drm/bridge: analogix_dp: Make PSR-exit block less

Prior to commit 6c836d965bad ("drm/rockchip: Use the helpers for PSR"),
"PSR exit" used non-blocking analogix_dp_send_psr_spd(). The refactor
starte

drm/bridge: analogix_dp: Make PSR-exit block less

Prior to commit 6c836d965bad ("drm/rockchip: Use the helpers for PSR"),
"PSR exit" used non-blocking analogix_dp_send_psr_spd(). The refactor
started using the blocking variant, for a variety of reasons -- quoting
Sean Paul's potentially-faulty memory:

"""
- To avoid racing a subsequent PSR entry (if exit takes a long time)
- To avoid racing disable/modeset
- We're not displaying new content while exiting PSR anyways, so there
is minimal utility in allowing frames to be submitted
- We're lying to userspace telling them frames are on the screen when
we're just dropping them on the floor
"""

However, I'm finding that this blocking transition is causing upwards of
60+ ms of unneeded latency on PSR-exit, to the point that initial cursor
movements when leaving PSR are unbearably jumpy.

It turns out that we need to meet in the middle somewhere: Sean is right
that we were "lying to userspace" with a non-blocking PSR-exit, but the
new blocking behavior is also waiting too long:

According to the eDP specification, the sink device must support PSR
entry transitions from both state 4 (ACTIVE_RESYNC) and state 0
(INACTIVE). It also states that in ACTIVE_RESYNC, "the Sink device must
display the incoming active frames from the Source device with no
visible glitches and/or artifacts."

Thus, for our purposes, we only need to wait for ACTIVE_RESYNC before
moving on; we are ready to display video, and subsequent PSR-entry is
safe.

Tested on a Samsung Chromebook Plus (i.e., Rockchip RK3399 Gru Kevin),
where this saves about 60ms of latency, for PSR-exit that used to
take about 80ms.

Fixes: 6c836d965bad ("drm/rockchip: Use the helpers for PSR")
Cc: <stable@vger.kernel.org>
Cc: Zain Wang <wzz@rock-chips.com>
Cc: Tomasz Figa <tfiga@chromium.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211103135112.v3.1.I67612ea073c3306c71b46a87be894f79707082df@changeid

show more ...

drm/bridge: analogix_dp: Make PSR-exit block less

commit c4c6ef229593366ab593d4d424addc7025b54a76 upstream.

Prior to commit 6c836d965bad ("drm/rockchip: Use the helpers for PSR"),
"PSR exit" used n

drm/bridge: analogix_dp: Make PSR-exit block less

commit c4c6ef229593366ab593d4d424addc7025b54a76 upstream.

Prior to commit 6c836d965bad ("drm/rockchip: Use the helpers for PSR"),
"PSR exit" used non-blocking analogix_dp_send_psr_spd(). The refactor
started using the blocking variant, for a variety of reasons -- quoting
Sean Paul's potentially-faulty memory:

"""
- To avoid racing a subsequent PSR entry (if exit takes a long time)
- To avoid racing disable/modeset
- We're not displaying new content while exiting PSR anyways, so there
is minimal utility in allowing frames to be submitted
- We're lying to userspace telling them frames are on the screen when
we're just dropping them on the floor
"""

However, I'm finding that this blocking transition is causing upwards of
60+ ms of unneeded latency on PSR-exit, to the point that initial cursor
movements when leaving PSR are unbearably jumpy.

It turns out that we need to meet in the middle somewhere: Sean is right
that we were "lying to userspace" with a non-blocking PSR-exit, but the
new blocking behavior is also waiting too long:

According to the eDP specification, the sink device must support PSR
entry transitions from both state 4 (ACTIVE_RESYNC) and state 0
(INACTIVE). It also states that in ACTIVE_RESYNC, "the Sink device must
display the incoming active frames from the Source device with no
visible glitches and/or artifacts."

Thus, for our purposes, we only need to wait for ACTIVE_RESYNC before
moving on; we are ready to display video, and subsequent PSR-entry is
safe.

