net: phy: micrel: Add config_init for LAN8814

Add config_init for LAN8814. This function is required for the following
reasons:
- we need to make sure that the PHY is reset,
- disable ANEG with QSGM

net: phy: micrel: Add config_init for LAN8814

Add config_init for LAN8814. This function is required for the following
reasons:
- we need to make sure that the PHY is reset,
- disable ANEG with QSGMII PCS Host side
- swap the MDI-X A,B transmit so that there will not be any link flip-flaps
when the PHY gets a link.

Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: micrel: Adding interrupt support for Link up/Link down in LAN8814 Quad phy

This patch add support for Link up or Link down
interrupt support in LAN8814 Quad phy

Signed-off-by: Divya Koppe

net: phy: micrel: Adding interrupt support for Link up/Link down in LAN8814 Quad phy

This patch add support for Link up or Link down
interrupt support in LAN8814 Quad phy

Signed-off-by: Divya Koppera <Divya.Koppera@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20211221112217.9502-1-Divya.Koppera@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

phy: micrel: ksz8041nl: do not use power down mode

Some Micrel KSZ8041NL PHY chips exhibit continuous RX errors after using
the power down mode bit (0.11). If the PHY is taken out of power down
mode

phy: micrel: ksz8041nl: do not use power down mode

Some Micrel KSZ8041NL PHY chips exhibit continuous RX errors after using
the power down mode bit (0.11). If the PHY is taken out of power down
mode in a certain temperature range, the PHY enters a weird state which
leads to continuously reporting RX errors. In that state, the MAC is not
able to receive or send any Ethernet frames and the activity LED is
constantly blinking. Since Linux is using the suspend callback when the
interface is taken down, ending up in that state can easily happen
during a normal startup.

Micrel confirmed the issue in errata DS80000700A [*], caused by abnormal
clock recovery when using power down mode. Even the latest revision (A4,
Revision ID 0x1513) seems to suffer that problem, and according to the
errata is not going to be fixed.

Remove the suspend/resume callback to avoid using the power down mode
completely.

[*] https://ww1.microchip.com/downloads/en/DeviceDoc/80000700A.pdf

Fixes: 1a5465f5d6a2 ("phy/micrel: Add suspend/resume support to Micrel PHYs")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: micrel: make *-skew-ps check more lenient

It seems reasonable to fine-tune only some of the skew values when using
one of the rgmii-*id PHY modes, and even when all skew values are
specifi

net: phy: micrel: make *-skew-ps check more lenient

It seems reasonable to fine-tune only some of the skew values when using
one of the rgmii-*id PHY modes, and even when all skew values are
specified, using the correct ID PHY mode makes sense for documentation
purposes. Such a configuration also appears in the binding docs in
Documentation/devicetree/bindings/net/micrel-ksz90x1.txt, so the driver
should not warn about it.

Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20211012103402.21438-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

net: phy: micrel: ksz9131 led errata workaround

Micrel KSZ9131 PHY LED behavior is not correct when configured in
Individual Mode, LED1 (Activity LED) is in the ON state when there is
no-link.

Work

net: phy: micrel: ksz9131 led errata workaround

Micrel KSZ9131 PHY LED behavior is not correct when configured in
Individual Mode, LED1 (Activity LED) is in the ON state when there is
no-link.

Workaround this by setting bit 9 of register 0x1e after verifying that
the LED configuration is Individual Mode.

This issue is described in KSZ9131RNX Silicon Errata DS80000693B [*]
and according to that it will not be corrected in a future silicon
revision.

[*] https://ww1.microchip.com/downloads/en/DeviceDoc/KSZ9131RNX-Silicon-Errata-and-Data-Sheet-Clarification-80000863B.pdf

Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: micrel: Add support for LAN8804 PHY

The LAN8804 PHY has same features as that of LAN8814 PHY except that it
doesn't support 1588, SyncE or Q-USGMII.

This PHY is found inside the LAN966X s

net: phy: micrel: Add support for LAN8804 PHY

The LAN8804 PHY has same features as that of LAN8814 PHY except that it
doesn't support 1588, SyncE or Q-USGMII.

This PHY is found inside the LAN966X switches.

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: micrel: Allow probing without .driver_data

[ Upstream commit f2ef6f7539c68c6bd6c32323d8845ee102b7c450 ]

Currently, if the .probe element is present in the phy_driver structure
and the .dr

net: phy: micrel: Allow probing without .driver_data

[ Upstream commit f2ef6f7539c68c6bd6c32323d8845ee102b7c450 ]

Currently, if the .probe element is present in the phy_driver structure
and the .driver_data is not, a NULL pointer dereference happens.

