xref: /openbmc/u-boot/drivers/net/Kconfig (revision c74dda8b) 
1source "drivers/net/phy/Kconfig"
2
3config DM_ETH
4	bool "Enable Driver Model for Ethernet drivers"
5	depends on DM
6	help
7	  Enable driver model for Ethernet.
8
9	  The eth_*() interface will be implemented by the UC_ETH class
10	  This is currently implemented in net/eth.c
11	  Look in include/net.h for details.
12
13menuconfig NETDEVICES
14	bool "Network device support"
15	depends on NET
16	default y if DM_ETH
17	help
18	  You must select Y to enable any network device support
19	  Generally if you have any networking support this is a given
20
21	  If unsure, say Y
22
23if NETDEVICES
24
25config PHY_GIGE
26	bool "Enable GbE PHY status parsing and configuration"
27	help
28	  Enables support for parsing the status output and for
29	  configuring GbE PHYs (affects the inner workings of some
30	  commands and miiphyutil.c).
31
32config AG7XXX
33	bool "Atheros AG7xxx Ethernet MAC support"
34	depends on DM_ETH && ARCH_ATH79
35	select PHYLIB
36	help
37	  This driver supports the Atheros AG7xxx Ethernet MAC. This MAC is
38	  present in the Atheros AR7xxx, AR9xxx and QCA9xxx MIPS chips.
39
40
41config ALTERA_TSE
42	bool "Altera Triple-Speed Ethernet MAC support"
43	depends on DM_ETH
44	select PHYLIB
45	help
46	  This driver supports the Altera Triple-Speed (TSE) Ethernet MAC.
47	  Please find details on the "Triple-Speed Ethernet MegaCore Function
48	  Resource Center" of Altera.
49
50config BCM_SF2_ETH
51	bool "Broadcom SF2 (Starfighter2) Ethernet support"
52	select PHYLIB
53	help
54	  This is an abstract framework which provides a generic interface
55	  to MAC and DMA management for multiple Broadcom SoCs such as
56	  Cygnus, NSP and bcm28155_ap platforms.
57
58config BCM_SF2_ETH_DEFAULT_PORT
59	int "Broadcom SF2 (Starfighter2) Ethernet default port number"
60	depends on BCM_SF2_ETH
61	default 0
62	help
63	  Default port number for the Starfighter2 ethernet driver.
64
65config BCM_SF2_ETH_GMAC
66	bool "Broadcom SF2 (Starfighter2) GMAC Ethernet support"
67	depends on BCM_SF2_ETH
68	help
69	  This flag enables the ethernet support for Broadcom platforms with
70	  GMAC such as Cygnus. This driver is based on the framework provided
71	  by the BCM_SF2_ETH driver.
72	  Say Y to any bcmcygnus based platforms.
73
74config DWC_ETH_QOS
75	bool "Synopsys DWC Ethernet QOS device support"
76	depends on DM_ETH
77	select PHYLIB
78	help
79	  This driver supports the Synopsys Designware Ethernet QOS (Quality
80	  Of Service) IP block. The IP supports many options for bus type,
81	  clocking/reset structure, and feature list. This driver currently
82	  supports the specific configuration used in NVIDIA's Tegra186 chip,
83	  but should be extensible to other combinations quite easily.
84
85config E1000
86	bool "Intel PRO/1000 Gigabit Ethernet support"
87	help
88	  This driver supports Intel(R) PRO/1000 gigabit ethernet family of
89	  adapters.  For more information on how to identify your adapter, go
90	  to the Adapter & Driver ID Guide at:
91
92	  <http://support.intel.com/support/network/adapter/pro100/21397.htm>
93
94config E1000_SPI_GENERIC
95	bool "Allow access to the Intel 8257x SPI bus"
96	depends on E1000
97	help
98	  Allow generic access to the SPI bus on the Intel 8257x, for
99	  example with the "sspi" command.
