1 /* 2 * Copyright (C) Freescale Semiconductor, Inc. 2006. 3 * Author: Jason Jin<Jason.jin@freescale.com> 4 * Zhang Wei<wei.zhang@freescale.com> 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 #ifndef _AHCI_H_ 9 #define _AHCI_H_ 10 11 #include <pci.h> 12 13 #define AHCI_PCI_BAR 0x24 14 #define AHCI_MAX_SG 56 /* hardware max is 64K */ 15 #define AHCI_CMD_SLOT_SZ 32 16 #define AHCI_MAX_CMD_SLOT 32 17 #define AHCI_RX_FIS_SZ 256 18 #define AHCI_CMD_TBL_HDR 0x80 19 #define AHCI_CMD_TBL_CDB 0x40 20 #define AHCI_CMD_TBL_SZ AHCI_CMD_TBL_HDR + (AHCI_MAX_SG * 16) 21 #define AHCI_PORT_PRIV_DMA_SZ (AHCI_CMD_SLOT_SZ * AHCI_MAX_CMD_SLOT + \ 22 AHCI_CMD_TBL_SZ + AHCI_RX_FIS_SZ) 23 #define AHCI_CMD_ATAPI (1 << 5) 24 #define AHCI_CMD_WRITE (1 << 6) 25 #define AHCI_CMD_PREFETCH (1 << 7) 26 #define AHCI_CMD_RESET (1 << 8) 27 #define AHCI_CMD_CLR_BUSY (1 << 10) 28 29 #define RX_FIS_D2H_REG 0x40 /* offset of D2H Register FIS data */ 30 31 /* Global controller registers */ 32 #define HOST_CAP 0x00 /* host capabilities */ 33 #define HOST_CTL 0x04 /* global host control */ 34 #define HOST_IRQ_STAT 0x08 /* interrupt status */ 35 #define HOST_PORTS_IMPL 0x0c /* bitmap of implemented ports */ 36 #define HOST_VERSION 0x10 /* AHCI spec. version compliancy */ 37 #define HOST_CAP2 0x24 /* host capabilities, extended */ 38 39 /* HOST_CTL bits */ 40 #define HOST_RESET (1 << 0) /* reset controller; self-clear */ 41 #define HOST_IRQ_EN (1 << 1) /* global IRQ enable */ 42 #define HOST_AHCI_EN (1 << 31) /* AHCI enabled */ 43 44 /* Registers for each SATA port */ 45 #define PORT_LST_ADDR 0x00 /* command list DMA addr */ 46 #define PORT_LST_ADDR_HI 0x04 /* command list DMA addr hi */ 47 #define PORT_FIS_ADDR 0x08 /* FIS rx buf addr */ 48 #define PORT_FIS_ADDR_HI 0x0c /* FIS rx buf addr hi */ 49 #define PORT_IRQ_STAT 0x10 /* interrupt status */ 50 #define PORT_IRQ_MASK 0x14 /* interrupt enable/disable mask */ 51 #define PORT_CMD 0x18 /* port command */ 52 #define PORT_TFDATA 0x20 /* taskfile data */ 53 #define PORT_SIG 0x24 /* device TF signature */ 54 #define PORT_CMD_ISSUE 0x38 /* command issue */ 55 #define PORT_SCR 0x28 /* SATA phy register block */ 56 #define PORT_SCR_STAT 0x28 /* SATA phy register: SStatus */ 57 #define PORT_SCR_CTL 0x2c /* SATA phy register: SControl */ 58 #define PORT_SCR_ERR 0x30 /* SATA phy register: SError */ 59 #define PORT_SCR_ACT 0x34 /* SATA phy register: SActive */ 60 61 #ifdef CONFIG_SUNXI_AHCI 62 #define PORT_P0DMACR 0x70 /* SUNXI specific "DMA register" */ 63 #endif 64 65 /* PORT_IRQ_{STAT,MASK} bits */ 66 #define PORT_IRQ_COLD_PRES (1 << 31) /* cold presence detect */ 67 #define PORT_IRQ_TF_ERR (1 << 30) /* task file error */ 68 #define PORT_IRQ_HBUS_ERR (1 << 29) /* host bus fatal error */ 69 #define PORT_IRQ_HBUS_DATA_ERR (1 << 28) /* host bus data error */ 70 #define PORT_IRQ_IF_ERR (1 << 27) /* interface fatal error */ 71 #define PORT_IRQ_IF_NONFATAL (1 << 26) /* interface non-fatal error */ 72 #define PORT_IRQ_OVERFLOW (1 << 24) /* xfer exhausted available S/G */ 73 #define PORT_IRQ_BAD_PMP (1 << 23) /* incorrect port multiplier */ 74 75 #define PORT_IRQ_PHYRDY (1 << 22) /* PhyRdy changed */ 76 #define PORT_IRQ_DEV_ILCK (1 << 7) /* device interlock */ 77 #define PORT_IRQ_CONNECT (1 << 6) /* port