ARC: [plat-hsdk]: Remove misplaced interrupt-cells property

[ Upstream commit 61231eb8113ce47991f35024f9c20810b37996bf ]

"gmac" node stands for just an ordinary Ethernet controller,
which is by no

ARC: [plat-hsdk]: Remove misplaced interrupt-cells property

[ Upstream commit 61231eb8113ce47991f35024f9c20810b37996bf ]

"gmac" node stands for just an ordinary Ethernet controller,
which is by no means a provider of interrupts, i.e. it doesn't serve
as an interrupt controller, thus "#interrupt-cells" property doesn't
belong to it and so we remove it.

Fixes:
------------>8------------
DTC arch/arc/boot/dts/hsdk.dtb
arch/arc/boot/dts/hsdk.dts:207.23-235.5: Warning (interrupt_provider): /soc/ethernet@8000: '#interrupt-cells' found, but node is not an interrupt provider
arch/arc/boot/dts/hsdk.dtb: Warning (interrupt_map): Failed prerequisite 'interrupt_provider'
------------>8------------

Reported-by: Vineet Gupta <vgupta@kernel.org>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

ARC: [plat-hsdk]: Remove misplaced interrupt-cells property

[ Upstream commit 61231eb8113ce47991f35024f9c20810b37996bf ]

"gmac" node stands for just an ordinary Ethernet controller,
which is by no

ARC: [plat-hsdk]: Remove misplaced interrupt-cells property

[ Upstream commit 61231eb8113ce47991f35024f9c20810b37996bf ]

"gmac" node stands for just an ordinary Ethernet controller,
which is by no means a provider of interrupts, i.e. it doesn't serve
as an interrupt controller, thus "#interrupt-cells" property doesn't
belong to it and so we remove it.

Fixes:
------------>8------------
DTC arch/arc/boot/dts/hsdk.dtb
arch/arc/boot/dts/hsdk.dts:207.23-235.5: Warning (interrupt_provider): /soc/ethernet@8000: '#interrupt-cells' found, but node is not an interrupt provider
arch/arc/boot/dts/hsdk.dtb: Warning (interrupt_map): Failed prerequisite 'interrupt_provider'
------------>8------------

Reported-by: Vineet Gupta <vgupta@kernel.org>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

ARC: [plat-hsdk]: Remove misplaced interrupt-cells property

[ Upstream commit 61231eb8113ce47991f35024f9c20810b37996bf ]

"gmac" node stands for just an ordinary Ethernet controller,
which is by no

ARC: [plat-hsdk]: Remove misplaced interrupt-cells property

[ Upstream commit 61231eb8113ce47991f35024f9c20810b37996bf ]

"gmac" node stands for just an ordinary Ethernet controller,
which is by no means a provider of interrupts, i.e. it doesn't serve
as an interrupt controller, thus "#interrupt-cells" property doesn't
belong to it and so we remove it.

Fixes:
------------>8------------
DTC arch/arc/boot/dts/hsdk.dtb
arch/arc/boot/dts/hsdk.dts:207.23-235.5: Warning (interrupt_provider): /soc/ethernet@8000: '#interrupt-cells' found, but node is not an interrupt provider
arch/arc/boot/dts/hsdk.dtb: Warning (interrupt_map): Failed prerequisite 'interrupt_provider'
------------>8------------

Reported-by: Vineet Gupta <vgupta@kernel.org>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

arc: dts: Harmonize EHCI/OHCI DT nodes name

In accordance with the Generic EHCI/OHCI bindings the corresponding node
name is suppose to comply with the Generic USB HCD DT schema, which
requires the

arc: dts: Harmonize EHCI/OHCI DT nodes name

In accordance with the Generic EHCI/OHCI bindings the corresponding node
name is suppose to comply with the Generic USB HCD DT schema, which
requires the USB nodes to have the name acceptable by the regexp:
"^usb(@.*)?" . Make sure the "generic-ehci" and "generic-ohci"-compatible
nodes are correctly named.

Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Vineet Gupta <vgupta@kernel.org>

show more ...

ARC: dts: align SPI NOR node name with dtschema

The node names should be generic and SPI NOR dtschema expects "flash".

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off

ARC: dts: align SPI NOR node name with dtschema

The node names should be generic and SPI NOR dtschema expects "flash".

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Vineet Gupta <vgupta@kernel.org>

show more ...

ARC: [plat-hsdk]: Switch ethernet phy-mode to rgmii-id

HSDK board has Micrel KSZ9031, recent commit
bcf3440c6dd ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY")
caused a breakdown of E

ARC: [plat-hsdk]: Switch ethernet phy-mode to rgmii-id

HSDK board has Micrel KSZ9031, recent commit
bcf3440c6dd ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY")
caused a breakdown of Ethernet.
Using 'phy-mode = "rgmii"' is not correct because accodring RGMII
specification it is necessary to have delay on RX (PHY to MAX)
which is not generated in case of "rgmii".
Using "rgmii-id" adds necessary delay and solves the issue.

