xref: /openbmc/u-boot/drivers/net/Kconfig (revision b2153075)
1source "drivers/net/phy/Kconfig"
2
3config DM_ETH
4	bool "Enable Driver Model for Ethernet drivers"
5	depends on DM
6	help
7	  Enable driver model for Ethernet.
8
9	  The eth_*() interface will be implemented by the UC_ETH class
10	  This is currently implemented in net/eth.c
11	  Look in include/net.h for details.
12
13menuconfig NETDEVICES
14	bool "Network device support"
15	depends on NET
16	default y if DM_ETH
17	help
18	  You must select Y to enable any network device support
19	  Generally if you have any networking support this is a given
20
21	  If unsure, say Y
22
23if NETDEVICES
24
25config PHY_GIGE
26	bool "Enable GbE PHY status parsing and configuration"
27	help
28	  Enables support for parsing the status output and for
29	  configuring GbE PHYs (affects the inner workings of some
30	  commands and miiphyutil.c).
31
32config AG7XXX
33	bool "Atheros AG7xxx Ethernet MAC support"
34	depends on DM_ETH && ARCH_ATH79
35	select PHYLIB
36	help
37	  This driver supports the Atheros AG7xxx Ethernet MAC. This MAC is
38	  present in the Atheros AR7xxx, AR9xxx and QCA9xxx MIPS chips.
39
40
41config ALTERA_TSE
42	bool "Altera Triple-Speed Ethernet MAC support"
43	depends on DM_ETH
44	select PHYLIB
45	help
46	  This driver supports the Altera Triple-Speed (TSE) Ethernet MAC.
47	  Please find details on the "Triple-Speed Ethernet MegaCore Function
48	  Resource Center" of Altera.
49
50config BCM_SF2_ETH
51	bool "Broadcom SF2 (Starfighter2) Ethernet support"
52	select PHYLIB
53	help
54	  This is an abstract framework which provides a generic interface
55	  to MAC and DMA management for multiple Broadcom SoCs such as
56	  Cygnus, NSP and bcm28155_ap platforms.
57
58config BCM_SF2_ETH_DEFAULT_PORT
59	int "Broadcom SF2 (Starfighter2) Ethernet default port number"
60	depends on BCM_SF2_ETH
61	default 0
62	help
63	  Default port number for the Starfighter2 ethernet driver.
64
65config BCM_SF2_ETH_GMAC
66	bool "Broadcom SF2 (Starfighter2) GMAC Ethernet support"
67	depends on BCM_SF2_ETH
68	help
69	  This flag enables the ethernet support for Broadcom platforms with
70	  GMAC such as Cygnus. This driver is based on the framework provided
71	  by the BCM_SF2_ETH driver.
72	  Say Y to any bcmcygnus based platforms.
73
74config DWC_ETH_QOS
75	bool "Synopsys DWC Ethernet QOS device support"
76	depends on DM_ETH
77	select PHYLIB
78	help
79	  This driver supports the Synopsys Designware Ethernet QOS (Quality
80	  Of Service) IP block. The IP supports many options for bus type,
81	  clocking/reset structure, and feature list. This driver currently
82	  supports the specific configuration used in NVIDIA's Tegra186 chip,
83	  but should be extensible to other combinations quite easily.
84
85config E1000
86	bool "Intel PRO/1000 Gigabit Ethernet support"
87	help
88	  This driver supports Intel(R) PRO/1000 gigabit ethernet family of
89	  adapters.  For more information on how to identify your adapter, go
90	  to the Adapter & Driver ID Guide at:
91
92	  <http://support.intel.com/support/network/adapter/pro100/21397.htm>
93
94config E1000_SPI_GENERIC
95	bool "Allow access to the Intel 8257x SPI bus"
96	depends on E1000
97	help
98	  Allow generic access to the SPI bus on the Intel 8257x, for
99	  example with the "sspi" command.
100
101config E1000_SPI
102	bool "Enable SPI bus utility code"
103	depends on E1000
104	help
105	  Utility code for direct access to the SPI bus on Intel 8257x.
106	  This does not do anything useful unless you set at least one
107	  of CONFIG_CMD_E1000 or CONFIG_E1000_SPI_GENERIC.
108
109config CMD_E1000
110	bool "Enable the e1000 command"
111	depends on E1000
112	help
113	  This enables the 'e1000' management command for E1000 devices. When
114	  used on devices with SPI support you can reprogram the EEPROM from
115	  U-Boot.
116
117config ETH_SANDBOX
118	depends on DM_ETH && SANDBOX
119	default y
120	bool "Sandbox: Mocked Ethernet driver"
121	help
122	  This driver simply responds with fake ARP replies and ping
123	  replies that are used to verify network stack functionality
124
125	  This driver is particularly useful in the test/dm/eth.c tests
126
127config ETH_SANDBOX_RAW
128	depends on DM_ETH && SANDBOX
129	default y
130	bool "Sandbox: Bridge to Linux Raw Sockets"
131	help
132	  This driver is a bridge from the bottom of the network stack
133	  in U-Boot to the RAW AF_PACKET API in Linux. This allows real
134	  network traffic to be tested from within sandbox. See
135	  board/sandbox/README.sandbox for more details.
