gpio: pcf857x: Extend match data support for OF tables

The driver has OF match table, but still it uses an ID lookup table for
retrieving match data. Currently, the driver is working on the
assumpti

gpio: pcf857x: Extend match data support for OF tables

The driver has OF match table, but still it uses an ID lookup table for
retrieving match data. Currently, the driver is working on the
assumption that an I2C device registered via OF will always match a
legacy I2C device ID. Extend match data support for OF tables by using
i2c_get_match_data() instead of the ID lookup for both OF/ID matches by
making similar OF/ID tables.

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

show more ...

gpio: Switch i2c drivers back to use .probe()

After commit b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498b5 ("

gpio: Switch i2c drivers back to use .probe()

After commit b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498b5 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

show more ...

gpio: pcf857x: Drop unneeded explicit casting

The s32 is compatible with int, no need to cast.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.w

gpio: pcf857x: Drop unneeded explicit casting

The s32 is compatible with int, no need to cast.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

show more ...

gpio: pcf857x: Make use of device properties

Convert the module to be property provider agnostic and allow
it to be used on non-OF platforms.

Add mod_devicetable.h include.

Signed-off-by: Andy She

gpio: pcf857x: Make use of device properties

Convert the module to be property provider agnostic and allow
it to be used on non-OF platforms.

Add mod_devicetable.h include.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

show more ...

gpio: pcf857x: Get rid of legacy platform data

Platform data is a legacy interface to supply device properties
to the driver. In this case we don't have in-kernel users for it.
Moreover it uses plai

gpio: pcf857x: Get rid of legacy platform data

Platform data is a legacy interface to supply device properties
to the driver. In this case we don't have in-kernel users for it.
Moreover it uses plain GPIO numbers which is no-no for a new code.

Just remove it for good.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

show more ...

gpio: pcf857x: Implement get_multiple/set_multiple methods

This change allows the GPIO core to read/change multiple pins in a
single driver call and subsequent I2C transfer. It helps a lot with
PCF8

gpio: pcf857x: Implement get_multiple/set_multiple methods

This change allows the GPIO core to read/change multiple pins in a
single driver call and subsequent I2C transfer. It helps a lot with
PCF857x devices, since their I2C protocol always reads/changes all
existing pins anyway. Therefore, when the GPIO client code does a bulk
operation on multiple pins, the driver makes a single I2C transfer.

Signed-off-by: Radu Rendec <radu.rendec@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

show more ...

gpio: pcf857x: Fix indentation of variable declarations

No functional changes. This is a whitespace change only.

Signed-off-by: Radu Rendec <radu.rendec@gmail.com>
Signed-off-by: Bartosz Golaszewsk

gpio: pcf857x: Fix indentation of variable declarations

No functional changes. This is a whitespace change only.

Signed-off-by: Radu Rendec <radu.rendec@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

show more ...

gpio: pcf857x: Replace 'unsigned' with 'unsigned int'

Cosmetic change only to improve the coding style. No functional change,
since 'unsigned' and 'unsigned int' are identical as far as the compiler

gpio: pcf857x: Replace 'unsigned' with 'unsigned int'

Cosmetic change only to improve the coding style. No functional change,
since 'unsigned' and 'unsigned int' are identical as far as the compiler
is concerned.

Signed-off-by: Radu Rendec <radu.rendec@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

show more ...

gpio: pcf857x: Convert to i2c's .probe_new()

.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.

Signed-off-by: Uwe Kleine-König <u.kleine-ko

gpio: pcf857x: Convert to i2c's .probe_new()

.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

show more ...

i2c: Make remove callback return void

The value returned by an i2c driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)

i2c: Make remove callback return void

The value returned by an i2c driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)

So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.

Reviewed-by: Peter Senna Tschudin <peter.senna@gmail.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marek Behún <kabel@kernel.org> # for leds-turris-omnia
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for surface3_power
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> # for bmc150-accel-i2c + kxcjk-1013
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for media/* + staging/media/*
Acked-by: Miguel Ojeda <ojeda@kernel.org> # for auxdisplay/ht16k33 + auxdisplay/lcd2s
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for versaclock5
Reviewed-by: Ajay Gupta <ajayg@nvidia.com> # for ucsi_ccg
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio
Acked-by: Peter Rosin <peda@axentia.se> # for i2c-mux-*, max9860
Acked-by: Adrien Grassein <adrien.grassein@gmail.com> # for lontium-lt8912b
Reviewed-by: Jean Delvare <jdelvare@suse.de> # for hwmon, i2c-core and i2c/muxes
Acked-by: Corey Minyard <cminyard@mvista.com> # for IPMI
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for drivers/power
Acked-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

show more ...

gpio: pcf857x: Make the irqchip immutable

Commit 6c846d026d49 ("gpio: Don't fiddle with irqchips marked as
immutable") added a warning to indicate if the gpiolib is altering the
internals of irqchip

gpio: pcf857x: Make the irqchip immutable

Commit 6c846d026d49 ("gpio: Don't fiddle with irqchips marked as
immutable") added a warning to indicate if the gpiolib is altering the
internals of irqchips. Following this change the following warning is
now observed for the pcf857x driver:

gpio gpiochip1: (pcf8575): not an immutable chip, please consider fixing it!

