xref: /openbmc/u-boot/drivers/net/Kconfig (revision 59e43c32)
1source "drivers/net/phy/Kconfig"
2source "drivers/net/pfe_eth/Kconfig"
3
4config DM_ETH
5	bool "Enable Driver Model for Ethernet drivers"
6	depends on DM
7	help
8	  Enable driver model for Ethernet.
9
10	  The eth_*() interface will be implemented by the UCLASS_ETH class
11	  This is currently implemented in net/eth-uclass.c
12	  Look in include/net.h for details.
13
14config DRIVER_TI_CPSW
15	bool "TI Common Platform Ethernet Switch"
16	select PHYLIB
17	help
18	  This driver supports the TI three port switch gigabit ethernet
19	  subsystem found in the TI SoCs.
20
21menuconfig NETDEVICES
22	bool "Network device support"
23	depends on NET
24	default y if DM_ETH
25	help
26	  You must select Y to enable any network device support
27	  Generally if you have any networking support this is a given
28
29	  If unsure, say Y
30
31if NETDEVICES
32
33config PHY_GIGE
34	bool "Enable GbE PHY status parsing and configuration"
35	help
36	  Enables support for parsing the status output and for
37	  configuring GbE PHYs (affects the inner workings of some
38	  commands and miiphyutil.c).
39
40config AG7XXX
41	bool "Atheros AG7xxx Ethernet MAC support"
42	depends on DM_ETH && ARCH_ATH79
43	select PHYLIB
44	help
45	  This driver supports the Atheros AG7xxx Ethernet MAC. This MAC is
46	  present in the Atheros AR7xxx, AR9xxx and QCA9xxx MIPS chips.
47
48
49config ALTERA_TSE
50	bool "Altera Triple-Speed Ethernet MAC support"
51	depends on DM_ETH
52	select PHYLIB
53	help
54	  This driver supports the Altera Triple-Speed (TSE) Ethernet MAC.
55	  Please find details on the "Triple-Speed Ethernet MegaCore Function
56	  Resource Center" of Altera.
57
58config BCM_SF2_ETH
59	bool "Broadcom SF2 (Starfighter2) Ethernet support"
60	select PHYLIB
61	help
62	  This is an abstract framework which provides a generic interface
63	  to MAC and DMA management for multiple Broadcom SoCs such as
64	  Cygnus, NSP and bcm28155_ap platforms.
65
66config BCM_SF2_ETH_DEFAULT_PORT
67	int "Broadcom SF2 (Starfighter2) Ethernet default port number"
68	depends on BCM_SF2_ETH
69	default 0
70	help
71	  Default port number for the Starfighter2 ethernet driver.
72
73config BCM_SF2_ETH_GMAC
74	bool "Broadcom SF2 (Starfighter2) GMAC Ethernet support"
75	depends on BCM_SF2_ETH
76	help
77	  This flag enables the ethernet support for Broadcom platforms with
78	  GMAC such as Cygnus. This driver is based on the framework provided
79	  by the BCM_SF2_ETH driver.
80	  Say Y to any bcmcygnus based platforms.
81
82config DWC_ETH_QOS
83	bool "Synopsys DWC Ethernet QOS device support"
84	depends on DM_ETH
85	select PHYLIB
86	help
87	  This driver supports the Synopsys Designware Ethernet QOS (Quality
88	  Of Service) IP block. The IP supports many options for bus type,
89	  clocking/reset structure, and feature list. This driver currently
90	  supports the specific configuration used in NVIDIA's Tegra186 chip,
91	  but should be extensible to other combinations quite easily.
92
93config E1000
94	bool "Intel PRO/1000 Gigabit Ethernet support"
95	help
96	  This driver supports Intel(R) PRO/1000 gigabit ethernet family of
97	  adapters.  For more information on how to identify your adapter, go
98	  to the Adapter & Driver ID Guide at:
99
100	  <http://support.intel.com/support/network/adapter/pro100/21397.htm>
101
102config E1000_SPI_GENERIC
103	bool "Allow access to the Intel 8257x SPI bus"
104	depends on E1000
105	help
106	  Allow generic access to the SPI bus on the Intel 8257x, for
107	  example with the "sspi" command.
