bnx2x: new flag for track HW resource allocation

While injecting PCIe errors to the upstream PCIe switch of
a BCM57810 NIC, system hangs/crashes were observed.

After several calls to bnx2x_tx_timou

bnx2x: new flag for track HW resource allocation

While injecting PCIe errors to the upstream PCIe switch of
a BCM57810 NIC, system hangs/crashes were observed.

After several calls to bnx2x_tx_timout() complete,
bnx2x_nic_unload() is called to free up HW resources
and bnx2x_napi_disable() is called to release NAPI objects.
Later, when the EEH driver calls bnx2x_io_slot_reset() to
complete the recovery process, bnx2x attempts to disable
NAPI again by calling bnx2x_napi_disable() and freeing
resources which have already been freed, resulting in a
hang or crash.

Introduce a new flag to track the HW resource and NAPI
allocation state, refactor duplicated code into a single
function, check page pool allocation status before freeing,
and reduces debug output when a TX timeout event occurs.

Reviewed-by: Manish Chopra <manishc@marvell.com>
Tested-by: Abdul Haleem <abdhalee@in.ibm.com>
Tested-by: David Christensen <drc@linux.vnet.ibm.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Venkata Sai Duggi <venkata.sai.duggi@ibm.com>
Signed-off-by: Thinh Tran <thinhtr@linux.vnet.ibm.com>
Link: https://lore.kernel.org/r/20230818161443.708785-2-thinhtr@linux.vnet.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

bnx2x: fix page fault following EEH recovery

In the last step of the EEH recovery process, the EEH driver calls into
bnx2x_io_resume() to re-initialize the NIC hardware via the function
bnx2x_nic_lo

bnx2x: fix page fault following EEH recovery

In the last step of the EEH recovery process, the EEH driver calls into
bnx2x_io_resume() to re-initialize the NIC hardware via the function
bnx2x_nic_load(). If an error occurs during bnx2x_nic_load(), OS and
hardware resources are released and an error code is returned to the
caller. When called from bnx2x_io_resume(), the return code is ignored
and the network interface is brought up unconditionally. Later attempts
to send a packet via this interface result in a page fault due to a null
pointer reference.

This patch checks the return code of bnx2x_nic_load(), prints an error
message if necessary, and does not enable the interface.

Signed-off-by: David Christensen <drc@linux.vnet.ibm.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

Change DEFINE_SEMAPHORE() to take a number argument

Fundamentally semaphores are a counted primitive, but
DEFINE_SEMAPHORE() does not expose this and explicitly creates a
binary semaphore.

Change D

Change DEFINE_SEMAPHORE() to take a number argument

Fundamentally semaphores are a counted primitive, but
DEFINE_SEMAPHORE() does not expose this and explicitly creates a
binary semaphore.

Change DEFINE_SEMAPHORE() to take a number argument and use that in the
few places that open-coded it using __SEMAPHORE_INITIALIZER().

Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
[mcgrof: add some tribal knowledge about why some folks prefer
binary sempahores over mutexes]
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Davidlohr Bueso <dave@stgolabs.net>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>

show more ...

bnx2x: Drop redundant pci_enable_pcie_error_reporting()

pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since f26e58bf6f54 ("PCI/AER: Enable error reporting when AER is

bnx2x: Drop redundant pci_enable_pcie_error_reporting()

pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since f26e58bf6f54 ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration, so the
driver doesn't need to do it itself.

Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.

Note that this only controls ERR_* Messages from the device. An ERR_*
Message may cause the Root Port to generate an interrupt, depending on the
AER Root Error Command register managed by the AER service driver.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ariel Elior <aelior@marvell.com>
Cc: Sudarsana Kalluru <skalluru@marvell.com>
Cc: Manish Chopra <manishc@marvell.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

ptp: convert remaining drivers to adjfine interface

Convert all remaining drivers that still use .adjfreq to the newer .adjfine
implementation. These drivers are not straightforward, as they use
non

