atm: lanai: dont run lanai_dev_close if not open

lanai_dev_open() can fail. When it fail, lanai->base is unmapped and the
pci device is disabled. The caller, lanai_init_one(), then tries to run
atm_

atm: lanai: dont run lanai_dev_close if not open

lanai_dev_open() can fail. When it fail, lanai->base is unmapped and the
pci device is disabled. The caller, lanai_init_one(), then tries to run
atm_dev_deregister(). This will subsequently call lanai_dev_close() and
use the already released MMIO area.

To fix this issue, set the lanai->base to NULL if open fail,
and test the flag in lanai_dev_close().

[ 8.324153] lanai: lanai_start() failed, err=19
[ 8.324819] lanai(itf 0): shutting down interface
[ 8.325211] BUG: unable to handle page fault for address: ffffc90000180024
[ 8.325781] #PF: supervisor write access in kernel mode
[ 8.326215] #PF: error_code(0x0002) - not-present page
[ 8.326641] PGD 100000067 P4D 100000067 PUD 100139067 PMD 10013a067 PTE 0
[ 8.327206] Oops: 0002 [#1] SMP KASAN NOPTI
[ 8.327557] CPU: 0 PID: 95 Comm: modprobe Not tainted 5.11.0-rc7-00090-gdcc0b49040c7 #12
[ 8.328229] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-48-gd9c812dda519-4
[ 8.329145] RIP: 0010:lanai_dev_close+0x4f/0xe5 [lanai]
[ 8.329587] Code: 00 48 c7 c7 00 d3 01 c0 e8 49 4e 0a c2 48 8d bd 08 02 00 00 e8 6e 52 14 c1 48 80
[ 8.330917] RSP: 0018:ffff8881029ef680 EFLAGS: 00010246
[ 8.331196] RAX: 000000000003fffe RBX: ffff888102fb4800 RCX: ffffffffc001a98a
[ 8.331572] RDX: ffffc90000180000 RSI: 0000000000000246 RDI: ffff888102fb4000
[ 8.331948] RBP: ffff888102fb4000 R08: ffffffff8115da8a R09: ffffed102053deaa
[ 8.332326] R10: 0000000000000003 R11: ffffed102053dea9 R12: ffff888102fb48a4
[ 8.332701] R13: ffffffffc00123c0 R14: ffff888102fb4b90 R15: ffff888102fb4b88
[ 8.333077] FS: 00007f08eb9056a0(0000) GS:ffff88815b400000(0000) knlGS:0000000000000000
[ 8.333502] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 8.333806] CR2: ffffc90000180024 CR3: 0000000102a28000 CR4: 00000000000006f0
[ 8.334182] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 8.334557] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 8.334932] Call Trace:
[ 8.335066] atm_dev_deregister+0x161/0x1a0 [atm]
[ 8.335324] lanai_init_one.cold+0x20c/0x96d [lanai]
[ 8.335594] ? lanai_send+0x2a0/0x2a0 [lanai]
[ 8.335831] local_pci_probe+0x6f/0xb0
[ 8.336039] pci_device_probe+0x171/0x240
[ 8.336255] ? pci_device_remove+0xe0/0xe0
[ 8.336475] ? kernfs_create_link+0xb6/0x110
[ 8.336704] ? sysfs_do_create_link_sd.isra.0+0x76/0xe0
[ 8.336983] really_probe+0x161/0x420
[ 8.337181] driver_probe_device+0x6d/0xd0
[ 8.337401] device_driver_attach+0x82/0x90
[ 8.337626] ? device_driver_attach+0x90/0x90
[ 8.337859] __driver_attach+0x60/0x100
[ 8.338065] ? device_driver_attach+0x90/0x90
[ 8.338298] bus_for_each_dev+0xe1/0x140
[ 8.338511] ? subsys_dev_iter_exit+0x10/0x10
[ 8.338745] ? klist_node_init+0x61/0x80
[ 8.338956] bus_add_driver+0x254/0x2a0
[ 8.339164] driver_register+0xd3/0x150
[ 8.339370] ? 0xffffffffc0028000
[ 8.339550] do_one_initcall+0x84/0x250
[ 8.339755] ? trace_event_raw_event_initcall_finish+0x150/0x150
[ 8.340076] ? free_vmap_area_noflush+0x1a5/0x5c0
[ 8.340329] ? unpoison_range+0xf/0x30
[ 8.340532] ? ____kasan_kmalloc.constprop.0+0x84/0xa0
[ 8.340806] ? unpoison_range+0xf/0x30
[ 8.341014] ? unpoison_range+0xf/0x30
[ 8.341217] do_init_module+0xf8/0x350
[ 8.341419] load_module+0x3fe6/0x4340
[ 8.341621] ? vm_unmap_ram+0x1d0/0x1d0
[ 8.341826] ? ____kasan_kmalloc.constprop.0+0x84/0xa0
[ 8.342101] ? module_frob_arch_sections+0x20/0x20
[ 8.342358] ? __do_sys_finit_module+0x108/0x170
[ 8.342604] __do_sys_finit_module+0x108/0x170
[ 8.342841] ? __ia32_sys_init_module+0x40/0x40
[ 8.343083] ? file_open_root+0x200/0x200
[ 8.343298] ? do_sys_open+0x85/0xe0
[ 8.343491] ? filp_open+0x50/0x50
[ 8.343675] ? exit_to_user_mode_prepare+0xfc/0x130
[ 8.343935] do_syscall_64+0x33/0x40
[ 8.344132] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 8.344401] RIP: 0033:0x7f08eb887cf7
[ 8.344594] Code: 48 89 57 30 48 8b 04 24 48 89 47 38 e9 1d a0 02 00 48 89 f8 48 89 f7 48 89 d6 41
[ 8.345565] RSP: 002b:00007ffcd5c98ad8 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
[ 8.345962] RAX: ffffffffffffffda RBX: 00000000008fea70 RCX: 00007f08eb887cf7
[ 8.346336] RDX: 0000000000000000 RSI: 00000000008fd9e0 RDI: 0000000000000003
[ 8.346711] RBP: 0000000000000003 R08: 0000000000000000 R09: 0000000000000001
[ 8.347085] R10: 00007f08eb8eb300 R11: 0000000000000246 R12: 00000000008fd9e0
[ 8.347460] R13: 0000000000000000 R14: 00000000008fddd0 R15: 0000000000000001
[ 8.347836] Modules linked in: lanai(+) atm
[ 8.348065] CR2: ffffc90000180024
[ 8.348244] ---[ end trace 7fdc1c668f2003e5 ]---
[ 8.348490] RIP: 0010:lanai_dev_close+0x4f/0xe5 [lanai]
[ 8.348772] Code: 00 48 c7 c7 00 d3 01 c0 e8 49 4e 0a c2 48 8d bd 08 02 00 00 e8 6e 52 14 c1 48 80
[ 8.349745] RSP: 0018:ffff8881029ef680 EFLAGS: 00010246
[ 8.350022] RAX: 000000000003fffe RBX: ffff888102fb4800 RCX: ffffffffc001a98a
[ 8.350397] RDX: ffffc90000180000 RSI: 0000000000000246 RDI: ffff888102fb4000
[ 8.350772] RBP: ffff888102fb4000 R08: ffffffff8115da8a R09: ffffed102053deaa
[ 8.351151] R10: 0000000000000003 R11: ffffed102053dea9 R12: ffff888102fb48a4
[ 8.351525] R13: ffffffffc00123c0 R14: ffff888102fb4b90 R15: ffff888102fb4b88
[ 8.351918] FS: 00007f08eb9056a0(0000) GS:ffff88815b400000(0000) knlGS:0000000000000000
[ 8.352343] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 8.352647] CR2: ffffc90000180024 CR3: 0000000102a28000 CR4: 00000000000006f0
[ 8.353022] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 8.353397] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 8.353958] modprobe (95) used greatest stack depth: 26216 bytes left

Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

atm: lanai: Remove in_interrupt() usage

lanai_shutdown_tx_vci() uses in_interrupt() to issue a warning message
if the function was used in context in which it is not safe to sleep.

The usage of in_

atm: lanai: Remove in_interrupt() usage

lanai_shutdown_tx_vci() uses in_interrupt() to issue a warning message
if the function was used in context in which it is not safe to sleep.

The usage of in_interrupt() in driver code is deprecated as it can not always
detect all states where it is not allowed to sleep.

msleep() has debug code which will trigger a warning if used in bad
context.

Remove in_interrupt().

Cc: Chas Williams <3chas3@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

atm: lanai: dont run lanai_dev_close if not open

[ Upstream commit a2bd45834e83d6c5a04d397bde13d744a4812dfc ]

lanai_dev_open() can fail. When it fail, lanai->base is unmapped and the
pci device is

atm: lanai: dont run lanai_dev_close if not open

[ Upstream commit a2bd45834e83d6c5a04d397bde13d744a4812dfc ]

lanai_dev_open() can fail. When it fail, lanai->base is unmapped and the
pci device is disabled. The caller, lanai_init_one(), then tries to run
atm_dev_deregister(). This will subsequently call lanai_dev_close() and
use the already released MMIO area.

To fix this issue, set the lanai->base to NULL if open fail,
and test the flag in lanai_dev_close().

