1source "drivers/net/phy/Kconfig" 2source "drivers/net/pfe_eth/Kconfig" 3 4config DM_ETH 5 bool "Enable Driver Model for Ethernet drivers" 6 depends on DM 7 help 8 Enable driver model for Ethernet. 9 10 The eth_*() interface will be implemented by the UCLASS_ETH class 11 This is currently implemented in net/eth-uclass.c 12 Look in include/net.h for details. 13 14config DRIVER_TI_CPSW 15 bool "TI Common Platform Ethernet Switch" 16 select PHYLIB 17 help 18 This driver supports the TI three port switch gigabit ethernet 19 subsystem found in the TI SoCs. 20 21menuconfig NETDEVICES 22 bool "Network device support" 23 depends on NET 24 default y if DM_ETH 25 help 26 You must select Y to enable any network device support 27 Generally if you have any networking support this is a given 28 29 If unsure, say Y 30 31if NETDEVICES 32 33config PHY_GIGE 34 bool "Enable GbE PHY status parsing and configuration" 35 help 36 Enables support for parsing the status output and for 37 configuring GbE PHYs (affects the inner workings of some 38 commands and miiphyutil.c). 39 40config AG7XXX 41 bool "Atheros AG7xxx Ethernet MAC support" 42 depends on DM_ETH && ARCH_ATH79 43 select PHYLIB 44 help 45 This driver supports the Atheros AG7xxx Ethernet MAC. This MAC is 46 present in the Atheros AR7xxx, AR9xxx and QCA9xxx MIPS chips. 47 48 49config ALTERA_TSE 50 bool "Altera Triple-Speed Ethernet MAC support" 51 depends on DM_ETH 52 select PHYLIB 53 help 54 This driver supports the Altera Triple-Speed (TSE) Ethernet MAC. 55 Please find details on the "Triple-Speed Ethernet MegaCore Function 56 Resource Center" of Altera. 57 58config BCM_SF2_ETH 59 bool "Broadcom SF2 (Starfighter2) Ethernet support" 60 select PHYLIB 61 help 62 This is an abstract framework which provides a generic interface 63 to MAC and DMA management for multiple Broadcom SoCs such as 64 Cygnus, NSP and bcm28155_ap platforms. 65 66config BCM_SF2_ETH_DEFAULT_PORT 67 int "Broadcom SF2 (Starfighter2) Ethernet default port number" 68 depends on BCM_SF2_ETH 69 default 0 70 help 71 Default port number for the Starfighter2 ethernet driver. 72 73config BCM_SF2_ETH_GMAC 74 bool "Broadcom SF2 (Starfighter2) GMAC Ethernet support" 75 depends on BCM_SF2_ETH 76 help 77 This flag enables the ethernet support for Broadcom platforms with 78 GMAC such as Cygnus. This driver is based on the framework provided 79 by the BCM_SF2_ETH driver. 80 Say Y to any bcmcygnus based platforms. 81 82config DWC_ETH_QOS 83 bool "Synopsys DWC Ethernet QOS device support" 84 depends on DM_ETH 85 select PHYLIB 86 help 87 This driver supports the Synopsys Designware Ethernet QOS (Quality 88 Of Service) IP block. The IP supports many options for bus type, 89 clocking/reset structure, and feature list. This driver currently 90 supports the specific configuration used in NVIDIA's Tegra186 chip, 91 but should be extensible to other combinations quite easily. 92 93config E1000 94 bool "Intel PRO/1000 Gigabit Ethernet support" 95 help 96 This driver supports Intel(R) PRO/1000 gigabit ethernet family of 97 adapters. For more information on how to identify your adapter, go 98 to the Adapter & Driver ID Guide at: 99 100 <http://support.intel.com/support/network/adapter/pro100/21397.htm> 101 102config E1000_SPI_GENERIC 103 bool "Allow access to the Intel 8257x SPI bus" 104 depends on E1000 105 help 106 Allow generic access to the SPI bus on the Intel 8257x, for 107 example with the "sspi" command. 