Allow passing .probe without .driver_data by inserting NULL checks
for priv->type.

Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220513114613.762810-1-festevam@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

net: phy: micrel: Allow probing without .driver_data

[ Upstream commit f2ef6f7539c68c6bd6c32323d8845ee102b7c450 ]

Currently, if the .probe element is present in the phy_driver structure
and the .dr

net: phy: micrel: Allow probing without .driver_data

[ Upstream commit f2ef6f7539c68c6bd6c32323d8845ee102b7c450 ]

Currently, if the .probe element is present in the phy_driver structure
and the .driver_data is not, a NULL pointer dereference happens.

Allow passing .probe without .driver_data by inserting NULL checks
for priv->type.

Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220513114613.762810-1-festevam@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

net: phy: micrel: Pass .probe for KS8737

commit 15f03ffe4bb951e982457f44b6cf6b06ef4cbb93 upstream.

Since commit f1131b9c23fb ("net: phy: micrel: use
kszphy_suspend()/kszphy_resume for irq aware dev

net: phy: micrel: Pass .probe for KS8737

commit 15f03ffe4bb951e982457f44b6cf6b06ef4cbb93 upstream.

Since commit f1131b9c23fb ("net: phy: micrel: use
kszphy_suspend()/kszphy_resume for irq aware devices") the kszphy_suspend/
resume hooks are used.

These functions require the probe function to be called so that
priv can be allocated.

Otherwise, a NULL pointer dereference happens inside
kszphy_config_reset().

Cc: stable@vger.kernel.org
Fixes: f1131b9c23fb ("net: phy: micrel: use kszphy_suspend()/kszphy_resume for irq aware devices")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220504143104.1286960-2-festevam@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

net: phy: micrel: Do not use kszphy_suspend/resume for KSZ8061

commit e333eed63a091a09bd0db191b7710c594c6e995b upstream.

Since commit f1131b9c23fb ("net: phy: micrel: use
kszphy_suspend()/kszphy_re

net: phy: micrel: Do not use kszphy_suspend/resume for KSZ8061

commit e333eed63a091a09bd0db191b7710c594c6e995b upstream.

Since commit f1131b9c23fb ("net: phy: micrel: use
kszphy_suspend()/kszphy_resume for irq aware devices") the following
NULL pointer dereference is observed on a board with KSZ8061:

# udhcpc -i eth0
udhcpc: started, v1.35.0
8<--- cut here ---
Unable to handle kernel NULL pointer dereference at virtual address 00000008
pgd = f73cef4e
[00000008] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 196 Comm: ifconfig Not tainted 5.15.37-dirty #94
Hardware name: Freescale i.MX6 SoloX (Device Tree)
PC is at kszphy_config_reset+0x10/0x114
LR is at kszphy_resume+0x24/0x64
...

The KSZ8061 phy_driver structure does not have the .probe/..driver_data
fields, which means that priv is not allocated.

This causes the NULL pointer dereference inside kszphy_config_reset().

Fix the problem by using the generic suspend/resume functions as before.

Another alternative would be to provide the .probe and .driver_data
information into the structure, but to be on the safe side, let's
just restore Ethernet functionality by using the generic suspend/resume.

Cc: stable@vger.kernel.org
Fixes: f1131b9c23fb ("net: phy: micrel: use kszphy_suspend()/kszphy_resume for irq aware devices")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220504143104.1286960-1-festevam@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

net: phy: micrel: use kszphy_suspend()/kszphy_resume for irq aware devices

commit f1131b9c23fb4a3540a774828ff49f421619f902 upstream.

On a setup with KSZ9131 and MACB drivers it happens on suspend p

net: phy: micrel: use kszphy_suspend()/kszphy_resume for irq aware devices

commit f1131b9c23fb4a3540a774828ff49f421619f902 upstream.

On a setup with KSZ9131 and MACB drivers it happens on suspend path, from
time to time, that the PHY interrupt arrives after PHY and MACB were
suspended (PHY via genphy_suspend(), MACB via macb_suspend()). In this
case the phy_read() at the beginning of kszphy_handle_interrupt() will
fail (as MACB driver is suspended at this time) leading to phy_error()
being called and a stack trace being displayed on console. To solve this
.suspend/.resume functions for all KSZ devices implementing
.handle_interrupt were replaced with kszphy_suspend()/kszphy_resume()
which disable/enable interrupt before/after calling
genphy_suspend()/genphy_resume().

The fix has been adapted for all KSZ devices which implements
.handle_interrupt but it has been tested only on KSZ9131.

