pinctrl: amd: Mask non-wake source pins with interrupt enabled at suspend

[ Upstream commit 2fff0b5e1a6b9c577b4dd4958902c877159c856b ]

If a pin isn't marked as a wake source processing any interrup

pinctrl: amd: Mask non-wake source pins with interrupt enabled at suspend

[ Upstream commit 2fff0b5e1a6b9c577b4dd4958902c877159c856b ]

If a pin isn't marked as a wake source processing any interrupts is
just going to destroy battery life. The APU may wake up from a hardware
sleep state to process the interrupt but not return control to the OS.

Mask interrupt for all non-wake source pins at suspend. They'll be
re-enabled at resume.

Reported-and-tested-by: Marcus Aram <marcus+oss@oxar.nl>
Reported-and-tested-by: Mark Herbert <mark.herbert42@gmail.com>
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2812
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20231203032431.30277-3-mario.limonciello@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

pinctrl: amd: Mask wake bits on probe again

Shubhra reports that their laptop is heating up over s2idle. Even though
it's getting into the deepest state, it appears to be having spurious
wakeup even

pinctrl: amd: Mask wake bits on probe again

Shubhra reports that their laptop is heating up over s2idle. Even though
it's getting into the deepest state, it appears to be having spurious
wakeup events.

While debugging a tangential issue with the RTC Carsten reports that recent
6.1.y based kernel face a similar problem.

Looking at acpidump and GPIO register comparisons these spurious wakeup
events are from the GPIO associated with the I2C touchpad on both laptops
and occur even when the touchpad is not marked as a wake source by the
kernel.

This means that the boot firmware has programmed these bits and because
Linux didn't touch them lead to spurious wakeup events from that GPIO.

To fix this issue, restore most of the code that previously would clear all
the bits associated with wakeup sources. This will allow the kernel to only
program the wake up sources that are necessary.

This is similar to what was done previously; but only the wake bits are
cleared by default instead of interrupts and wake bits. If any other
problems are reported then it may make sense to clear interrupts again too.

Cc: Sachi King <nakato@nakato.io>
Cc: stable@vger.kernel.org
Cc: Thorsten Leemhuis <regressions@leemhuis.info>
Fixes: 65f6c7c91cb2 ("pinctrl: amd: Revert "pinctrl: amd: disable and mask interrupts on probe"")
Reported-by: Shubhra Prakash Nandi <email2shubhra@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217754
Reported-by: Carsten Hatger <xmb8dsv4@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217626#c28
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20230818144850.1439-1-mario.limonciello@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

show more ...

pinctrl: amd: Don't show `Invalid config param` errors

On some systems amd_pinconf_set() is called with parameters
0x8 (PIN_CONFIG_DRIVE_PUSH_PULL) or 0x14 (PIN_CONFIG_PERSIST_STATE)
which are not s

pinctrl: amd: Don't show `Invalid config param` errors

On some systems amd_pinconf_set() is called with parameters
0x8 (PIN_CONFIG_DRIVE_PUSH_PULL) or 0x14 (PIN_CONFIG_PERSIST_STATE)
which are not supported by pinctrl-amd.

Don't show an err message when called with an invalid parameter,
downgrade this to debug instead.

Cc: stable@vger.kernel.org # 6.1
Fixes: 635a750d958e1 ("pinctrl: amd: Use amd_pinconf_set() for all config options")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20230717201652.17168-1-mario.limonciello@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

show more ...

pinctrl: amd: Unify debounce handling into amd_pinconf_set()

Debounce handling is done in two different entry points in the driver.
Unify this to make sure that it's always handled the same.

Tested

pinctrl: amd: Unify debounce handling into amd_pinconf_set()

Debounce handling is done in two different entry points in the driver.
Unify this to make sure that it's always handled the same.

Tested-by: Jan Visser <starquake@linuxeverywhere.org>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20230705133005.577-5-mario.limonciello@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

show more ...

pinctrl: amd: Drop pull up select configuration

pinctrl-amd currently tries to program bit 19 of all GPIOs to select
either a 4kΩ or 8hΩ pull up, but this isn't what bit 19 does. Bit
19 is marked a

pinctrl: amd: Drop pull up select configuration

pinctrl-amd currently tries to program bit 19 of all GPIOs to select
either a 4kΩ or 8hΩ pull up, but this isn't what bit 19 does. Bit
19 is marked as reserved, even in the latest platforms documentation.

Drop this programming functionality.

