xref: /openbmc/u-boot/drivers/spi/Kconfig (revision bf9012b8) 
1menu "SPI Support"
2
3config DM_SPI
4	bool "Enable Driver Model for SPI drivers"
5	depends on DM
6	help
7	  Enable driver model for SPI. The SPI slave interface
8	  (spi_setup_slave(), spi_xfer(), etc.) is then implemented by
9	  the SPI uclass. Drivers provide methods to access the SPI
10	  buses that they control. The uclass interface is defined in
11	  include/spi.h. The existing spi_slave structure is attached
12	  as 'parent data' to every slave on each bus. Slaves
13	  typically use driver-private data instead of extending the
14	  spi_slave structure.
15
16if DM_SPI
17
18config ALTERA_SPI
19	bool "Altera SPI driver"
20	help
21	  Enable the Altera SPI driver. This driver can be used to
22	  access the SPI NOR flash on platforms embedding this Altera
23	  IP core. Please find details on the "Embedded Peripherals IP
24	  User Guide" of Altera.
25
26config ATH79_SPI
27	bool "Atheros SPI driver"
28	depends on ARCH_ATH79
29	help
30	  Enable the Atheros ar7xxx/ar9xxx SoC SPI driver, it was used
31	  to access SPI NOR flash and other SPI peripherals. This driver
32	  uses driver model and requires a device tree binding to operate.
33	  please refer to doc/device-tree-bindings/spi/spi-ath79.txt.
34
35config ATMEL_SPI
36	bool "Atmel SPI driver"
37	depends on ARCH_AT91
38	help
39	  This enables driver for the Atmel SPI Controller, present on
40	  many AT32 (AVR32) and AT91 (ARM) chips. This driver can be
41	  used to access the SPI Flash, such as AT25DF321.
42
43config CADENCE_QSPI
44	bool "Cadence QSPI driver"
45	help
46	  Enable the Cadence Quad-SPI (QSPI) driver. This driver can be
47	  used to access the SPI NOR flash on platforms embedding this
48	  Cadence IP core.
49
50config DESIGNWARE_SPI
51	bool "Designware SPI driver"
52	help
53	  Enable the Designware SPI driver. This driver can be used to
54	  access the SPI NOR flash on platforms embedding this Designware
55	  IP core.
56
57config EXYNOS_SPI
58	bool "Samsung Exynos SPI driver"
59	help
60	  Enable the Samsung Exynos SPI driver. This driver can be used to
61	  access the SPI NOR flash on platforms embedding this Samsung
62	  Exynos IP core.
63
64config FSL_DSPI
65	bool "Freescale DSPI driver"
66	help
67	  Enable the Freescale DSPI driver. This driver can be used to
68	  access the SPI NOR flash and SPI Data flash on platforms embedding
69	  this Freescale DSPI IP core. LS102xA and Colibri VF50/VF61 platforms
70	  use this driver.
71
72config ICH_SPI
73	bool "Intel ICH SPI driver"
74	help
75	  Enable the Intel ICH SPI driver. This driver can be used to
76	  access the SPI NOR flash on platforms embedding this Intel
77	  ICH IP core.
78
79config MVEBU_A3700_SPI
80	bool "Marvell Armada 3700 SPI driver"
81	help
82	  Enable the Marvell Armada 3700 SPI driver. This driver can be
83	  used to access the SPI NOR flash on platforms embedding this
84	  Marvell IP core.
85
86config PIC32_SPI
87	bool "Microchip PIC32 SPI driver"
88	depends on MACH_PIC32
89	help
90	  Enable the Microchip PIC32 SPI driver. This driver can be used
91	  to access the SPI NOR flash, MMC-over-SPI on platforms based on
92	  Microchip PIC32 family devices.
93
94config ROCKCHIP_SPI
95	bool "Rockchip SPI driver"
96	help
97	  Enable the Rockchip SPI driver, used to access SPI NOR flash and
98	  other SPI peripherals (such as the Chrome OS EC) on Rockchip SoCs.
99	  This uses driver model and requires a device tree binding to
100	  operate.
101
102config SANDBOX_SPI
103	bool "Sandbox SPI driver"
104	depends on SANDBOX && DM
105	help
106	  Enable SPI support for sandbox. This is an emulation of a real SPI
107	  bus. Devices can be attached to the bus using the device tree
108	  which specifies the driver to use. As an example, see this device
109	  tree fragment from sandbox.dts. It shows that the SPI bus has a
110	  single flash device on chip select 0 which is emulated by the driver
111	  for "sandbox,spi-flash", which is in drivers/mtd/spi/sandbox.c.