ptp: convert remaining drivers to adjfine interface

Convert all remaining drivers that still use .adjfreq to the newer .adjfine
implementation. These drivers are not straightforward, as they use
non-standard methods of programming their hardware. They are all converted
to use scaled_ppm_to_ppb to get the parts per billion value that their
logic depends on.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Ariel Elior <aelior@marvell.com>
Cc: Sudarsana Kalluru <skalluru@marvell.com>
Cc: Manish Chopra <manishc@marvell.com>
Cc: Derek Chickles <dchickles@marvell.com>
Cc: Satanand Burla <sburla@marvell.com>
Cc: Felix Manlunas <fmanlunas@marvell.com>
Cc: Raju Rangoju <rajur@chelsio.com>
Cc: Joakim Zhang <qiangqing.zhang@nxp.com>
Cc: Edward Cree <ecree.xilinx@gmail.com>
Cc: Martin Habets <habetsm.xilinx@gmail.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: ethernet: move from strlcpy with unused retval to strscpy

Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Gen

net: ethernet: move from strlcpy with unused retval to strscpy

Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.

Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # For drivers/net/ethernet/mellanox/mlxsw
Acked-by: Geoff Levand <geoff@infradead.org> # For ps3_gelic_net and spider_net_ethtool
Acked-by: Tom Lendacky <thomas.lendacky@amd.com> # For drivers/net/ethernet/amd/xgbe/xgbe-ethtool.c
Acked-by: Marcin Wojtas <mw@semihalf.com> # For drivers/net/ethernet/marvell/mvpp2
Reviewed-by: Leon Romanovsky <leonro@nvidia.com> # For drivers/net/ethernet/mellanox/mlx{4|5}
Reviewed-by: Shay Agroskin <shayagr@amazon.com> # For drivers/net/ethernet/amazon/ena
Acked-by: Krzysztof Hałasa <khalasa@piap.pl> # For IXP4xx Ethernet
Link: https://lore.kernel.org/r/20220830201457.7984-3-wsa+renesas@sang-engineering.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

bnx2x: fix napi API usage sequence

While handling PCI errors (AER flow) driver tries to
disable NAPI [napi_disable()] after NAPI is deleted
[__netif_napi_del()] which causes unexpected system
hang/c

bnx2x: fix napi API usage sequence

While handling PCI errors (AER flow) driver tries to
disable NAPI [napi_disable()] after NAPI is deleted
[__netif_napi_del()] which causes unexpected system
hang/crash.

System message log shows the following:
=======================================
[ 3222.537510] EEH: Detected PCI bus error on PHB#384-PE#800000 [ 3222.537511] EEH: This PCI device has failed 2 times in the last hour and will be permanently disabled after 5 failures.
[ 3222.537512] EEH: Notify device drivers to shutdown [ 3222.537513] EEH: Beginning: 'error_detected(IO frozen)'
[ 3222.537514] EEH: PE#800000 (PCI 0384:80:00.0): Invoking
bnx2x->error_detected(IO frozen)
[ 3222.537516] bnx2x: [bnx2x_io_error_detected:14236(eth14)]IO error detected [ 3222.537650] EEH: PE#800000 (PCI 0384:80:00.0): bnx2x driver reports:
'need reset'
[ 3222.537651] EEH: PE#800000 (PCI 0384:80:00.1): Invoking
bnx2x->error_detected(IO frozen)
[ 3222.537651] bnx2x: [bnx2x_io_error_detected:14236(eth13)]IO error detected [ 3222.537729] EEH: PE#800000 (PCI 0384:80:00.1): bnx2x driver reports:
'need reset'
[ 3222.537729] EEH: Finished:'error_detected(IO frozen)' with aggregate recovery state:'need reset'
[ 3222.537890] EEH: Collect temporary log [ 3222.583481] EEH: of node=0384:80:00.0 [ 3222.583519] EEH: PCI device/vendor: 168e14e4 [ 3222.583557] EEH: PCI cmd/status register: 00100140 [ 3222.583557] EEH: PCI-E capabilities and status follow:
[ 3222.583744] EEH: PCI-E 00: 00020010 012c8da2 00095d5e 00455c82 [ 3222.583892] EEH: PCI-E 10: 10820000 00000000 00000000 00000000 [ 3222.583893] EEH: PCI-E 20: 00000000 [ 3222.583893] EEH: PCI-E AER capability register set follows:
[ 3222.584079] EEH: PCI-E AER 00: 13c10001 00000000 00000000 00062030 [ 3222.584230] EEH: PCI-E AER 10: 00002000 000031c0 000001e0 00000000 [ 3222.584378] EEH: PCI-E AER 20: 00000000 00000000 00000000 00000000 [ 3222.584416] EEH: PCI-E AER 30: 00000000 00000000 [ 3222.584416] EEH: of node=0384:80:00.1 [ 3222.584454] EEH: PCI device/vendor: 168e14e4 [ 3222.584491] EEH: PCI cmd/status register: 00100140 [ 3222.584492] EEH: PCI-E capabilities and status follow:
[ 3222.584677] EEH: PCI-E 00: 00020010 012c8da2 00095d5e 00455c82 [ 3222.584825] EEH: PCI-E 10: 10820000 00000000 00000000 00000000 [ 3222.584826] EEH: PCI-E 20: 00000000 [ 3222.584826] EEH: PCI-E AER capability register set follows:
[ 3222.585011] EEH: PCI-E AER 00: 13c10001 00000000 00000000 00062030 [ 3222.585160] EEH: PCI-E AER 10: 00002000 000031c0 000001e0 00000000 [ 3222.585309] EEH: PCI-E AER 20: 00000000 00000000 00000000 00000000 [ 3222.585347] EEH: PCI-E AER 30: 00000000 00000000 [ 3222.586872] RTAS: event: 5, Type: Platform Error (224), Severity: 2 [ 3222.586873] EEH: Reset without hotplug activity [ 3224.762767] EEH: Beginning: 'slot_reset'
[ 3224.762770] EEH: PE#800000 (PCI 0384:80:00.0): Invoking
bnx2x->slot_reset()
[ 3224.762771] bnx2x: [bnx2x_io_slot_reset:14271(eth14)]IO slot reset initializing...
[ 3224.762887] bnx2x 0384:80:00.0: enabling device (0140 -> 0142) [ 3224.768157] bnx2x: [bnx2x_io_slot_reset:14287(eth14)]IO slot reset
--> driver unload

