net: phy: Micrel KSZ8061: fix errata solution not taking effect problem

[ Upstream commit 0a8d3f2e3e8d8aea8af017e14227b91d5989b696 ]

KSZ8061 needs to write to a MMD register at driver initializatio

net: phy: Micrel KSZ8061: fix errata solution not taking effect problem

[ Upstream commit 0a8d3f2e3e8d8aea8af017e14227b91d5989b696 ]

KSZ8061 needs to write to a MMD register at driver initialization to fix
an errata. This worked in 5.0 kernel but not in newer kernels. The
issue is the main phylib code no longer resets PHY at the very beginning.
Calling phy resuming code later will reset the chip if it is already
powered down at the beginning. This wipes out the MMD register write.
Solution is to implement a phy resume function for KSZ8061 to take care
of this problem.

Fixes: 232ba3a51cc2 ("net: phy: Micrel KSZ8061: link failure after cable connect")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

net: phy: micrel: fix KSZ9477 PHY issues after suspend/resume

[ Upstream commit 6149db4997f582e958da675092f21c666e3b67b7 ]

When the PHY is powered up after powered down most of the registers are
re

net: phy: micrel: fix KSZ9477 PHY issues after suspend/resume

[ Upstream commit 6149db4997f582e958da675092f21c666e3b67b7 ]

When the PHY is powered up after powered down most of the registers are
reset, so the PHY setup code needs to be done again. In addition the
interrupt register will need to be setup again so that link status
indication works again.

Fixes: 26dd2974c5b5 ("net: phy: micrel: Move KSZ9477 errata fixes to PHY driver")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

net: micrel: Fix lan8841_config_intr after getting out of sleep mode

[ Upstream commit 4fb679040d9f758eeb3b4d01bbde6405bf20e64e ]

When the interrupt is enabled, the function lan8841_config_intr tri

net: micrel: Fix lan8841_config_intr after getting out of sleep mode

[ Upstream commit 4fb679040d9f758eeb3b4d01bbde6405bf20e64e ]

When the interrupt is enabled, the function lan8841_config_intr tries to
clear any pending interrupts by reading the interrupt status, then
checks the return value for errors and then continue to enable the
interrupt. It has been seen that once the system gets out of sleep mode,
the interrupt status has the value 0x400 meaning that the PHY detected
that the link was in low power. That is correct value but the problem is
that the check is wrong. We try to check for errors but we return an
error also in this case which is not an error. Therefore fix this by
returning only when there is an error.

Fixes: a8f1a19d27ef ("net: micrel: Add support for lan8841 PHY")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Suman Ghosh <sumang@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240524085350.359812-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

net: phy: micrel: set soft_reset callback to genphy_soft_reset for KSZ8061

[ Upstream commit 128d54fbcb14b8717ecf596d3dbded327b9980b3 ]

Following a similar reinstate for the KSZ8081 and KSZ9031.

O

net: phy: micrel: set soft_reset callback to genphy_soft_reset for KSZ8061

[ Upstream commit 128d54fbcb14b8717ecf596d3dbded327b9980b3 ]

Following a similar reinstate for the KSZ8081 and KSZ9031.

Older kernels would use the genphy_soft_reset if the PHY did not implement
a .soft_reset.

The KSZ8061 errata described here:
https://ww1.microchip.com/downloads/en/DeviceDoc/KSZ8061-Errata-DS80000688B.pdf
and worked around with 232ba3a51c ("net: phy: Micrel KSZ8061: link failure after cable connect")
is back again without this soft reset.

Fixes: 6e2d85ec0559 ("net: phy: Stop with excessive soft reset")
Tested-by: Karim Ben Houcine <karim.benhoucine@landisgyr.com>
Signed-off-by: Mathieu Othacehe <othacehe@gnu.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

net: micrel: Fix receiving the timestamp in the frame for lan8841

[ Upstream commit aea27a92a41dae14843f92c79e9e42d8f570105c ]

The blamed commit started to use the ptp workqueue to get the second
p

net: micrel: Fix receiving the timestamp in the frame for lan8841

[ Upstream commit aea27a92a41dae14843f92c79e9e42d8f570105c ]

The blamed commit started to use the ptp workqueue to get the second
part of the timestamp. And when the port was set down, then this
workqueue is stopped. But if the config option NETWORK_PHY_TIMESTAMPING
is not enabled, then the ptp_clock is not initialized so then it would
crash when it would try to access the delayed work.
So then basically by setting up and then down the port, it would crash.
The fix consists in checking if the ptp_clock is initialized and only
then cancel the delayed work.