136
137config ETH_DESIGNWARE
138	bool "Synopsys Designware Ethernet MAC"
139	select PHYLIB
140	help
141	  This MAC is present in SoCs from various vendors. It supports
142	  100Mbit and 1 Gbit operation. You must enable CONFIG_PHYLIB to
143	  provide the PHY (physical media interface).
144
145config ETHOC
146	bool "OpenCores 10/100 Mbps Ethernet MAC"
147	help
148	  This MAC is present in OpenRISC and Xtensa XTFPGA boards.
149
150config FEC_MXC
151	bool "FEC Ethernet controller"
152	depends on MX5 || MX6
153	help
154	  This driver supports the 10/100 Fast Ethernet controller for
155	  NXP i.MX processors.
156
157config FTMAC100
158	bool "Ftmac100 Ethernet Support"
159	help
160	  This MAC is present in Andestech SoCs.
161
162config MVNETA
163	bool "Marvell Armada XP/385/3700 network interface support"
164	depends on ARMADA_XP || ARMADA_38X || ARMADA_3700
165	select PHYLIB
166	help
167	  This driver supports the network interface units in the
168	  Marvell ARMADA XP, ARMADA 38X and ARMADA 3700 SoCs
169
170config MVPP2
171	bool "Marvell Armada 375/7K/8K network interface support"
172	depends on ARMADA_375 || ARMADA_8K
173	select PHYLIB
174	help
175	  This driver supports the network interface units in the
176	  Marvell ARMADA 375, 7K and 8K SoCs.
177
178config MACB
179	bool "Cadence MACB/GEM Ethernet Interface"
180	depends on DM_ETH
181	select PHYLIB
182	help
183	  The Cadence MACB ethernet interface is found on many Atmel
184	  AT91 and SAMA5 parts.  This driver also supports the Cadence
185	  GEM (Gigabit Ethernet MAC) found in some ARM SoC devices.
186	  Say Y to include support for the MACB/GEM chip.
187
188config MACB_ZYNQ
189	bool "Cadence MACB/GEM Ethernet Interface for Xilinx Zynq"
190	depends on MACB
191	help
192	  The Cadence MACB ethernet interface was used on Zynq platform.
193	  Say Y to enable support for the MACB/GEM in Zynq chip.
194
195config PCH_GBE
196	bool "Intel Platform Controller Hub EG20T GMAC driver"
197	depends on DM_ETH && DM_PCI
198	select PHYLIB
199	help
200	  This MAC is present in Intel Platform Controller Hub EG20T. It
201	  supports 10/100/1000 Mbps operation.
202
203config RGMII
204	bool "Enable RGMII"
205	help
206	  Enable the support of the Reduced Gigabit Media-Independent
207	  Interface (RGMII).
208
209config RTL8139
210	bool "Realtek 8139 series Ethernet controller driver"
211	help
212	  This driver supports Realtek 8139 series fast ethernet family of
213	  PCI chipsets/adapters.
214
215config RTL8169
216	bool "Realtek 8169 series Ethernet controller driver"
217	help
218	  This driver supports Realtek 8169 series gigabit ethernet family of
219	  PCI/PCIe chipsets/adapters.
220
221config SMC911X
222	bool "SMSC LAN911x and LAN921x controller driver"
223
224if SMC911X
225
226config SMC911X_BASE
227	hex "SMC911X Base Address"
228	help
229	  Define this to hold the physical address
230	  of the device (I/O space)
231
232choice
233	prompt "SMC911X bus width"
234	default SMC911X_16_BIT
235
236config SMC911X_32_BIT
237	bool "Enable 32-bit interface"
238
239config SMC911X_16_BIT
240	bool "Enable 16-bit interface"
241	help
242	  Define this if data bus is 16 bits. If your processor
243	  automatically converts one 32 bit word to two 16 bit
244	  words you may also try CONFIG_SMC911X_32_BIT.
245
246endchoice
247endif #SMC911X
248
249config SUN7I_GMAC
250	bool "Enable Allwinner GMAC Ethernet support"
251	help
252	  Enable the support for Sun7i GMAC Ethernet controller
253
254config SUN7I_GMAC_FORCE_TXERR
255	bool "Force PA17 as gmac function"
256	depends on SUN7I_GMAC
257	help
258	  Some ethernet phys needs TXERR control. Since the GMAC
259	  doesn't have such signal, setting PA17 as GMAC function
260	  makes the pin output low, which enables data transmission.