Uninterruptible tasks
=====================
crash> ps | grep UN
213 2 11 c000000004c89e00 UN 0.0 0 0 [eehd]
215 2 0 c000000004c80000 UN 0.0 0 0
[kworker/0:2]
2196 1 28 c000000004504f00 UN 0.1 15936 11136 wickedd
4287 1 9 c00000020d076800 UN 0.0 4032 3008 agetty
4289 1 20 c00000020d056680 UN 0.0 7232 3840 agetty
32423 2 26 c00000020038c580 UN 0.0 0 0
[kworker/26:3]
32871 4241 27 c0000002609ddd00 UN 0.1 18624 11648 sshd
32920 10130 16 c00000027284a100 UN 0.1 48512 12608 sendmail
33092 32987 0 c000000205218b00 UN 0.1 48512 12608 sendmail
33154 4567 16 c000000260e51780 UN 0.1 48832 12864 pickup
33209 4241 36 c000000270cb6500 UN 0.1 18624 11712 sshd
33473 33283 0 c000000205211480 UN 0.1 48512 12672 sendmail
33531 4241 37 c00000023c902780 UN 0.1 18624 11648 sshd

EEH handler hung while bnx2x sleeping and holding RTNL lock
===========================================================
crash> bt 213
PID: 213 TASK: c000000004c89e00 CPU: 11 COMMAND: "eehd"
#0 [c000000004d477e0] __schedule at c000000000c70808
#1 [c000000004d478b0] schedule at c000000000c70ee0
#2 [c000000004d478e0] schedule_timeout at c000000000c76dec
#3 [c000000004d479c0] msleep at c0000000002120cc
#4 [c000000004d479f0] napi_disable at c000000000a06448
^^^^^^^^^^^^^^^^
#5 [c000000004d47a30] bnx2x_netif_stop at c0080000018dba94 [bnx2x]
#6 [c000000004d47a60] bnx2x_io_slot_reset at c0080000018a551c [bnx2x]
#7 [c000000004d47b20] eeh_report_reset at c00000000004c9bc
#8 [c000000004d47b90] eeh_pe_report at c00000000004d1a8
#9 [c000000004d47c40] eeh_handle_normal_event at c00000000004da64

And the sleeping source code
============================
crash> dis -ls c000000000a06448
FILE: ../net/core/dev.c
LINE: 6702