Tested on a Samsung Chromebook Plus (i.e., Rockchip RK3399 Gru Kevin),
where this saves about 60ms of latency, for PSR-exit that used to
take about 80ms.

Fixes: 6c836d965bad ("drm/rockchip: Use the helpers for PSR")
Cc: <stable@vger.kernel.org>
Cc: Zain Wang <wzz@rock-chips.com>
Cc: Tomasz Figa <tfiga@chromium.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211103135112.v3.1.I67612ea073c3306c71b46a87be894f79707082df@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

gpu: drm: bridge: analogix: analogix_dp_reg: Remove unused function 'analogix_dp_write_byte_to_dpcd'

Fixes the following W=1 kernel build warning(s):

drivers/gpu/drm/bridge/analogix/analogix_dp_re

gpu: drm: bridge: analogix: analogix_dp_reg: Remove unused function 'analogix_dp_write_byte_to_dpcd'

Fixes the following W=1 kernel build warning(s):

drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c:571:5: warning: no previous prototype for ‘analogix_dp_write_byte_to_dpcd’ [-Wmissing-prototypes]

Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Jason Yan <yanaijie@huawei.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201105144517.1826692-13-lee.jones@linaro.org

show more ...

drm/bridge: analogix_dp: make analogix_dp_start_aux_transaction() static

This eliminates the following sparse warning:

drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c:527:5: warning: symbol
'anal

drm/bridge: analogix_dp: make analogix_dp_start_aux_transaction() static

This eliminates the following sparse warning:

drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c:527:5: warning: symbol
'analogix_dp_start_aux_transaction' was not declared. Should it be
static?

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200912033843.143240-1-yanaijie@huawei.com

show more ...

drm/bridge: analogix_dp: Convert to GPIO descriptors

This converts the Analogix display port to use GPIO descriptors
instead of DT-extracted numbers.

Cc: Douglas Anderson <dianders@chromium.org>
Cc

drm/bridge: analogix_dp: Convert to GPIO descriptors

This converts the Analogix display port to use GPIO descriptors
instead of DT-extracted numbers.

Cc: Douglas Anderson <dianders@chromium.org>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190609231339.22136-1-linus.walleij@linaro.org

show more ...

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 152

Based on 1 normalized pattern(s):

this program is free software you can redistribute it and or modify
it under the terms of th

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 152

Based on 1 normalized pattern(s):

this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version

extracted by the scancode license scanner the SPDX license identifier

GPL-2.0-or-later

has been chosen to replace the boilerplate/reference in 3029 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

drm: Rename struct edp_vsc_psr to struct dp_sdp

VSC SDP Payload for PSR is one of data block type of SDP (Secondaray Data
Packet). In order to generalize SDP packet structure name, it renames
struct

drm: Rename struct edp_vsc_psr to struct dp_sdp

VSC SDP Payload for PSR is one of data block type of SDP (Secondaray Data
Packet). In order to generalize SDP packet structure name, it renames
struct edp_vsc_psr to struct dp_sdp. And each SDP data blocks have
different usages, each SDP type has different reserved data blocks and
Video_Stream_Configuration Extension VESA SDP might use all of Data Blocks
as Extended INFORFRAME Data Byte. so it makes Data Block variables as
array type. And it adds comments of details of DB of VSC SDP Payload
for Pixel Encoding/Colorimetry Format. This comments follows DP 1.4a spec,
section 2.2.5.7.5, chapter "VSC SDP Payload for Pixel Encoding/Colorimetry
Format".

v7: Addressed review comments from Ville.

v9: Rename a member value name DB to db on struct dp_sdp [Laurent]

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190521121721.32010-3-gwan-gyeong.mun@intel.com

show more ...

drm/bridge: analogix_dp: Properly disable aux chan retries on rockchip

The comments in analogix_dp_init_aux() claim that we're disabling aux
channel retries, but then right below it for Rockchip it

drm/bridge: analogix_dp: Properly disable aux chan retries on rockchip

The comments in analogix_dp_init_aux() claim that we're disabling aux
channel retries, but then right below it for Rockchip it sets them to
3. If we actually need 3 retries for Rockchip then we could adjust
the comment, but it seems more likely that we want the same retry
behavior across all platforms.

