xref: /openbmc/u-boot/drivers/net/Kconfig (revision 704744f8)
1source "drivers/net/phy/Kconfig"
2source "drivers/net/pfe_eth/Kconfig"
3
4config DM_ETH
5	bool "Enable Driver Model for Ethernet drivers"
6	depends on DM
7	help
8	  Enable driver model for Ethernet.
9
10	  The eth_*() interface will be implemented by the UC_ETH class
11	  This is currently implemented in net/eth.c
12	  Look in include/net.h for details.
13
14menuconfig NETDEVICES
15	bool "Network device support"
16	depends on NET
17	default y if DM_ETH
18	help
19	  You must select Y to enable any network device support
20	  Generally if you have any networking support this is a given
21
22	  If unsure, say Y
23
24if NETDEVICES
25
26config PHY_GIGE
27	bool "Enable GbE PHY status parsing and configuration"
28	help
29	  Enables support for parsing the status output and for
30	  configuring GbE PHYs (affects the inner workings of some
31	  commands and miiphyutil.c).
32
33config AG7XXX
34	bool "Atheros AG7xxx Ethernet MAC support"
35	depends on DM_ETH && ARCH_ATH79
36	select PHYLIB
37	help
38	  This driver supports the Atheros AG7xxx Ethernet MAC. This MAC is
39	  present in the Atheros AR7xxx, AR9xxx and QCA9xxx MIPS chips.
40
41
42config ALTERA_TSE
43	bool "Altera Triple-Speed Ethernet MAC support"
44	depends on DM_ETH
45	select PHYLIB
46	help
47	  This driver supports the Altera Triple-Speed (TSE) Ethernet MAC.
48	  Please find details on the "Triple-Speed Ethernet MegaCore Function
49	  Resource Center" of Altera.
50
51config BCM_SF2_ETH
52	bool "Broadcom SF2 (Starfighter2) Ethernet support"
53	select PHYLIB
54	help
55	  This is an abstract framework which provides a generic interface
56	  to MAC and DMA management for multiple Broadcom SoCs such as
57	  Cygnus, NSP and bcm28155_ap platforms.
58
59config BCM_SF2_ETH_DEFAULT_PORT
60	int "Broadcom SF2 (Starfighter2) Ethernet default port number"
61	depends on BCM_SF2_ETH
62	default 0
63	help
64	  Default port number for the Starfighter2 ethernet driver.
65
66config BCM_SF2_ETH_GMAC
67	bool "Broadcom SF2 (Starfighter2) GMAC Ethernet support"
68	depends on BCM_SF2_ETH
69	help
70	  This flag enables the ethernet support for Broadcom platforms with
71	  GMAC such as Cygnus. This driver is based on the framework provided
72	  by the BCM_SF2_ETH driver.
73	  Say Y to any bcmcygnus based platforms.
74
75config DWC_ETH_QOS
76	bool "Synopsys DWC Ethernet QOS device support"
77	depends on DM_ETH
78	select PHYLIB
79	help
80	  This driver supports the Synopsys Designware Ethernet QOS (Quality
81	  Of Service) IP block. The IP supports many options for bus type,
82	  clocking/reset structure, and feature list. This driver currently
83	  supports the specific configuration used in NVIDIA's Tegra186 chip,
84	  but should be extensible to other combinations quite easily.
85
86config E1000
87	bool "Intel PRO/1000 Gigabit Ethernet support"
88	help
89	  This driver supports Intel(R) PRO/1000 gigabit ethernet family of
90	  adapters.  For more information on how to identify your adapter, go
91	  to the Adapter & Driver ID Guide at:
92
93	  <http://support.intel.com/support/network/adapter/pro100/21397.htm>
94
95config E1000_SPI_GENERIC
96	bool "Allow access to the Intel 8257x SPI bus"
97	depends on E1000
98	help
99	  Allow generic access to the SPI bus on the Intel 8257x, for
100	  example with the "sspi" command.
101
102config E1000_SPI
103	bool "Enable SPI bus utility code"
104	depends on E1000
105	help
106	  Utility code for direct access to the SPI bus on Intel 8257x.
107	  This does not do anything useful unless you set at least one
108	  of CONFIG_CMD_E1000 or CONFIG_E1000_SPI_GENERIC.
109
110config CMD_E1000
111	bool "Enable the e1000 command"
112	depends on E1000
113	help
114	  This enables the 'e1000' management command for E1000 devices. When
115	  used on devices with SPI support you can reprogram the EEPROM from
116	  U-Boot.
117
118config ETH_SANDBOX
119	depends on DM_ETH && SANDBOX
120	default y
121	bool "Sandbox: Mocked Ethernet driver"
122	help
123	  This driver simply responds with fake ARP replies and ping
124	  replies that are used to verify network stack functionality
125
126	  This driver is particularly useful in the test/dm/eth.c tests
127
128config ETH_SANDBOX_RAW
129	depends on DM_ETH && SANDBOX
130	default y
131	bool "Sandbox: Bridge to Linux Raw Sockets"
132	help
133	  This driver is a bridge from the bottom of the network stack
134	  in U-Boot to the RAW AF_PACKET API in Linux. This allows real
135	  network traffic to be tested from within sandbox. See
136	  board/sandbox/README.sandbox for more details.
