernet via external RTL82

arm64: dts: allwinner: h5: Add Libre Computer ALL-H5-CC H5 board

The Libre Computer ALL-H5-CC board is an upgraded version of the
ALL-H3-CC. Changes include:

- Gigabit Ethernet via external RTL8211E Ethernet PHY
- 16 MiB SPI NOR flash memory
- PoE tap header
- Line out jack removed

Only H5 variant test samples were made available, and the vendor is not
certain whether other SoC variants would be made or not. Furthermore the
board is a minor upgrade compared to the ALL-H3-CC. Thus the device tree
simply includes the one for the ALL-H3-CC, and adds the changes on top.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

show more ...

ARM: dts: sunxi: Add Libre Computer ALL-H3-IT H5 board

The Libre Computer ALL-H3-IT board is a small single board computer that
is roughly the same size as the Raspberry Pi Zero, or around 20% small

ARM: dts: sunxi: Add Libre Computer ALL-H3-IT H5 board

The Libre Computer ALL-H3-IT board is a small single board computer that
is roughly the same size as the Raspberry Pi Zero, or around 20% smaller
than a credit card.

The board features:

- H2, H3, or H5 SoC from Allwinner
- 2 DDR3 DRAM chips
- Realtek RTL8821CU based WiFi module
- 128 Mbit SPI-NOR flash
- micro-SD card slot
- micro HDMI video output
- FPC connector for camera sensor module
- generic Raspberri-Pi style 40 pin GPIO header
- additional pin headers for extra USB host ports, ananlog audio and
IR receiver

Only H5 variant test samples were made available, but the vendor does
have plans to include at least an H3 variant. Thus the device tree is
split much like the ALL-H3-CC, with a common dtsi file for the board
design, and separate dts files including the common board file and the
SoC dtsi file. The other variants will be added as they are made
available.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

show more ...

arm64: dts: allwinner: add pineh64 model B

This patch adds the model B of the PineH64.
The model B is smaller than the pine64 model A and has no PCIE slot.

The only devicetree difference with the p

arm64: dts: allwinner: add pineh64 model B

This patch adds the model B of the PineH64.
The model B is smaller than the pine64 model A and has no PCIE slot.

The only devicetree difference with the pineH64 model A, is the PHY
regulator and the HDMI connector node.

Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

show more ...

arm64: dts: allwinner: a64: Add A64 OlinuXino board (with eMMC)

A64 OLinuXino board from Olimex has three variants with onboard eMMC:
A64-OLinuXino-1Ge16GW, A64-OLinuXino-1Ge4GW and A64-OLinuXino-2G

arm64: dts: allwinner: a64: Add A64 OlinuXino board (with eMMC)

A64 OLinuXino board from Olimex has three variants with onboard eMMC:
A64-OLinuXino-1Ge16GW, A64-OLinuXino-1Ge4GW and A64-OLinuXino-2Ge8G-IND. In
addition, there are two variants without eMMC. One without eMMC and one with SPI
flash. This suggests the need for separate device tree for the three eMMC
variants.

This patch has been tested on A64-OLinuXino-1Ge16GW with Linux 5.0 from Debain.
Basic benchmarks using Flexible IO Tester show reasonable performance from the
eMMC.

eMMC - Random Write: 21.3MiB/s
eMMC - Sequential Write: 68.2MiB/s
SD Card - Random Write: 1690KiB/s
SD Card - Sequential Write: 11.0MiB/s

Changes:

v3: Separate dts for eMMC variants

v2: Fix descriptions for VCC and VCCQ

Link: https://github.com/armbian/build/commit/174953de1eb09e6aa1ef7075066b573dba625398
Signed-off-by: Martin Ayotte <martinayotte@gmail.com>
[sunil@medhas.org Fix descriptions for VCC and VCCQ, separate dts for eMMC]
Signed-off-by: Sunil Mohan Adapa <sunil@medhas.org>
Tested-by: Sunil Mohan Adapa <sunil@medhas.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

show more ...

