xref: /openbmc/u-boot/drivers/net/Kconfig (revision f739fcd8)
1source "drivers/net/phy/Kconfig"
2source "drivers/net/pfe_eth/Kconfig"
3
4config DM_ETH
5	bool "Enable Driver Model for Ethernet drivers"
6	depends on DM
7	help
8	  Enable driver model for Ethernet.
9
10	  The eth_*() interface will be implemented by the UC_ETH class
11	  This is currently implemented in net/eth.c
12	  Look in include/net.h for details.
13
14config DRIVER_TI_CPSW
15	bool "TI Common Platform Ethernet Switch"
16	select PHYLIB
17	help
18	  This driver supports the TI three port switch gigabit ethernet
19	  subsystem found in the TI SoCs.
20
21menuconfig NETDEVICES
22	bool "Network device support"
23	depends on NET
24	default y if DM_ETH
25	help
26	  You must select Y to enable any network device support
27	  Generally if you have any networking support this is a given
28
29	  If unsure, say Y
30
31if NETDEVICES
32
33config PHY_GIGE
34	bool "Enable GbE PHY status parsing and configuration"
35	help
36	  Enables support for parsing the status output and for
37	  configuring GbE PHYs (affects the inner workings of some
38	  commands and miiphyutil.c).
39
40config AG7XXX
41	bool "Atheros AG7xxx Ethernet MAC support"
42	depends on DM_ETH && ARCH_ATH79
43	select PHYLIB
44	help
45	  This driver supports the Atheros AG7xxx Ethernet MAC. This MAC is
46	  present in the Atheros AR7xxx, AR9xxx and QCA9xxx MIPS chips.
47
48
49config ALTERA_TSE
50	bool "Altera Triple-Speed Ethernet MAC support"
51	depends on DM_ETH
52	select PHYLIB
53	help
54	  This driver supports the Altera Triple-Speed (TSE) Ethernet MAC.
55	  Please find details on the "Triple-Speed Ethernet MegaCore Function
56	  Resource Center" of Altera.
57
58config BCM_SF2_ETH
59	bool "Broadcom SF2 (Starfighter2) Ethernet support"
60	select PHYLIB
61	help
62	  This is an abstract framework which provides a generic interface
63	  to MAC and DMA management for multiple Broadcom SoCs such as
64	  Cygnus, NSP and bcm28155_ap platforms.
65
66config BCM_SF2_ETH_DEFAULT_PORT
67	int "Broadcom SF2 (Starfighter2) Ethernet default port number"
68	depends on BCM_SF2_ETH
69	default 0
70	help
71	  Default port number for the Starfighter2 ethernet driver.
72
73config BCM_SF2_ETH_GMAC
74	bool "Broadcom SF2 (Starfighter2) GMAC Ethernet support"
75	depends on BCM_SF2_ETH
76	help
77	  This flag enables the ethernet support for Broadcom platforms with
78	  GMAC such as Cygnus. This driver is based on the framework provided
79	  by the BCM_SF2_ETH driver.
80	  Say Y to any bcmcygnus based platforms.
81
82config DWC_ETH_QOS
83	bool "Synopsys DWC Ethernet QOS device support"
84	depends on DM_ETH
85	select PHYLIB
86	help
87	  This driver supports the Synopsys Designware Ethernet QOS (Quality
88	  Of Service) IP block. The IP supports many options for bus type,
89	  clocking/reset structure, and feature list. This driver currently
90	  supports the specific configuration used in NVIDIA's Tegra186 chip,
91	  but should be extensible to other combinations quite easily.
92
93config E1000
94	bool "Intel PRO/1000 Gigabit Ethernet support"
95	help
96	  This driver supports Intel(R) PRO/1000 gigabit ethernet family of
97	  adapters.  For more information on how to identify your adapter, go
98	  to the Adapter & Driver ID Guide at:
99
100	  <http://support.intel.com/support/network/adapter/pro100/21397.htm>
101
102config E1000_SPI_GENERIC
103	bool "Allow access to the Intel 8257x SPI bus"
104	depends on E1000
105	help
106	  Allow generic access to the SPI bus on the Intel 8257x, for
107	  example with the "sspi" command.
