1 2config BITBANGMII 3 bool "Bit-banged ethernet MII management channel support" 4 5config MV88E6352_SWITCH 6 bool "Marvell 88E6352 switch support" 7 8menuconfig PHYLIB 9 bool "Ethernet PHY (physical media interface) support" 10 help 11 Enable Ethernet PHY (physical media interface) support. 12 13if PHYLIB 14 15config B53_SWITCH 16 bool "Broadcom BCM53xx (RoboSwitch) Ethernet switch PHY support." 17 help 18 Enable support for Broadcom BCM53xx (RoboSwitch) Ethernet switches. 19 This currently supports BCM53125 and similar models. 20 21if B53_SWITCH 22 23config B53_CPU_PORT 24 int "CPU port" 25 default 8 26 27config B53_PHY_PORTS 28 hex "Bitmask of PHY ports" 29 30endif # B53_SWITCH 31 32config MV88E61XX_SWITCH 33 bool "Marvel MV88E61xx Ethernet switch PHY support." 34 35if MV88E61XX_SWITCH 36 37config MV88E61XX_CPU_PORT 38 int "CPU Port" 39 40config MV88E61XX_PHY_PORTS 41 hex "Bitmask of PHY Ports" 42 43config MV88E61XX_FIXED_PORTS 44 hex "Bitmask of PHYless serdes Ports" 45 46endif # MV88E61XX_SWITCH 47 48config PHYLIB_10G 49 bool "Generic 10G PHY support" 50 51config PHY_AQUANTIA 52 bool "Aquantia Ethernet PHYs support" 53 54config PHY_ATHEROS 55 bool "Atheros Ethernet PHYs support" 56 57config PHY_BROADCOM 58 bool "Broadcom Ethernet PHYs support" 59 60config PHY_CORTINA 61 bool "Cortina Ethernet PHYs support" 62 63config PHY_DAVICOM 64 bool "Davicom Ethernet PHYs support" 65 66config PHY_ET1011C 67 bool "LSI TruePHY ET1011C support" 68 69config PHY_LXT 70 bool "LXT971 Ethernet PHY support" 71 72config PHY_MARVELL 73 bool "Marvell Ethernet PHYs support" 74 75config PHY_MESON_GXL 76 bool "Amlogic Meson GXL Internal PHY support" 77 78config PHY_MICREL 79 bool "Micrel Ethernet PHYs support" 80 help 81 Enable support for the GbE PHYs manufactured by Micrel (now 82 a part of Microchip). This includes drivers for the KSZ804, 83 KSZ8031, KSZ8051, KSZ8081, KSZ8895, KSZ886x, KSZ8721 84 either/or KSZ9021 (see the "Micrel KSZ9021 family support" 85 config option for details), and KSZ9031 (if configured). 86 87if PHY_MICREL 88 89config PHY_MICREL_KSZ9021 90 bool 91 select PHY_GIGE 92 select PHY_MICREL_KSZ90X1 93 94config PHY_MICREL_KSZ9031 95 bool 96 select PHY_GIGE 97 select PHY_MICREL_KSZ90X1 98 99config PHY_MICREL_KSZ90X1 100 bool "Micrel KSZ90x1 family support" 101 select PHY_GIGE 102 help 103 Enable support for the Micrel KSZ9021 and KSZ9031 GbE PHYs. If 104 enabled, the extended register read/write for KSZ90x1 PHYs 105 is supported through the 'mdio' command and any RGMII signal 106 delays configured in the device tree will be applied to the 107 PHY during initialization. 108 109 This should not be enabled at the same time with PHY_MICREL_KSZ8XXX 110 as the KSZ9021 and KS8721 share the same ID. 111 112config PHY_MICREL_KSZ8XXX 113 bool "Micrel KSZ8xxx family support" 114 default y if !PHY_MICREL_KSZ90X1 115 help 116 Enable support for the 8000 series GbE PHYs manufactured by Micrel 117 (now a part of Microchip). This includes drivers for the KSZ804, 118 KSZ8031, KSZ8051, KSZ8081, KSZ8895, KSZ886x, and KSZ8721. 119 120 This should not be enabled at the same time with PHY_MICREL_KSZ90X1 121 as the KSZ9021 and KS8721 share the same ID. 122 123endif # PHY_MICREL 124 125config PHY_MSCC 126 bool "Microsemi Corp Ethernet PHYs support" 127 128config PHY_NATSEMI 129 bool "National Semiconductor Ethernet PHYs support" 130 131config PHY_REALTEK 132 bool "Realtek Ethernet PHYs support" 133 134config RTL8211X_PHY_FORCE_MASTER 135 bool "Ethernet PHY RTL8211x: force 1000BASE-T master mode" 136 depends on PHY_REALTEK 137 help 138 Force master mode for 1000BASE-T on RTl8211x PHYs (except for RTL8211F). 139 This can work around link stability and data corruption issues on gigabit 140 links which can occur in slave mode on certain PHYs, e.g. on the 141 RTL8211C(L). 142 143 Please note that two directly connected devices (i.e. via crossover cable) 144 will not be able to establish a link between each other if they both force 145 master mode. Multiple devices forcing master mode when connected by a 146 network switch do not pose a problem as the switch configures its affected 147 ports into slave mode. 148 149 This option only affects gigabit links. If you must establish a direct 150 connection between two devices which both force master mode, try forcing 151 the link speed to 100MBit/s. 152 153 If unsure, say N. 154 155config PHY_SMSC 156 bool "Microchip(SMSC) Ethernet PHYs support" 157 158config PHY_TERANETICS 159 bool "Teranetics Ethernet PHYs support" 160 161config PHY_TI 162 bool "Texas Instruments Ethernet PHYs support" 163 164config PHY_VITESSE 165 bool "Vitesse Ethernet PHYs support" 166 167config PHY_XILINX 168 bool "Xilinx Ethernet PHYs support" 169 170config PHY_FIXED 171 bool "Fixed-Link PHY" 172 depends on DM_ETH 173 help 174 Fixed PHY is used for having a 'fixed-link' to another MAC with a direct 175 connection (MII, RGMII, ...). 176 There is nothing like autoneogation and so 177 on, the link is always up with fixed speed and fixed duplex-setting. 178 More information: doc/device-tree-bindings/net/fixed-link.txt 179 180endif #PHYLIB 181