100
101config E1000_SPI
102	bool "Enable SPI bus utility code"
103	depends on E1000
104	help
105	  Utility code for direct access to the SPI bus on Intel 8257x.
106	  This does not do anything useful unless you set at least one
107	  of CONFIG_CMD_E1000 or CONFIG_E1000_SPI_GENERIC.
108
109config CMD_E1000
110	bool "Enable the e1000 command"
111	depends on E1000
112	help
113	  This enables the 'e1000' management command for E1000 devices. When
114	  used on devices with SPI support you can reprogram the EEPROM from
115	  U-Boot.
116
117config ETH_SANDBOX
118	depends on DM_ETH && SANDBOX
119	default y
120	bool "Sandbox: Mocked Ethernet driver"
121	help
122	  This driver simply responds with fake ARP replies and ping
123	  replies that are used to verify network stack functionality
124
125	  This driver is particularly useful in the test/dm/eth.c tests
126
127config ETH_SANDBOX_RAW
128	depends on DM_ETH && SANDBOX
129	default y
130	bool "Sandbox: Bridge to Linux Raw Sockets"
131	help
132	  This driver is a bridge from the bottom of the network stack
133	  in U-Boot to the RAW AF_PACKET API in Linux. This allows real
134	  network traffic to be tested from within sandbox. See
135	  board/sandbox/README.sandbox for more details.
136
137config ETH_DESIGNWARE
138	bool "Synopsys Designware Ethernet MAC"
139	select PHYLIB
140	help
141	  This MAC is present in SoCs from various vendors. It supports
142	  100Mbit and 1 Gbit operation. You must enable CONFIG_PHYLIB to
143	  provide the PHY (physical media interface).
144
145config ETHOC
146	bool "OpenCores 10/100 Mbps Ethernet MAC"
147	help
148	  This MAC is present in OpenRISC and Xtensa XTFPGA boards.
149
150config FEC_MXC
151	bool "FEC Ethernet controller"
152	depends on MX5 || MX6
153	help
154	  This driver supports the 10/100 Fast Ethernet controller for
155	  NXP i.MX processors.
156
157config FTMAC100
158	bool "Ftmac100 Ethernet Support"
159	help
160	  This MAC is present in Andestech SoCs.
161
162config MVPP2
163	bool "Marvell Armada 375/7K/8K network interface support"
164	depends on ARMADA_375 || ARMADA_8K
165	select PHYLIB
166	help
167	  This driver supports the network interface units in the
168	  Marvell ARMADA 375, 7K and 8K SoCs.
169
170config MACB
171	bool "Cadence MACB/GEM Ethernet Interface"
172	depends on DM_ETH
173	select PHYLIB
174	help
175	  The Cadence MACB ethernet interface is found on many Atmel
176	  AT91 and SAMA5 parts.  This driver also supports the Cadence
177	  GEM (Gigabit Ethernet MAC) found in some ARM SoC devices.
178	  Say Y to include support for the MACB/GEM chip.
179
180config PCH_GBE
181	bool "Intel Platform Controller Hub EG20T GMAC driver"
182	depends on DM_ETH && DM_PCI
183	select PHYLIB
184	help
185	  This MAC is present in Intel Platform Controller Hub EG20T. It
186	  supports 10/100/1000 Mbps operation.
187
188config RGMII
189	bool "Enable RGMII"
190	help
191	  Enable the support of the Reduced Gigabit Media-Independent
192	  Interface (RGMII).
193
194config RTL8139
195	bool "Realtek 8139 series Ethernet controller driver"
196	help
197	  This driver supports Realtek 8139 series fast ethernet family of
198	  PCI chipsets/adapters.
199
200config RTL8169
201	bool "Realtek 8169 series Ethernet controller driver"
202	help
203	  This driver supports Realtek 8169 series gigabit ethernet family of
204	  PCI/PCIe chipsets/adapters.
205
206config SUN7I_GMAC
207	bool "Enable Allwinner GMAC Ethernet support"
208	help
209	  Enable the support for Sun7i GMAC Ethernet controller
210
211config SUN4I_EMAC
212	bool "Allwinner Sun4i Ethernet MAC support"