Fixes: cc7554954848 ("net: micrel: Change to receive timestamp in the frame for lan8841")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

net: phy: Micrel KSZ8061: fix errata solution not taking effect problem

[ Upstream commit 0a8d3f2e3e8d8aea8af017e14227b91d5989b696 ]

KSZ8061 needs to write to a MMD register at driver initializatio

net: phy: Micrel KSZ8061: fix errata solution not taking effect problem

[ Upstream commit 0a8d3f2e3e8d8aea8af017e14227b91d5989b696 ]

KSZ8061 needs to write to a MMD register at driver initialization to fix
an errata. This worked in 5.0 kernel but not in newer kernels. The
issue is the main phylib code no longer resets PHY at the very beginning.
Calling phy resuming code later will reset the chip if it is already
powered down at the beginning. This wipes out the MMD register write.
Solution is to implement a phy resume function for KSZ8061 to take care
of this problem.

Fixes: 232ba3a51cc2 ("net: phy: Micrel KSZ8061: link failure after cable connect")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

net: phy: micrel: fix KSZ9477 PHY issues after suspend/resume

[ Upstream commit 6149db4997f582e958da675092f21c666e3b67b7 ]

When the PHY is powered up after powered down most of the registers are
re

net: phy: micrel: fix KSZ9477 PHY issues after suspend/resume

[ Upstream commit 6149db4997f582e958da675092f21c666e3b67b7 ]

When the PHY is powered up after powered down most of the registers are
reset, so the PHY setup code needs to be done again. In addition the
interrupt register will need to be setup again so that link status
indication works again.

Fixes: 26dd2974c5b5 ("net: phy: micrel: Move KSZ9477 errata fixes to PHY driver")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

net: micrel: Fix lan8841_config_intr after getting out of sleep mode

[ Upstream commit 4fb679040d9f758eeb3b4d01bbde6405bf20e64e ]

When the interrupt is enabled, the function lan8841_config_intr tri

net: micrel: Fix lan8841_config_intr after getting out of sleep mode

[ Upstream commit 4fb679040d9f758eeb3b4d01bbde6405bf20e64e ]

When the interrupt is enabled, the function lan8841_config_intr tries to
clear any pending interrupts by reading the interrupt status, then
checks the return value for errors and then continue to enable the
interrupt. It has been seen that once the system gets out of sleep mode,
the interrupt status has the value 0x400 meaning that the PHY detected
that the link was in low power. That is correct value but the problem is
that the check is wrong. We try to check for errors but we return an
error also in this case which is not an error. Therefore fix this by
returning only when there is an error.

Fixes: a8f1a19d27ef ("net: micrel: Add support for lan8841 PHY")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Suman Ghosh <sumang@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240524085350.359812-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

net: phy: micrel: set soft_reset callback to genphy_soft_reset for KSZ8061

[ Upstream commit 128d54fbcb14b8717ecf596d3dbded327b9980b3 ]

Following a similar reinstate for the KSZ8081 and KSZ9031.

O

net: phy: micrel: set soft_reset callback to genphy_soft_reset for KSZ8061

[ Upstream commit 128d54fbcb14b8717ecf596d3dbded327b9980b3 ]

Following a similar reinstate for the KSZ8081 and KSZ9031.

Older kernels would use the genphy_soft_reset if the PHY did not implement
a .soft_reset.

The KSZ8061 errata described here:
https://ww1.microchip.com/downloads/en/DeviceDoc/KSZ8061-Errata-DS80000688B.pdf
and worked around with 232ba3a51c ("net: phy: Micrel KSZ8061: link failure after cable connect")
is back again without this soft reset.