Tested-by: Jan Visser <starquake@linuxeverywhere.org>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20230705133005.577-4-mario.limonciello@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

show more ...

pinctrl: amd: Use amd_pinconf_set() for all config options

On ASUS TUF A16 it is reported that the ITE5570 ACPI device connected to
GPIO 7 is causing an interrupt storm. This issue doesn't happen o

pinctrl: amd: Use amd_pinconf_set() for all config options

On ASUS TUF A16 it is reported that the ITE5570 ACPI device connected to
GPIO 7 is causing an interrupt storm. This issue doesn't happen on
Windows.

Comparing the GPIO register configuration between Windows and Linux
bit 20 has been configured as a pull up on Windows, but not on Linux.
Checking GPIO declaration from the firmware it is clear it *should* have
been a pull up on Linux as well.

```
GpioInt (Level, ActiveLow, Exclusive, PullUp, 0x0000,
"\\_SB.GPIO", 0x00, ResourceConsumer, ,)
{ // Pin list
0x0007
}
```

On Linux amd_gpio_set_config() is currently only used for programming
the debounce. Actually the GPIO core calls it with all the arguments
that are supported by a GPIO, pinctrl-amd just responds `-ENOTSUPP`.

To solve this issue expand amd_gpio_set_config() to support the other
arguments amd_pinconf_set() supports, namely `PIN_CONFIG_BIAS_PULL_DOWN`,
`PIN_CONFIG_BIAS_PULL_UP`, and `PIN_CONFIG_DRIVE_STRENGTH`.

Reported-by: Nik P <npliashechnikov@gmail.com>
Reported-by: Nathan Schulte <nmschulte@gmail.com>
Reported-by: Friedrich Vock <friedrich.vock@gmx.de>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217336
Reported-by: dridri85@gmail.com
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217493
Link: https://lore.kernel.org/linux-input/20230530154058.17594-1-friedrich.vock@gmx.de/
Tested-by: Jan Visser <starquake@linuxeverywhere.org>
Fixes: 2956b5d94a76 ("pinctrl / gpio: Introduce .set_config() callback for GPIO chips")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230705133005.577-3-mario.limonciello@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

show more ...

pinctrl: amd: Only use special debounce behavior for GPIO 0

It's uncommon to use debounce on any other pin, but technically
we should only set debounce to 0 when working off GPIO0.

Cc: stable@vger.

pinctrl: amd: Only use special debounce behavior for GPIO 0

It's uncommon to use debounce on any other pin, but technically
we should only set debounce to 0 when working off GPIO0.

Cc: stable@vger.kernel.org
Tested-by: Jan Visser <starquake@linuxeverywhere.org>
Fixes: 968ab9261627 ("pinctrl: amd: Detect internal GPIO0 debounce handling")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20230705133005.577-2-mario.limonciello@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

show more ...

pinctrl: amd: Use pm_pr_dbg to show debugging messages

To make the GPIO tracking around suspend easier for end users to
use, link it with pm_debug_messages. This will make discovering
sources of sp

pinctrl: amd: Use pm_pr_dbg to show debugging messages

To make the GPIO tracking around suspend easier for end users to
use, link it with pm_debug_messages. This will make discovering
sources of spurious GPIOs around suspend easier.

Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

show more ...

pinctrl: amd: Revert "pinctrl: amd: disable and mask interrupts on probe"

commit 4e5a04be88fe ("pinctrl: amd: disable and mask interrupts on probe")
was well intentioned to mask a firmware issue on

pinctrl: amd: Revert "pinctrl: amd: disable and mask interrupts on probe"

commit 4e5a04be88fe ("pinctrl: amd: disable and mask interrupts on probe")
was well intentioned to mask a firmware issue on a surface laptop, but it
has a few problems:
1. It had a bug in the loop handling for iteration 63 that lead to other
problems with GPIO0 handling.
2. It disables interrupts that are used internally by the SOC but masked
by default.
3. It masked a real firmware problem in some chromebooks that should have
been caught during development but wasn't.

There has been a lot of other development around s2idle; particularly
around handling of the spurious wakeups. If there is still a problem on
the original reported surface laptop it should be avoided by adding a quirk
to gpiolib-acpi for that system instead.

Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20230421120625.3366-5-mario.limonciello@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

show more ...

pinctrl: amd: Detect and mask spurious interrupts

Leverage gpiochip_line_is_irq to check whether a pin has an irq
associated with it. The previous check ("irq == 0") didn't make much
sense. The irq

pinctrl: amd: Detect and mask spurious interrupts

Leverage gpiochip_line_is_irq to check whether a pin has an irq
associated with it. The previous check ("irq == 0") didn't make much
sense. The irq variable refers to the pinctrl irq, and has nothing do to
with an individual pin.

On some systems, during suspend/resume cycle, the firmware leaves
an interrupt enabled on a pin that is not used by the kernel.
Without this patch that caused an interrupt storm.

Cc: stable@vger.kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217315
Signed-off-by: Kornel Dulęba <korneld@chromium.org>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20230421120625.3366-4-mario.limonciello@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

show more ...

pinctrl: amd: Fix mistake in handling clearing pins at startup

commit 4e5a04be88fe ("pinctrl: amd: disable and mask interrupts on probe")
had a mistake in loop iteration 63 that it would clear offse

pinctrl: amd: Fix mistake in handling clearing pins at startup

commit 4e5a04be88fe ("pinctrl: amd: disable and mask interrupts on probe")
had a mistake in loop iteration 63 that it would clear offset 0xFC instead
of 0x100. Offset 0xFC is actually `WAKE_INT_MASTER_REG`. This was
clearing bits 13 and 15 from the register which significantly changed the
expected handling for some platforms for GPIO0.

Cc: stable@vger.kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217315
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20230421120625.3366-3-mario.limonciello@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

show more ...

pinctrl: amd: Detect internal GPIO0 debounce handling

commit 4e5a04be88fe ("pinctrl: amd: disable and mask interrupts on probe")
had a mistake in loop iteration 63 that it would clear offset 0xFC in

pinctrl: amd: Detect internal GPIO0 debounce handling

commit 4e5a04be88fe ("pinctrl: amd: disable and mask interrupts on probe")
had a mistake in loop iteration 63 that it would clear offset 0xFC instead
of 0x100. Offset 0xFC is actually `WAKE_INT_MASTER_REG`. This was
clearing bits 13 and 15 from the register which significantly changed the
expected handling for some platforms for GPIO0.

commit b26cd9325be4 ("pinctrl: amd: Disable and mask interrupts on resume")
actually fixed this bug, but lead to regressions on Lenovo Z13 and some
other systems. This is because there was no handling in the driver for bit
15 debounce behavior.

Quoting a public BKDG:
```
EnWinBlueBtn. Read-write. Reset: 0. 0=GPIO0 detect debounced power button;
Power button override is 4 seconds. 1=GPIO0 detect debounced power button
in S3/S5/S0i3, and detect "pressed less than 2 seconds" and "pressed 2~10
seconds" in S0; Power button override is 10 seconds
```

Cross referencing the same master register in Windows it's obvious that
Windows doesn't use debounce values in this configuration. So align the
Linux driver to do this as well. This fixes wake on lid when
WAKE_INT_MASTER_REG is properly programmed.

Cc: stable@vger.kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217315
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20230421120625.3366-2-mario.limonciello@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

show more ...

pinctrl: amd: remove MODULE_LICENSE in non-modules

Since commit 8b41fc4454e ("kbuild: create modules.builtin without
Makefile.modbuiltin or tristate.conf"), MODULE_LICENSE declarations
are used to i

pinctrl: amd: remove MODULE_LICENSE in non-modules

Since commit 8b41fc4454e ("kbuild: create modules.builtin without
Makefile.modbuiltin or tristate.conf"), MODULE_LICENSE declarations
are used to identify modules. As a consequence, uses of the macro
in non-modules will cause modprobe to misidentify their containing
object file as a module when it is not (false positives), and modprobe
might succeed rather than failing with a suitable error message.

So remove it in the files in this commit, none of which can be built as
modules.

Signed-off-by: Nick Alcock <nick.alcock@oracle.com>
Suggested-by: Luis Chamberlain <mcgrof@kernel.org>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: linux-modules@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Hitomi Hasegawa <hasegawa-hitomi@fujitsu.com>
Cc: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Cc: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>

show more ...

Revert "pinctrl: amd: Disable and mask interrupts on resume"

This reverts commit b26cd9325be4c1fcd331b77f10acb627c560d4d7.

This patch introduces a regression on Lenovo Z13, which can't wake
from th

Revert "pinctrl: amd: Disable and mask interrupts on resume"

This reverts commit b26cd9325be4c1fcd331b77f10acb627c560d4d7.