6697 {
6698 might_sleep();
6699 set_bit(NAPI_STATE_DISABLE, &n->state);
6700
6701 while (test_and_set_bit(NAPI_STATE_SCHED, &n->state))
* 6702 msleep(1);
6703 while (test_and_set_bit(NAPI_STATE_NPSVC, &n->state))
6704 msleep(1);
6705
6706 hrtimer_cancel(&n->timer);
6707
6708 clear_bit(NAPI_STATE_DISABLE, &n->state);
6709 }

EEH calls into bnx2x twice based on the system log above, first through
bnx2x_io_error_detected() and then bnx2x_io_slot_reset(), and executes
the following call chains:

bnx2x_io_error_detected()
+-> bnx2x_eeh_nic_unload()
+-> bnx2x_del_all_napi()
+-> __netif_napi_del()

bnx2x_io_slot_reset()
+-> bnx2x_netif_stop()
+-> bnx2x_napi_disable()
+->napi_disable()

Fix this by correcting the sequence of NAPI APIs usage,
that is delete the NAPI after disabling it.

Fixes: 7fa6f34081f1 ("bnx2x: AER revised")
Reported-by: David Christensen <drc@linux.vnet.ibm.com>
Tested-by: David Christensen <drc@linux.vnet.ibm.com>
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Link: https://lore.kernel.org/r/20220426153913.6966-1-manishc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

bnx2x: fix built-in kernel driver load failure

Commit b7a49f73059f ("bnx2x: Utilize firmware 7.13.21.0")
added request_firmware() logic in probe() which caused
load failure when firmware file is not

bnx2x: fix built-in kernel driver load failure

Commit b7a49f73059f ("bnx2x: Utilize firmware 7.13.21.0")
added request_firmware() logic in probe() which caused
load failure when firmware file is not present in initrd (below),
as access to firmware file is not feasible during probe.

Direct firmware load for bnx2x/bnx2x-e2-7.13.15.0.fw failed with error -2
Direct firmware load for bnx2x/bnx2x-e2-7.13.21.0.fw failed with error -2

This patch fixes this issue by -

1. Removing request_firmware() logic from the probe()
such that .ndo_open() handle it as it used to handle
it earlier

2. Given request_firmware() is removed from probe(), so
driver has to relax FW version comparisons a bit against
the already loaded FW version (by some other PFs of same
adapter) to allow different compatible/close enough FWs with which
multiple PFs may run with (in different environments), as the
given PF who is in probe flow has no idea now with which firmware
file version it is going to initialize the device in ndo_open()

Link: https://lore.kernel.org/all/46f2d9d9-ae7f-b332-ddeb-b59802be2bab@molgen.mpg.de/
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Fixes: b7a49f73059f ("bnx2x: Utilize firmware 7.13.21.0")
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Link: https://lore.kernel.org/r/20220316214613.6884-1-manishc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

bnx2x: fix driver load from initrd

Commit b7a49f73059f ("bnx2x: Utilize firmware 7.13.21.0") added
new firmware support in the driver with maintaining older firmware
compatibility. However, older fi

bnx2x: fix driver load from initrd

Commit b7a49f73059f ("bnx2x: Utilize firmware 7.13.21.0") added
new firmware support in the driver with maintaining older firmware
compatibility. However, older firmware was not added in MODULE_FIRMWARE()
which caused missing firmware files in initrd image leading to driver load
failure from initrd. This patch adds MODULE_FIRMWARE() for older firmware
version to have firmware files included in initrd.

Fixes: b7a49f73059f ("bnx2x: Utilize firmware 7.13.21.0")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215627
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Link: https://lore.kernel.org/r/20220223085720.12021-1-manishc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

bnx2x: Remove useless DMA-32 fallback configuration

As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for

bnx2x: Remove useless DMA-32 fallback configuration

As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.

Moreover, dma_set_mask_and_coherent() returns 0 or -EIO, so the return
code of the function can be used directly.

Finally, inline bnx2x_set_coherency_mask() because it is now only a wrapper
for a single dma_set_mask_and_coherent() call.

Simplify code and remove some dead code accordingly.