Fixes: 6e2d85ec0559 ("net: phy: Stop with excessive soft reset")
Tested-by: Karim Ben Houcine <karim.benhoucine@landisgyr.com>
Signed-off-by: Mathieu Othacehe <othacehe@gnu.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

net: micrel: Fix receiving the timestamp in the frame for lan8841

[ Upstream commit aea27a92a41dae14843f92c79e9e42d8f570105c ]

The blamed commit started to use the ptp workqueue to get the second
p

net: micrel: Fix receiving the timestamp in the frame for lan8841

[ Upstream commit aea27a92a41dae14843f92c79e9e42d8f570105c ]

The blamed commit started to use the ptp workqueue to get the second
part of the timestamp. And when the port was set down, then this
workqueue is stopped. But if the config option NETWORK_PHY_TIMESTAMPING
is not enabled, then the ptp_clock is not initialized so then it would
crash when it would try to access the delayed work.
So then basically by setting up and then down the port, it would crash.
The fix consists in checking if the ptp_clock is initialized and only
then cancel the delayed work.

Fixes: cc7554954848 ("net: micrel: Change to receive timestamp in the frame for lan8841")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

net: micrel: Fix lan8841_config_intr after getting out of sleep mode

[ Upstream commit 4fb679040d9f758eeb3b4d01bbde6405bf20e64e ]

When the interrupt is enabled, the function lan8841_config_intr tri

net: micrel: Fix lan8841_config_intr after getting out of sleep mode

[ Upstream commit 4fb679040d9f758eeb3b4d01bbde6405bf20e64e ]

When the interrupt is enabled, the function lan8841_config_intr tries to
clear any pending interrupts by reading the interrupt status, then
checks the return value for errors and then continue to enable the
interrupt. It has been seen that once the system gets out of sleep mode,
the interrupt status has the value 0x400 meaning that the PHY detected
that the link was in low power. That is correct value but the problem is
that the check is wrong. We try to check for errors but we return an
error also in this case which is not an error. Therefore fix this by
returning only when there is an error.

Fixes: a8f1a19d27ef ("net: micrel: Add support for lan8841 PHY")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Suman Ghosh <sumang@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240524085350.359812-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

net: phy: micrel: set soft_reset callback to genphy_soft_reset for KSZ8061

[ Upstream commit 128d54fbcb14b8717ecf596d3dbded327b9980b3 ]

Following a similar reinstate for the KSZ8081 and KSZ9031.

O

net: phy: micrel: set soft_reset callback to genphy_soft_reset for KSZ8061

[ Upstream commit 128d54fbcb14b8717ecf596d3dbded327b9980b3 ]

Following a similar reinstate for the KSZ8081 and KSZ9031.

Older kernels would use the genphy_soft_reset if the PHY did not implement
a .soft_reset.

The KSZ8061 errata described here:
https://ww1.microchip.com/downloads/en/DeviceDoc/KSZ8061-Errata-DS80000688B.pdf
and worked around with 232ba3a51c ("net: phy: Micrel KSZ8061: link failure after cable connect")
is back again without this soft reset.

Fixes: 6e2d85ec0559 ("net: phy: Stop with excessive soft reset")
Tested-by: Karim Ben Houcine <karim.benhoucine@landisgyr.com>
Signed-off-by: Mathieu Othacehe <othacehe@gnu.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

net: micrel: Fix receiving the timestamp in the frame for lan8841

[ Upstream commit aea27a92a41dae14843f92c79e9e42d8f570105c ]

The blamed commit started to use the ptp workqueue to get the second
p

net: micrel: Fix receiving the timestamp in the frame for lan8841

[ Upstream commit aea27a92a41dae14843f92c79e9e42d8f570105c ]

The blamed commit started to use the ptp workqueue to get the second
part of the timestamp. And when the port was set down, then this
workqueue is stopped. But if the config option NETWORK_PHY_TIMESTAMPING
is not enabled, then the ptp_clock is not initialized so then it would
crash when it would try to access the delayed work.
So then basically by setting up and then down the port, it would crash.
The fix consists in checking if the ptp_clock is initialized and only
then cancel the delayed work.

