ravb: Remove the macros NUM_TX_DESC_GEN[23]

For addressing 4 bytes alignment restriction on transmission
buffer for R-Car Gen2 we use 2 descriptors whereas it is a single
descriptor for other cases.

ravb: Remove the macros NUM_TX_DESC_GEN[23]

For addressing 4 bytes alignment restriction on transmission
buffer for R-Car Gen2 we use 2 descriptors whereas it is a single
descriptor for other cases.
Replace the macros NUM_TX_DESC_GEN[23] with magic number and
add a comment to explain it.

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Suggested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

ravb: Add tx_counters to struct ravb_hw_info

The register for retrieving TX counters is present only on R-Car Gen3
and RZ/G2L; it is not present on R-Car Gen2.

Add the tx_counters hw feature bit to

ravb: Add tx_counters to struct ravb_hw_info

The register for retrieving TX counters is present only on R-Car Gen3
and RZ/G2L; it is not present on R-Car Gen2.

Add the tx_counters hw feature bit to struct ravb_hw_info, to enable this
feature specifically for R-Car Gen3 now and later extend it to RZ/G2L.

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

ravb: Add internal delay hw feature to struct ravb_hw_info

R-Car Gen3 supports TX and RX clock internal delay modes, whereas R-Car
Gen2 and RZ/G2L do not support it.
Add an internal_delay hw feature

ravb: Add internal delay hw feature to struct ravb_hw_info

R-Car Gen3 supports TX and RX clock internal delay modes, whereas R-Car
Gen2 and RZ/G2L do not support it.
Add an internal_delay hw feature bit to struct ravb_hw_info to enable this
only for R-Car Gen3.

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

ravb: Add net_features and net_hw_features to struct ravb_hw_info

On R-Car the checksum calculation on RX frames is done by the E-MAC
module, whereas on RZ/G2L it is done by the TOE.

TOE calculates

ravb: Add net_features and net_hw_features to struct ravb_hw_info

On R-Car the checksum calculation on RX frames is done by the E-MAC
module, whereas on RZ/G2L it is done by the TOE.

TOE calculates the checksum of received frames from E-MAC and outputs it to
DMAC. TOE also calculates the checksum of transmission frames from DMAC and
outputs it E-MAC.

Add net_features and net_hw_features to struct ravb_hw_info, to support
subsequent SoCs without any code changes in the ravb_probe function.

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

ravb: Add gstrings_stats and gstrings_size to struct ravb_hw_info

The device stats strings for R-Car and RZ/G2L are different.

R-Car provides 30 device stats, whereas RZ/G2L provides only 15. In
ad

ravb: Add gstrings_stats and gstrings_size to struct ravb_hw_info

The device stats strings for R-Car and RZ/G2L are different.

R-Car provides 30 device stats, whereas RZ/G2L provides only 15. In
addition, RZ/G2L has stats "rx_queue_0_csum_offload_errors" instead of
"rx_queue_0_missed_errors".

Add structure variables gstrings_stats and gstrings_size to struct
ravb_hw_info, so that subsequent SoCs can be added without any code
changes in the ravb_get_strings function.

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

ravb: Add stats_len to struct ravb_hw_info

R-Car provides 30 device stats, whereas RZ/G2L provides only 15. In
addition, RZ/G2L has stats "rx_queue_0_csum_offload_errors" instead of
"rx_queue_0_miss

ravb: Add stats_len to struct ravb_hw_info

R-Car provides 30 device stats, whereas RZ/G2L provides only 15. In
addition, RZ/G2L has stats "rx_queue_0_csum_offload_errors" instead of
"rx_queue_0_missed_errors".

Replace RAVB_STATS_LEN macro with a structure variable stats_len to
struct ravb_hw_info, to support subsequent SoCs without any code changes
to the ravb_get_sset_count function.

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

ravb: Add max_rx_len to struct ravb_hw_info

The maximum descriptor size that can be specified on the reception side for
R-Car is 2048 bytes, whereas for RZ/G2L it is 8096.

Add the max_rx_len variab

ravb: Add max_rx_len to struct ravb_hw_info

The maximum descriptor size that can be specified on the reception side for
R-Car is 2048 bytes, whereas for RZ/G2L it is 8096.