[1]: https://lkml.org/lkml/2021/6/7/398

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/29608a525876afddceabf8f11b2ba606da8748fc.1641730747.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

bnx2x: Utilize firmware 7.13.21.0

This new firmware addresses few important issues and enhancements
as mentioned below -

- Support direct invalidation of FP HSI Ver per function ID, required for

bnx2x: Utilize firmware 7.13.21.0

This new firmware addresses few important issues and enhancements
as mentioned below -

- Support direct invalidation of FP HSI Ver per function ID, required for
invalidating FP HSI Ver prior to each VF start, as there is no VF start
- BRB hardware block parity error detection support for the driver
- Fix the FCOE underrun flow
- Fix PSOD during FCoE BFS over the NIC ports after preboot driver
- Maintains backward compatibility

This patch incorporates this new firmware 7.13.21.0 in bnx2x driver.

Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net_tstamp: add new flag HWTSTAMP_FLAG_BONDED_PHC_INDEX

Since commit 94dd016ae538 ("bond: pass get_ts_info and SIOC[SG]HWTSTAMP
ioctl to active device") the user could get bond active interface's
PH

net_tstamp: add new flag HWTSTAMP_FLAG_BONDED_PHC_INDEX

Since commit 94dd016ae538 ("bond: pass get_ts_info and SIOC[SG]HWTSTAMP
ioctl to active device") the user could get bond active interface's
PHC index directly. But when there is a failover, the bond active
interface will change, thus the PHC index is also changed. This may
break the user's program if they did not update the PHC timely.

This patch adds a new hwtstamp_config flag HWTSTAMP_FLAG_BONDED_PHC_INDEX.
When the user wants to get the bond active interface's PHC, they need to
add this flag and be aware the PHC index may be changed.

With the new flag. All flag checks in current drivers are removed. Only
the checking in net_hwtstamp_validate() is kept.

Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

ethernet: bnx2x: use eth_hw_addr_set()

Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->de

ethernet: bnx2x: use eth_hw_addr_set()

Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.

Read the address into an array on the stack, then call
eth_hw_addr_set().

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

ethernet: constify references to netdev->dev_addr in drivers

This big patch sprinkles const on local variables and
function arguments which may refer to netdev->dev_addr.

Commit 406f42fa0d3c ("net-

ethernet: constify references to netdev->dev_addr in drivers

This big patch sprinkles const on local variables and
function arguments which may refer to netdev->dev_addr.

Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.

Some of the changes here are not strictly required - const
is sometimes cast off but pointer is not used for writing.
It seems like it's still better to add the const in case
the code changes later or relevant -W flags get enabled
for the build.

No functional changes.

Link: https://lore.kernel.org/r/20211014142432.449314-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

ethernet: use eth_hw_addr_set()

Convert all Ethernet drivers from memcpy(... ETH_ADDR)
to eth_hw_addr_set():

@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, ETH_ALEN)
+ eth_hw_addr_

ethernet: use eth_hw_addr_set()

Convert all Ethernet drivers from memcpy(... ETH_ADDR)
to eth_hw_addr_set():

@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, ETH_ALEN)
+ eth_hw_addr_set(dev, np)

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

bnx2x: fix napi API usage sequence

[ Upstream commit af68656d66eda219b7f55ce8313a1da0312c79e1 ]

While handling PCI errors (AER flow) driver tries to
disable NAPI [napi_disable()] after NAPI is dele

bnx2x: fix napi API usage sequence

[ Upstream commit af68656d66eda219b7f55ce8313a1da0312c79e1 ]

While handling PCI errors (AER flow) driver tries to
disable NAPI [napi_disable()] after NAPI is deleted
[__netif_napi_del()] which causes unexpected system
hang/crash.