108
109config E1000_SPI
110	bool "Enable SPI bus utility code"
111	depends on E1000
112	help
113	  Utility code for direct access to the SPI bus on Intel 8257x.
114	  This does not do anything useful unless you set at least one
115	  of CONFIG_CMD_E1000 or CONFIG_E1000_SPI_GENERIC.
116
117config CMD_E1000
118	bool "Enable the e1000 command"
119	depends on E1000
120	help
121	  This enables the 'e1000' management command for E1000 devices. When
122	  used on devices with SPI support you can reprogram the EEPROM from
123	  U-Boot.
124
125config ETH_SANDBOX
126	depends on DM_ETH && SANDBOX
127	default y
128	bool "Sandbox: Mocked Ethernet driver"
129	help
130	  This driver simply responds with fake ARP replies and ping
131	  replies that are used to verify network stack functionality
132
133	  This driver is particularly useful in the test/dm/eth.c tests
134
135config ETH_SANDBOX_RAW
136	depends on DM_ETH && SANDBOX
137	default y
138	bool "Sandbox: Bridge to Linux Raw Sockets"
139	help
140	  This driver is a bridge from the bottom of the network stack
141	  in U-Boot to the RAW AF_PACKET API in Linux. This allows real
142	  network traffic to be tested from within sandbox. See
143	  board/sandbox/README.sandbox for more details.
144
145config ETH_DESIGNWARE
146	bool "Synopsys Designware Ethernet MAC"
147	select PHYLIB
148	help
149	  This MAC is present in SoCs from various vendors. It supports
150	  100Mbit and 1 Gbit operation. You must enable CONFIG_PHYLIB to
151	  provide the PHY (physical media interface).
152
153config ETHOC
154	bool "OpenCores 10/100 Mbps Ethernet MAC"
155	help
156	  This MAC is present in OpenRISC and Xtensa XTFPGA boards.
157
158config FEC_MXC_SHARE_MDIO
159	bool "Share the MDIO bus for FEC controller"
160	depends on FEC_MXC
161
162config FEC_MXC_MDIO_BASE
163	hex "MDIO base address for the FEC controller"
164	depends on FEC_MXC_SHARE_MDIO
165	help
166	  This specifies the MDIO registers base address. It is used when
167	  two FEC controllers share MDIO bus.
168
169config FEC_MXC
170	bool "FEC Ethernet controller"
171	depends on MX5 || MX6 || MX7
172	help
173	  This driver supports the 10/100 Fast Ethernet controller for
174	  NXP i.MX processors.
175
176config FTMAC100
177	bool "Ftmac100 Ethernet Support"
178	help
179	  This MAC is present in Andestech SoCs.
180
181config MVNETA
182	bool "Marvell Armada XP/385/3700 network interface support"
183	depends on ARMADA_XP || ARMADA_38X || ARMADA_3700
184	select PHYLIB
185	help
186	  This driver supports the network interface units in the
187	  Marvell ARMADA XP, ARMADA 38X and ARMADA 3700 SoCs
188
189config MVPP2
190	bool "Marvell Armada 375/7K/8K network interface support"
191	depends on ARMADA_375 || ARMADA_8K
192	select PHYLIB
193	help
194	  This driver supports the network interface units in the
195	  Marvell ARMADA 375, 7K and 8K SoCs.
196
197config MACB
198	bool "Cadence MACB/GEM Ethernet Interface"