[ 8.324153] lanai: lanai_start() failed, err=19
[ 8.324819] lanai(itf 0): shutting down interface
[ 8.325211] BUG: unable to handle page fault for address: ffffc90000180024
[ 8.325781] #PF: supervisor write access in kernel mode
[ 8.326215] #PF: error_code(0x0002) - not-present page
[ 8.326641] PGD 100000067 P4D 100000067 PUD 100139067 PMD 10013a067 PTE 0
[ 8.327206] Oops: 0002 [#1] SMP KASAN NOPTI
[ 8.327557] CPU: 0 PID: 95 Comm: modprobe Not tainted 5.11.0-rc7-00090-gdcc0b49040c7 #12
[ 8.328229] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-48-gd9c812dda519-4
[ 8.329145] RIP: 0010:lanai_dev_close+0x4f/0xe5 [lanai]
[ 8.329587] Code: 00 48 c7 c7 00 d3 01 c0 e8 49 4e 0a c2 48 8d bd 08 02 00 00 e8 6e 52 14 c1 48 80
[ 8.330917] RSP: 0018:ffff8881029ef680 EFLAGS: 00010246
[ 8.331196] RAX: 000000000003fffe RBX: ffff888102fb4800 RCX: ffffffffc001a98a
[ 8.331572] RDX: ffffc90000180000 RSI: 0000000000000246 RDI: ffff888102fb4000
[ 8.331948] RBP: ffff888102fb4000 R08: ffffffff8115da8a R09: ffffed102053deaa
[ 8.332326] R10: 0000000000000003 R11: ffffed102053dea9 R12: ffff888102fb48a4
[ 8.332701] R13: ffffffffc00123c0 R14: ffff888102fb4b90 R15: ffff888102fb4b88
[ 8.333077] FS: 00007f08eb9056a0(0000) GS:ffff88815b400000(0000) knlGS:0000000000000000
[ 8.333502] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 8.333806] CR2: ffffc90000180024 CR3: 0000000102a28000 CR4: 00000000000006f0
[ 8.334182] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 8.334557] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 8.334932] Call Trace:
[ 8.335066] atm_dev_deregister+0x161/0x1a0 [atm]
[ 8.335324] lanai_init_one.cold+0x20c/0x96d [lanai]
[ 8.335594] ? lanai_send+0x2a0/0x2a0 [lanai]
[ 8.335831] local_pci_probe+0x6f/0xb0
[ 8.336039] pci_device_probe+0x171/0x240
[ 8.336255] ? pci_device_remove+0xe0/0xe0
[ 8.336475] ? kernfs_create_link+0xb6/0x110
[ 8.336704] ? sysfs_do_create_link_sd.isra.0+0x76/0xe0
[ 8.336983] really_probe+0x161/0x420
[ 8.337181] driver_probe_device+0x6d/0xd0
[ 8.337401] device_driver_attach+0x82/0x90
[ 8.337626] ? device_driver_attach+0x90/0x90
[ 8.337859] __driver_attach+0x60/0x100
[ 8.338065] ? device_driver_attach+0x90/0x90
[ 8.338298] bus_for_each_dev+0xe1/0x140
[ 8.338511] ? subsys_dev_iter_exit+0x10/0x10
[ 8.338745] ? klist_node_init+0x61/0x80
[ 8.338956] bus_add_driver+0x254/0x2a0
[ 8.339164] driver_register+0xd3/0x150
[ 8.339370] ? 0xffffffffc0028000
[ 8.339550] do_one_initcall+0x84/0x250
[ 8.339755] ? trace_event_raw_event_initcall_finish+0x150/0x150
[ 8.340076] ? free_vmap_area_noflush+0x1a5/0x5c0
[ 8.340329] ? unpoison_range+0xf/0x30
[ 8.340532] ? ____kasan_kmalloc.constprop.0+0x84/0xa0
[ 8.340806] ? unpoison_range+0xf/0x30
[ 8.341014] ? unpoison_range+0xf/0x30
[ 8.341217] do_init_module+0xf8/0x350
[ 8.341419] load_module+0x3fe6/0x4340
[ 8.341621] ? vm_unmap_ram+0x1d0/0x1d0
[ 8.341826] ? ____kasan_kmalloc.constprop.0+0x84/0xa0
[ 8.342101] ? module_frob_arch_sections+0x20/0x20
[ 8.342358] ? __do_sys_finit_module+0x108/0x170
[ 8.342604] __do_sys_finit_module+0x108/0x170
[ 8.342841] ? __ia32_sys_init_module+0x40/0x40
[ 8.343083] ? file_open_root+0x200/0x200
[ 8.343298] ? do_sys_open+0x85/0xe0
[ 8.343491] ? filp_open+0x50/0x50
[ 8.343675] ? exit_to_user_mode_prepare+0xfc/0x130
[ 8.343935] do_syscall_64+0x33/0x40
[ 8.344132] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 8.344401] RIP: 0033:0x7f08eb887cf7
[ 8.344594] Code: 48 89 57 30 48 8b 04 24 48 89 47 38 e9 1d a0 02 00 48 89 f8 48 89 f7 48 89 d6 41
[ 8.345565] RSP: 002b:00007ffcd5c98ad8 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
[ 8.345962] RAX: ffffffffffffffda RBX: 00000000008fea70 RCX: 00007f08eb887cf7
[ 8.346336] RDX: 0000000000000000 RSI: 00000000008fd9e0 RDI: 0000000000000003
[ 8.346711] RBP: 0000000000000003 R08: 0000000000000000 R09: 0000000000000001
[ 8.347085] R10: 00007f08eb8eb300 R11: 0000000000000246 R12: 00000000008fd9e0
[ 8.347460] R13: 0000000000000000 R14: 00000000008fddd0 R15: 0000000000000001
[ 8.347836] Modules linked in: lanai(+) atm
[ 8.348065] CR2: ffffc90000180024
[ 8.348244] ---[ end trace 7fdc1c668f2003e5 ]---
[ 8.348490] RIP: 0010:lanai_dev_close+0x4f/0xe5 [lanai]
[ 8.348772] Code: 00 48 c7 c7 00 d3 01 c0 e8 49 4e 0a c2 48 8d bd 08 02 00 00 e8 6e 52 14 c1 48 80
[ 8.349745] RSP: 0018:ffff8881029ef680 EFLAGS: 00010246
[ 8.350022] RAX: 000000000003fffe RBX: ffff888102fb4800 RCX: ffffffffc001a98a
[ 8.350397] RDX: ffffc90000180000 RSI: 0000000000000246 RDI: ffff888102fb4000
[ 8.350772] RBP: ffff888102fb4000 R08: ffffffff8115da8a R09: ffffed102053deaa
[ 8.351151] R10: 0000000000000003 R11: ffffed102053dea9 R12: ffff888102fb48a4
[ 8.351525] R13: ffffffffc00123c0 R14: ffff888102fb4b90 R15: ffff888102fb4b88
[ 8.351918] FS: 00007f08eb9056a0(0000) GS:ffff88815b400000(0000) knlGS:0000000000000000
[ 8.352343] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 8.352647] CR2: ffffc90000180024 CR3: 0000000102a28000 CR4: 00000000000006f0
[ 8.353022] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 8.353397] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 8.353958] modprobe (95) used greatest stack depth: 26216 bytes left

Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

treewide: Use fallthrough pseudo-keyword

Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through mar

treewide: Use fallthrough pseudo-keyword

Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.

[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through

Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>

show more ...

net/atm: remove the atmdev_ops {get, set}sockopt methods

All implementations of these two methods are dummies that always
return -EINVAL.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by

net/atm: remove the atmdev_ops {get, set}sockopt methods

All implementations of these two methods are dummies that always
return -EINVAL.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 152

Based on 1 normalized pattern(s):

this program is free software you can redistribute it and or modify
it under the terms of th

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 152

Based on 1 normalized pattern(s):

this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version

extracted by the scancode license scanner the SPDX license identifier

GPL-2.0-or-later

has been chosen to replace the boilerplate/reference in 3029 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

atm: lanai: use %p to format kernel addresses instead of %x

Don't use %x and casting to print out a kernel address, instead use %p
and remove the casting. Cleans up smatch warnings:

drivers/atm/la

atm: lanai: use %p to format kernel addresses instead of %x

Don't use %x and casting to print out a kernel address, instead use %p
and remove the casting. Cleans up smatch warnings:

drivers/atm/lanai.c:1589 service_buffer_allocate() warn: argument 2 to
%08lX specifier is cast from pointer
drivers/atm/lanai.c:2221 lanai_dev_open() warn: argument 4 to %lx
specifier is cast from pointer

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

treewide: setup_timer() -> timer_setup()

This converts all remaining cases of the old setup_timer() API into using
timer_setup(), where the callback argument is the structure already
holding the str

treewide: setup_timer() -> timer_setup()

This converts all remaining cases of the old setup_timer() API into using
timer_setup(), where the callback argument is the structure already
holding the struct timer_list. These should have no behavioral changes,
since they just change which pointer is passed into the callback with
the same available pointers after conversion. It handles the following
examples, in addition to some other variations.

