xref: /openbmc/u-boot/drivers/net/Kconfig (revision d32aa3ca)
1source "drivers/net/phy/Kconfig"
2source "drivers/net/pfe_eth/Kconfig"
3
4config DM_ETH
5	bool "Enable Driver Model for Ethernet drivers"
6	depends on DM
7	help
8	  Enable driver model for Ethernet.
9
10	  The eth_*() interface will be implemented by the UCLASS_ETH class
11	  This is currently implemented in net/eth-uclass.c
12	  Look in include/net.h for details.
13
14menuconfig NETDEVICES
15	bool "Network device support"
16	depends on NET
17	default y if DM_ETH
18	help
19	  You must select Y to enable any network device support
20	  Generally if you have any networking support this is a given
21
22	  If unsure, say Y
23
24if NETDEVICES
25
26config PHY_GIGE
27	bool "Enable GbE PHY status parsing and configuration"
28	help
29	  Enables support for parsing the status output and for
30	  configuring GbE PHYs (affects the inner workings of some
31	  commands and miiphyutil.c).
32
33config AG7XXX
34	bool "Atheros AG7xxx Ethernet MAC support"
35	depends on DM_ETH && ARCH_ATH79
36	select PHYLIB
37	help
38	  This driver supports the Atheros AG7xxx Ethernet MAC. This MAC is
39	  present in the Atheros AR7xxx, AR9xxx and QCA9xxx MIPS chips.
40
41
42config ALTERA_TSE
43	bool "Altera Triple-Speed Ethernet MAC support"
44	depends on DM_ETH
45	select PHYLIB
46	help
47	  This driver supports the Altera Triple-Speed (TSE) Ethernet MAC.
48	  Please find details on the "Triple-Speed Ethernet MegaCore Function
49	  Resource Center" of Altera.
50
51config BCM_SF2_ETH
52	bool "Broadcom SF2 (Starfighter2) Ethernet support"
53	select PHYLIB
54	help
55	  This is an abstract framework which provides a generic interface
56	  to MAC and DMA management for multiple Broadcom SoCs such as
57	  Cygnus, NSP and bcm28155_ap platforms.
58
59config BCM_SF2_ETH_DEFAULT_PORT
60	int "Broadcom SF2 (Starfighter2) Ethernet default port number"
61	depends on BCM_SF2_ETH
62	default 0
63	help
64	  Default port number for the Starfighter2 ethernet driver.
65
66config BCM_SF2_ETH_GMAC
67	bool "Broadcom SF2 (Starfighter2) GMAC Ethernet support"
68	depends on BCM_SF2_ETH
69	help
70	  This flag enables the ethernet support for Broadcom platforms with
71	  GMAC such as Cygnus. This driver is based on the framework provided
72	  by the BCM_SF2_ETH driver.
73	  Say Y to any bcmcygnus based platforms.
74
75config BCM6348_ETH
76	bool "BCM6348 EMAC support"
77	depends on DM_ETH && ARCH_BMIPS
78	select DMA
79	select DMA_CHANNELS
80	select MII
81	select PHYLIB
82	help
83	  This driver supports the BCM6348 Ethernet MAC.
84
85config BCM6368_ETH
86	bool "BCM6368 EMAC support"
87	depends on DM_ETH && ARCH_BMIPS
88	select DMA
89	select MII
90	help
91	  This driver supports the BCM6368 Ethernet MAC.
92
93config DWC_ETH_QOS
94	bool "Synopsys DWC Ethernet QOS device support"
95	depends on DM_ETH
96	select PHYLIB
97	help
98	  This driver supports the Synopsys Designware Ethernet QOS (Quality
99	  Of Service) IP block. The IP supports many options for bus type,
100	  clocking/reset structure, and feature list. This driver currently
101	  supports the specific configuration used in NVIDIA's Tegra186 chip,
102	  but should be extensible to other combinations quite easily.