System message log shows the following:
=======================================
[ 3222.537510] EEH: Detected PCI bus error on PHB#384-PE#800000 [ 3222.537511] EEH: This PCI device has failed 2 times in the last hour and will be permanently disabled after 5 failures.
[ 3222.537512] EEH: Notify device drivers to shutdown [ 3222.537513] EEH: Beginning: 'error_detected(IO frozen)'
[ 3222.537514] EEH: PE#800000 (PCI 0384:80:00.0): Invoking
bnx2x->error_detected(IO frozen)
[ 3222.537516] bnx2x: [bnx2x_io_error_detected:14236(eth14)]IO error detected [ 3222.537650] EEH: PE#800000 (PCI 0384:80:00.0): bnx2x driver reports:
'need reset'
[ 3222.537651] EEH: PE#800000 (PCI 0384:80:00.1): Invoking
bnx2x->error_detected(IO frozen)
[ 3222.537651] bnx2x: [bnx2x_io_error_detected:14236(eth13)]IO error detected [ 3222.537729] EEH: PE#800000 (PCI 0384:80:00.1): bnx2x driver reports:
'need reset'
[ 3222.537729] EEH: Finished:'error_detected(IO frozen)' with aggregate recovery state:'need reset'
[ 3222.537890] EEH: Collect temporary log [ 3222.583481] EEH: of node=0384:80:00.0 [ 3222.583519] EEH: PCI device/vendor: 168e14e4 [ 3222.583557] EEH: PCI cmd/status register: 00100140 [ 3222.583557] EEH: PCI-E capabilities and status follow:
[ 3222.583744] EEH: PCI-E 00: 00020010 012c8da2 00095d5e 00455c82 [ 3222.583892] EEH: PCI-E 10: 10820000 00000000 00000000 00000000 [ 3222.583893] EEH: PCI-E 20: 00000000 [ 3222.583893] EEH: PCI-E AER capability register set follows:
[ 3222.584079] EEH: PCI-E AER 00: 13c10001 00000000 00000000 00062030 [ 3222.584230] EEH: PCI-E AER 10: 00002000 000031c0 000001e0 00000000 [ 3222.584378] EEH: PCI-E AER 20: 00000000 00000000 00000000 00000000 [ 3222.584416] EEH: PCI-E AER 30: 00000000 00000000 [ 3222.584416] EEH: of node=0384:80:00.1 [ 3222.584454] EEH: PCI device/vendor: 168e14e4 [ 3222.584491] EEH: PCI cmd/status register: 00100140 [ 3222.584492] EEH: PCI-E capabilities and status follow:
[ 3222.584677] EEH: PCI-E 00: 00020010 012c8da2 00095d5e 00455c82 [ 3222.584825] EEH: PCI-E 10: 10820000 00000000 00000000 00000000 [ 3222.584826] EEH: PCI-E 20: 00000000 [ 3222.584826] EEH: PCI-E AER capability register set follows:
[ 3222.585011] EEH: PCI-E AER 00: 13c10001 00000000 00000000 00062030 [ 3222.585160] EEH: PCI-E AER 10: 00002000 000031c0 000001e0 00000000 [ 3222.585309] EEH: PCI-E AER 20: 00000000 00000000 00000000 00000000 [ 3222.585347] EEH: PCI-E AER 30: 00000000 00000000 [ 3222.586872] RTAS: event: 5, Type: Platform Error (224), Severity: 2 [ 3222.586873] EEH: Reset without hotplug activity [ 3224.762767] EEH: Beginning: 'slot_reset'
[ 3224.762770] EEH: PE#800000 (PCI 0384:80:00.0): Invoking
bnx2x->slot_reset()
[ 3224.762771] bnx2x: [bnx2x_io_slot_reset:14271(eth14)]IO slot reset initializing...
[ 3224.762887] bnx2x 0384:80:00.0: enabling device (0140 -> 0142) [ 3224.768157] bnx2x: [bnx2x_io_slot_reset:14287(eth14)]IO slot reset
--> driver unload

Uninterruptible tasks
=====================
crash> ps | grep UN
213 2 11 c000000004c89e00 UN 0.0 0 0 [eehd]
215 2 0 c000000004c80000 UN 0.0 0 0
[kworker/0:2]
2196 1 28 c000000004504f00 UN 0.1 15936 11136 wickedd
4287 1 9 c00000020d076800 UN 0.0 4032 3008 agetty
4289 1 20 c00000020d056680 UN 0.0 7232 3840 agetty
32423 2 26 c00000020038c580 UN 0.0 0 0
[kworker/26:3]
32871 4241 27 c0000002609ddd00 UN 0.1 18624 11648 sshd
32920 10130 16 c00000027284a100 UN 0.1 48512 12608 sendmail
33092 32987 0 c000000205218b00 UN 0.1 48512 12608 sendmail
33154 4567 16 c000000260e51780 UN 0.1 48832 12864 pickup
33209 4241 36 c000000270cb6500 UN 0.1 18624 11712 sshd
33473 33283 0 c000000205211480 UN 0.1 48512 12672 sendmail
33531 4241 37 c00000023c902780 UN 0.1 18624 11648 sshd