108 109config E1000_SPI 110 bool "Enable SPI bus utility code" 111 depends on E1000 112 help 113 Utility code for direct access to the SPI bus on Intel 8257x. 114 This does not do anything useful unless you set at least one 115 of CONFIG_CMD_E1000 or CONFIG_E1000_SPI_GENERIC. 116 117config CMD_E1000 118 bool "Enable the e1000 command" 119 depends on E1000 120 help 121 This enables the 'e1000' management command for E1000 devices. When 122 used on devices with SPI support you can reprogram the EEPROM from 123 U-Boot. 124 125config ETH_SANDBOX 126 depends on DM_ETH && SANDBOX 127 default y 128 bool "Sandbox: Mocked Ethernet driver" 129 help 130 This driver simply responds with fake ARP replies and ping 131 replies that are used to verify network stack functionality 132 133 This driver is particularly useful in the test/dm/eth.c tests 134 135config ETH_SANDBOX_RAW 136 depends on DM_ETH && SANDBOX 137 default y 138 bool "Sandbox: Bridge to Linux Raw Sockets" 139 help 140 This driver is a bridge from the bottom of the network stack 141 in U-Boot to the RAW AF_PACKET API in Linux. This allows real 142 network traffic to be tested from within sandbox. See 143 board/sandbox/README.sandbox for more details. 144 145config ETH_DESIGNWARE 146 bool "Synopsys Designware Ethernet MAC" 147 select PHYLIB 148 help 149 This MAC is present in SoCs from various vendors. It supports 150 100Mbit and 1 Gbit operation. You must enable CONFIG_PHYLIB to 151 provide the PHY (physical media interface). 152 153config ETH_DESIGNWARE_SOCFPGA 154 bool "Altera SoCFPGA extras for Synopsys Designware Ethernet MAC" 155 depends on DM_ETH && ETH_DESIGNWARE 156 help 157 The Altera SoCFPGA requires additional configuration of the 158 Altera system manager to correctly interface with the PHY. 159 This code handles those SoC specifics. 160 161config ETHOC 162 bool "OpenCores 10/100 Mbps Ethernet MAC" 163 help 164 This MAC is present in OpenRISC and Xtensa XTFPGA boards. 165 166config FEC_MXC_SHARE_MDIO 167 bool "Share the MDIO bus for FEC controller" 168 depends on FEC_MXC 169 170config FEC_MXC_MDIO_BASE 171 hex "MDIO base address for the FEC controller" 172 depends on FEC_MXC_SHARE_MDIO 173 help 174 This specifies the MDIO registers base address. It is used when 175 two FEC controllers share MDIO bus. 176 177config FEC_MXC 178 bool "FEC Ethernet controller" 179 depends on MX5 || MX6 || MX7 180 help 181 This driver supports the 10/100 Fast Ethernet controller for 182 NXP i.MX processors. 183 184config FTMAC100 185 bool "Ftmac100 Ethernet Support" 186 help 187 This MAC is present in Andestech SoCs. 188 189config MVGBE 190 bool "Marvell Orion5x/Kirkwood network interface support" 191 depends on KIRKWOOD || ORION5X 192 select PHYLIB if DM_ETH 193 help 194 This driver supports the network interface units in the 195 Marvell Orion5x and Kirkwood SoCs 196 197config MVNETA 198 bool "Marvell Armada XP/385/3700 network interface support" 199 depends on ARMADA_XP || ARMADA_38X || ARMADA_3700 200 select PHYLIB 201 help 202 This driver supports the network interface units in the 203 Marvell ARMADA XP, ARMADA 38X and ARMADA 3700 SoCs 204 205config MVPP2 206 bool "Marvell Armada 375/7K/8K network interface support" 207 depends on ARMADA_375 || ARMADA_8K 208 select PHYLIB 209 help 210 This driver supports the network interface units in the 211 Marvell ARMADA 375, 7K and 8K SoCs. 212 213config MACB 214 bool "Cadence MACB/GEM Ethernet Interface" 215 depends on DM_ETH 216 select PHYLIB 217 help 218 The Cadence MACB ethernet interface is found on many Atmel 219 AT91 and SAMA5 parts. This driver also supports the Cadence 220 GEM (Gigabit Ethernet MAC) found in some ARM SoC devices. 