103
104config E1000
105	bool "Intel PRO/1000 Gigabit Ethernet support"
106	help
107	  This driver supports Intel(R) PRO/1000 gigabit ethernet family of
108	  adapters.  For more information on how to identify your adapter, go
109	  to the Adapter & Driver ID Guide at:
110
111	  <http://support.intel.com/support/network/adapter/pro100/21397.htm>
112
113config E1000_SPI_GENERIC
114	bool "Allow access to the Intel 8257x SPI bus"
115	depends on E1000
116	help
117	  Allow generic access to the SPI bus on the Intel 8257x, for
118	  example with the "sspi" command.
119
120config E1000_SPI
121	bool "Enable SPI bus utility code"
122	depends on E1000
123	help
124	  Utility code for direct access to the SPI bus on Intel 8257x.
125	  This does not do anything useful unless you set at least one
126	  of CONFIG_CMD_E1000 or CONFIG_E1000_SPI_GENERIC.
127
128config CMD_E1000
129	bool "Enable the e1000 command"
130	depends on E1000
131	help
132	  This enables the 'e1000' management command for E1000 devices. When
133	  used on devices with SPI support you can reprogram the EEPROM from
134	  U-Boot.
135
136config ETH_SANDBOX
137	depends on DM_ETH && SANDBOX
138	default y
139	bool "Sandbox: Mocked Ethernet driver"
140	help
141	  This driver simply responds with fake ARP replies and ping
142	  replies that are used to verify network stack functionality
143
144	  This driver is particularly useful in the test/dm/eth.c tests
145
146config ETH_SANDBOX_RAW
147	depends on DM_ETH && SANDBOX
148	default y
149	bool "Sandbox: Bridge to Linux Raw Sockets"
150	help
151	  This driver is a bridge from the bottom of the network stack
152	  in U-Boot to the RAW AF_PACKET API in Linux. This allows real
153	  network traffic to be tested from within sandbox. See
154	  board/sandbox/README.sandbox for more details.
155
156config ETH_DESIGNWARE
157	bool "Synopsys Designware Ethernet MAC"
158	select PHYLIB
159	imply ETH_DESIGNWARE_SOCFPGA if ARCH_SOCFPGA
160	help
161	  This MAC is present in SoCs from various vendors. It supports
162	  100Mbit and 1 Gbit operation. You must enable CONFIG_PHYLIB to
163	  provide the PHY (physical media interface).
164
165config ETH_DESIGNWARE_SOCFPGA
166	select REGMAP
167	select SYSCON
168	bool "Altera SoCFPGA extras for Synopsys Designware Ethernet MAC"
169	depends on DM_ETH && ETH_DESIGNWARE
170	help
171	  The Altera SoCFPGA requires additional configuration of the
172	  Altera system manager to correctly interface with the PHY.
173	  This code handles those SoC specifics.
174
175config ETHOC
176	bool "OpenCores 10/100 Mbps Ethernet MAC"
177	help
178	  This MAC is present in OpenRISC and Xtensa XTFPGA boards.
179
180config FEC_MXC_SHARE_MDIO
181	bool "Share the MDIO bus for FEC controller"
182	depends on FEC_MXC
183
184config FEC_MXC_MDIO_BASE
185	hex "MDIO base address for the FEC controller"
186	depends on FEC_MXC_SHARE_MDIO
187	help
188	  This specifies the MDIO registers base address. It is used when
189	  two FEC controllers share MDIO bus.
190
191config FEC_MXC
192	bool "FEC Ethernet controller"
193	depends on MX5 || MX6 || MX7 || IMX8
194	help
195	  This driver supports the 10/100 Fast Ethernet controller for
196	  NXP i.MX processors.
197
198config FTMAC100
199	bool "Ftmac100 Ethernet Support"
200	help
201	  This MAC is present in Andestech SoCs.
202
203config FTGMAC100
204	bool "Ftgmac100 Ethernet Support"
205	depends on DM_ETH
206	select PHYLIB
207	help
208	  This driver supports the Faraday's FTGMAC100 Gigabit SoC
209	  Ethernet controller that can be found on Aspeed SoCs (which
210	  include NCSI).