Also adding name of PHY placed on HSDK board.

Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

show more ...

ARC: HSDK: wireup perf irq

Newer version of HSDK aka HSDK-4xD (with dual issue HS48x4 CPU) wired up
the perf interrupt, so enable that in DT.
This is OK for old HSDK where this irq is ignored becaus

ARC: HSDK: wireup perf irq

Newer version of HSDK aka HSDK-4xD (with dual issue HS48x4 CPU) wired up
the perf interrupt, so enable that in DT.
This is OK for old HSDK where this irq is ignored because pct irq is not
wired up in hardware.

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

show more ...

ARC: [plat-hsdk]: Enable on-boardi SPI ADC IC

HSDK board has adc108s102 SPI ADC IC installed, enable it.

Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Pal

ARC: [plat-hsdk]: Enable on-boardi SPI ADC IC

HSDK board has adc108s102 SPI ADC IC installed, enable it.

Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

show more ...

ARC: [plat-hsdk]: Enable on-board SPI NOR flash IC

HSDK board has sst26wf016b SPI NOR flash IC installed, enable it.

Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Eugeniy Paltsev

ARC: [plat-hsdk]: Enable on-board SPI NOR flash IC

HSDK board has sst26wf016b SPI NOR flash IC installed, enable it.

Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

show more ...

ARC: [plat-hsdk]: enable DW SPI controller

HSDK SoC has DW SPI controller. Enable it in preparation of
enabling on-board SPI peripherals.

Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off

ARC: [plat-hsdk]: enable DW SPI controller

HSDK SoC has DW SPI controller. Enable it in preparation of
enabling on-board SPI peripherals.

Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

show more ...

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500

Based on 2 normalized pattern(s):

this program is free software you can redistribute it and or modify
it under the terms of th

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500

Based on 2 normalized pattern(s):

this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation

this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #

extracted by the scancode license scanner the SPDX license identifier

GPL-2.0-only

has been chosen to replace the boilerplate/reference in 4122 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

ARC: [plat-hsdk] Get rid of inappropriate PHY settings

Initial bring-up of the platform was done on FPGA prototype
where TI's DP83867 PHY was used. And so some specific PHY
options were added.

Just

ARC: [plat-hsdk] Get rid of inappropriate PHY settings

Initial bring-up of the platform was done on FPGA prototype
where TI's DP83867 PHY was used. And so some specific PHY
options were added.

Just to confirm this is what we get on FPGA prototype in the bootlog:
| TI DP83867 stmmac-0:00: attached PHY driver [TI DP83867] ...

On real board though we have Micrel KZS9031 PHY and we even have
CONFIG_MICREL_PHY=y set in hsdk_defconfig. That's what we see in the bootlog:
| Micrel KSZ9031 Gigabit PHY stmmac-0:00: ...

So essentially all TI-related bits have to go away.

Cc: Rob Herring <robh+dt@kernel.org>
Acked-by: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

show more ...

ARC: [plat-hsdk]: Add support of Vivante GPU

HSDK board has built-in Vivante GPU IP which works perfectly fine
with Etnaviv driver, so let's use it.

Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@

ARC: [plat-hsdk]: Add support of Vivante GPU

HSDK board has built-in Vivante GPU IP which works perfectly fine
with Etnaviv driver, so let's use it.

Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

show more ...

ARC: [plat-hsdk]: enable creg-gpio controller

HSDK SOC has CREG GPIO controller which can be used to control
SPI chip select lines.
Enable it in preparation of enabling SPI peripherals.

Acked-by: A

ARC: [plat-hsdk]: enable creg-gpio controller

HSDK SOC has CREG GPIO controller which can be used to control
SPI chip select lines.
Enable it in preparation of enabling SPI peripherals.

Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

show more ...

ARC: [plat-hsdk]: Add missing FIFO size entry in GMAC node

Add the binding for RX/TX fifo size of GMAC node.

Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutla

ARC: [plat-hsdk]: Add missing FIFO size entry in GMAC node

Add the binding for RX/TX fifo size of GMAC node.

Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Tested-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

show more ...

ARC: [plat-hsdk]: Add missing multicast filter bins number to GMAC node

GMAC controller on HSDK boards supports 256 Hash Table size so we need to
add the multicast filter bins property. This allows

ARC: [plat-hsdk]: Add missing multicast filter bins number to GMAC node

GMAC controller on HSDK boards supports 256 Hash Table size so we need to
add the multicast filter bins property. This allows for the Hash filter
to work properly using stmmac driver.

Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

show more ...