137
138config ETH_DESIGNWARE
139	bool "Synopsys Designware Ethernet MAC"
140	select PHYLIB
141	help
142	  This MAC is present in SoCs from various vendors. It supports
143	  100Mbit and 1 Gbit operation. You must enable CONFIG_PHYLIB to
144	  provide the PHY (physical media interface).
145
146config ETHOC
147	bool "OpenCores 10/100 Mbps Ethernet MAC"
148	help
149	  This MAC is present in OpenRISC and Xtensa XTFPGA boards.
150
151config FEC_MXC
152	bool "FEC Ethernet controller"
153	depends on MX5 || MX6
154	help
155	  This driver supports the 10/100 Fast Ethernet controller for
156	  NXP i.MX processors.
157
158config FTMAC100
159	bool "Ftmac100 Ethernet Support"
160	help
161	  This MAC is present in Andestech SoCs.
162
163config MVNETA
164	bool "Marvell Armada XP/385/3700 network interface support"
165	depends on ARMADA_XP || ARMADA_38X || ARMADA_3700
166	select PHYLIB
167	help
168	  This driver supports the network interface units in the
169	  Marvell ARMADA XP, ARMADA 38X and ARMADA 3700 SoCs
170
171config MVPP2
172	bool "Marvell Armada 375/7K/8K network interface support"
173	depends on ARMADA_375 || ARMADA_8K
174	select PHYLIB
175	help
176	  This driver supports the network interface units in the
177	  Marvell ARMADA 375, 7K and 8K SoCs.
178
179config MACB
180	bool "Cadence MACB/GEM Ethernet Interface"
181	depends on DM_ETH
182	select PHYLIB
183	help
184	  The Cadence MACB ethernet interface is found on many Atmel
185	  AT91 and SAMA5 parts.  This driver also supports the Cadence
186	  GEM (Gigabit Ethernet MAC) found in some ARM SoC devices.
187	  Say Y to include support for the MACB/GEM chip.
188
189config MACB_ZYNQ
190	bool "Cadence MACB/GEM Ethernet Interface for Xilinx Zynq"
191	depends on MACB
192	help
193	  The Cadence MACB ethernet interface was used on Zynq platform.
194	  Say Y to enable support for the MACB/GEM in Zynq chip.
195
196config PCH_GBE
197	bool "Intel Platform Controller Hub EG20T GMAC driver"
198	depends on DM_ETH && DM_PCI
199	select PHYLIB
200	help
201	  This MAC is present in Intel Platform Controller Hub EG20T. It
202	  supports 10/100/1000 Mbps operation.
203
204config RGMII
205	bool "Enable RGMII"
206	help
207	  Enable the support of the Reduced Gigabit Media-Independent
208	  Interface (RGMII).
209
210config RTL8139
211	bool "Realtek 8139 series Ethernet controller driver"
212	help
213	  This driver supports Realtek 8139 series fast ethernet family of
214	  PCI chipsets/adapters.
215
216config RTL8169
217	bool "Realtek 8169 series Ethernet controller driver"
218	help
219	  This driver supports Realtek 8169 series gigabit ethernet family of
220	  PCI/PCIe chipsets/adapters.
221
222config SMC911X
223	bool "SMSC LAN911x and LAN921x controller driver"
224
225if SMC911X
226
227config SMC911X_BASE
228	hex "SMC911X Base Address"
229	help
230	  Define this to hold the physical address
231	  of the device (I/O space)
232
233choice
234	prompt "SMC911X bus width"
235	default SMC911X_16_BIT
236
237config SMC911X_32_BIT
238	bool "Enable 32-bit interface"
239
240config SMC911X_16_BIT
241	bool "Enable 16-bit interface"
242	help
243	  Define this if data bus is 16 bits. If your processor
244	  automatically converts one 32 bit word to two 16 bit
245	  words you may also try CONFIG_SMC911X_32_BIT.
246
247endchoice
248endif #SMC911X
249
250config SUN7I_GMAC
251	bool "Enable Allwinner GMAC Ethernet support"
252	help
253	  Enable the support for Sun7i GMAC Ethernet controller
254
255config SUN7I_GMAC_FORCE_TXERR
256	bool "Force PA17 as gmac function"
257	depends on SUN7I_GMAC
258	help
259	  Some ethernet phys needs TXERR control. Since the GMAC
260	  doesn't have such signal, setting PA17 as GMAC function
261	  makes the pin output low, which enables data transmission.