arm64: dts: allwinner: h6: Introduce Tanix TX6 board

Tanix TX6 is an Allwinner H6 based TV box, which supports:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 4GiB DDR3 RAM (3GiB u

arm64: dts: allwinner: h6: Introduce Tanix TX6 board

Tanix TX6 is an Allwinner H6 based TV box, which supports:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 4GiB DDR3 RAM (3GiB useable)
- 100Mbps EMAC via AC200 EPHY
- Cdtech 47822BS Wifi/BT
- 2x USB 2.0 Host and 1x USB 3.0 Host
- HDMI port
- IR receiver
- 64GiB eMMC
- 5V/2A DC power supply

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

show more ...

arm64: dts: allwinner: h6: Add Orange Pi 3 DTS

Orange Pi 3 is a H6 based SBC made by Xulong, released in January 2019. It
has the following features:

- Allwinner H6 quad-core 64-bit ARM Cortex-A53

arm64: dts: allwinner: h6: Add Orange Pi 3 DTS

Orange Pi 3 is a H6 based SBC made by Xulong, released in January 2019. It
has the following features:

- Allwinner H6 quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB or 2GB LPDDR3 RAM
- AXP805 PMIC
- AP6256 Wifi/BT 5.0
- USB 2.0 host port (A)
- USB 2.0 micro usb, OTG
- USB 3.0 Host + 4 port USB hub (GL3510)
- Gigabit Ethernet (Realtek RTL8211E phy)
- HDMI 2.0 port
- soldered eMMC (optional)
- 3x LED (one is on the bottom)
- microphone
- audio jack
- PCIe

Add basic support for the board.

Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

show more ...

arm64: dts: allwinner: h6: Introduce Beelink GS1 board

Beelink GS1 is an Allwinner H6 based TV box,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 2GB LPDDR3 RAM
- A

arm64: dts: allwinner: h6: Introduce Beelink GS1 board

Beelink GS1 is an Allwinner H6 based TV box,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 2GB LPDDR3 RAM
- AXP805 PMIC
- 1Gbps GMAC via RTL8211E
- FN-Link 6222B-SRB Wifi/BT
- 1x USB 2.0 Host and 1x USB 3.0 Host
- HDMI port
- S/PDIF Tx
- IR receiver
- 5V/2A DC power supply

Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

show more ...

arm64: allwinner: a64: Add Oceanic 5205 5inMFD initial support

Oceanic 5205 5inMFD is a 5 inch Multi function display baseboard
designed to mount SoPine SOM.

Key features:
- Allwinner A64 Cortex-A5

arm64: allwinner: a64: Add Oceanic 5205 5inMFD initial support

Oceanic 5205 5inMFD is a 5 inch Multi function display baseboard
designed to mount SoPine SOM.

Key features:
- Allwinner A64 Cortex-A53
- Mali-400MP2 GPU
- AXP803 PMIC
- 2GB DDR3 RAM
- SD Slot
- SPI-NOR flash
- EMAC, RTL8211E
- MCP2515 CAN
- 4-lane, MIPI-DSI panel
- Goodix 911 CTP
- USB Host
- 12V DC power supply

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

show more ...

arm64: allwinner: h6: Add OrangePi Lite2 initial support

OrangePi Lite2 is Allwinner H6 based open-source SBC,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB LPD

arm64: allwinner: h6: Add OrangePi Lite2 initial support

OrangePi Lite2 is Allwinner H6 based open-source SBC,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB LPDDR3 RAM
- AXP805 PMIC
- AP6356S Wifi/BT
- USB 2.0, USB 3.0 Host, OTG
- HDMI port
- 5V/2A DC power supply

Signed-off-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

show more ...

arm64: dts: allwinner: new board - Emlid Neutis N5

Emlid Neutis N5 is a SoM based on Allwinner H5, has a WiFi & BT
module, DDR3 RAM and eMMC.

- add neutis n5 dtsi file for SoM needs
- add neutis de

arm64: dts: allwinner: new board - Emlid Neutis N5

Emlid Neutis N5 is a SoM based on Allwinner H5, has a WiFi & BT
module, DDR3 RAM and eMMC.

- add neutis n5 dtsi file for SoM needs
- add neutis devboard dts file
- add neutis devboard target to dtb makefile

Signed-off-by: Aleksandr Aleksandrov <aleksandr.aleksandrov@emlid.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

show more ...