Add the max_rx_len variable to struct ravb_hw_info for allocating different
RX skb buffer sizes for R-Car and RZ/G2L using the netdev_alloc_skb
function.

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

ravb: Add aligned_tx to struct ravb_hw_info

R-Car Gen2 needs a 4byte aligned address for the transmission buffer,
whereas R-Car Gen3 doesn't have any such restriction.

Add aligned_tx to struct ravb

ravb: Add aligned_tx to struct ravb_hw_info

R-Car Gen2 needs a 4byte aligned address for the transmission buffer,
whereas R-Car Gen3 doesn't have any such restriction.

Add aligned_tx to struct ravb_hw_info to select the driver to choose
between aligned and unaligned tx buffers.

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

ravb: Add struct ravb_hw_info to driver data

The DMAC and EMAC blocks of Gigabit Ethernet IP found on RZ/G2L SoC are
similar to the R-Car Ethernet AVB IP. With a few changes in the driver we
can sup

ravb: Add struct ravb_hw_info to driver data

The DMAC and EMAC blocks of Gigabit Ethernet IP found on RZ/G2L SoC are
similar to the R-Car Ethernet AVB IP. With a few changes in the driver we
can support both IPs.

This patch adds the struct ravb_hw_info to hold hw features, driver data
and function pointers to support both the IPs. It also replaces the driver
data chip type with struct ravb_hw_info by moving chip type to it.

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

ravb: Use unsigned int for num_tx_desc variable in struct ravb_private

The number of TX descriptors per packet is an unsigned value and
the variable for holding this information should be unsigned.

ravb: Use unsigned int for num_tx_desc variable in struct ravb_private

The number of TX descriptors per packet is an unsigned value and
the variable for holding this information should be unsigned.

This patch replaces the data type of num_tx_desc variable in struct
ravb_private from 'int' to 'unsigned int'.
This patch also updates the data type of local variables to unsigned int,
where the local variables are evaluated using num_tx_desc.

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

ravb: Remove checks for unsupported internal delay modes

The EtherAVB instances on the R-Car E3/D3 and RZ/G2E SoCs do not support
TX clock internal delay modes, and the EtherAVB driver prints a warn

ravb: Remove checks for unsupported internal delay modes

The EtherAVB instances on the R-Car E3/D3 and RZ/G2E SoCs do not support
TX clock internal delay modes, and the EtherAVB driver prints a warning
if an unsupported "rgmii-*id" PHY mode is specified, to catch buggy
DTBs.

Commit a6f51f2efa742df0 ("ravb: Add support for explicit internal
clock delay configuration") deprecated deriving the internal delay mode
from the PHY mode, in favor of explicit configuration using the now
mandatory "rx-internal-delay-ps" and "tx-internal-delay-ps" properties,
thus delegating the warning to the legacy fallback code.

Since explicit configuration of a (valid) internal clock delay
configuration is enforced by validating device tree source files against
DT binding files, and all upstream DTS files have been converted as of
commit a5200e63af57d05e ("arm64: dts: renesas: rzg2: Convert EtherAVB to
explicit delay handling"), the checks in the legacy fallback code can be
removed.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/2037542ac56e99413b9807e24049711553cc88a9.1628696778.git.geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

dev_ioctl: split out ndo_eth_ioctl

Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SI

dev_ioctl: split out ndo_eth_ioctl

Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.

Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.

This is a purely cosmetic change intended to help readers find
their way through the implementation.

Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

ravb: Fix a typo in comment

Fix the typo RX->TX in comment, as the code following the comment
process TX and not RX.

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar

ravb: Fix a typo in comment

Fix the typo RX->TX in comment, as the code following the comment
process TX and not RX.

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: ethernet: ravb: Use devm_platform_get_and_ioremap_resource()

Use devm_platform_get_and_ioremap_resource() to simplify
code.

Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by

net: ethernet: ravb: Use devm_platform_get_and_ioremap_resource()

Use devm_platform_get_and_ioremap_resource() to simplify
code.

Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: ethernet: ravb: Fix release of refclk

The call to clk_disable_unprepare() can happen before priv is
initialized. This means moving clk_disable_unprepare out of
out_release into a new label.

Fi

net: ethernet: ravb: Fix release of refclk

The call to clk_disable_unprepare() can happen before priv is
initialized. This means moving clk_disable_unprepare out of
out_release into a new label.

Fixes: 8ef7adc6beb2 ("net: ethernet: ravb: Enable optional refclk")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: renesas: ravb: Fix a stuck issue when a lot of frames are received

When a lot of frames were received in the short term, the driver
caused a stuck of receiving until a new frame was received. F

net: renesas: ravb: Fix a stuck issue when a lot of frames are received

When a lot of frames were received in the short term, the driver
caused a stuck of receiving until a new frame was received. For example,
the following command from other device could cause this issue.

$ sudo ping -f -l 1000 -c 1000 <this driver's ipaddress>

The previous code always cleared the interrupt flag of RX but checks
the interrupt flags in ravb_poll(). So, ravb_poll() could not call
ravb_rx() in the next time until a new RX frame was received if
ravb_rx() returned true. To fix the issue, always calls ravb_rx()
regardless the interrupt flags condition.

Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

of: net: pass the dst buffer to of_get_mac_address()

of_get_mac_address() returns a "const void*" pointer to a MAC address.
Lately, support to fetch the MAC address by an NVMEM provider was added.
B

of: net: pass the dst buffer to of_get_mac_address()

of_get_mac_address() returns a "const void*" pointer to a MAC address.
Lately, support to fetch the MAC address by an NVMEM provider was added.
But this will only work with platform devices. It will not work with
PCI devices (e.g. of an integrated root complex) and esp. not with DSA
ports.

There is an of_* variant of the nvmem binding which works without
devices. The returned data of a nvmem_cell_read() has to be freed after
use. On the other hand the return of_get_mac_address() points to some
static data without a lifetime. The trick for now, was to allocate a
device resource managed buffer which is then returned. This will only
work if we have an actual device.

Change it, so that the caller of of_get_mac_address() has to supply a
buffer where the MAC address is written to. Unfortunately, this will
touch all drivers which use the of_get_mac_address().

Usually the code looks like:

const char *addr;
addr = of_get_mac_address(np);
if (!IS_ERR(addr))
ether_addr_copy(ndev->dev_addr, addr);

This can then be simply rewritten as:

of_get_mac_address(np, ndev->dev_addr);

Sometimes is_valid_ether_addr() is used to test the MAC address.
of_get_mac_address() already makes sure, it just returns a valid MAC
address. Thus we can just test its return code. But we have to be
careful if there are still other sources for the MAC address before the
of_get_mac_address(). In this case we have to keep the
is_valid_ether_addr() call.

The following coccinelle patch was used to convert common cases to the
new style. Afterwards, I've manually gone over the drivers and fixed the
return code variable: either used a new one or if one was already
available use that. Mansour Moufid, thanks for that coccinelle patch!

<spml>
@a@
identifier x;
expression y, z;
@@
- x = of_get_mac_address(y);
+ x = of_get_mac_address(y, z);
<...
- ether_addr_copy(z, x);
...>

@@
identifier a.x;
@@
- if (<+... x ...+>) {}

@@
identifier a.x;
@@
if (<+... x ...+>) {
...
}
- else {}

@@
identifier a.x;
expression e;
@@
- if (<+... x ...+>@e)
- {}
- else
+ if (!(e))
{...}

@@
expression x, y, z;
@@
- x = of_get_mac_address(y, z);
+ of_get_mac_address(y, z);
... when != x
</spml>

All drivers, except drivers/net/ethernet/aeroflex/greth.c, were
compile-time tested.

Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: ethernet: ravb: Enable optional refclk

For devices that use a programmable clock for the AVB reference clock,
the driver may need to enable them. Add code to find the optional clock
and enable

net: ethernet: ravb: Enable optional refclk

For devices that use a programmable clock for the AVB reference clock,
the driver may need to enable them. Add code to find the optional clock
and enable it when available.