Cc: Stéphane Marchesin <marcheu@chromium.org>
Cc: 征增 王 <wzz@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-21-enric.balletbo@collabora.com

show more ...

drm/bridge: analogix_dp: Properly log AUX CH errors

The code in analogix_dp_transfer() that was supposed to print out:
AUX CH error happened

Was actually dead code. That's because the previous ch

drm/bridge: analogix_dp: Properly log AUX CH errors

The code in analogix_dp_transfer() that was supposed to print out:
AUX CH error happened

Was actually dead code. That's because the previous check (whether
the interrupt status indicated any errors) would have hit for all
errors anyway.

Let's combine the two error checks so we can actually see AUX CH
errors. We'll also downgrade the message to a warning since some of
these types of errors might be expected for some displays. If this
gets too noisy we can downgrade again to debug.

Cc: 征增 王 <wzz@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-20-enric.balletbo@collabora.com

show more ...

drm/bridge: analogix_dp: Fix incorrect operations with register ANALOGIX_DP_FUNC_EN_1

Register ANALOGIX_DP_FUNC_EN_1(offset 0x18), Rockchip is different to
Exynos:

on Exynos edp phy,
BIT 7 MASTER_

drm/bridge: analogix_dp: Fix incorrect operations with register ANALOGIX_DP_FUNC_EN_1

Register ANALOGIX_DP_FUNC_EN_1(offset 0x18), Rockchip is different to
Exynos:

on Exynos edp phy,
BIT 7 MASTER_VID_FUNC_EN_N
BIT 6 reserved
BIT 5 SLAVE_VID_FUNC_EN_N

on Rockchip edp phy,
BIT 7 reserved
BIT 6 RK_VID_CAP_FUNC_EN_N
BIT 5 RK_VID_FIFO_FUNC_EN_N

So, we should do some private operations to Rockchip.

Cc: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-17-enric.balletbo@collabora.com

show more ...

drm/bridge: analogix_dp: Don't use ANALOGIX_DP_PLL_CTL to control pll

There is no register named ANALOGIX_DP_PLL_CTL in Rockchip edp phy reg
list. We should use BIT_4 in ANALOGIX_DP_PD to control t

drm/bridge: analogix_dp: Don't use ANALOGIX_DP_PLL_CTL to control pll

There is no register named ANALOGIX_DP_PLL_CTL in Rockchip edp phy reg
list. We should use BIT_4 in ANALOGIX_DP_PD to control the pll power
instead of ANALOGIX_DP_PLL_CTL.

Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-15-enric.balletbo@collabora.com

show more ...

drm/bridge: analogix_dp: Reset aux channel if an error occurred

AUX errors are caused by many different reasons. We may not know what
happened in aux channel on failure, so let's reset aux channel i

drm/bridge: analogix_dp: Reset aux channel if an error occurred

AUX errors are caused by many different reasons. We may not know what
happened in aux channel on failure, so let's reset aux channel if some
errors occurred.

Cc: 征增 王 <wzz@rock-chips.com>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-13-enric.balletbo@collabora.com

show more ...

drm/bridge: analogix_dp: Fix AUX_PD bit for Rockchip

There are some different bits between Rockchip and Exynos in register
"AUX_PD". This patch fixes the incorrect operations about it.

Cc: Douglas

drm/bridge: analogix_dp: Fix AUX_PD bit for Rockchip

There are some different bits between Rockchip and Exynos in register
"AUX_PD". This patch fixes the incorrect operations about it.

Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-12-enric.balletbo@collabora.com

show more ...

drm/bridge: analogix_dp: Set PD_INC_BG first when powering up edp phy

Following the correct power up sequence:
dp_pd=ff => dp_pd=7f => wait 10us => dp_pd=00

Cc: Stéphane Marchesin <marcheu@chromium

drm/bridge: analogix_dp: Set PD_INC_BG first when powering up edp phy

Following the correct power up sequence:
dp_pd=ff => dp_pd=7f => wait 10us => dp_pd=00

Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-7-enric.balletbo@collabora.com

show more ...

drm/bridge: analogix_dp: Retry bridge enable when it failed

When we enable bridge failed, we have to retry it, otherwise we would get
the abnormal display.

Cc: Stéphane Marchesin <marcheu@chromium.

drm/bridge: analogix_dp: Retry bridge enable when it failed

When we enable bridge failed, we have to retry it, otherwise we would get
the abnormal display.

Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-5-enric.balletbo@collabora.com

show more ...

drm/bridge: analogix_dp: Check AUX_EN status when doing AUX transfer

We should check AUX_EN bit to confirm the AUX CH operation is completed.

Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-of

drm/bridge: analogix_dp: Check AUX_EN status when doing AUX transfer

We should check AUX_EN bit to confirm the AUX CH operation is completed.

Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-3-enric.balletbo@collabora.com

show more ...

drm/bridge: analogix_dp: Only wait for panel ACK on PSR entry

We currently wait for the panel to mirror our intended PSR state
before continuing on both PSR enter and PSR exit. This is really
only i

drm/bridge: analogix_dp: Only wait for panel ACK on PSR entry

We currently wait for the panel to mirror our intended PSR state
before continuing on both PSR enter and PSR exit. This is really
only important to do when we're entering PSR, since we want to
be sure the last frame we pushed is being served from the panel's
internal fb before shutting down the soc blocks (vop/analogix).

This patch changes the behavior such that we only wait for the
panel to complete the PSR transition when we're entering PSR, and
to skip verification when we're exiting.

Cc: Stéphane Marchesin <marcheu@chromium.org>
Cc: Sonny Rao <sonnyrao@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180309222327.18689-7-enric.balletbo@collabora.com

show more ...

drm/bridge: analogix_dp: detect Sink PSR state after configuring the PSR

Make sure the request PSR state takes effect in analogix_dp_send_psr_spd()
function, or print the sink PSR error state if we

drm/bridge: analogix_dp: detect Sink PSR state after configuring the PSR

Make sure the request PSR state takes effect in analogix_dp_send_psr_spd()
function, or print the sink PSR error state if we failed to apply the
requested PSR setting.

Cc: 征增 王 <wzz@rock-chips.com>
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
[seanpaul changed timeout loop to a readx poll]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180309222327.18689-2-enric.balletbo@collabora.com

show more ...

drm/bridge: analogix_dp: return error if transfer none byte

Reference from drm_dp_aux description (about transfer):
Upon success, the implementation should return the number of payload bytes
that we

drm/bridge: analogix_dp: return error if transfer none byte

Reference from drm_dp_aux description (about transfer):
Upon success, the implementation should return the number of payload bytes
that were transferred, or a negative error-code on failure. Helpers
propagate errors from the .transfer() function, with the exception of
the -EBUSY error, which causes a transaction to be retried. On a short,
helpers will return -EPROTO to make it simpler to check for failure.

The analogix_dp_transfer will return num_transferred, but if there is none
byte been transferred, the return value will be 0, which means success, we
should return error-code if transfer none byte.

for (retry = 0; retry < 32; retry++) {
err = aux->transfer(aux, &msg);
if (err < 0) {
if (err == -EBUSY)
continue;

goto unlock;
}
}

Cc: zain wang <wzz@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1479255219-7243-1-git-send-email-jay.xu@rock-chips.com

show more ...

drm/bridge: analogix_dp: Remove duplicated code

Remove code for reading the EDID and DPCD fields and use the helpers
instead.

Besides the obvious code reduction, other helpers are being added to th

drm/bridge: analogix_dp: Remove duplicated code

Remove code for reading the EDID and DPCD fields and use the helpers
instead.