213	depends on DM_ETH
214	help
215	  This driver supports the Allwinner based SUN4I Ethernet MAC.
216
217config SUN8I_EMAC
218        bool "Allwinner Sun8i Ethernet MAC support"
219        depends on DM_ETH
220        select PHYLIB
221	select PHY_GIGE
222        help
223          This driver supports the  Allwinner based SUN8I/SUN50I Ethernet MAC.
224	  It can be found in H3/A64/A83T based SoCs and compatible with both
225	  External and Internal PHYs.
226
227config XILINX_AXIEMAC
228	depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP)
229	select PHYLIB
230	select MII
231	bool "Xilinx AXI Ethernet"
232	help
233	  This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs.
234
235config XILINX_EMACLITE
236	depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP || MIPS)
237	select PHYLIB
238	select MII
239	bool "Xilinx Ethernetlite"
240	help
241	  This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs.
242
243config ZYNQ_GEM
244	depends on DM_ETH && (ARCH_ZYNQ || ARCH_ZYNQMP)
245	select PHYLIB
246	bool "Xilinx Ethernet GEM"
247	help
248	  This MAC is present in Xilinx Zynq and ZynqMP SoCs.
249
250config PIC32_ETH
251	bool "Microchip PIC32 Ethernet Support"
252	depends on DM_ETH && MACH_PIC32
253	select PHYLIB
254	help
255	  This driver implements 10/100 Mbps Ethernet and MAC layer for
256	  Microchip PIC32 microcontrollers.
257
258config GMAC_ROCKCHIP
259	bool "Rockchip Synopsys Designware Ethernet MAC"
260	depends on DM_ETH && ETH_DESIGNWARE
261	help
262	  This driver provides Rockchip SoCs network support based on the
263	  Synopsys Designware driver.
264
265config RENESAS_RAVB
266	bool "Renesas Ethernet AVB MAC"
267	depends on DM_ETH && RCAR_GEN3
268	select PHYLIB
269	help
270	  This driver implements support for the Ethernet AVB block in
271	  Renesas M3 and H3 SoCs.
272
273config MPC8XX_FEC
274	bool "Fast Ethernet Controller on MPC8XX"
275	depends on 8xx
276	select MII
277	help
278	  This driver implements support for the Fast Ethernet Controller
279	  on MPC8XX
280
281config ETHER_ON_FEC1
282	bool "FEC1"
283	depends on MPC8XX_FEC
284	default y
285
286config FEC1_PHY
287	int "FEC1 PHY"
288	depends on ETHER_ON_FEC1
289	default -1
290	help
291	  Define to the hardcoded PHY address which corresponds
292	  to the given FEC; i. e.
293		#define CONFIG_FEC1_PHY 4
294	  means that the PHY with address 4 is connected to FEC1
295
296	  When set to -1, means to probe for first available.
297
298config PHY_NORXERR
299	bool "PHY_NORXERR"
300	depends on ETHER_ON_FEC1
301	default n
302	help
303	  The PHY does not have a RXERR line (RMII only).
304	  (so program the FEC to ignore it).
305
306config ETHER_ON_FEC2
307	bool "FEC2"
308	depends on MPC8XX_FEC && MPC885
309	default y
310
311config FEC2_PHY
312	int "FEC2 PHY"
313	depends on ETHER_ON_FEC2
314	default -1
315	help
316	  Define to the hardcoded PHY address which corresponds
317	  to the given FEC; i. e.
318		#define CONFIG_FEC1_PHY 4
319	  means that the PHY with address 4 is connected to FEC1
320
321	  When set to -1, means to probe for first available.
322
323config FEC2_PHY_NORXERR
324	bool "PHY_NORXERR"
325	depends on ETHER_ON_FEC2
326	default n
327	help
328	  The PHY does not have a RXERR line (RMII only).
329	  (so program the FEC to ignore it).
330
331endif # NETDEVICES
332