Fixes: 59ca4e58b917 ("net: phy: micrel: implement generic .handle_interrupt() callback")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

phy: micrel: ksz8041nl: do not use power down mode

[ Upstream commit 2641b62d2fab52648e34cdc6994b2eacde2d27c1 ]

Some Micrel KSZ8041NL PHY chips exhibit continuous RX errors after using
the power do

phy: micrel: ksz8041nl: do not use power down mode

[ Upstream commit 2641b62d2fab52648e34cdc6994b2eacde2d27c1 ]

Some Micrel KSZ8041NL PHY chips exhibit continuous RX errors after using
the power down mode bit (0.11). If the PHY is taken out of power down
mode in a certain temperature range, the PHY enters a weird state which
leads to continuously reporting RX errors. In that state, the MAC is not
able to receive or send any Ethernet frames and the activity LED is
constantly blinking. Since Linux is using the suspend callback when the
interface is taken down, ending up in that state can easily happen
during a normal startup.

Micrel confirmed the issue in errata DS80000700A [*], caused by abnormal
clock recovery when using power down mode. Even the latest revision (A4,
Revision ID 0x1513) seems to suffer that problem, and according to the
errata is not going to be fixed.

Remove the suspend/resume callback to avoid using the power down mode
completely.

[*] https://ww1.microchip.com/downloads/en/DeviceDoc/80000700A.pdf

Fixes: 1a5465f5d6a2 ("phy/micrel: Add suspend/resume support to Micrel PHYs")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

net: phy: micrel: make *-skew-ps check more lenient

[ Upstream commit 67ca5159dbe2edb5dae7544447b8677d2596933a ]

It seems reasonable to fine-tune only some of the skew values when using
one of the

net: phy: micrel: make *-skew-ps check more lenient

[ Upstream commit 67ca5159dbe2edb5dae7544447b8677d2596933a ]

It seems reasonable to fine-tune only some of the skew values when using
one of the rgmii-*id PHY modes, and even when all skew values are
specified, using the correct ID PHY mode makes sense for documentation
purposes. Such a configuration also appears in the binding docs in
Documentation/devicetree/bindings/net/micrel-ksz90x1.txt, so the driver
should not warn about it.

Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20211012103402.21438-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

net: phy: micrel: Fix link detection on ksz87xx switch"

Commit a5e63c7d38d5 "net: phy: micrel: Fix detection of ksz87xx
switch" broke link detection on the external ports of the KSZ8795.

The previo

net: phy: micrel: Fix link detection on ksz87xx switch"

Commit a5e63c7d38d5 "net: phy: micrel: Fix detection of ksz87xx
switch" broke link detection on the external ports of the KSZ8795.

The previously unused phy_driver structure for these devices specifies
config_aneg and read_status functions that appear to be designed for a
fixed link and do not work with the embedded PHYs in the KSZ8795.

Delete the use of these functions in favour of the generic PHY
implementations which were used previously.

Fixes: a5e63c7d38d5 ("net: phy: micrel: Fix detection of ksz87xx switch")
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: micrel: Fix detection of ksz87xx switch

The logic for discerning between KSZ8051 and KSZ87XX PHYs is incorrect
such that the that KSZ87XX switch is not identified correctly.

ksz8051_ksz87

net: phy: micrel: Fix detection of ksz87xx switch

The logic for discerning between KSZ8051 and KSZ87XX PHYs is incorrect
such that the that KSZ87XX switch is not identified correctly.

ksz8051_ksz8795_match_phy_device() uses the parameter ksz_phy_id
to discriminate whether it was called from ksz8051_match_phy_device()
or from ksz8795_match_phy_device() but since PHY_ID_KSZ87XX is the
same value as PHY_ID_KSZ8051, this doesn't work.

Instead use a bool to discriminate the caller.

Without this patch, the KSZ8795 switch port identifies as:

ksz8795-switch spi3.1 ade1 (uninitialized): PHY [dsa-0.1:03] driver [Generic PHY]

With the patch, it identifies correctly:

ksz8795-switch spi3.1 ade1 (uninitialized): PHY [dsa-0.1:03] driver [Micrel KSZ87XX Switch]

Fixes: 8b95599c55ed24b36cf4 ("net: phy: micrel: Discern KSZ8051 and KSZ8795 PHYs")
Signed-off-by: Steve Bennett <steveb@workware.net.au>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: micrel: ksz886x/ksz8081: add cabletest support

This patch support for cable test for the ksz886x switches and the
ksz8081 PHY.

The patch was tested on a KSZ8873RLL switch with following r

net: phy: micrel: ksz886x/ksz8081: add cabletest support

This patch support for cable test for the ksz886x switches and the
ksz8081 PHY.