connect change status */ 78 #define PORT_IRQ_SG_DONE (1 << 5) /* descriptor processed */ 79 #define PORT_IRQ_UNK_FIS (1 << 4) /* unknown FIS rx'd */ 80 #define PORT_IRQ_SDB_FIS (1 << 3) /* Set Device Bits FIS rx'd */ 81 #define PORT_IRQ_DMAS_FIS (1 << 2) /* DMA Setup FIS rx'd */ 82 #define PORT_IRQ_PIOS_FIS (1 << 1) /* PIO Setup FIS rx'd */ 83 #define PORT_IRQ_D2H_REG_FIS (1 << 0) /* D2H Register FIS rx'd */ 84 85 #define PORT_IRQ_FATAL PORT_IRQ_TF_ERR | PORT_IRQ_HBUS_ERR \ 86 | PORT_IRQ_HBUS_DATA_ERR | PORT_IRQ_IF_ERR 87 88 #define DEF_PORT_IRQ PORT_IRQ_FATAL | PORT_IRQ_PHYRDY \ 89 | PORT_IRQ_CONNECT | PORT_IRQ_SG_DONE \ 90 | PORT_IRQ_UNK_FIS | PORT_IRQ_SDB_FIS \ 91 | PORT_IRQ_DMAS_FIS | PORT_IRQ_PIOS_FIS \ 92 | PORT_IRQ_D2H_REG_FIS 93 94 /* PORT_SCR_STAT bits */ 95 #define PORT_SCR_STAT_DET_MASK 0x3 96 #define PORT_SCR_STAT_DET_COMINIT 0x1 97 #define PORT_SCR_STAT_DET_PHYRDY 0x3 98 99 /* PORT_CMD bits */ 100 #define PORT_CMD_ATAPI (1 << 24) /* Device is ATAPI */ 101 #define PORT_CMD_LIST_ON (1 << 15) /* cmd list DMA engine running */ 102 #define PORT_CMD_FIS_ON (1 << 14) /* FIS DMA engine running */ 103 #define PORT_CMD_FIS_RX (1 << 4) /* Enable FIS receive DMA engine */ 104 #define PORT_CMD_CLO (1 << 3) /* Command list override */ 105 #define PORT_CMD_POWER_ON (1 << 2) /* Power up device */ 106 #define PORT_CMD_SPIN_UP (1 << 1) /* Spin up device */ 107 #define PORT_CMD_START (1 << 0) /* Enable port DMA engine */ 108 109 #define PORT_CMD_ICC_ACTIVE (0x1 << 28) /* Put i/f in active state */ 110 #define PORT_CMD_ICC_PARTIAL (0x2 << 28) /* Put i/f in partial state */ 111 #define PORT_CMD_ICC_SLUMBER (0x6 << 28) /* Put i/f in slumber state */ 112 113 #define AHCI_MAX_PORTS 32 114 115 #define ATA_FLAG_SATA (1 << 3) 116 #define ATA_FLAG_NO_LEGACY (1 << 4) /* no legacy mode check */ 117 #define ATA_FLAG_MMIO (1 << 6) /* use MMIO, not PIO */ 118 #define ATA_FLAG_SATA_RESET (1 << 7) /* (obsolete) use COMRESET */ 119 #define ATA_FLAG_PIO_DMA (1 << 8) /* PIO cmds via DMA */ 120 #define ATA_FLAG_NO_ATAPI (1 << 11) /* No ATAPI support */ 121 122 struct ahci_cmd_hdr { 123 u32 opts; 124 u32 status; 125 u32 tbl_addr; 126 u32 tbl_addr_hi; 127 u32 reserved[4]; 128 }; 129 130 struct ahci_sg { 131 u32 addr; 132 u32 addr_hi; 133 u32 reserved; 134 u32 flags_size; 135 }; 136 137 struct ahci_ioports { 138 void __iomem *cmd_addr; 139 void __iomem *scr_addr; 140 void __iomem *port_mmio; 141 struct ahci_cmd_hdr *cmd_slot; 142 struct ahci_sg *cmd_tbl_sg; 143 ulong cmd_tbl; 144 u32 rx_fis; 145 }; 146 147 /** 148 * struct ahci_uc_priv - information about an AHCI controller 149 * 150 * When driver model is used, this is accessible using dev_get_uclass_priv(dev) 151 * where dev is the controller (although at present it sometimes stands alone). 152 */ 153 struct ahci_uc_priv { 154 #if defined(CONFIG_DM_PCI) || defined(CONFIG_DM_SCSI) 155 /* 156 * TODO(sjg@chromium.org): Drop this once this structure is only used 157 * in a driver-model context (i.e. attached to a device with 158 * dev_get_uclass_priv() 159 */ 160 struct udevice *dev; 161 #else 162 pci_dev_t dev; 163 #endif 164 struct ahci_ioports port[AHCI_MAX_PORTS]; 165 u16 *ataid[AHCI_MAX_PORTS]; 166 u32 n_ports; 167 u32 hard_port_no; 168 u32 host_flags; 169 u32 host_set_flags; 170 