108
109config E1000_SPI
110	bool "Enable SPI bus utility code"
111	depends on E1000
112	help
113	  Utility code for direct access to the SPI bus on Intel 8257x.
114	  This does not do anything useful unless you set at least one
115	  of CONFIG_CMD_E1000 or CONFIG_E1000_SPI_GENERIC.
116
117config CMD_E1000
118	bool "Enable the e1000 command"
119	depends on E1000
120	help
121	  This enables the 'e1000' management command for E1000 devices. When
122	  used on devices with SPI support you can reprogram the EEPROM from
123	  U-Boot.
124
125config ETH_SANDBOX
126	depends on DM_ETH && SANDBOX
127	default y
128	bool "Sandbox: Mocked Ethernet driver"
129	help
130	  This driver simply responds with fake ARP replies and ping
131	  replies that are used to verify network stack functionality
132
133	  This driver is particularly useful in the test/dm/eth.c tests
134
135config ETH_SANDBOX_RAW
136	depends on DM_ETH && SANDBOX
137	default y
138	bool "Sandbox: Bridge to Linux Raw Sockets"
139	help
140	  This driver is a bridge from the bottom of the network stack
141	  in U-Boot to the RAW AF_PACKET API in Linux. This allows real
142	  network traffic to be tested from within sandbox. See
143	  board/sandbox/README.sandbox for more details.
144
145config ETH_DESIGNWARE
146	bool "Synopsys Designware Ethernet MAC"
147	select PHYLIB
148	help
149	  This MAC is present in SoCs from various vendors. It supports
150	  100Mbit and 1 Gbit operation. You must enable CONFIG_PHYLIB to
151	  provide the PHY (physical media interface).
152
153config ETH_DESIGNWARE_SOCFPGA
154	bool "Altera SoCFPGA extras for Synopsys Designware Ethernet MAC"
155	depends on DM_ETH && ETH_DESIGNWARE
156	help
157	  The Altera SoCFPGA requires additional configuration of the
158	  Altera system manager to correctly interface with the PHY.
159	  This code handles those SoC specifics.
160
161config ETHOC
162	bool "OpenCores 10/100 Mbps Ethernet MAC"
163	help
164	  This MAC is present in OpenRISC and Xtensa XTFPGA boards.
165
166config FEC_MXC_SHARE_MDIO
167	bool "Share the MDIO bus for FEC controller"
168	depends on FEC_MXC
169
170config FEC_MXC_MDIO_BASE
171	hex "MDIO base address for the FEC controller"
172	depends on FEC_MXC_SHARE_MDIO
173	help
174	  This specifies the MDIO registers base address. It is used when
175	  two FEC controllers share MDIO bus.
176
177config FEC_MXC
178	bool "FEC Ethernet controller"
179	depends on MX5 || MX6 || MX7
180	help
181	  This driver supports the 10/100 Fast Ethernet controller for
182	  NXP i.MX processors.
183
184config FTMAC100
185	bool "Ftmac100 Ethernet Support"
186	help
187	  This MAC is present in Andestech SoCs.
188
189config MVGBE
190	bool "Marvell Orion5x/Kirkwood network interface support"
191	depends on KIRKWOOD || ORION5X
192	select PHYLIB if DM_ETH
193	help
194	  This driver supports the network interface units in the
195	  Marvell Orion5x and Kirkwood SoCs
196
197config MVNETA
198	bool "Marvell Armada XP/385/3700 network interface support"
199	depends on ARMADA_XP || ARMADA_38X || ARMADA_3700
200	select PHYLIB
201	help
202	  This driver supports the network interface units in the
203	  Marvell ARMADA XP, ARMADA 38X and ARMADA 3700 SoCs
204
205config MVPP2
206	bool "Marvell Armada 375/7K/8K network interface support"
207	depends on ARMADA_375 || ARMADA_8K
208	select PHYLIB
209	help
210	  This driver supports the network interface units in the
211	  Marvell ARMADA 375, 7K and 8K SoCs.
212
213config MACB
214	bool "Cadence MACB/GEM Ethernet Interface"