The patch was tested on a KSZ8873RLL switch with following results:

- port 1:
- provides invalid values, thus return -ENOTSUPP
(Errata: DS80000830A: "LinkMD does not work on Port 1",
http://ww1.microchip.com/downloads/en/DeviceDoc/KSZ8873-Errata-DS80000830A.pdf)

- port 2:
- can detect distance
- can detect open on each wire of pair A (wire 1 and 2)
- can detect open only on one wire of pair B (only wire 3)
- can detect short between wires of a pair (wires 1 + 2 or 3 + 6)
- short between pairs is detected as open.
For example short between wires 2 + 3 is detected as open.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: micrel: ksz8081 add MDI-X support

Add support for MDI-X status and configuration

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed

net: phy: micrel: ksz8081 add MDI-X support

Add support for MDI-X status and configuration

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy/dsa micrel/ksz886x add MDI-X support

Add support for MDI-X status and configuration

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Review

net: phy/dsa micrel/ksz886x add MDI-X support

Add support for MDI-X status and configuration

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: micrel: use consistent alignments

This patch changes the alignments to one space between "#define" and the
macro.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vlad

net: phy: micrel: use consistent alignments

This patch changes the alignments to one space between "#define" and the
macro.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: micrel: remove redundant assignment to pointer of_node

The pointer of_node is being initialized with a value that is never
read and it is being updated later with a new value inside a do-w

net: phy: micrel: remove redundant assignment to pointer of_node

The pointer of_node is being initialized with a value that is never
read and it is being updated later with a new value inside a do-while
loop. The initialization is redundant and can be removed and the
pointer dev is no longer required and can be removed too.

Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: micrel: set soft_reset callback to genphy_soft_reset for KSZ8081

Following a similar reinstate for the KSZ9031.

Older kernels would use the genphy_soft_reset if the PHY did not implement

net: phy: micrel: set soft_reset callback to genphy_soft_reset for KSZ8081

Following a similar reinstate for the KSZ9031.

Older kernels would use the genphy_soft_reset if the PHY did not implement
a .soft_reset.

Bluntly removing that default may expose a lot of situations where various
PHYs/board implementations won't recover on various changes.
Like with this implementation during a 4.9.x to 5.4.x LTS transition.
I think it's a good thing to remove unwanted soft resets but wonder if it
did open a can of worms?

Atleast this fixes one iMX6 FEC/RMII/8081 combo.

Fixes: 6e2d85ec0559 ("net: phy: Stop with excessive soft reset")
Signed-off-by: Christian Melki <christian.melki@t2data.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210224205536.9349-1-christian.melki@t2data.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

net: phy: introduce phydev->port

At the moment, PORT_MII is reported in the ethtool ops. This is odd
because it is an interface between the MAC and the PHY and no external
port. Some network card dr

net: phy: introduce phydev->port

At the moment, PORT_MII is reported in the ethtool ops. This is odd
because it is an interface between the MAC and the PHY and no external
port. Some network card drivers will overwrite the port to twisted pair
or fiber, though. Even worse, the MDI/MDIX setting is only used by
ethtool if the port is twisted pair.

Set the port to PORT_TP by default because most PHY drivers are copper
ones. If there is fibre support and it is enabled, the PHY driver will
set it to PORT_FIBRE.

This will change reporting PORT_MII to either PORT_TP or PORT_FIBRE;
except for the genphy fallback driver.

Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: drop explicit genphy_read_status() op

genphy_read_status() is already the default for the .read_status() op.
Drop the unnecessary references.

Signed-off-by: Michael Walle <michael@walle.c

net: phy: drop explicit genphy_read_status() op

genphy_read_status() is already the default for the .read_status() op.
Drop the unnecessary references.

Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: micrel: Add KS8851 PHY support

The KS8851 has a reduced internal PHY, which is accessible through its
registers at offset 0xe4. The PHY is compatible with KS886x PHY present
in Micrel swit

net: phy: micrel: Add KS8851 PHY support

The KS8851 has a reduced internal PHY, which is accessible through its
registers at offset 0xe4. The PHY is compatible with KS886x PHY present
in Micrel switches, including the PHY ID Low/High registers swap, which
is present both in the MAC and the switch.

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Lukas Wunner <lukas@wunner.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: micrel: fix interrupt handling

After migration to the shared interrupt support, the KSZ8031 PHY with
enabled interrupt support was not able to notify about link status
change.

Fixes: 59ca

net: phy: micrel: fix interrupt handling

After migration to the shared interrupt support, the KSZ8031 PHY with
enabled interrupt support was not able to notify about link status
change.

Fixes: 59ca4e58b917 ("net: phy: micrel: implement generic .handle_interrupt() callback")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201127123621.31234-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...