void __iomem *mmio_base; 171 u32 pio_mask; 172 u32 udma_mask; 173 u32 flags; 174 u32 cap; /* cache of HOST_CAP register */ 175 u32 port_map; /* cache of HOST_PORTS_IMPL reg */ 176 u32 link_port_map; /*linkup port map*/ 177 }; 178 179 struct ahci_ops { 180 /** 181 * reset() - reset the controller 182 * 183 * @dev: Controller to reset 184 * @return 0 if OK, -ve on error 185 */ 186 int (*reset)(struct udevice *dev); 187 188 /** 189 * port_status() - get the status of a SATA port 190 * 191 * @dev: Controller to reset 192 * @port: Port number to check (0 for first) 193 * @return 0 if detected, -ENXIO if nothing on port, other -ve on error 194 */ 195 int (*port_status)(struct udevice *dev, int port); 196 197 /** 198 * scan() - scan SATA ports 199 * 200 * @dev: Controller to scan 201 * @return 0 if OK, -ve on error 202 */ 203 int (*scan)(struct udevice *dev); 204 }; 205 206 #define ahci_get_ops(dev) ((struct ahci_ops *)(dev)->driver->ops) 207 208 /** 209 * sata_reset() - reset the controller 210 * 211 * @dev: Controller to reset 212 * @return 0 if OK, -ve on error 213 */ 214 int sata_reset(struct udevice *dev); 215 216 /** 217 * sata_port_status() - get the status of a SATA port 218 * 219 * @dev: Controller to reset 220 * @port: Port number to check (0 for first) 221 * @return 0 if detected, -ENXIO if nothin on port, other -ve on error 222 */ 223 int sata_dm_port_status(struct udevice *dev, int port); 224 225 /** 226 * sata_scan() - scan SATA ports 227 * 228 * @dev: Controller to scan 229 * @return 0 if OK, -ve on error 230 */ 231 int sata_scan(struct udevice *dev); 232 233 int ahci_init(void __iomem *base); 234 int ahci_reset(void __iomem *base); 235 236 /** 237 * ahci_init_one_dm() - set up a single AHCI port 238 * 239 * @dev: Controller to init 240 */ 241 int ahci_init_one_dm(struct udevice *dev); 242 243 /** 244 * ahci_start_ports_dm() - start all AHCI ports for a controller 245 * 246 * @dev: Controller containing ports to start 247 */ 248 int ahci_start_ports_dm(struct udevice *dev); 249 250 /** 251 * ahci_init_dm() - init AHCI for a controller, finding all ports 252 * 253 * @dev: Device to init 254 */ 255 int ahci_init_dm(struct udevice *dev, void __iomem *base); 256 257 /** 258 * ahci_bind_scsi() - bind a new SCSI bus as a child 259 * 260 * Note that the SCSI bus device will itself bind block devices 261 * 262 * @ahci_dev: AHCI parent device 263 * @devp: Returns new SCSI bus device 264 * @return 0 if OK, -ve on error 265 */ 266 int ahci_bind_scsi(struct udevice *ahci_dev, struct udevice **devp); 267 268 /** 269 * ahci_probe_scsi() - probe and scan the attached SCSI bus 270 * 271 * Note that the SCSI device will itself bind block devices for any storage 272 * devices it finds. 273 * 274 * @ahci_dev: AHCI parent device 275 * @base: Base address of AHCI port 276 * @return 0 if OK, -ve on error 277 */ 278 int ahci_probe_scsi(struct udevice *ahci_dev, ulong base); 279 280 /** 281 * ahci_probe_scsi_pci() - probe and scan the attached SCSI bus on PCI 282 * 283 * Note that the SCSI device will itself bind block devices for any storage 284 * devices it finds. 285 * 286 * @ahci_dev: AHCI parent device 287 * @return 0 if OK, -ve on error 288 */ 289 int ahci_probe_scsi_pci(struct udevice *ahci_dev); 290 291 #endif 292