ARC: [hsdk] Make it easier to add PAE40 region to DTB

1. Bump top level address-cells/size-cells nodes to 2 (to ensure all
down stream addresses are 64-bits, unless explicitly specified
otherw

ARC: [hsdk] Make it easier to add PAE40 region to DTB

1. Bump top level address-cells/size-cells nodes to 2 (to ensure all
down stream addresses are 64-bits, unless explicitly specified
otherwise (in "soc" bus with all peripherals)

2. "memory" also specified with address/size 2

3. Add a commented reference for PAE40 region beyond 4GB physical
address space

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

show more ...

ARC: [plat-hsdk]: Enable AXI DW DMAC support

Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

ARC: [plat-hsdk]: Add reset controller handle to manage USB reset

DW USB controller on HSDK hangs sometimes after SW reset, so
add reset handle to make possible to reset DW USB controller HW.

Signe

ARC: [plat-hsdk]: Add reset controller handle to manage USB reset

DW USB controller on HSDK hangs sometimes after SW reset, so
add reset handle to make possible to reset DW USB controller HW.

Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

show more ...

ARC: DTB: [scripted] fix node name and address spelling

1. Remove "0x" prefix from unit-address of node names
----------------------->8------------------------
sed -i 's/@0x/@/g' arch/arc/boot/dts/*

ARC: DTB: [scripted] fix node name and address spelling

1. Remove "0x" prefix from unit-address of node names
----------------------->8------------------------
sed -i 's/@0x/@/g' arch/arc/boot/dts/*.dts*
----------------------->8------------------------

2. Make all hex addresses lowercase:
----------------------->8------------------------
sed -i 's/@\([0-9A-Za-z]*\)/@\L\1/g' arch/arc/boot/dts/*.dts*
sed -i 's/0x\([0-9A-Za-z]*\)/0x\L\1/g' arch/arc/boot/dts/*.dts*
----------------------->8------------------------

Inspired by [1] and the like.

[1] http://kisskb.ellerman.id.au/kisskb/buildresult/13612017/

Reviewed-by: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

show more ...

ARC: [plat-hsdk] Enable DW APB GPIO support

Enable GPIO support on HSDK. HSDK SoC includes Synopsys
DesignWare DW_apb_gpio IP with 24 GPIOs mapped onto port A.

Signed-off-by: Eugeniy Paltsev <Eugen

ARC: [plat-hsdk] Enable DW APB GPIO support

Enable GPIO support on HSDK. HSDK SoC includes Synopsys
DesignWare DW_apb_gpio IP with 24 GPIOs mapped onto port A.

Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

show more ...

ARC: dma [IOC]: mark DMA devices connected as dma-coherent

Mark DMA devices on AXS103 and HSDK boards connected through IOC
port as dma-coherent.

Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@syn

ARC: dma [IOC]: mark DMA devices connected as dma-coherent

Mark DMA devices on AXS103 and HSDK boards connected through IOC
port as dma-coherent.

Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

show more ...

ARC: [plat-axs*/plat-hsdk]: Allow U-Boot to pass MAC-address to the kernel

Otherwise kernel uses random MAC which is not very conveniet.
With that change in place use might set desired MAC in U-Boot

ARC: [plat-axs*/plat-hsdk]: Allow U-Boot to pass MAC-address to the kernel

Otherwise kernel uses random MAC which is not very conveniet.
With that change in place use might set desired MAC in U-Boot
with "setenv ethaddr 11:22:33:44:55:66", save environment and
then from boot to boot the same MAC will be used by the kernel.

One other note for this to happen it's required to pass
board's .dtb in U-Boot's "bootm" command like that:
------------------->8-----------------
bootm 0x82000000 - 0x84000000
------------------->8-----------------

Here 0x82000000 is location of uImage while
0x80000000 is location of either axs10x.dtb or hsdk.dtb
previously loaded from SD-card, USB storage or TFTP server.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: stable@vger.kernel.org # 4.14
Cc: devicetree@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

show more ...

ARC: [plat-hsdk]: Set initial core pll output frequency

Set initial core pll output frequency specified in device tree to
1GHz. It will be applied at the core pll driver probing.

Acked-by: Stephen

ARC: [plat-hsdk]: Set initial core pll output frequency

Set initial core pll output frequency specified in device tree to
1GHz. It will be applied at the core pll driver probing.

Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

show more ...

ARC: [plat-hsdk] Increase SDIO CIU frequency to 50000000Hz

With current SDIO CIU clock frequency (12500000Hz) DW MMC
controller fails to initialize some SD cards (which don't
support slow mode).

So

ARC: [plat-hsdk] Increase SDIO CIU frequency to 50000000Hz

With current SDIO CIU clock frequency (12500000Hz) DW MMC
controller fails to initialize some SD cards (which don't
support slow mode).

So increase SDIO CIU frequency from 12500000Hz to 50000000Hz by
switching from the default divisor value (div-by-8) to the
minimum possible value of the divisor (div-by-2) in HSDK platform
code.

Reported-by: Vineet Gupta <vgupta@synopsys.com>
Tested-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

show more ...