112
113	  spi@0 {
114		#address-cells = <1>;
115		#size-cells = <0>;
116		reg = <0>;
117		compatible = "sandbox,spi";
118		cs-gpios = <0>, <&gpio_a 0>;
119		flash@0 {
120			reg = <0>;
121			compatible = "spansion,m25p16", "sandbox,spi-flash";
122			spi-max-frequency = <40000000>;
123			sandbox,filename = "spi.bin";
124		};
125	  };
126
127config STM32_QSPI
128	bool "STM32F7 QSPI driver"
129	depends on STM32F7
130	help
131	  Enable the STM32F7 Quad-SPI (QSPI) driver. This driver can be
132	  used to access the SPI NOR flash chips on platforms embedding
133	  this ST IP core.
134
135config TEGRA114_SPI
136	bool "nVidia Tegra114 SPI driver"
137	help
138	  Enable the nVidia Tegra114 SPI driver. This driver can be used to
139	  access the SPI NOR flash on platforms embedding this nVidia Tegra114
140	  IP core.
141
142	  This controller is different than the older SoCs SPI controller and
143	  also register interface get changed with this controller.
144
145config TEGRA20_SFLASH
146	bool "nVidia Tegra20 Serial Flash controller driver"
147	help
148	  Enable the nVidia Tegra20 Serial Flash controller driver. This driver
149	  can be used to access the SPI NOR flash on platforms embedding this
150	  nVidia Tegra20 IP core.
151
152config TEGRA20_SLINK
153	bool "nVidia Tegra20/Tegra30 SLINK driver"
154	help
155	  Enable the nVidia Tegra20/Tegra30 SLINK driver. This driver can
156	  be used to access the SPI NOR flash on platforms embedding this
157	  nVidia Tegra20/Tegra30 IP cores.
158
159config TEGRA210_QSPI
160	bool "nVidia Tegra210 QSPI driver"
161	help
162	  Enable the Tegra Quad-SPI (QSPI) driver for T210. This driver
163	  be used to access SPI chips on platforms embedding this
164	  NVIDIA Tegra210 IP core.
165
166config XILINX_SPI
167	bool "Xilinx SPI driver"
168	help
169	  Enable the Xilinx SPI driver from the Xilinx EDK. This SPI
170	  controller support 8 bit SPI transfers only, with or w/o FIFO.
171	  For more info on Xilinx SPI Register Definitions and Overview
172	  see driver file - drivers/spi/xilinx_spi.c
173
174config ZYNQ_SPI
175	bool "Zynq SPI driver"
176	depends on ARCH_ZYNQ || ARCH_ZYNQMP
177	help
178	  Enable the Zynq SPI driver. This driver can be used to
179	  access the SPI NOR flash on platforms embedding this Zynq
180	  SPI IP core.
181
182config ZYNQ_QSPI
183	bool "Zynq QSPI driver"
184	depends on ARCH_ZYNQ
185	help
186	  Enable the Zynq Quad-SPI (QSPI) driver. This driver can be
187	  used to access the SPI NOR flash on platforms embedding this
188	  Zynq QSPI IP core. This IP is used to connect the flash in
189	  4-bit qspi, 8-bit dual stacked and shared 4-bit dual parallel.
190
191config OMAP3_SPI
192	bool "McSPI driver for OMAP"
193	help
194	  SPI master controller for OMAP24XX and later Multichannel SPI
195	  (McSPI). This driver be used to access SPI chips on platforms
196	  embedding this OMAP3 McSPI IP core.
197
198endif # if DM_SPI
199
200config SOFT_SPI
201	bool "Soft SPI driver"
202	help
203	 Enable Soft SPI driver. This driver is to use GPIO simulate
204	 the SPI protocol.
205
206config FSL_ESPI
207	bool "Freescale eSPI driver"
208	help
209	  Enable the Freescale eSPI driver. This driver can be used to
210	  access the SPI interface and SPI NOR flash on platforms embedding
211	  this Freescale eSPI IP core.
212
213config FSL_QSPI
214	bool "Freescale QSPI driver"
215	help
216	  Enable the Freescale Quad-SPI (QSPI) driver. This driver can be
217	  used to access the SPI NOR flash on platforms embedding this
218	  Freescale IP core.
219
220config TI_QSPI
221	bool "TI QSPI driver"
222	help
223	  Enable the TI Quad-SPI (QSPI) driver for DRA7xx and AM43xx evms.
224	  This driver support spi flash single, quad and memory reads.
225
226endmenu # menu "SPI Support"
227