Fixes: cc7554954848 ("net: micrel: Change to receive timestamp in the frame for lan8841")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

net: micrel: Fix lan8841_config_intr after getting out of sleep mode

[ Upstream commit 4fb679040d9f758eeb3b4d01bbde6405bf20e64e ]

When the interrupt is enabled, the function lan8841_config_intr tri

net: micrel: Fix lan8841_config_intr after getting out of sleep mode

[ Upstream commit 4fb679040d9f758eeb3b4d01bbde6405bf20e64e ]

When the interrupt is enabled, the function lan8841_config_intr tries to
clear any pending interrupts by reading the interrupt status, then
checks the return value for errors and then continue to enable the
interrupt. It has been seen that once the system gets out of sleep mode,
the interrupt status has the value 0x400 meaning that the PHY detected
that the link was in low power. That is correct value but the problem is
that the check is wrong. We try to check for errors but we return an
error also in this case which is not an error. Therefore fix this by
returning only when there is an error.

Fixes: a8f1a19d27ef ("net: micrel: Add support for lan8841 PHY")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Suman Ghosh <sumang@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240524085350.359812-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

net: phy: micrel: set soft_reset callback to genphy_soft_reset for KSZ8061

[ Upstream commit 128d54fbcb14b8717ecf596d3dbded327b9980b3 ]

Following a similar reinstate for the KSZ8081 and KSZ9031.

O

net: phy: micrel: set soft_reset callback to genphy_soft_reset for KSZ8061

[ Upstream commit 128d54fbcb14b8717ecf596d3dbded327b9980b3 ]

Following a similar reinstate for the KSZ8081 and KSZ9031.

Older kernels would use the genphy_soft_reset if the PHY did not implement
a .soft_reset.

The KSZ8061 errata described here:
https://ww1.microchip.com/downloads/en/DeviceDoc/KSZ8061-Errata-DS80000688B.pdf
and worked around with 232ba3a51c ("net: phy: Micrel KSZ8061: link failure after cable connect")
is back again without this soft reset.

Fixes: 6e2d85ec0559 ("net: phy: Stop with excessive soft reset")
Tested-by: Karim Ben Houcine <karim.benhoucine@landisgyr.com>
Signed-off-by: Mathieu Othacehe <othacehe@gnu.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

net: micrel: Fix receiving the timestamp in the frame for lan8841

[ Upstream commit aea27a92a41dae14843f92c79e9e42d8f570105c ]

The blamed commit started to use the ptp workqueue to get the second
p

net: micrel: Fix receiving the timestamp in the frame for lan8841

[ Upstream commit aea27a92a41dae14843f92c79e9e42d8f570105c ]

The blamed commit started to use the ptp workqueue to get the second
part of the timestamp. And when the port was set down, then this
workqueue is stopped. But if the config option NETWORK_PHY_TIMESTAMPING
is not enabled, then the ptp_clock is not initialized so then it would
crash when it would try to access the delayed work.
So then basically by setting up and then down the port, it would crash.
The fix consists in checking if the ptp_clock is initialized and only
then cancel the delayed work.

Fixes: cc7554954848 ("net: micrel: Change to receive timestamp in the frame for lan8841")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

net: micrel: Fix lan8841_config_intr after getting out of sleep mode

[ Upstream commit 4fb679040d9f758eeb3b4d01bbde6405bf20e64e ]

When the interrupt is enabled, the function lan8841_config_intr tri

net: micrel: Fix lan8841_config_intr after getting out of sleep mode

[ Upstream commit 4fb679040d9f758eeb3b4d01bbde6405bf20e64e ]

When the interrupt is enabled, the function lan8841_config_intr tries to
clear any pending interrupts by reading the interrupt status, then
checks the return value for errors and then continue to enable the
interrupt. It has been seen that once the system gets out of sleep mode,
the interrupt status has the value 0x400 meaning that the PHY detected
that the link was in low power. That is correct value but the problem is
that the check is wrong. We try to check for errors but we return an
error also in this case which is not an error. Therefore fix this by
returning only when there is an error.