ARM: dts: sunxi: h3-h5: Add Bananapi M2+ v1.2 device trees

Bananapi released an updated revision of the H3/H5 based Bananapi M2+.
Version 1.2 enables voltage control for the CPU's regulator by using

ARM: dts: sunxi: h3-h5: Add Bananapi M2+ v1.2 device trees

Bananapi released an updated revision of the H3/H5 based Bananapi M2+.
Version 1.2 enables voltage control for the CPU's regulator by using
a GPIO line to toggle a MOSFET that can change the effective resistance
value in the regulator's feedback network.

This patch adds a common .dtsi file for this new revision, which
includes the original common sunxi-bananapi-m2-plus.dtsi file, and
adds the GPIO-controlled regulator and a cpu-supply reference. H3
and H5 variant dts files are added as well.

Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

show more ...

arm64: dts: allwinner: h5: Add device tree for Bananapi M2 Plus H5

The Bananapi M2 Plus H5 is a variant of the original Bananapi M2 Plus,
with the H3 SoC replaced with an H5. Everything else is the

arm64: dts: allwinner: h5: Add device tree for Bananapi M2 Plus H5

The Bananapi M2 Plus H5 is a variant of the original Bananapi M2 Plus,
with the H3 SoC replaced with an H5. Everything else is the same.

Add a stub device tree incorporating the shared bananapi-m2-plus dtsi
file.

Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

show more ...

arm64: dts: allwinner: h6: Add OrangePi One Plus initial support

OrangePi One Plus is Allwinner H6 based open-source SBC,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T72

arm64: dts: allwinner: h6: Add OrangePi One Plus initial support

OrangePi One Plus is Allwinner H6 based open-source SBC,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB LPDDR3 RAM
- AXP805 PMIC
- 1Gbps GMAC via RTL8211
- USB 2.0 Host, OTG
- HDMI port
- 5V/2A DC power supply

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

show more ...

arm64: dts: allwinner: a64: Add Pine64-LTS device tree file

The Pine64-LTS is a variant of the Pine64 board, from the software
visible side resembling a SoPine module on a baseboard, though the
boar

arm64: dts: allwinner: a64: Add Pine64-LTS device tree file

The Pine64-LTS is a variant of the Pine64 board, from the software
visible side resembling a SoPine module on a baseboard, though the
board has the SoC and DRAM integrated on one PCB.
Due to this it basically shares the DT with the SoPine baseboard, which
we mimic in our DT by inclucing the boardboard .dts into the new file,
just overwriting the model name.
Having a separate .dts for this seems useful, since we don't know yet if
there are subtle differences between the two. Also the SoC on the LTS
board is technically an "R18" instead of the original "A64", although as
far as we know this is just a relabelled version of the original SoC.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

show more ...

arm64: dts: allwinner: add support for Pinebook

Pinebook is a A64-based laptop produced by Pine64, with the following
peripherals:

USB:
- Two external USB ports (one is directly connected to A64's

arm64: dts: allwinner: add support for Pinebook

Pinebook is a A64-based laptop produced by Pine64, with the following
peripherals:

USB:
- Two external USB ports (one is directly connected to A64's OTG
controller, the other is under a internal hub connected to the host-only
controller.)
- USB HID keyboard and touchpad connected to the internal hub.
- USB UVC camera connected to the internal hub.

Power-related:
- A DC IN jack connected to AXP803's DCIN pin.
- A Li-Polymer battery connected to AXP803's battery pins.

Storage:
- An eMMC by Foresee on the main board (in the product revision of the
main board it's designed to be switchable).
- An external MicroSD card slot.

Display:
- An eDP LCD panel (1366x768) connected via an ANX6345 RGB-eDP bridge.
- A mini HDMI port.

Misc:
- A Hall sensor designed to detect the status of lid, connected to GPIO PL12.
- A headphone jack connected to the SoC's internal codec.
- A debug UART port muxed with headphone jack.

This commit adds basical support for it.

[vasily: squashed several commits into one, added simplefb node, added usbphy
to ehci0 and ohci0 nodes and other cosmetic changes to dts]

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

show more ...