199	depends on DM_ETH
200	select PHYLIB
201	help
202	  The Cadence MACB ethernet interface is found on many Atmel
203	  AT91 and SAMA5 parts.  This driver also supports the Cadence
204	  GEM (Gigabit Ethernet MAC) found in some ARM SoC devices.
205	  Say Y to include support for the MACB/GEM chip.
206
207config MACB_ZYNQ
208	bool "Cadence MACB/GEM Ethernet Interface for Xilinx Zynq"
209	depends on MACB
210	help
211	  The Cadence MACB ethernet interface was used on Zynq platform.
212	  Say Y to enable support for the MACB/GEM in Zynq chip.
213
214config PCH_GBE
215	bool "Intel Platform Controller Hub EG20T GMAC driver"
216	depends on DM_ETH && DM_PCI
217	select PHYLIB
218	help
219	  This MAC is present in Intel Platform Controller Hub EG20T. It
220	  supports 10/100/1000 Mbps operation.
221
222config RGMII
223	bool "Enable RGMII"
224	help
225	  Enable the support of the Reduced Gigabit Media-Independent
226	  Interface (RGMII).
227
228config RTL8139
229	bool "Realtek 8139 series Ethernet controller driver"
230	help
231	  This driver supports Realtek 8139 series fast ethernet family of
232	  PCI chipsets/adapters.
233
234config RTL8169
235	bool "Realtek 8169 series Ethernet controller driver"
236	help
237	  This driver supports Realtek 8169 series gigabit ethernet family of
238	  PCI/PCIe chipsets/adapters.
239
240config SMC911X
241	bool "SMSC LAN911x and LAN921x controller driver"
242
243if SMC911X
244
245config SMC911X_BASE
246	hex "SMC911X Base Address"
247	help
248	  Define this to hold the physical address
249	  of the device (I/O space)
250
251choice
252	prompt "SMC911X bus width"
253	default SMC911X_16_BIT
254
255config SMC911X_32_BIT
256	bool "Enable 32-bit interface"
257
258config SMC911X_16_BIT
259	bool "Enable 16-bit interface"
260	help
261	  Define this if data bus is 16 bits. If your processor
262	  automatically converts one 32 bit word to two 16 bit
263	  words you may also try CONFIG_SMC911X_32_BIT.
264
265endchoice
266endif #SMC911X
267
268config SUN7I_GMAC
269	bool "Enable Allwinner GMAC Ethernet support"
270	help
271	  Enable the support for Sun7i GMAC Ethernet controller
272
273config SUN7I_GMAC_FORCE_TXERR
274	bool "Force PA17 as gmac function"
275	depends on SUN7I_GMAC
276	help
277	  Some ethernet phys needs TXERR control. Since the GMAC
278	  doesn't have such signal, setting PA17 as GMAC function
279	  makes the pin output low, which enables data transmission.
280
281config SUN4I_EMAC
282	bool "Allwinner Sun4i Ethernet MAC support"
283	depends on DM_ETH
284	select PHYLIB
285	help
286	  This driver supports the Allwinner based SUN4I Ethernet MAC.
287
288config SUN8I_EMAC
289        bool "Allwinner Sun8i Ethernet MAC support"
290        depends on DM_ETH
291        select PHYLIB
292	select PHY_GIGE
293        help
294          This driver supports the  Allwinner based SUN8I/SUN50I Ethernet MAC.
295	  It can be found in H3/A64/A83T based SoCs and compatible with both
296	  External and Internal PHYs.
297
298config SH_ETHER
299	bool "Renesas SH Ethernet MAC"
300	select PHYLIB
301	help
302	  This driver supports the Ethernet for Renesas SH and ARM SoCs.
303
304config XILINX_AXIEMAC
305	depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP)
306	select PHYLIB
307	select MII
308	bool "Xilinx AXI Ethernet"
309	help
310	  This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs.
311
312config XILINX_EMACLITE
313	depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP || MIPS)
314	select PHYLIB
315	select MII
316	bool "Xilinx Ethernetlite"
317	help
318	  This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs.
319
320config ZYNQ_GEM
321	depends on DM_ETH && (ARCH_ZYNQ || ARCH_ZYNQMP)
322	select PHYLIB
323	bool "Xilinx Ethernet GEM"