Fixes: a8f1a19d27ef ("net: micrel: Add support for lan8841 PHY")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Suman Ghosh <sumang@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240524085350.359812-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

net: phy: micrel: set soft_reset callback to genphy_soft_reset for KSZ8061

[ Upstream commit 128d54fbcb14b8717ecf596d3dbded327b9980b3 ]

Following a similar reinstate for the KSZ8081 and KSZ9031.

O

net: phy: micrel: set soft_reset callback to genphy_soft_reset for KSZ8061

[ Upstream commit 128d54fbcb14b8717ecf596d3dbded327b9980b3 ]

Following a similar reinstate for the KSZ8081 and KSZ9031.

Older kernels would use the genphy_soft_reset if the PHY did not implement
a .soft_reset.

The KSZ8061 errata described here:
https://ww1.microchip.com/downloads/en/DeviceDoc/KSZ8061-Errata-DS80000688B.pdf
and worked around with 232ba3a51c ("net: phy: Micrel KSZ8061: link failure after cable connect")
is back again without this soft reset.

Fixes: 6e2d85ec0559 ("net: phy: Stop with excessive soft reset")
Tested-by: Karim Ben Houcine <karim.benhoucine@landisgyr.com>
Signed-off-by: Mathieu Othacehe <othacehe@gnu.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

net: micrel: Fix receiving the timestamp in the frame for lan8841

[ Upstream commit aea27a92a41dae14843f92c79e9e42d8f570105c ]

The blamed commit started to use the ptp workqueue to get the second
p

net: micrel: Fix receiving the timestamp in the frame for lan8841

[ Upstream commit aea27a92a41dae14843f92c79e9e42d8f570105c ]

The blamed commit started to use the ptp workqueue to get the second
part of the timestamp. And when the port was set down, then this
workqueue is stopped. But if the config option NETWORK_PHY_TIMESTAMPING
is not enabled, then the ptp_clock is not initialized so then it would
crash when it would try to access the delayed work.
So then basically by setting up and then down the port, it would crash.
The fix consists in checking if the ptp_clock is initialized and only
then cancel the delayed work.

Fixes: cc7554954848 ("net: micrel: Change to receive timestamp in the frame for lan8841")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

net: micrel: Fix lan8841_config_intr after getting out of sleep mode

[ Upstream commit 4fb679040d9f758eeb3b4d01bbde6405bf20e64e ]

When the interrupt is enabled, the function lan8841_config_intr tri

net: micrel: Fix lan8841_config_intr after getting out of sleep mode

[ Upstream commit 4fb679040d9f758eeb3b4d01bbde6405bf20e64e ]

When the interrupt is enabled, the function lan8841_config_intr tries to
clear any pending interrupts by reading the interrupt status, then
checks the return value for errors and then continue to enable the
interrupt. It has been seen that once the system gets out of sleep mode,
the interrupt status has the value 0x400 meaning that the PHY detected
that the link was in low power. That is correct value but the problem is
that the check is wrong. We try to check for errors but we return an
error also in this case which is not an error. Therefore fix this by
returning only when there is an error.

Fixes: a8f1a19d27ef ("net: micrel: Add support for lan8841 PHY")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Suman Ghosh <sumang@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240524085350.359812-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

net: phy: micrel: set soft_reset callback to genphy_soft_reset for KSZ8061

[ Upstream commit 128d54fbcb14b8717ecf596d3dbded327b9980b3 ]

Following a similar reinstate for the KSZ8081 and KSZ9031.

O

net: phy: micrel: set soft_reset callback to genphy_soft_reset for KSZ8061

[ Upstream commit 128d54fbcb14b8717ecf596d3dbded327b9980b3 ]

Following a similar reinstate for the KSZ8081 and KSZ9031.

Older kernels would use the genphy_soft_reset if the PHY did not implement
a .soft_reset.

The KSZ8061 errata described here:
https://ww1.microchip.com/downloads/en/DeviceDoc/KSZ8061-Errata-DS80000688B.pdf
and worked around with 232ba3a51c ("net: phy: Micrel KSZ8061: link failure after cable connect")
is back again without this soft reset.