221 Say Y to include support for the MACB/GEM chip. 222 223config MACB_ZYNQ 224 bool "Cadence MACB/GEM Ethernet Interface for Xilinx Zynq" 225 depends on MACB 226 help 227 The Cadence MACB ethernet interface was used on Zynq platform. 228 Say Y to enable support for the MACB/GEM in Zynq chip. 229 230config PCH_GBE 231 bool "Intel Platform Controller Hub EG20T GMAC driver" 232 depends on DM_ETH && DM_PCI 233 select PHYLIB 234 help 235 This MAC is present in Intel Platform Controller Hub EG20T. It 236 supports 10/100/1000 Mbps operation. 237 238config RGMII 239 bool "Enable RGMII" 240 help 241 Enable the support of the Reduced Gigabit Media-Independent 242 Interface (RGMII). 243 244config MII 245 bool "Enable MII" 246 help 247 Enable support of the Media-Independent Interface (MII) 248 249config RTL8139 250 bool "Realtek 8139 series Ethernet controller driver" 251 help 252 This driver supports Realtek 8139 series fast ethernet family of 253 PCI chipsets/adapters. 254 255config RTL8169 256 bool "Realtek 8169 series Ethernet controller driver" 257 help 258 This driver supports Realtek 8169 series gigabit ethernet family of 259 PCI/PCIe chipsets/adapters. 260 261config SMC911X 262 bool "SMSC LAN911x and LAN921x controller driver" 263 264if SMC911X 265 266config SMC911X_BASE 267 hex "SMC911X Base Address" 268 help 269 Define this to hold the physical address 270 of the device (I/O space) 271 272choice 273 prompt "SMC911X bus width" 274 default SMC911X_16_BIT 275 276config SMC911X_32_BIT 277 bool "Enable 32-bit interface" 278 279config SMC911X_16_BIT 280 bool "Enable 16-bit interface" 281 help 282 Define this if data bus is 16 bits. If your processor 283 automatically converts one 32 bit word to two 16 bit 284 words you may also try CONFIG_SMC911X_32_BIT. 285 286endchoice 287endif #SMC911X 288 289config SUN7I_GMAC 290 bool "Enable Allwinner GMAC Ethernet support" 291 help 292 Enable the support for Sun7i GMAC Ethernet controller 293 294config SUN7I_GMAC_FORCE_TXERR 295 bool "Force PA17 as gmac function" 296 depends on SUN7I_GMAC 297 help 298 Some ethernet phys needs TXERR control. Since the GMAC 299 doesn't have such signal, setting PA17 as GMAC function 300 makes the pin output low, which enables data transmission. 301 302config SUN4I_EMAC 303 bool "Allwinner Sun4i Ethernet MAC support" 304 depends on DM_ETH 305 select PHYLIB 306 help 307 This driver supports the Allwinner based SUN4I Ethernet MAC. 308 309config SUN8I_EMAC 310 bool "Allwinner Sun8i Ethernet MAC support" 311 depends on DM_ETH 312 select PHYLIB 313 select PHY_GIGE 314 help 315 This driver supports the Allwinner based SUN8I/SUN50I Ethernet MAC. 316 It can be found in H3/A64/A83T based SoCs and compatible with both 317 External and Internal PHYs. 318 319config SH_ETHER 320 bool "Renesas SH Ethernet MAC" 321 select PHYLIB 322 help 323 This driver supports the Ethernet for Renesas SH and ARM SoCs. 324 325config DRIVER_TI_EMAC 326 bool "TI Davinci EMAC" 327 help 328 Support for davinci emac 329 330config XILINX_AXIEMAC 331 depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP) 332 select PHYLIB 333 select MII 334 bool "Xilinx AXI Ethernet" 335 help 336 This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs. 337 338config XILINX_EMACLITE 339 depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP || MIPS) 340 select PHYLIB 341 select MII 