261
262config SUN4I_EMAC
263	bool "Allwinner Sun4i Ethernet MAC support"
264	depends on DM_ETH
265	select PHYLIB
266	help
267	  This driver supports the Allwinner based SUN4I Ethernet MAC.
268
269config SUN8I_EMAC
270        bool "Allwinner Sun8i Ethernet MAC support"
271        depends on DM_ETH
272        select PHYLIB
273	select PHY_GIGE
274        help
275          This driver supports the  Allwinner based SUN8I/SUN50I Ethernet MAC.
276	  It can be found in H3/A64/A83T based SoCs and compatible with both
277	  External and Internal PHYs.
278
279config SH_ETHER
280	bool "Renesas SH Ethernet MAC"
281	select PHYLIB
282	help
283	  This driver supports the Ethernet for Renesas SH and ARM SoCs.
284
285config XILINX_AXIEMAC
286	depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP)
287	select PHYLIB
288	select MII
289	bool "Xilinx AXI Ethernet"
290	help
291	  This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs.
292
293config XILINX_EMACLITE
294	depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP || MIPS)
295	select PHYLIB
296	select MII
297	bool "Xilinx Ethernetlite"
298	help
299	  This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs.
300
301config ZYNQ_GEM
302	depends on DM_ETH && (ARCH_ZYNQ || ARCH_ZYNQMP)
303	select PHYLIB
304	bool "Xilinx Ethernet GEM"
305	help
306	  This MAC is present in Xilinx Zynq and ZynqMP SoCs.
307
308config PIC32_ETH
309	bool "Microchip PIC32 Ethernet Support"
310	depends on DM_ETH && MACH_PIC32
311	select PHYLIB
312	help
313	  This driver implements 10/100 Mbps Ethernet and MAC layer for
314	  Microchip PIC32 microcontrollers.
315
316config GMAC_ROCKCHIP
317	bool "Rockchip Synopsys Designware Ethernet MAC"
318	depends on DM_ETH && ETH_DESIGNWARE
319	help
320	  This driver provides Rockchip SoCs network support based on the
321	  Synopsys Designware driver.
322
323config RENESAS_RAVB
324	bool "Renesas Ethernet AVB MAC"
325	depends on DM_ETH && RCAR_GEN3
326	select PHYLIB
327	help
328	  This driver implements support for the Ethernet AVB block in
329	  Renesas M3 and H3 SoCs.
330
331config MPC8XX_FEC
332	bool "Fast Ethernet Controller on MPC8XX"
333	depends on 8xx
334	select MII
335	help
336	  This driver implements support for the Fast Ethernet Controller
337	  on MPC8XX
338
339config ETHER_ON_FEC1
340	bool "FEC1"
341	depends on MPC8XX_FEC
342	default y
343
344config FEC1_PHY
345	int "FEC1 PHY"
346	depends on ETHER_ON_FEC1
347	default -1
348	help
349	  Define to the hardcoded PHY address which corresponds
350	  to the given FEC; i. e.
351		#define CONFIG_FEC1_PHY 4
352	  means that the PHY with address 4 is connected to FEC1
353
354	  When set to -1, means to probe for first available.
355
356config PHY_NORXERR
357	bool "PHY_NORXERR"
358	depends on ETHER_ON_FEC1
359	default n
360	help
361	  The PHY does not have a RXERR line (RMII only).
362	  (so program the FEC to ignore it).
363
364config ETHER_ON_FEC2
365	bool "FEC2"
366	depends on MPC8XX_FEC && MPC885
367	default y
368
369config FEC2_PHY
370	int "FEC2 PHY"
371	depends on ETHER_ON_FEC2
372	default -1
373	help
374	  Define to the hardcoded PHY address which corresponds
375	  to the given FEC; i. e.
376		#define CONFIG_FEC1_PHY 4
377	  means that the PHY with address 4 is connected to FEC1
378
379	  When set to -1, means to probe for first available.
380
381config FEC2_PHY_NORXERR
382	bool "PHY_NORXERR"
383	depends on ETHER_ON_FEC2
384	default n
385	help
386	  The PHY does not have a RXERR line (RMII only).
387	  (so program the FEC to ignore it).
388
389config SYS_DPAA_QBMAN
390	bool "Device tree fixup for QBMan on freescale SOCs"
391	depends on (ARM || PPC) && !SPL_BUILD
392	default y if ARCH_B4860 || \
393		     ARCH_B4420 || \
394		     ARCH_P1023 || \
395		     ARCH_P2041 || \
396		     ARCH_T1023 || \
397		     ARCH_T1024 || \
398		     ARCH_T1040 || \
399		     ARCH_T1042 || \
400		     ARCH_T2080 || \
401		     ARCH_T2081 || \
402		     ARCH_T4240 || \
403		     ARCH_T4160 || \
404		     ARCH_P4080 || \
405		     ARCH_P3041 || \
406		     ARCH_P5040 || \
407		     ARCH_P5020 || \
408		     ARCH_LS1043A || \
409		     ARCH_LS1046A
410	help
411	  QBman fixups to allow deep sleep in DPAA 1 SOCs
412
413endif # NETDEVICES
414