215	depends on DM_ETH
216	select PHYLIB
217	help
218	  The Cadence MACB ethernet interface is found on many Atmel
219	  AT91 and SAMA5 parts.  This driver also supports the Cadence
220	  GEM (Gigabit Ethernet MAC) found in some ARM SoC devices.
221	  Say Y to include support for the MACB/GEM chip.
222
223config MACB_ZYNQ
224	bool "Cadence MACB/GEM Ethernet Interface for Xilinx Zynq"
225	depends on MACB
226	help
227	  The Cadence MACB ethernet interface was used on Zynq platform.
228	  Say Y to enable support for the MACB/GEM in Zynq chip.
229
230config PCH_GBE
231	bool "Intel Platform Controller Hub EG20T GMAC driver"
232	depends on DM_ETH && DM_PCI
233	select PHYLIB
234	help
235	  This MAC is present in Intel Platform Controller Hub EG20T. It
236	  supports 10/100/1000 Mbps operation.
237
238config RGMII
239	bool "Enable RGMII"
240	help
241	  Enable the support of the Reduced Gigabit Media-Independent
242	  Interface (RGMII).
243
244config MII
245	bool "Enable MII"
246	help
247	  Enable support of the Media-Independent Interface (MII)
248
249config RTL8139
250	bool "Realtek 8139 series Ethernet controller driver"
251	help
252	  This driver supports Realtek 8139 series fast ethernet family of
253	  PCI chipsets/adapters.
254
255config RTL8169
256	bool "Realtek 8169 series Ethernet controller driver"
257	help
258	  This driver supports Realtek 8169 series gigabit ethernet family of
259	  PCI/PCIe chipsets/adapters.
260
261config SMC911X
262	bool "SMSC LAN911x and LAN921x controller driver"
263
264if SMC911X
265
266config SMC911X_BASE
267	hex "SMC911X Base Address"
268	help
269	  Define this to hold the physical address
270	  of the device (I/O space)
271
272choice
273	prompt "SMC911X bus width"
274	default SMC911X_16_BIT
275
276config SMC911X_32_BIT
277	bool "Enable 32-bit interface"
278
279config SMC911X_16_BIT
280	bool "Enable 16-bit interface"
281	help
282	  Define this if data bus is 16 bits. If your processor
283	  automatically converts one 32 bit word to two 16 bit
284	  words you may also try CONFIG_SMC911X_32_BIT.
285
286endchoice
287endif #SMC911X
288
289config SUN7I_GMAC
290	bool "Enable Allwinner GMAC Ethernet support"
291	help
292	  Enable the support for Sun7i GMAC Ethernet controller
293
294config SUN7I_GMAC_FORCE_TXERR
295	bool "Force PA17 as gmac function"
296	depends on SUN7I_GMAC
297	help
298	  Some ethernet phys needs TXERR control. Since the GMAC
299	  doesn't have such signal, setting PA17 as GMAC function
300	  makes the pin output low, which enables data transmission.
301
302config SUN4I_EMAC
303	bool "Allwinner Sun4i Ethernet MAC support"
304	depends on DM_ETH
305	select PHYLIB
306	help
307	  This driver supports the Allwinner based SUN4I Ethernet MAC.
308
309config SUN8I_EMAC
310        bool "Allwinner Sun8i Ethernet MAC support"
311        depends on DM_ETH
312        select PHYLIB
313	select PHY_GIGE
314        help
315          This driver supports the  Allwinner based SUN8I/SUN50I Ethernet MAC.
316	  It can be found in H3/A64/A83T based SoCs and compatible with both
317	  External and Internal PHYs.
318
319config SH_ETHER
320	bool "Renesas SH Ethernet MAC"
321	select PHYLIB
322	help
323	  This driver supports the Ethernet for Renesas SH and ARM SoCs.
324
325config DRIVER_TI_EMAC
326	bool "TI Davinci EMAC"
327	help
328	   Support for davinci emac
329
330config XILINX_AXIEMAC
331	depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP)
332	select PHYLIB
333	select MII
334	bool "Xilinx AXI Ethernet"
335	help
336	  This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs.
337
338config XILINX_EMACLITE
339	depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP || MIPS)
340	select PHYLIB
341	select MII
342	bool "Xilinx Ethernetlite"