Besides the obvious code reduction, other helpers are being added to the
core that could be used in this driver and will be good to be able to
use them instead of duplicating them.

Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Yakir Yang <ykk@rock-chips.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Archit Taneja <architt@codeaurora.org>

show more ...

drm/bridge: analogix_dp: Remove duplicated code

Remove code for reading the EDID and DPCD fields and use the helpers
instead.

Besides the obvious code reduction, other helpers are being added to th

drm/bridge: analogix_dp: Remove duplicated code

Remove code for reading the EDID and DPCD fields and use the helpers
instead.

Besides the obvious code reduction, other helpers are being added to the
core that could be used in this driver and will be good to be able to
use them instead of duplicating them.

Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Yakir Yang <ykk@rock-chips.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Archit Taneja <architt@codeaurora.org>

show more ...

drm/bridge: analogix_dp: squash lines for simple wrapper functions

Remove unneeded variables and assignments.

Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Masahiro

drm/bridge: analogix_dp: squash lines for simple wrapper functions

Remove unneeded variables and assignments.

Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[seanpaul added analogix prefix to subject]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1473863952-7658-4-git-send-email-yamada.masahiro@socionext.com

show more ...

drm/bridge: analogix_dp: add the PSR function support

The full name of PSR is Panel Self Refresh, panel device could refresh
itself with the hardware framebuffer in panel, this would make lots of
se

drm/bridge: analogix_dp: add the PSR function support

The full name of PSR is Panel Self Refresh, panel device could refresh
itself with the hardware framebuffer in panel, this would make lots of
sense to save the power consumption.

This patch have exported two symbols for platform driver to implement
the PSR function in hardware side:
- analogix_dp_active_psr()
- analogix_dp_inactive_psr()

Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>

show more ...

drm/bridge: analogix_dp: some rockchip chips need to flip REF_CLK bit setting

As vendor document indicate, when REF_CLK bit set 0, then DP
phy's REF_CLK should switch to 24M source clock.

But due t

drm/bridge: analogix_dp: some rockchip chips need to flip REF_CLK bit setting

As vendor document indicate, when REF_CLK bit set 0, then DP
phy's REF_CLK should switch to 24M source clock.

But due to IC PHY layout mistaken, some chips need to flip this
bit(like RK3288), and unfortunately they didn't indicate in the
DP version register. That's why we have to make this little hack.

Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Tomasz Figa <tomasz.figa@chromium.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>

show more ...

drm: bridge: analogix/dp: Fix the possible dead lock in bridge disable time

It may caused a dead lock if we flush the hpd work in bridge disable time.

The normal flow would like:
IN --> DRM IOCTL

drm: bridge: analogix/dp: Fix the possible dead lock in bridge disable time

It may caused a dead lock if we flush the hpd work in bridge disable time.

The normal flow would like:
IN --> DRM IOCTL
1. Acquire crtc_ww_class_mutex (DRM IOCTL)
IN --> analogix_dp_bridge
2. Acquire hpd work lock (Flush hpd work)
3. HPD work already in idle, no need to run the work function.
OUT <-- analogix_dp_bridge
OUT <-- DRM IOCTL

The dead lock flow would like:
IN --> DRM IOCTL
1. Acquire crtc_ww_class_mutex (DRM IOCTL)
IN --> analogix_dp_bridge
2. Acquire hpd work lock (Flush hpd work)
IN --> analogix_dp_hotplug
IN --> drm_helper_hpd_irq_event
3. Acquire mode_config lock (This lock already have been acquired in previous step 1)
** Dead Lock Now **

It's wrong to flush the hpd work in bridge->disable time, I guess the
original code just want to ensure the delay work must be finish before
encoder disabled.

The flush work in bridge disable time is try to ensure the HPD event
won't be missed before display card disabled, actually we can take a
fast respond way(interrupt thread) to update DRM HPD event to fix the
delay update and possible dead lock.

Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>

show more ...