Fixes: 6e2d85ec0559 ("net: phy: Stop with excessive soft reset")
Tested-by: Karim Ben Houcine <karim.benhoucine@landisgyr.com>
Signed-off-by: Mathieu Othacehe <othacehe@gnu.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

net: micrel: Fix receiving the timestamp in the frame for lan8841

[ Upstream commit aea27a92a41dae14843f92c79e9e42d8f570105c ]

The blamed commit started to use the ptp workqueue to get the second
p

net: micrel: Fix receiving the timestamp in the frame for lan8841

[ Upstream commit aea27a92a41dae14843f92c79e9e42d8f570105c ]

The blamed commit started to use the ptp workqueue to get the second
part of the timestamp. And when the port was set down, then this
workqueue is stopped. But if the config option NETWORK_PHY_TIMESTAMPING
is not enabled, then the ptp_clock is not initialized so then it would
crash when it would try to access the delayed work.
So then basically by setting up and then down the port, it would crash.
The fix consists in checking if the ptp_clock is initialized and only
then cancel the delayed work.

Fixes: cc7554954848 ("net: micrel: Change to receive timestamp in the frame for lan8841")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

net: micrel: Fix lan8841_config_intr after getting out of sleep mode

[ Upstream commit 4fb679040d9f758eeb3b4d01bbde6405bf20e64e ]

When the interrupt is enabled, the function lan8841_config_intr tri

net: micrel: Fix lan8841_config_intr after getting out of sleep mode

[ Upstream commit 4fb679040d9f758eeb3b4d01bbde6405bf20e64e ]

When the interrupt is enabled, the function lan8841_config_intr tries to
clear any pending interrupts by reading the interrupt status, then
checks the return value for errors and then continue to enable the
interrupt. It has been seen that once the system gets out of sleep mode,
the interrupt status has the value 0x400 meaning that the PHY detected
that the link was in low power. That is correct value but the problem is
that the check is wrong. We try to check for errors but we return an
error also in this case which is not an error. Therefore fix this by
returning only when there is an error.

Fixes: a8f1a19d27ef ("net: micrel: Add support for lan8841 PHY")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Suman Ghosh <sumang@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240524085350.359812-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

net: phy: micrel: set soft_reset callback to genphy_soft_reset for KSZ8061

[ Upstream commit 128d54fbcb14b8717ecf596d3dbded327b9980b3 ]

Following a similar reinstate for the KSZ8081 and KSZ9031.

O

net: phy: micrel: set soft_reset callback to genphy_soft_reset for KSZ8061

[ Upstream commit 128d54fbcb14b8717ecf596d3dbded327b9980b3 ]

Following a similar reinstate for the KSZ8081 and KSZ9031.

Older kernels would use the genphy_soft_reset if the PHY did not implement
a .soft_reset.

The KSZ8061 errata described here:
https://ww1.microchip.com/downloads/en/DeviceDoc/KSZ8061-Errata-DS80000688B.pdf
and worked around with 232ba3a51c ("net: phy: Micrel KSZ8061: link failure after cable connect")
is back again without this soft reset.

Fixes: 6e2d85ec0559 ("net: phy: Stop with excessive soft reset")
Tested-by: Karim Ben Houcine <karim.benhoucine@landisgyr.com>
Signed-off-by: Mathieu Othacehe <othacehe@gnu.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

net: micrel: Fix receiving the timestamp in the frame for lan8841

[ Upstream commit aea27a92a41dae14843f92c79e9e42d8f570105c ]

The blamed commit started to use the ptp workqueue to get the second
p

net: micrel: Fix receiving the timestamp in the frame for lan8841

[ Upstream commit aea27a92a41dae14843f92c79e9e42d8f570105c ]

The blamed commit started to use the ptp workqueue to get the second
part of the timestamp. And when the port was set down, then this
workqueue is stopped. But if the config option NETWORK_PHY_TIMESTAMPING
is not enabled, then the ptp_clock is not initialized so then it would
crash when it would try to access the delayed work.
So then basically by setting up and then down the port, it would crash.
The fix consists in checking if the ptp_clock is initialized and only
then cancel the delayed work.

Fixes: cc7554954848 ("net: micrel: Change to receive timestamp in the frame for lan8841")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...