EEH handler hung while bnx2x sleeping and holding RTNL lock
===========================================================
crash> bt 213
PID: 213 TASK: c000000004c89e00 CPU: 11 COMMAND: "eehd"
#0 [c000000004d477e0] __schedule at c000000000c70808
#1 [c000000004d478b0] schedule at c000000000c70ee0
#2 [c000000004d478e0] schedule_timeout at c000000000c76dec
#3 [c000000004d479c0] msleep at c0000000002120cc
#4 [c000000004d479f0] napi_disable at c000000000a06448
^^^^^^^^^^^^^^^^
#5 [c000000004d47a30] bnx2x_netif_stop at c0080000018dba94 [bnx2x]
#6 [c000000004d47a60] bnx2x_io_slot_reset at c0080000018a551c [bnx2x]
#7 [c000000004d47b20] eeh_report_reset at c00000000004c9bc
#8 [c000000004d47b90] eeh_pe_report at c00000000004d1a8
#9 [c000000004d47c40] eeh_handle_normal_event at c00000000004da64

And the sleeping source code
============================
crash> dis -ls c000000000a06448
FILE: ../net/core/dev.c
LINE: 6702

6697 {
6698 might_sleep();
6699 set_bit(NAPI_STATE_DISABLE, &n->state);
6700
6701 while (test_and_set_bit(NAPI_STATE_SCHED, &n->state))
* 6702 msleep(1);
6703 while (test_and_set_bit(NAPI_STATE_NPSVC, &n->state))
6704 msleep(1);
6705
6706 hrtimer_cancel(&n->timer);
6707
6708 clear_bit(NAPI_STATE_DISABLE, &n->state);
6709 }

EEH calls into bnx2x twice based on the system log above, first through
bnx2x_io_error_detected() and then bnx2x_io_slot_reset(), and executes
the following call chains:

bnx2x_io_error_detected()
+-> bnx2x_eeh_nic_unload()
+-> bnx2x_del_all_napi()
+-> __netif_napi_del()

bnx2x_io_slot_reset()
+-> bnx2x_netif_stop()
+-> bnx2x_napi_disable()
+->napi_disable()

Fix this by correcting the sequence of NAPI APIs usage,
that is delete the NAPI after disabling it.

Fixes: 7fa6f34081f1 ("bnx2x: AER revised")
Reported-by: David Christensen <drc@linux.vnet.ibm.com>
Tested-by: David Christensen <drc@linux.vnet.ibm.com>
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Link: https://lore.kernel.org/r/20220426153913.6966-1-manishc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

bnx2x: fix built-in kernel driver load failure

[ Upstream commit 424e7834e293936a54fcf05173f2884171adc5a3 ]

Commit b7a49f73059f ("bnx2x: Utilize firmware 7.13.21.0")
added request_firmware() logic

bnx2x: fix built-in kernel driver load failure

[ Upstream commit 424e7834e293936a54fcf05173f2884171adc5a3 ]

Commit b7a49f73059f ("bnx2x: Utilize firmware 7.13.21.0")
added request_firmware() logic in probe() which caused
load failure when firmware file is not present in initrd (below),
as access to firmware file is not feasible during probe.

Direct firmware load for bnx2x/bnx2x-e2-7.13.15.0.fw failed with error -2
Direct firmware load for bnx2x/bnx2x-e2-7.13.21.0.fw failed with error -2

This patch fixes this issue by -

1. Removing request_firmware() logic from the probe()
such that .ndo_open() handle it as it used to handle
it earlier

2. Given request_firmware() is removed from probe(), so
driver has to relax FW version comparisons a bit against
the already loaded FW version (by some other PFs of same
adapter) to allow different compatible/close enough FWs with which
multiple PFs may run with (in different environments), as the
given PF who is in probe flow has no idea now with which firmware
file version it is going to initialize the device in ndo_open()

Link: https://lore.kernel.org/all/46f2d9d9-ae7f-b332-ddeb-b59802be2bab@molgen.mpg.de/
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Fixes: b7a49f73059f ("bnx2x: Utilize firmware 7.13.21.0")
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Link: https://lore.kernel.org/r/20220316214613.6884-1-manishc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

bnx2x: fix driver load from initrd

commit e13ad1443684f7afaff24cf207e85e97885256bd upstream.