This patch introduces a regression on Lenovo Z13, which can't wake
from the lid with it applied; and some unspecified AMD based Dell
platforms are unable to wake from hitting the power button

Signed-off-by: Kornel Dulęba <korneld@chromium.org>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20230411134932.292287-1-korneld@chromium.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

show more ...

pinctrl: amd: Add fields for interrupt status and wake status

If the firmware has misconfigured a GPIO it may cause interrupt
status or wake status bits to be set and not asserted. Add these
to debu

pinctrl: amd: Add fields for interrupt status and wake status

If the firmware has misconfigured a GPIO it may cause interrupt
status or wake status bits to be set and not asserted. Add these
to debug output to catch this case.

Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20230328174231.8924-3-mario.limonciello@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

show more ...

pinctrl: amd: Adjust debugfs output

More fields are to be added, so to keep the display from being
too busy, adjust it.

1) Add a header to all columns
2) Except for interrupt, when fields have no d

pinctrl: amd: Adjust debugfs output

More fields are to be added, so to keep the display from being
too busy, adjust it.

1) Add a header to all columns
2) Except for interrupt, when fields have no data show empty
3) Remove otherwise blank whitespace

Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20230328174231.8924-2-mario.limonciello@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

show more ...

pinctrl: amd: Disable and mask interrupts on resume

This fixes a similar problem to the one observed in:
commit 4e5a04be88fe ("pinctrl: amd: disable and mask interrupts on probe").

On some systems,

pinctrl: amd: Disable and mask interrupts on resume

This fixes a similar problem to the one observed in:
commit 4e5a04be88fe ("pinctrl: amd: disable and mask interrupts on probe").

On some systems, during suspend/resume cycle firmware leaves
an interrupt enabled on a pin that is not used by the kernel.
This confuses the AMD pinctrl driver and causes spurious interrupts.

The driver already has logic to detect if a pin is used by the kernel.
Leverage it to re-initialize interrupt fields of a pin only if it's not
used by us.

Cc: stable@vger.kernel.org
Fixes: dbad75dd1f25 ("pinctrl: add AMD GPIO driver support.")
Signed-off-by: Kornel Dulęba <korneld@chromium.org>
Link: https://lore.kernel.org/r/20230320093259.845178-1-korneld@chromium.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

show more ...

pinctrl: amd: Fix debug output for debounce time

If one GPIO has debounce enabled but future GPIOs in the list don't
have debounce the time never gets reset and shows wrong value.

Signed-off-by: Ma

pinctrl: amd: Fix debug output for debounce time

If one GPIO has debounce enabled but future GPIOs in the list don't
have debounce the time never gets reset and shows wrong value.

Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20230121134812.16637-2-mario.limonciello@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

show more ...

pinctrl: amd: Add Z-state wake control bits

GPIO registers include Bit 27 for WakeCntrlZ used to enable wake in
Z state. Hence add Z-state wake control bits to debugfs output to
debug and analyze Z-

pinctrl: amd: Add Z-state wake control bits

GPIO registers include Bit 27 for WakeCntrlZ used to enable wake in
Z state. Hence add Z-state wake control bits to debugfs output to
debug and analyze Z-states problems.

Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Suggested-by: Mario Limonciello <mario.limonciello@amd.com>
Tested-by: Guruvendra Punugupati <Guruvendra.Punugupati@amd.com>
Link: https://lore.kernel.org/r/20221208093704.1151928-1-Basavaraj.Natikar@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

show more ...

pinctrl: amd: Add dynamic debugging for active GPIOs

Some laptops have been reported to wake up from s2idle when plugging
in the AC adapter or by closing the lid. This is a surprising
behavior that

pinctrl: amd: Add dynamic debugging for active GPIOs

Some laptops have been reported to wake up from s2idle when plugging
in the AC adapter or by closing the lid. This is a surprising
behavior that is further clarified by commit cb3e7d624c3ff ("PM:
wakeup: Add extra debugging statement for multiple active IRQs").