Casting from unsigned long:

void my_callback(unsigned long data)
{
struct something *ptr = (struct something *)data;
...
}
...
setup_timer(&ptr->my_timer, my_callback, ptr);

and forced object casts:

void my_callback(struct something *ptr)
{
...
}
...
setup_timer(&ptr->my_timer, my_callback, (unsigned long)ptr);

become:

void my_callback(struct timer_list *t)
{
struct something *ptr = from_timer(ptr, t, my_timer);
...
}
...
timer_setup(&ptr->my_timer, my_callback, 0);

Direct function assignments:

void my_callback(unsigned long data)
{
struct something *ptr = (struct something *)data;
...
}
...
ptr->my_timer.function = my_callback;

have a temporary cast added, along with converting the args:

void my_callback(struct timer_list *t)
{
struct something *ptr = from_timer(ptr, t, my_timer);
...
}
...
ptr->my_timer.function = (TIMER_FUNC_TYPE)my_callback;

And finally, callbacks without a data assignment:

void my_callback(unsigned long data)
{
...
}
...
setup_timer(&ptr->my_timer, my_callback, 0);

have their argument renamed to verify they're unused during conversion:

void my_callback(struct timer_list *unused)
{
...
}
...
timer_setup(&ptr->my_timer, my_callback, 0);

The conversion is done with the following Coccinelle script:

spatch --very-quiet --all-includes --include-headers \
-I ./arch/x86/include -I ./arch/x86/include/generated \
-I ./include -I ./arch/x86/include/uapi \
-I ./arch/x86/include/generated/uapi -I ./include/uapi \
-I ./include/generated/uapi --include ./include/linux/kconfig.h \
--dir . \
--cocci-file ~/src/data/timer_setup.cocci

@fix_address_of@
expression e;
@@

setup_timer(
-&(e)
+&e
, ...)

// Update any raw setup_timer() usages that have a NULL callback, but
// would otherwise match change_timer_function_usage, since the latter
// will update all function assignments done in the face of a NULL
// function initialization in setup_timer().
@change_timer_function_usage_NULL@
expression _E;
identifier _timer;
type _cast_data;
@@

(
-setup_timer(&_E->_timer, NULL, _E);
+timer_setup(&_E->_timer, NULL, 0);
|
-setup_timer(&_E->_timer, NULL, (_cast_data)_E);
+timer_setup(&_E->_timer, NULL, 0);
|
-setup_timer(&_E._timer, NULL, &_E);
+timer_setup(&_E._timer, NULL, 0);
|
-setup_timer(&_E._timer, NULL, (_cast_data)&_E);
+timer_setup(&_E._timer, NULL, 0);
)

@change_timer_function_usage@
expression _E;
identifier _timer;
struct timer_list _stl;
identifier _callback;
type _cast_func, _cast_data;
@@

(
-setup_timer(&_E->_timer, _callback, _E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, &_callback, _E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, _callback, (_cast_data)_E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, &_callback, (_cast_data)_E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, (_cast_func)_callback, _E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, (_cast_func)&_callback, _E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, (_cast_func)_callback, (_cast_data)_E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, (_cast_func)&_callback, (_cast_data)_E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E._timer, _callback, (_cast_data)_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, _callback, (_cast_data)&_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, &_callback, (_cast_data)_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, &_callback, (_cast_data)&_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, (_cast_func)_callback, (_cast_data)_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, (_cast_func)_callback, (_cast_data)&_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, (_cast_func)&_callback, (_cast_data)_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, (_cast_func)&_callback, (_cast_data)&_E);
+timer_setup(&_E._timer, _callback, 0);
|
_E->_timer@_stl.function = _callback;
|
_E->_timer@_stl.function = &_callback;
|
_E->_timer@_stl.function = (_cast_func)_callback;
|
_E->_timer@_stl.function = (_cast_func)&_callback;
|
_E._timer@_stl.function = _callback;
|
_E._timer@_stl.function = &_callback;
|
_E._timer@_stl.function = (_cast_func)_callback;
|
_E._timer@_stl.function = (_cast_func)&_callback;
)

// callback(unsigned long arg)
@change_callback_handle_cast
depends on change_timer_function_usage@
identifier change_timer_function_usage._callback;
identifier change_timer_function_usage._timer;
type _origtype;
identifier _origarg;
type _handletype;
identifier _handle;
@@

void _callback(
-_origtype _origarg
+struct timer_list *t
)
{
(
... when != _origarg
_handletype *_handle =
-(_handletype *)_origarg;
+from_timer(_handle, t, _timer);
... when != _origarg
|
... when != _origarg
_handletype *_handle =
-(void *)_origarg;
+from_timer(_handle, t, _timer);
... when != _origarg
|
... when != _origarg
_handletype *_handle;
... when != _handle
_handle =
-(_handletype *)_origarg;
+from_timer(_handle, t, _timer);
... when != _origarg
|
... when != _origarg
_handletype *_handle;
... when != _handle
_handle =
-(void *)_origarg;
+from_timer(_handle, t, _timer);
... when != _origarg
)
}