262
263config SUN4I_EMAC
264	bool "Allwinner Sun4i Ethernet MAC support"
265	depends on DM_ETH
266	select PHYLIB
267	help
268	  This driver supports the Allwinner based SUN4I Ethernet MAC.
269
270config SUN8I_EMAC
271        bool "Allwinner Sun8i Ethernet MAC support"
272        depends on DM_ETH
273        select PHYLIB
274	select PHY_GIGE
275        help
276          This driver supports the  Allwinner based SUN8I/SUN50I Ethernet MAC.
277	  It can be found in H3/A64/A83T based SoCs and compatible with both
278	  External and Internal PHYs.
279
280config SH_ETHER
281	bool "Renesas SH Ethernet MAC"
282	select PHYLIB
283	help
284	  This driver supports the Ethernet for Renesas SH and ARM SoCs.
285
286config XILINX_AXIEMAC
287	depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP)
288	select PHYLIB
289	select MII
290	bool "Xilinx AXI Ethernet"
291	help
292	  This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs.
293
294config XILINX_EMACLITE
295	depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP || MIPS)
296	select PHYLIB
297	select MII
298	bool "Xilinx Ethernetlite"
299	help
300	  This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs.
301
302config ZYNQ_GEM
303	depends on DM_ETH && (ARCH_ZYNQ || ARCH_ZYNQMP)
304	select PHYLIB
305	bool "Xilinx Ethernet GEM"
306	help
307	  This MAC is present in Xilinx Zynq and ZynqMP SoCs.
308
309config PIC32_ETH
310	bool "Microchip PIC32 Ethernet Support"
311	depends on DM_ETH && MACH_PIC32
312	select PHYLIB
313	help
314	  This driver implements 10/100 Mbps Ethernet and MAC layer for
315	  Microchip PIC32 microcontrollers.
316
317config GMAC_ROCKCHIP
318	bool "Rockchip Synopsys Designware Ethernet MAC"
319	depends on DM_ETH && ETH_DESIGNWARE
320	help
321	  This driver provides Rockchip SoCs network support based on the
322	  Synopsys Designware driver.
323
324config RENESAS_RAVB
325	bool "Renesas Ethernet AVB MAC"
326	depends on DM_ETH && RCAR_GEN3
327	select PHYLIB
328	help
329	  This driver implements support for the Ethernet AVB block in
330	  Renesas M3 and H3 SoCs.
331
332config MPC8XX_FEC
333	bool "Fast Ethernet Controller on MPC8XX"
334	depends on MPC8xx
335	select MII
336	help
337	  This driver implements support for the Fast Ethernet Controller
338	  on MPC8XX
339
340config ETHER_ON_FEC1
341	bool "FEC1"
342	depends on MPC8XX_FEC
343	default y
344
345config FEC1_PHY
346	int "FEC1 PHY"
347	depends on ETHER_ON_FEC1
348	default -1
349	help
350	  Define to the hardcoded PHY address which corresponds
351	  to the given FEC; i. e.
352		#define CONFIG_FEC1_PHY 4
353	  means that the PHY with address 4 is connected to FEC1
354
355	  When set to -1, means to probe for first available.
356
357config PHY_NORXERR
358	bool "PHY_NORXERR"
359	depends on ETHER_ON_FEC1
360	default n
361	help
362	  The PHY does not have a RXERR line (RMII only).
363	  (so program the FEC to ignore it).
364
365config ETHER_ON_FEC2
366	bool "FEC2"
367	depends on MPC8XX_FEC && MPC885
368	default y
369
370config FEC2_PHY
371	int "FEC2 PHY"
372	depends on ETHER_ON_FEC2
373	default -1
374	help
375	  Define to the hardcoded PHY address which corresponds
376	  to the given FEC; i. e.
377		#define CONFIG_FEC1_PHY 4
378	  means that the PHY with address 4 is connected to FEC1
379
380	  When set to -1, means to probe for first available.
381
382config FEC2_PHY_NORXERR
383	bool "PHY_NORXERR"
384	depends on ETHER_ON_FEC2
385	default n
386	help
387	  The PHY does not have a RXERR line (RMII only).
388	  (so program the FEC to ignore it).
389
390config SYS_DPAA_QBMAN
391	bool "Device tree fixup for QBMan on freescale SOCs"
392	depends on (ARM || PPC) && !SPL_BUILD
393	default y if ARCH_B4860 || \
394		     ARCH_B4420 || \
395		     ARCH_P1023 || \
396		     ARCH_P2041 || \
397		     ARCH_T1023 || \
398		     ARCH_T1024 || \
399		     ARCH_T1040 || \
400		     ARCH_T1042 || \
401		     ARCH_T2080 || \
402		     ARCH_T2081 || \
403		     ARCH_T4240 || \
404		     ARCH_T4160 || \
405		     ARCH_P4080 || \
406		     ARCH_P3041 || \
407		     ARCH_P5040 || \
408		     ARCH_P5020 || \
409		     ARCH_LS1043A || \
410		     ARCH_LS1046A
411	help
412	  QBman fixups to allow deep sleep in DPAA 1 SOCs
413
414config TSEC_ENET
415	select PHYLIB
416	bool "Enable Three-Speed Ethernet Controller"
417	help
418	  This driver implements support for the (Enhanced) Three-Speed
419	  Ethernet Controller found on Freescale SoCs.
420
421endif # NETDEVICES
422