With that commit in place the following interaction can be seen
when the lid is closed:

[ 28.946038] PM: suspend-to-idle
[ 28.946083] ACPI: EC: ACPI EC GPE status set
[ 28.946101] ACPI: PM: Rearming ACPI SCI for wakeup
[ 28.950152] Timekeeping suspended for 3.320 seconds
[ 28.950152] PM: Triggering wakeup from IRQ 9
[ 28.950152] ACPI: EC: ACPI EC GPE status set
[ 28.950152] ACPI: EC: ACPI EC GPE dispatched
[ 28.995057] ACPI: EC: ACPI EC work flushed
[ 28.995075] ACPI: PM: Rearming ACPI SCI for wakeup
[ 28.995131] PM: Triggering wakeup from IRQ 9
[ 28.995271] ACPI: EC: ACPI EC GPE status set
[ 28.995291] ACPI: EC: ACPI EC GPE dispatched
[ 29.098556] ACPI: EC: ACPI EC work flushed
[ 29.207020] ACPI: EC: ACPI EC work flushed
[ 29.207037] ACPI: PM: Rearming ACPI SCI for wakeup
[ 29.211095] Timekeeping suspended for 0.739 seconds
[ 29.211095] PM: Triggering wakeup from IRQ 9
[ 29.211079] PM: Triggering wakeup from IRQ 7
[ 29.211095] ACPI: PM: ACPI non-EC GPE wakeup
[ 29.211095] PM: resume from suspend-to-idle

* IRQ9 on this laptop is used for the ACPI SCI.
* IRQ7 on this laptop is used for the GPIO controller.

What has occurred is when the lid was closed the EC woke up the
SoC from it's deepest sleep state and the kernel's s2idle loop
processed all EC events. When it was finished processing EC events,
it checked for any other reasons to wake (break the s2idle loop).

The IRQ for the GPIO controller was active so the loop broke, and
then this IRQ was processed. This is not a kernel bug but it is
certainly a surprising behavior, and to better debug it we should
have a dynamic debugging message that we can enact to catch it.

Acked-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Acked-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Acked-by: Mark Pearson <markpearson@lenovo.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20221013134729.5592-2-mario.limonciello@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

show more ...

pinctrl: amd: Use generic_handle_irq_safe()

On PREEMPT_RT enabled kernels the demultiplex interrupt handler is force
threaded and runs with interrupts enabled. The invocation of
generic_handle_domai

pinctrl: amd: Use generic_handle_irq_safe()

On PREEMPT_RT enabled kernels the demultiplex interrupt handler is force
threaded and runs with interrupts enabled. The invocation of
generic_handle_domain_irq() with interrupts enabled triggers a lockdep
warning due to a non-irq safe lock acquisition.

Instead of disabling interrupts on the driver level, use
generic_handle_domain_irq_safe().

[ tglx: Split out from combo patch ]

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/YnkfWFzvusFFktSt@linutronix.de
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215954

show more ...

pinctrl: amd: change dev_warn to dev_dbg for additional feature support

Use dev_dbg instead of dev_warn for additional support of pinmux
feature.

Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar

pinctrl: amd: change dev_warn to dev_dbg for additional feature support

Use dev_dbg instead of dev_warn for additional support of pinmux
feature.

Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Link: https://lore.kernel.org/r/20220830110525.1933198-1-Basavaraj.Natikar@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

show more ...

pinctrl: amd: Pick some different unicode symbols

Feedback from Kent had showed some better selections for symbols to
use for pinctrl-amd debugfs output. Adopt some of those instead.

Fixes: e8129a

pinctrl: amd: Pick some different unicode symbols

Feedback from Kent had showed some better selections for symbols to
use for pinctrl-amd debugfs output. Adopt some of those instead.

Fixes: e8129a076a50 ("pinctrl: amd: Use unicode for debugfs output")
Suggested-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20220823230753.14799-1-mario.limonciello@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

show more ...

pinctrl: amd: Fix an unused variable

`char *output_enable` is no longer used once switching to unicode
output.

Fixes: e8129a076a50 ("pinctrl: amd: Use unicode for debugfs output")
Reported-by: kern

pinctrl: amd: Fix an unused variable

`char *output_enable` is no longer used once switching to unicode
output.

Fixes: e8129a076a50 ("pinctrl: amd: Use unicode for debugfs output")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20220801144952.141-1-mario.limonciello@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

show more ...

pinctrl: amd: Use unicode for debugfs output

The output is currently split across two lines making it more
difficult to parse unless the newlines are removed between pins
or it's read in by a parser

pinctrl: amd: Use unicode for debugfs output

The output is currently split across two lines making it more
difficult to parse unless the newlines are removed between pins
or it's read in by a parser like Libreoffice Calc or Google docs.

To make it easier to follow to the naked eye in a terminal window:
* drop the newline in the middle of pin definitions
* shorten all output using unicode characters
* align all pipe delimitters
* output the same phrase even for disabled functions
(but with a ∅ character)

Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20220722220810.28894-2-mario.limonciello@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

show more ...