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

ravb: remove APSR_DM

According to the R-Car Series, 3rd Generation User's Manual: Hardware,
Rev. 1.50, there's no APSR.DM field, instead there are 2 independent
RX/TX clock internal delay bits. Foll

ravb: remove APSR_DM

According to the R-Car Series, 3rd Generation User's Manual: Hardware,
Rev. 1.50, there's no APSR.DM field, instead there are 2 independent
RX/TX clock internal delay bits. Follow the suit: remove #define APSR_DM
and rename #define's APSR_DM_{R|T}DM to APSR_{R|T}DM.

While at it, do several more things to the declaration of *enum* APSR_BIT:
- remove superfluous indentation;
- annotate APSR_MEMS as undocumented;
- annotate APSR as R-Car Gen3 only.

Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

net: renesas: ravb: Fix a stuck issue when a lot of frames are received

[ Upstream commit 5718458b092bf6bf4482c5df32affba3c3259517 ]

When a lot of frames were received in the short term, the driver

net: renesas: ravb: Fix a stuck issue when a lot of frames are received

[ Upstream commit 5718458b092bf6bf4482c5df32affba3c3259517 ]

When a lot of frames were received in the short term, the driver
caused a stuck of receiving until a new frame was received. For example,
the following command from other device could cause this issue.

$ sudo ping -f -l 1000 -c 1000 <this driver's ipaddress>

The previous code always cleared the interrupt flag of RX but checks
the interrupt flags in ravb_poll(). So, ravb_poll() could not call
ravb_rx() in the next time until a new RX frame was received if
ravb_rx() returned true. To fix the issue, always calls ravb_rx()
regardless the interrupt flags condition.

Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

ravb: Fix bit fields checking in ravb_hwtstamp_get()

In the function ravb_hwtstamp_get() in ravb_main.c with the existing
values for RAVB_RXTSTAMP_TYPE_V2_L2_EVENT (0x2) and RAVB_RXTSTAMP_TYPE_ALL
(

ravb: Fix bit fields checking in ravb_hwtstamp_get()

In the function ravb_hwtstamp_get() in ravb_main.c with the existing
values for RAVB_RXTSTAMP_TYPE_V2_L2_EVENT (0x2) and RAVB_RXTSTAMP_TYPE_ALL
(0x6)

if (priv->tstamp_rx_ctrl & RAVB_RXTSTAMP_TYPE_V2_L2_EVENT)
config.rx_filter = HWTSTAMP_FILTER_PTP_V2_L2_EVENT;
else if (priv->tstamp_rx_ctrl & RAVB_RXTSTAMP_TYPE_ALL)
config.rx_filter = HWTSTAMP_FILTER_ALL;

if the test on RAVB_RXTSTAMP_TYPE_ALL should be true,
it will never be reached.

This issue can be verified with 'hwtstamp_config' testing program
(tools/testing/selftests/net/hwtstamp_config.c). Setting filter type
to ALL and subsequent retrieving it gives incorrect value:

$ hwtstamp_config eth0 OFF ALL
flags = 0
tx_type = OFF
rx_filter = ALL
$ hwtstamp_config eth0
flags = 0
tx_type = OFF
rx_filter = PTP_V2_L2_EVENT

Correct this by converting if-else's to switch.

Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper")
Reported-by: Julia Lawall <julia.lawall@inria.fr>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Link: https://lore.kernel.org/r/20201026102130.29368-1-andrew_gabbasov@mentor.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

ravb: Add support for explicit internal clock delay configuration

Some EtherAVB variants support internal clock delay configuration, which
can add larger delays than the delays that are typically su

ravb: Add support for explicit internal clock delay configuration

Some EtherAVB variants support internal clock delay configuration, which
can add larger delays than the delays that are typically supported by
the PHY (using an "rgmii-*id" PHY mode, and/or "[rt]xc-skew-ps"
properties).

Historically, the EtherAVB driver configured these delays based on the
"rgmii-*id" PHY mode. This caused issues with PHY drivers that
implement PHY internal delays properly[1]. Hence a backwards-compatible
workaround was added by masking the PHY mode[2].

Add proper support for explicit configuration of the MAC internal clock
delays using the new "[rt]x-internal-delay-ps" properties.
Fall back to the old handling if none of these properties is present.