Fix this by making the irqchip in the pcf857x driver immutable.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

show more ...

gpio: pcf857x: Make teardown callback return void

All teardown functions return 0. Also there is little sense in returning
a negative error code from an i2c remove function as this only results in
e

gpio: pcf857x: Make teardown callback return void

All teardown functions return 0. Also there is little sense in returning
a negative error code from an i2c remove function as this only results in
emitting an error message but the device is removed nevertheless.

This patch is a preparation for making i2c remove callbacks return void.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

show more ...

gpio: pcf857x: Fix missing first interrupt

If no n_latch value will be provided at driver probe then all pins will
be used as an input:

gpio->out = ~n_latch;

In that case initial state for all

gpio: pcf857x: Fix missing first interrupt

If no n_latch value will be provided at driver probe then all pins will
be used as an input:

gpio->out = ~n_latch;

In that case initial state for all pins is "one":

gpio->status = gpio->out;

So if pcf857x IRQ happens with change pin value from "zero" to "one"
then we miss it, because of "one" from IRQ and "one" from initial state
leaves corresponding pin unchanged:
change = (gpio->status ^ status) & gpio->irq_enabled;

The right solution will be to read actual state at driver probe.

Cc: stable@vger.kernel.org
Fixes: 6e20a0a429bd ("gpio: pcf857x: enable gpio_to_irq() support")
Signed-off-by: Maxim Kiselev <bigunclemax@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

show more ...

gpio: pcf857x: Fix missing first interrupt

commit a8002a35935aaefcd6a42ad3289f62bab947f2ca upstream.

If no n_latch value will be provided at driver probe then all pins will
be used as an input:

gpio: pcf857x: Fix missing first interrupt

commit a8002a35935aaefcd6a42ad3289f62bab947f2ca upstream.

If no n_latch value will be provided at driver probe then all pins will
be used as an input:

gpio->out = ~n_latch;

In that case initial state for all pins is "one":

gpio->status = gpio->out;

So if pcf857x IRQ happens with change pin value from "zero" to "one"
then we miss it, because of "one" from IRQ and "one" from initial state
leaves corresponding pin unchanged:
change = (gpio->status ^ status) & gpio->irq_enabled;

The right solution will be to read actual state at driver probe.

Cc: stable@vger.kernel.org
Fixes: 6e20a0a429bd ("gpio: pcf857x: enable gpio_to_irq() support")
Signed-off-by: Maxim Kiselev <bigunclemax@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

gpio: pcf857x: Use irqchip template

This makes the driver use the irqchip template to assign
properties to the gpio_irq_chip instead of using the
explicit calls to gpiochip_irqchip_add_nested() and

gpio: pcf857x: Use irqchip template

This makes the driver use the irqchip template to assign
properties to the gpio_irq_chip instead of using the
explicit calls to gpiochip_irqchip_add_nested() and
gpiochip_set_nested_irqchip(). The irqchip is instead
added while adding the gpiochip.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Anders Darander <anders@chargestorm.se>
Cc: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20200717144835.68150-1-linus.walleij@linaro.org

show more ...

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 61

Based on 1 normalized pattern(s):

this program is free software you can redistribute it and or modify
it under the terms of the

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 61

Based on 1 normalized pattern(s):

this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
675 mass ave cambridge ma 02139 usa

extracted by the scancode license scanner the SPDX license identifier

GPL-2.0-or-later

has been chosen to replace the boilerplate/reference in 441 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520071858.739733335@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

gpio: pcf857x: Simpify wake-up handling

Unlike gpio_rcar_irq_set_wake(), which this solution was based on,
pcf857x_irq_set_wake() does not need to do anything else than calling
irq_set_irq_wake() fo

gpio: pcf857x: Simpify wake-up handling

Unlike gpio_rcar_irq_set_wake(), which this solution was based on,
pcf857x_irq_set_wake() does not need to do anything else than calling
irq_set_irq_wake() for the upstream interrupt controller. Hence there
is no reason for making this call conditional, and no longer a need for
keeping a copy of the interrupt number that also serves as a flag.

Just propagate irq_set_irq_wake() to the upstream interrupt controller,
using the original interrupt number.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

show more ...

gpio: pcf857x: Fix interrupts on multiple instances

When multiple instances of pcf857x chips are present, a fix up
message [1] is printed during the probe of the 2nd and later
instances.

The issue

gpio: pcf857x: Fix interrupts on multiple instances

When multiple instances of pcf857x chips are present, a fix up
message [1] is printed during the probe of the 2nd and later
instances.

The issue is that the driver is using the same irq_chip data
structure between multiple instances.