342 bool "Xilinx Ethernetlite" 343 help 344 This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs. 345 346config ZYNQ_GEM 347 depends on DM_ETH && (ARCH_ZYNQ || ARCH_ZYNQMP) 348 select PHYLIB 349 bool "Xilinx Ethernet GEM" 350 help 351 This MAC is present in Xilinx Zynq and ZynqMP SoCs. 352 353config PIC32_ETH 354 bool "Microchip PIC32 Ethernet Support" 355 depends on DM_ETH && MACH_PIC32 356 select PHYLIB 357 help 358 This driver implements 10/100 Mbps Ethernet and MAC layer for 359 Microchip PIC32 microcontrollers. 360 361config GMAC_ROCKCHIP 362 bool "Rockchip Synopsys Designware Ethernet MAC" 363 depends on DM_ETH && ETH_DESIGNWARE 364 help 365 This driver provides Rockchip SoCs network support based on the 366 Synopsys Designware driver. 367 368config RENESAS_RAVB 369 bool "Renesas Ethernet AVB MAC" 370 depends on DM_ETH && RCAR_GEN3 371 select PHYLIB 372 help 373 This driver implements support for the Ethernet AVB block in 374 Renesas M3 and H3 SoCs. 375 376config MPC8XX_FEC 377 bool "Fast Ethernet Controller on MPC8XX" 378 depends on MPC8xx 379 select MII 380 help 381 This driver implements support for the Fast Ethernet Controller 382 on MPC8XX 383 384config SNI_AVE 385 bool "Socionext AVE Ethernet support" 386 depends on DM_ETH && ARCH_UNIPHIER 387 select PHYLIB 388 select SYSCON 389 select REGMAP 390 help 391 This driver implements support for the Socionext AVE Ethernet 392 controller, as found on the Socionext UniPhier family. 393 394config ETHER_ON_FEC1 395 bool "FEC1" 396 depends on MPC8XX_FEC 397 default y 398 399config FEC1_PHY 400 int "FEC1 PHY" 401 depends on ETHER_ON_FEC1 402 default -1 403 help 404 Define to the hardcoded PHY address which corresponds 405 to the given FEC; i. e. 406 #define CONFIG_FEC1_PHY 4 407 means that the PHY with address 4 is connected to FEC1 408 409 When set to -1, means to probe for first available. 410 411config PHY_NORXERR 412 bool "PHY_NORXERR" 413 depends on ETHER_ON_FEC1 414 default n 415 help 416 The PHY does not have a RXERR line (RMII only). 417 (so program the FEC to ignore it). 418 419config ETHER_ON_FEC2 420 bool "FEC2" 421 depends on MPC8XX_FEC && MPC885 422 default y 423 424config FEC2_PHY 425 int "FEC2 PHY" 426 depends on ETHER_ON_FEC2 427 default -1 428 help 429 Define to the hardcoded PHY address which corresponds 430 to the given FEC; i. e. 431 #define CONFIG_FEC1_PHY 4 432 means that the PHY with address 4 is connected to FEC1 433 434 When set to -1, means to probe for first available. 435 436config FEC2_PHY_NORXERR 437 bool "PHY_NORXERR" 438 depends on ETHER_ON_FEC2 439 default n 440 help 441 The PHY does not have a RXERR line (RMII only). 442 (so program the FEC to ignore it). 443 444config SYS_DPAA_QBMAN 445 bool "Device tree fixup for QBMan on freescale SOCs" 446 depends on (ARM || PPC) && !SPL_BUILD 447 default y if ARCH_B4860 || \ 448 ARCH_B4420 || \ 449 ARCH_P1023 || \ 450 ARCH_P2041 || \ 451 ARCH_T1023 || \ 452 ARCH_T1024 || \ 453 ARCH_T1040 || \ 454 ARCH_T1042 || \ 455 ARCH_T2080 || \ 456 ARCH_T2081 || \ 457 ARCH_T4240 || \ 458 ARCH_T4160 || \ 459 ARCH_P4080 || \ 460 ARCH_P3041 || \ 461 ARCH_P5040 || \ 462 ARCH_P5020 || \ 463 ARCH_LS1043A || \ 464 ARCH_LS1046A 465 help 466 QBman fixups to allow deep sleep in DPAA 1 SOCs 467 468config TSEC_ENET 469 select PHYLIB 470 bool "Enable Three-Speed Ethernet Controller" 471 help 472 This driver implements support for the (Enhanced) Three-Speed 473 Ethernet Controller found on Freescale SoCs. 474 475endif # NETDEVICES 476