// callback(unsigned long arg) without existing variable
@change_callback_handle_cast_no_arg
depends on change_timer_function_usage &&
!change_callback_handle_cast@
identifier change_timer_function_usage._callback;
identifier change_timer_function_usage._timer;
type _origtype;
identifier _origarg;
type _handletype;
@@

void _callback(
-_origtype _origarg
+struct timer_list *t
)
{
+ _handletype *_origarg = from_timer(_origarg, t, _timer);
+
... when != _origarg
- (_handletype *)_origarg
+ _origarg
... when != _origarg
}

// Avoid already converted callbacks.
@match_callback_converted
depends on change_timer_function_usage &&
!change_callback_handle_cast &&
!change_callback_handle_cast_no_arg@
identifier change_timer_function_usage._callback;
identifier t;
@@

void _callback(struct timer_list *t)
{ ... }

// callback(struct something *handle)
@change_callback_handle_arg
depends on change_timer_function_usage &&
!match_callback_converted &&
!change_callback_handle_cast &&
!change_callback_handle_cast_no_arg@
identifier change_timer_function_usage._callback;
identifier change_timer_function_usage._timer;
type _handletype;
identifier _handle;
@@

void _callback(
-_handletype *_handle
+struct timer_list *t
)
{
+ _handletype *_handle = from_timer(_handle, t, _timer);
...
}

// If change_callback_handle_arg ran on an empty function, remove
// the added handler.
@unchange_callback_handle_arg
depends on change_timer_function_usage &&
change_callback_handle_arg@
identifier change_timer_function_usage._callback;
identifier change_timer_function_usage._timer;
type _handletype;
identifier _handle;
identifier t;
@@

void _callback(struct timer_list *t)
{
- _handletype *_handle = from_timer(_handle, t, _timer);
}

// We only want to refactor the setup_timer() data argument if we've found
// the matching callback. This undoes changes in change_timer_function_usage.
@unchange_timer_function_usage
depends on change_timer_function_usage &&
!change_callback_handle_cast &&
!change_callback_handle_cast_no_arg &&
!change_callback_handle_arg@
expression change_timer_function_usage._E;
identifier change_timer_function_usage._timer;
identifier change_timer_function_usage._callback;
type change_timer_function_usage._cast_data;
@@

(
-timer_setup(&_E->_timer, _callback, 0);
+setup_timer(&_E->_timer, _callback, (_cast_data)_E);
|
-timer_setup(&_E._timer, _callback, 0);
+setup_timer(&_E._timer, _callback, (_cast_data)&_E);
)

// If we fixed a callback from a .function assignment, fix the
// assignment cast now.
@change_timer_function_assignment
depends on change_timer_function_usage &&
(change_callback_handle_cast ||
change_callback_handle_cast_no_arg ||
change_callback_handle_arg)@
expression change_timer_function_usage._E;
identifier change_timer_function_usage._timer;
identifier change_timer_function_usage._callback;
type _cast_func;
typedef TIMER_FUNC_TYPE;
@@

(
_E->_timer.function =
-_callback
+(TIMER_FUNC_TYPE)_callback
;
|
_E->_timer.function =
-&_callback
+(TIMER_FUNC_TYPE)_callback
;
|
_E->_timer.function =
-(_cast_func)_callback;
+(TIMER_FUNC_TYPE)_callback
;
|
_E->_timer.function =
-(_cast_func)&_callback
+(TIMER_FUNC_TYPE)_callback
;
|
_E._timer.function =
-_callback
+(TIMER_FUNC_TYPE)_callback
;
|
_E._timer.function =
-&_callback;
+(TIMER_FUNC_TYPE)_callback
;
|
_E._timer.function =
-(_cast_func)_callback
+(TIMER_FUNC_TYPE)_callback
;
|
_E._timer.function =
-(_cast_func)&_callback
+(TIMER_FUNC_TYPE)_callback
;
)

// Sometimes timer functions are called directly. Replace matched args.
@change_timer_function_calls
depends on change_timer_function_usage &&
(change_callback_handle_cast ||
change_callback_handle_cast_no_arg ||
change_callback_handle_arg)@
expression _E;
identifier change_timer_function_usage._timer;
identifier change_timer_function_usage._callback;
type _cast_data;
@@

_callback(
(
-(_cast_data)_E
+&_E->_timer
|
-(_cast_data)&_E
+&_E._timer
|
-_E
+&_E->_timer
)
)

// If a timer has been configured without a data argument, it can be
// converted without regard to the callback argument, since it is unused.
@match_timer_function_unused_data@
expression _E;
identifier _timer;
identifier _callback;
@@