Fix this by allocating the irq_chip data structure per instance.

[1] fix up message addressed by this patch
[ 1.212100] gpio gpiochip9: (pcf8575): detected irqchip that is shared with multiple gpiochips: please fix the driver.

Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

show more ...

gpio: pcf857x: Include the right header

This is a GPIO driver, include only <linux/gpio/driver.h>.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

gpio: Move irqdomain into struct gpio_irq_chip

In order to consolidate the multiple ways to associate an IRQ chip with
a GPIO chip, move more fields into the new struct gpio_irq_chip.

Signed-off-by

gpio: Move irqdomain into struct gpio_irq_chip

In order to consolidate the multiple ways to associate an IRQ chip with
a GPIO chip, move more fields into the new struct gpio_irq_chip.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

show more ...

gpio: pcf857x: move header file out of I2C realm

include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Si

gpio: pcf857x: move header file out of I2C realm

include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

show more ...

gpio: move tca9554 from pcf857x to pca953x

The TCA9554 doesn't work with the pcf857x driver, trying to change the direction
gives a NAK bailout error.

TCA9554 is similar to the PCA9554, thus change

gpio: move tca9554 from pcf857x to pca953x

The TCA9554 doesn't work with the pcf857x driver, trying to change the direction
gives a NAK bailout error.

TCA9554 is similar to the PCA9554, thus change the driver.

Signed-off-by: Anders Darander <anders@chargestorm.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

show more ...

gpio: simplify adding threaded interrupts

This tries to simplify the use of CONFIG_GPIOLIB_IRQCHIP when
using threaded interrupts: add a new call
gpiochip_irqchip_add_nested() to indicate that we're

gpio: simplify adding threaded interrupts

This tries to simplify the use of CONFIG_GPIOLIB_IRQCHIP when
using threaded interrupts: add a new call
gpiochip_irqchip_add_nested() to indicate that we're dealing
with a nested rather than a chained irqchip, then create a
separate gpiochip_set_nested_irqchip() to mirror
the gpiochip_set_chained_irqchip() call to connect the
parent and child interrupts.

In the nested case gpiochip_set_nested_irqchip() does nothing
more than call irq_set_parent() on each valid child interrupt,
which has little semantic effect in the kernel, but this is
probably still formally correct.

Update all drivers using nested interrupts to use
gpiochip_irqchip_add_nested() so we can now see clearly
which these users are.

The DLN2 driver can drop its specific hack with
.irq_not_threaded as we now recognize whether a chip is
threaded or not from its use of gpiochip_irqchip_add_nested()
signature rather than from inspecting .can_sleep.

We rename the .irq_parent to .irq_chained_parent since this
parent IRQ is only really kept around for the chained
interrupt handlers.

Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Octavian Purdila <octavian.purdila@intel.com>
Cc: Daniel Baluta <daniel.baluta@intel.com>
Cc: Bin Gao <bin.gao@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Ajay Thomas <ajay.thomas.david.rajamanickam@intel.com>
Cc: Semen Protsenko <semen.protsenko@globallogic.com>
Cc: Alexander Stein <alexander.stein@systec-electronic.com>
Cc: Phil Reid <preid@electromag.com.au>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

show more ...

gpio: pcf857x: restore the initial line state of all pcf lines

The reset values for all the PCF lines are high and hence on
shutdown we should drive all the lines high in order to
bring it to the re

gpio: pcf857x: restore the initial line state of all pcf lines

The reset values for all the PCF lines are high and hence on
shutdown we should drive all the lines high in order to
bring it to the reset state.

This is actually required since PCF doesn't have a reset
line and even after warm reset (by invoking "reboot" in
prompt) the PCF lines maintains it's previous programmed
state. This becomes a problem if the boards are designed to
work with the default initial state.

DRA7XX_evm uses PCF8575 and one of the PCF output lines
feeds to MMC/SD VDD and this line should be driven high in order
for the MMC/SD to be detected. This line is modelled as
regulator and the hsmmc driver takes care of enabling and
disabling it. In the case of 'reboot', during shutdown path
as part of it's cleanup process the hsmmc driver disables
this regulator. This makes MMC *boot* not functional.

Fix it by driving all the pcf lines high.

This patch was sent long back
(https://patchwork.ozlabs.org/patch/420382/)
But there was a concern that contention might occur if the
PCF shutdown handler is invoked before the shutdown handler
of the PCF's consumers. In that case PCF shutdown handler can't
drive all the pcf lines high without knowing if the PCF
consumers are still active.

However commit 52cdbdd4985 ("driver core: correct device's
shutdown order") will make sure shutdown handler of PCF's
consumers are invoked before invoking the shutdown
handler of PCF. So it should be safe to merge this now.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

show more ...

gpio: pcf857x: Use devm_gpiochip_add_data() for gpio registration

Use devm_gpiochip_add_data() for GPIO registration and clean the
error path.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>