211
212	  It is fully compliant with IEEE 802.3 specification for
213	  10/100 Mbps Ethernet and IEEE 802.3z specification for 1000
214	  Mbps Ethernet and includes Reduced Media Independent
215	  Interface (RMII) and Reduced Gigabit Media Independent
216	  Interface (RGMII) interfaces. It adopts an AHB bus interface
217	  and integrates a link list DMA engine with direct M-Bus
218	  accesses for transmitting and receiving packets. It has
219	  independent TX/RX fifos, supports half and full duplex (1000
220	  Mbps mode only supports full duplex), flow control for full
221	  duplex and backpressure for half duplex.
222
223	  The FTGMAC100 also implements IP, TCP, UDP checksum offloads
224	  and supports IEEE 802.1Q VLAN tag insertion and removal. It
225	  offers high-priority transmit queue for QoS and CoS
226	  applications.
227
228
229config MVGBE
230	bool "Marvell Orion5x/Kirkwood network interface support"
231	depends on KIRKWOOD || ORION5X
232	select PHYLIB if DM_ETH
233	help
234	  This driver supports the network interface units in the
235	  Marvell Orion5x and Kirkwood SoCs
236
237config MVNETA
238	bool "Marvell Armada XP/385/3700 network interface support"
239	depends on ARMADA_XP || ARMADA_38X || ARMADA_3700
240	select PHYLIB
241	help
242	  This driver supports the network interface units in the
243	  Marvell ARMADA XP, ARMADA 38X and ARMADA 3700 SoCs
244
245config MVPP2
246	bool "Marvell Armada 375/7K/8K network interface support"
247	depends on ARMADA_375 || ARMADA_8K
248	select PHYLIB
249	help
250	  This driver supports the network interface units in the
251	  Marvell ARMADA 375, 7K and 8K SoCs.
252
253config MACB
254	bool "Cadence MACB/GEM Ethernet Interface"
255	depends on DM_ETH
256	select PHYLIB
257	help
258	  The Cadence MACB ethernet interface is found on many Atmel
259	  AT91 and SAMA5 parts.  This driver also supports the Cadence
260	  GEM (Gigabit Ethernet MAC) found in some ARM SoC devices.
261	  Say Y to include support for the MACB/GEM chip.
262
263config MACB_ZYNQ
264	bool "Cadence MACB/GEM Ethernet Interface for Xilinx Zynq"
265	depends on MACB
266	help
267	  The Cadence MACB ethernet interface was used on Zynq platform.
268	  Say Y to enable support for the MACB/GEM in Zynq chip.
269
270config MT7628_ETH
271	bool "MediaTek MT7628 Ethernet Interface"
272	depends on ARCH_MT7620
273	help
274	  The MediaTek MT7628 ethernet interface is used on MT7628 and
275	  MT7688 based boards.
276
277config PCH_GBE
278	bool "Intel Platform Controller Hub EG20T GMAC driver"
279	depends on DM_ETH && DM_PCI
280	select PHYLIB
281	help
282	  This MAC is present in Intel Platform Controller Hub EG20T. It
283	  supports 10/100/1000 Mbps operation.