(
-setup_timer(&_E->_timer, _callback, 0);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, _callback, 0L);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, _callback, 0UL);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E._timer, _callback, 0);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, _callback, 0L);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, _callback, 0UL);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_timer, _callback, 0);
+timer_setup(&_timer, _callback, 0);
|
-setup_timer(&_timer, _callback, 0L);
+timer_setup(&_timer, _callback, 0);
|
-setup_timer(&_timer, _callback, 0UL);
+timer_setup(&_timer, _callback, 0);
|
-setup_timer(_timer, _callback, 0);
+timer_setup(_timer, _callback, 0);
|
-setup_timer(_timer, _callback, 0L);
+timer_setup(_timer, _callback, 0);
|
-setup_timer(_timer, _callback, 0UL);
+timer_setup(_timer, _callback, 0);
)

@change_callback_unused_data
depends on match_timer_function_unused_data@
identifier match_timer_function_unused_data._callback;
type _origtype;
identifier _origarg;
@@

void _callback(
-_origtype _origarg
+struct timer_list *unused
)
{
... when != _origarg
}

Signed-off-by: Kees Cook <keescook@chromium.org>

show more ...

treewide: init_timer() -> setup_timer()

This mechanically converts all remaining cases of ancient open-coded timer
setup with the old setup_timer() API, which is the first step in timer
conversions.

treewide: init_timer() -> setup_timer()

This mechanically converts all remaining cases of ancient open-coded timer
setup with the old setup_timer() API, which is the first step in timer
conversions. This has no behavioral changes, since it ultimately just
changes the order of assignment to fields of struct timer_list when
finding variations of:

init_timer(&t);
f.function = timer_callback;
t.data = timer_callback_arg;

to be converted into:

setup_timer(&t, timer_callback, timer_callback_arg);

The conversion is done with the following Coccinelle script, which
is an improved version of scripts/cocci/api/setup_timer.cocci, in the
following ways:
- assignments-before-init_timer() cases
- limit the .data case removal to the specific struct timer_list instance
- handling calls by dereference (timer->field vs timer.field)

spatch --very-quiet --all-includes --include-headers \
-I ./arch/x86/include -I ./arch/x86/include/generated \
-I ./include -I ./arch/x86/include/uapi \
-I ./arch/x86/include/generated/uapi -I ./include/uapi \
-I ./include/generated/uapi --include ./include/linux/kconfig.h \
--dir . \
--cocci-file ~/src/data/setup_timer.cocci

@fix_address_of@
expression e;
@@

init_timer(
-&(e)
+&e
, ...)

// Match the common cases first to avoid Coccinelle parsing loops with
// "... when" clauses.

@match_immediate_function_data_after_init_timer@
expression e, func, da;
@@

-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);
(
-\(e.function\|e->function\) = func;
-\(e.data\|e->data\) = da;
|
-\(e.data\|e->data\) = da;
-\(e.function\|e->function\) = func;
)

@match_immediate_function_data_before_init_timer@
expression e, func, da;
@@

(
-\(e.function\|e->function\) = func;
-\(e.data\|e->data\) = da;
|
-\(e.data\|e->data\) = da;
-\(e.function\|e->function\) = func;
)
-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);

@match_function_and_data_after_init_timer@
expression e, e2, e3, e4, e5, func, da;
@@

-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);
... when != func = e2
when != da = e3
(
-e.function = func;
... when != da = e4
-e.data = da;
|
-e->function = func;
... when != da = e4
-e->data = da;
|
-e.data = da;
... when != func = e5
-e.function = func;
|
-e->data = da;
... when != func = e5
-e->function = func;
)

@match_function_and_data_before_init_timer@
expression e, e2, e3, e4, e5, func, da;
@@
(
-e.function = func;
... when != da = e4
-e.data = da;
|
-e->function = func;
... when != da = e4
-e->data = da;
|
-e.data = da;
... when != func = e5
-e.function = func;
|
-e->data = da;
... when != func = e5
-e->function = func;
)
... when != func = e2
when != da = e3
-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);

@r1 exists@
expression t;
identifier f;
position p;
@@

f(...) { ... when any
init_timer@p(\(&t\|t\))
... when any
}

@r2 exists@
expression r1.t;
identifier g != r1.f;
expression e8;
@@

g(...) { ... when any
\(t.data\|t->data\) = e8
... when any
}

// It is dangerous to use setup_timer if data field is initialized
// in another function.
@script:python depends on r2@
p << r1.p;
@@

cocci.include_match(False)

@r3@
expression r1.t, func, e7;
position r1.p;
@@

(
-init_timer@p(&t);
+setup_timer(&t, func, 0UL);
... when != func = e7
-t.function = func;
|
-t.function = func;
... when != func = e7
-init_timer@p(&t);
+setup_timer(&t, func, 0UL);
|
-init_timer@p(t);
+setup_timer(t, func, 0UL);
... when != func = e7
-t->function = func;
|
-t->function = func;
... when != func = e7
-init_timer@p(t);
+setup_timer(t, func, 0UL);
)

Signed-off-by: Kees Cook <keescook@chromium.org>

show more ...

atm: lanai: constify pci_device_id.

pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the

atm: lanai: constify pci_device_id.

pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.