[1] Commit bcf3440c6dd78bfe ("net: phy: micrel: add phy-mode support for
the KSZ9031 PHY")
[2] Commit 9b23203c32ee02cd ("ravb: Mask PHY mode to avoid inserting
delays twice").

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

ravb: Split delay handling in parsing and applying

Currently, full delay handling is done in both the probe and resume
paths. Split it in two parts, so the resume path doesn't have to redo
the pars

ravb: Split delay handling in parsing and applying

Currently, full delay handling is done in both the probe and resume
paths. Split it in two parts, so the resume path doesn't have to redo
the parsing part over and over again.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

Revert "ravb: Fixed to be able to unload modules"

This reverts commit 1838d6c62f57836639bd3d83e7855e0ee4f6defc.

This commit moved the ravb_mdio_init() call (and thus the
of_mdiobus_register() call)

Revert "ravb: Fixed to be able to unload modules"

This reverts commit 1838d6c62f57836639bd3d83e7855e0ee4f6defc.

This commit moved the ravb_mdio_init() call (and thus the
of_mdiobus_register() call) from the ravb_probe() to the ravb_open()
call. This causes a regression during system resume (s2idle/s2ram), as
new PHY devices cannot be bound while suspended.

During boot, the Micrel PHY is detected like this:

Micrel KSZ9031 Gigabit PHY e6800000.ethernet-ffffffff:00: attached PHY driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=e6800000.ethernet-ffffffff:00, irq=228)
ravb e6800000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off

During system suspend, (A) defer_all_probes is set to true, and (B)
usermodehelper_disabled is set to UMH_DISABLED, to avoid drivers being
probed while suspended.

A. If CONFIG_MODULES=n, phy_device_register() calling device_add()
merely adds the device, but does not probe it yet, as
really_probe() returns early due to defer_all_probes being set:

dpm_resume+0x128/0x4f8
device_resume+0xcc/0x1b0
dpm_run_callback+0x74/0x340
ravb_resume+0x190/0x1b8
ravb_open+0x84/0x770
of_mdiobus_register+0x1e0/0x468
of_mdiobus_register_phy+0x1b8/0x250
of_mdiobus_phy_device_register+0x178/0x1e8
phy_device_register+0x114/0x1b8
device_add+0x3d4/0x798
bus_probe_device+0x98/0xa0
device_initial_probe+0x10/0x18
__device_attach+0xe4/0x140
bus_for_each_drv+0x64/0xc8
__device_attach_driver+0xb8/0xe0
driver_probe_device.part.11+0xc4/0xd8
really_probe+0x32c/0x3b8

Later, phy_attach_direct() notices no PHY driver has been bound,
and falls back to the Generic PHY, leading to degraded operation:

Generic PHY e6800000.ethernet-ffffffff:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e6800000.ethernet-ffffffff:00, irq=POLL)
ravb e6800000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off

B. If CONFIG_MODULES=y, request_module() returns early with -EBUSY due
to UMH_DISABLED, and MDIO initialization fails completely:

mdio_bus e6800000.ethernet-ffffffff:00: error -16 loading PHY driver module for ID 0x00221622
ravb e6800000.ethernet eth0: failed to initialize MDIO
PM: dpm_run_callback(): ravb_resume+0x0/0x1b8 returns -16
PM: Device e6800000.ethernet failed to resume: error -16

Ignoring -EBUSY in phy_request_driver_module(), like was done for
-ENOENT in commit 21e194425abd65b5 ("net: phy: fix issue with loading
PHY driver w/o initramfs"), would makes it fall back to the Generic
PHY, like in the CONFIG_MODULES=n case.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable@vger.kernel.org
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: ethernet: ravb: constify bb_ops

The only usage of bb_ops is to assign its address to the ops field in
the mdiobb_ctrl struct, which is a const pointer. Make it const to allow
the compiler to pu

net: ethernet: ravb: constify bb_ops

The only usage of bb_ops is to assign its address to the ops field in
the mdiobb_ctrl struct, which is a const pointer. Make it const to allow
the compiler to put it in read-only memory.

Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...