Commit b7a49f73059f ("bnx2x: Utilize firmware 7.13.21.0") added
new firmware support in the driver with

bnx2x: fix driver load from initrd

commit e13ad1443684f7afaff24cf207e85e97885256bd upstream.

Commit b7a49f73059f ("bnx2x: Utilize firmware 7.13.21.0") added
new firmware support in the driver with maintaining older firmware
compatibility. However, older firmware was not added in MODULE_FIRMWARE()
which caused missing firmware files in initrd image leading to driver load
failure from initrd. This patch adds MODULE_FIRMWARE() for older firmware
version to have firmware files included in initrd.

Fixes: b7a49f73059f ("bnx2x: Utilize firmware 7.13.21.0")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215627
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Link: https://lore.kernel.org/r/20220223085720.12021-1-manishc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

bnx2x: Utilize firmware 7.13.21.0

commit b7a49f73059fe6147b6b78e8f674ce0d21237432 upstream

This new firmware addresses few important issues and enhancements
as mentioned below -

- Support direct i

bnx2x: Utilize firmware 7.13.21.0

commit b7a49f73059fe6147b6b78e8f674ce0d21237432 upstream

This new firmware addresses few important issues and enhancements
as mentioned below -

- Support direct invalidation of FP HSI Ver per function ID, required for
invalidating FP HSI Ver prior to each VF start, as there is no VF start
- BRB hardware block parity error detection support for the driver
- Fix the FCOE underrun flow
- Fix PSOD during FCoE BFS over the NIC ports after preboot driver
- Maintains backward compatibility

This patch incorporates this new firmware 7.13.21.0 in bnx2x driver.

Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

bnx2x: Search VPD with pci_vpd_find_ro_info_keyword()

Use pci_vpd_find_ro_info_keyword() to search for keywords in VPD to
simplify the code.

Use strncasecmp() to match Vendor ID instead of comparin

bnx2x: Search VPD with pci_vpd_find_ro_info_keyword()

Use pci_vpd_find_ro_info_keyword() to search for keywords in VPD to
simplify the code.

Use strncasecmp() to match Vendor ID instead of comparing with lower- and
upper-case hex string.

[bhelgaas: convert to strncasecmp()]
Link: https://lore.kernel.org/r/a9f730cf-e31e-902b-7b39-0ff2e99636e0@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

show more ...

bnx2x: Read VPD with pci_vpd_alloc()

Use pci_vpd_alloc() to dynamically allocate a properly sized buffer and
read the full VPD data into it.

This simplifies the code, and we no longer have to make

bnx2x: Read VPD with pci_vpd_alloc()

Use pci_vpd_alloc() to dynamically allocate a properly sized buffer and
read the full VPD data into it.

This simplifies the code, and we no longer have to make assumptions about
VPD size.

Link: https://lore.kernel.org/r/821a334d-ff9d-386e-5f42-9b620ab3dbfa@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

show more ...

Revert "bnx2x: Read VPD with pci_vpd_alloc()"

This reverts commit bed3db3d734e8e55815d865913ef75d9f707db96.

Signed-off-by: David S. Miller <davem@davemloft.net>

Revert "bnx2x: Search VPD with pci_vpd_find_ro_info_keyword()"

This reverts commit da417885a99d36036cc7d2778f94b846e6582434.

Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: Search VPD with pci_vpd_find_ro_info_keyword()

Use pci_vpd_find_ro_info_keyword() to search for keywords in VPD to
simplify the code.

str_id_reg and str_id_cap hold the same string and are u

bnx2x: Search VPD with pci_vpd_find_ro_info_keyword()

Use pci_vpd_find_ro_info_keyword() to search for keywords in VPD to
simplify the code.

str_id_reg and str_id_cap hold the same string and are used in the same
comparison. This doesn't make sense, use one string str_id instead.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

bnx2x: Read VPD with pci_vpd_alloc()

Use pci_vpd_alloc() to dynamically allocate a properly sized buffer and
read the full VPD data into it.

This simplifies the code, and we no longer have to make

bnx2x: Read VPD with pci_vpd_alloc()

Use pci_vpd_alloc() to dynamically allocate a properly sized buffer and
read the full VPD data into it.

This simplifies the code, and we no longer have to make assumptions about
VPD size.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...