File size before:
text data bss dec hex filename
18074 352 0 18426 47fa drivers/atm/lanai.o

File size After adding 'const':
text data bss dec hex filename
18170 256 0 18426 47fa drivers/atm/lanai.o

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

lib/vsprintf.c: remove %Z support

Now that %z is standartised in C99 there is no reason to support %Z.
Unlike %L it doesn't even make format strings smaller.

Use BUILD_BUG_ON in a couple ATM driver

lib/vsprintf.c: remove %Z support

Now that %z is standartised in C99 there is no reason to support %Z.
Unlike %L it doesn't even make format strings smaller.

Use BUILD_BUG_ON in a couple ATM drivers.

In case anyone didn't notice lib/vsprintf.o is about half of SLUB which
is in my opinion is quite an achievement. Hopefully this patch inspires
someone else to trim vsprintf.c more.

Link: http://lkml.kernel.org/r/20170103230126.GA30170@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

show more ...

atm: lanai: set error code when ioremap fails

In function lanai_dev_open(), when the call to ioremap() fails, the
value of return variable result is 0. 0 means no error in this context.
This patch f

atm: lanai: set error code when ioremap fails

In function lanai_dev_open(), when the call to ioremap() fails, the
value of return variable result is 0. 0 means no error in this context.
This patch fixes the bug, assigning "-ENOMEM" to result when ioremap()
returns a NULL pointer.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188791

Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

atm: remove deprecated use of pci api

Signed-off-by: Chas Williams - CONTRACTOR <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>

atm: lanai: Remove unused function

Remove the function aal5_spacefor() that is not used anywhere.

This was partially found by using a static code analysis program called cppcheck.

Signed-off-by: R

atm: lanai: Remove unused function

Remove the function aal5_spacefor() that is not used anywhere.

This was partially found by using a static code analysis program called cppcheck.

Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

atm: simplify lanai.c by using module_pci_driver

This simplifies the lanai.c driver by using
the module_pci_driver() macro, at the expense
of losing only debugging messages.

Signed-off-by: Michael

atm: simplify lanai.c by using module_pci_driver

This simplifies the lanai.c driver by using
the module_pci_driver() macro, at the expense
of losing only debugging messages.

Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

Drivers: atm: remove __dev* attributes.

CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.

This change removes the use of __devinit, __devexit_p, __dev

Drivers: atm: remove __dev* attributes.

CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.

This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.

Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.

Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

atm: Fix typo in lanai.c

Correct spelling "reseting" to resetting" in
drivers/atm/lanai.c

Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

atm: Convert vmalloc/memset to vzalloc

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

lanai: use pci_dev->subsystem_device

The driver reads PCI subsystem IDs from the PCI configuration registers while
it is already stored by the PCI subsystem in the 'subsystem_device' field of
'struc

lanai: use pci_dev->subsystem_device

The driver reads PCI subsystem IDs from the PCI configuration registers while
it is already stored by the PCI subsystem in the 'subsystem_device' field of
'struct pci_dev'...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

Fix common misspellings

Fixes generated by 'codespell' and manually reviewed.

Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>

atm: correct sysfs 'device' link creation and parent relationships

The ATM subsystem was incorrectly creating the 'device' link for ATM
nodes in sysfs. This led to incorrect device/parent relations

atm: correct sysfs 'device' link creation and parent relationships

The ATM subsystem was incorrectly creating the 'device' link for ATM
nodes in sysfs. This led to incorrect device/parent relationships
exposed by sysfs and udev. Instead of rolling the 'device' link by hand
in the generic ATM code, pass each ATM driver's bus device down to the
sysfs code and let sysfs do this stuff correctly.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

atm: lanai: use kernel's '%pM' format option to print MAC

Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Chas Williams <chas@cmf.nrl.navy.mil>
Cc: linux-atm-general@lists.sourceforge

atm: lanai: use kernel's '%pM' format option to print MAC

Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Chas Williams <chas@cmf.nrl.navy.mil>
Cc: linux-atm-general@lists.sourceforge.net
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h

percpu.h is included by sched.h and module.h and thus ends up being
included when bu

include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h

percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.

2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).

* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.

Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>

show more ...

atm: use for_each_set_bit()

Replace open-coded loop with for_each_set_bit().

Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: Andrew Mor

atm: use for_each_set_bit()

Replace open-coded loop with for_each_set_bit().

Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

drivers/atm/lanai.c: use %pM to show MAC address

Use the %pM kernel extension to display the MAC address.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David S. Miller <davem@

drivers/atm/lanai.c: use %pM to show MAC address

Use the %pM kernel extension to display the MAC address.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...