284
285config RGMII
286	bool "Enable RGMII"
287	help
288	  Enable the support of the Reduced Gigabit Media-Independent
289	  Interface (RGMII).
290
291config MII
292	bool "Enable MII"
293	help
294	  Enable support of the Media-Independent Interface (MII)
295
296config RTL8139
297	bool "Realtek 8139 series Ethernet controller driver"
298	help
299	  This driver supports Realtek 8139 series fast ethernet family of
300	  PCI chipsets/adapters.
301
302config RTL8169
303	bool "Realtek 8169 series Ethernet controller driver"
304	help
305	  This driver supports Realtek 8169 series gigabit ethernet family of
306	  PCI/PCIe chipsets/adapters.
307
308config SMC911X
309	bool "SMSC LAN911x and LAN921x controller driver"
310
311if SMC911X
312
313config SMC911X_BASE
314	hex "SMC911X Base Address"
315	help
316	  Define this to hold the physical address
317	  of the device (I/O space)
318
319choice
320	prompt "SMC911X bus width"
321	default SMC911X_16_BIT
322
323config SMC911X_32_BIT
324	bool "Enable 32-bit interface"
325
326config SMC911X_16_BIT
327	bool "Enable 16-bit interface"
328	help
329	  Define this if data bus is 16 bits. If your processor
330	  automatically converts one 32 bit word to two 16 bit
331	  words you may also try CONFIG_SMC911X_32_BIT.
332
333endchoice
334endif #SMC911X
335
336config SUN7I_GMAC
337	bool "Enable Allwinner GMAC Ethernet support"
338	help
339	  Enable the support for Sun7i GMAC Ethernet controller
340
341config SUN7I_GMAC_FORCE_TXERR
342	bool "Force PA17 as gmac function"
343	depends on SUN7I_GMAC
344	help
345	  Some ethernet phys needs TXERR control. Since the GMAC
346	  doesn't have such signal, setting PA17 as GMAC function
347	  makes the pin output low, which enables data transmission.
348
349config SUN4I_EMAC
350	bool "Allwinner Sun4i Ethernet MAC support"
351	depends on DM_ETH
352	select PHYLIB
353	help
354	  This driver supports the Allwinner based SUN4I Ethernet MAC.
355
356config SUN8I_EMAC
357        bool "Allwinner Sun8i Ethernet MAC support"
358        depends on DM_ETH
359        select PHYLIB
360	select PHY_GIGE
361        help
362          This driver supports the  Allwinner based SUN8I/SUN50I Ethernet MAC.
363	  It can be found in H3/A64/A83T based SoCs and compatible with both
364	  External and Internal PHYs.
365
366config SH_ETHER
367	bool "Renesas SH Ethernet MAC"
368	select PHYLIB
369	help
370	  This driver supports the Ethernet for Renesas SH and ARM SoCs.
371
372source "drivers/net/ti/Kconfig"
373
374config XILINX_AXIEMAC
375	depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP)
376	select PHYLIB
377	select MII
378	bool "Xilinx AXI Ethernet"
379	help
380	  This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs.
381
382config XILINX_EMACLITE
383	depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP || MIPS)
384	select PHYLIB
385	select MII
386	bool "Xilinx Ethernetlite"
387	help
388	  This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs.
389
390config ZYNQ_GEM
391	depends on DM_ETH && (ARCH_ZYNQ || ARCH_ZYNQMP || ARCH_VERSAL)
392	select PHYLIB
393	bool "Xilinx Ethernet GEM"
394	help
395	  This MAC is present in Xilinx Zynq and ZynqMP SoCs.
396
397config PIC32_ETH
398	bool "Microchip PIC32 Ethernet Support"
399	depends on DM_ETH && MACH_PIC32
400	select PHYLIB
401	help
402	  This driver implements 10/100 Mbps Ethernet and MAC layer for
403	  Microchip PIC32 microcontrollers.
404
405config GMAC_ROCKCHIP
406	bool "Rockchip Synopsys Designware Ethernet MAC"
407	depends on DM_ETH && ETH_DESIGNWARE
408	help
409	  This driver provides Rockchip SoCs network support based on the
410	  Synopsys Designware driver.
411
412config RENESAS_RAVB
413	bool "Renesas Ethernet AVB MAC"