324	help
325	  This MAC is present in Xilinx Zynq and ZynqMP SoCs.
326
327config PIC32_ETH
328	bool "Microchip PIC32 Ethernet Support"
329	depends on DM_ETH && MACH_PIC32
330	select PHYLIB
331	help
332	  This driver implements 10/100 Mbps Ethernet and MAC layer for
333	  Microchip PIC32 microcontrollers.
334
335config GMAC_ROCKCHIP
336	bool "Rockchip Synopsys Designware Ethernet MAC"
337	depends on DM_ETH && ETH_DESIGNWARE
338	help
339	  This driver provides Rockchip SoCs network support based on the
340	  Synopsys Designware driver.
341
342config RENESAS_RAVB
343	bool "Renesas Ethernet AVB MAC"
344	depends on DM_ETH && RCAR_GEN3
345	select PHYLIB
346	help
347	  This driver implements support for the Ethernet AVB block in
348	  Renesas M3 and H3 SoCs.
349
350config MPC8XX_FEC
351	bool "Fast Ethernet Controller on MPC8XX"
352	depends on MPC8xx
353	select MII
354	help
355	  This driver implements support for the Fast Ethernet Controller
356	  on MPC8XX
357
358config ETHER_ON_FEC1
359	bool "FEC1"
360	depends on MPC8XX_FEC
361	default y
362
363config FEC1_PHY
364	int "FEC1 PHY"
365	depends on ETHER_ON_FEC1
366	default -1
367	help
368	  Define to the hardcoded PHY address which corresponds
369	  to the given FEC; i. e.
370		#define CONFIG_FEC1_PHY 4
371	  means that the PHY with address 4 is connected to FEC1
372
373	  When set to -1, means to probe for first available.
374
375config PHY_NORXERR
376	bool "PHY_NORXERR"
377	depends on ETHER_ON_FEC1
378	default n
379	help
380	  The PHY does not have a RXERR line (RMII only).
381	  (so program the FEC to ignore it).
382
383config ETHER_ON_FEC2
384	bool "FEC2"
385	depends on MPC8XX_FEC && MPC885
386	default y
387
388config FEC2_PHY
389	int "FEC2 PHY"
390	depends on ETHER_ON_FEC2
391	default -1
392	help
393	  Define to the hardcoded PHY address which corresponds
394	  to the given FEC; i. e.
395		#define CONFIG_FEC1_PHY 4
396	  means that the PHY with address 4 is connected to FEC1
397
398	  When set to -1, means to probe for first available.
399
400config FEC2_PHY_NORXERR
401	bool "PHY_NORXERR"
402	depends on ETHER_ON_FEC2
403	default n
404	help
405	  The PHY does not have a RXERR line (RMII only).
406	  (so program the FEC to ignore it).
407
408config SYS_DPAA_QBMAN
409	bool "Device tree fixup for QBMan on freescale SOCs"
410	depends on (ARM || PPC) && !SPL_BUILD
411	default y if ARCH_B4860 || \
412		     ARCH_B4420 || \
413		     ARCH_P1023 || \
414		     ARCH_P2041 || \
415		     ARCH_T1023 || \
416		     ARCH_T1024 || \
417		     ARCH_T1040 || \
418		     ARCH_T1042 || \
419		     ARCH_T2080 || \
420		     ARCH_T2081 || \
421		     ARCH_T4240 || \
422		     ARCH_T4160 || \
423		     ARCH_P4080 || \
424		     ARCH_P3041 || \
425		     ARCH_P5040 || \
426		     ARCH_P5020 || \
427		     ARCH_LS1043A || \
428		     ARCH_LS1046A
429	help
430	  QBman fixups to allow deep sleep in DPAA 1 SOCs
431
432config TSEC_ENET
433	select PHYLIB
434	bool "Enable Three-Speed Ethernet Controller"
435	help
436	  This driver implements support for the (Enhanced) Three-Speed
437	  Ethernet Controller found on Freescale SoCs.
438
439endif # NETDEVICES
440