414	depends on DM_ETH && RCAR_GEN3
415	select PHYLIB
416	help
417	  This driver implements support for the Ethernet AVB block in
418	  Renesas M3 and H3 SoCs.
419
420config MPC8XX_FEC
421	bool "Fast Ethernet Controller on MPC8XX"
422	depends on MPC8xx
423	select MII
424	help
425	  This driver implements support for the Fast Ethernet Controller
426	  on MPC8XX
427
428config SNI_AVE
429	bool "Socionext AVE Ethernet support"
430	depends on DM_ETH && ARCH_UNIPHIER
431	select PHYLIB
432	select SYSCON
433	select REGMAP
434	help
435	  This driver implements support for the Socionext AVE Ethernet
436	  controller, as found on the Socionext UniPhier family.
437
438source "drivers/net/mscc_eswitch/Kconfig"
439
440config ETHER_ON_FEC1
441	bool "FEC1"
442	depends on MPC8XX_FEC
443	default y
444
445config FEC1_PHY
446	int "FEC1 PHY"
447	depends on ETHER_ON_FEC1
448	default -1
449	help
450	  Define to the hardcoded PHY address which corresponds
451	  to the given FEC; i. e.
452		#define CONFIG_FEC1_PHY 4
453	  means that the PHY with address 4 is connected to FEC1
454
455	  When set to -1, means to probe for first available.
456
457config PHY_NORXERR
458	bool "PHY_NORXERR"
459	depends on ETHER_ON_FEC1
460	default n
461	help
462	  The PHY does not have a RXERR line (RMII only).
463	  (so program the FEC to ignore it).
464
465config ETHER_ON_FEC2
466	bool "FEC2"
467	depends on MPC8XX_FEC && MPC885
468	default y
469
470config FEC2_PHY
471	int "FEC2 PHY"
472	depends on ETHER_ON_FEC2
473	default -1
474	help
475	  Define to the hardcoded PHY address which corresponds
476	  to the given FEC; i. e.
477		#define CONFIG_FEC1_PHY 4
478	  means that the PHY with address 4 is connected to FEC1
479
480	  When set to -1, means to probe for first available.
481
482config FEC2_PHY_NORXERR
483	bool "PHY_NORXERR"
484	depends on ETHER_ON_FEC2
485	default n
486	help
487	  The PHY does not have a RXERR line (RMII only).
488	  (so program the FEC to ignore it).
489
490config SYS_DPAA_QBMAN
491	bool "Device tree fixup for QBMan on freescale SOCs"
492	depends on (ARM || PPC) && !SPL_BUILD
493	default y if ARCH_B4860 || \
494		     ARCH_B4420 || \
495		     ARCH_P1023 || \
496		     ARCH_P2041 || \
497		     ARCH_T1023 || \
498		     ARCH_T1024 || \
499		     ARCH_T1040 || \
500		     ARCH_T1042 || \
501		     ARCH_T2080 || \
502		     ARCH_T2081 || \
503		     ARCH_T4240 || \
504		     ARCH_T4160 || \
505		     ARCH_P4080 || \
506		     ARCH_P3041 || \
507		     ARCH_P5040 || \
508		     ARCH_P5020 || \
509		     ARCH_LS1043A || \
510		     ARCH_LS1046A
511	help
512	  QBman fixups to allow deep sleep in DPAA 1 SOCs
513
514config TSEC_ENET
515	select PHYLIB
516	bool "Enable Three-Speed Ethernet Controller"
517	help
518	  This driver implements support for the (Enhanced) Three-Speed
519	  Ethernet Controller found on Freescale SoCs.
520
521config MEDIATEK_ETH
522	bool "MediaTek Ethernet GMAC Driver"
523	depends on DM_ETH
524	select PHYLIB
525	select DM_GPIO
526	select DM_RESET
527	help
528	  This Driver support MediaTek Ethernet GMAC
529	  Say Y to enable support for the MediaTek Ethernet GMAC.
530
531endif # NETDEVICES
532