343	help
344	  This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs.
345
346config ZYNQ_GEM
347	depends on DM_ETH && (ARCH_ZYNQ || ARCH_ZYNQMP)
348	select PHYLIB
349	bool "Xilinx Ethernet GEM"
350	help
351	  This MAC is present in Xilinx Zynq and ZynqMP SoCs.
352
353config PIC32_ETH
354	bool "Microchip PIC32 Ethernet Support"
355	depends on DM_ETH && MACH_PIC32
356	select PHYLIB
357	help
358	  This driver implements 10/100 Mbps Ethernet and MAC layer for
359	  Microchip PIC32 microcontrollers.
360
361config GMAC_ROCKCHIP
362	bool "Rockchip Synopsys Designware Ethernet MAC"
363	depends on DM_ETH && ETH_DESIGNWARE
364	help
365	  This driver provides Rockchip SoCs network support based on the
366	  Synopsys Designware driver.
367
368config RENESAS_RAVB
369	bool "Renesas Ethernet AVB MAC"
370	depends on DM_ETH && RCAR_GEN3
371	select PHYLIB
372	help
373	  This driver implements support for the Ethernet AVB block in
374	  Renesas M3 and H3 SoCs.
375
376config MPC8XX_FEC
377	bool "Fast Ethernet Controller on MPC8XX"
378	depends on MPC8xx
379	select MII
380	help
381	  This driver implements support for the Fast Ethernet Controller
382	  on MPC8XX
383
384config SNI_AVE
385	bool "Socionext AVE Ethernet support"
386	depends on DM_ETH && ARCH_UNIPHIER
387	select PHYLIB
388	select SYSCON
389	select REGMAP
390	help
391	  This driver implements support for the Socionext AVE Ethernet
392	  controller, as found on the Socionext UniPhier family.
393
394config ETHER_ON_FEC1
395	bool "FEC1"
396	depends on MPC8XX_FEC
397	default y
398
399config FEC1_PHY
400	int "FEC1 PHY"
401	depends on ETHER_ON_FEC1
402	default -1
403	help
404	  Define to the hardcoded PHY address which corresponds
405	  to the given FEC; i. e.
406		#define CONFIG_FEC1_PHY 4
407	  means that the PHY with address 4 is connected to FEC1
408
409	  When set to -1, means to probe for first available.
410
411config PHY_NORXERR
412	bool "PHY_NORXERR"
413	depends on ETHER_ON_FEC1
414	default n
415	help
416	  The PHY does not have a RXERR line (RMII only).
417	  (so program the FEC to ignore it).
418
419config ETHER_ON_FEC2
420	bool "FEC2"
421	depends on MPC8XX_FEC && MPC885
422	default y
423
424config FEC2_PHY
425	int "FEC2 PHY"
426	depends on ETHER_ON_FEC2
427	default -1
428	help
429	  Define to the hardcoded PHY address which corresponds
430	  to the given FEC; i. e.
431		#define CONFIG_FEC1_PHY 4
432	  means that the PHY with address 4 is connected to FEC1
433
434	  When set to -1, means to probe for first available.
435
436config FEC2_PHY_NORXERR
437	bool "PHY_NORXERR"
438	depends on ETHER_ON_FEC2
439	default n
440	help
441	  The PHY does not have a RXERR line (RMII only).
442	  (so program the FEC to ignore it).
443
444config SYS_DPAA_QBMAN
445	bool "Device tree fixup for QBMan on freescale SOCs"
446	depends on (ARM || PPC) && !SPL_BUILD
447	default y if ARCH_B4860 || \
448		     ARCH_B4420 || \
449		     ARCH_P1023 || \
450		     ARCH_P2041 || \
451		     ARCH_T1023 || \
452		     ARCH_T1024 || \
453		     ARCH_T1040 || \
454		     ARCH_T1042 || \
455		     ARCH_T2080 || \
456		     ARCH_T2081 || \
457		     ARCH_T4240 || \
458		     ARCH_T4160 || \
459		     ARCH_P4080 || \
460		     ARCH_P3041 || \
461		     ARCH_P5040 || \
462		     ARCH_P5020 || \
463		     ARCH_LS1043A || \
464		     ARCH_LS1046A
465	help
466	  QBman fixups to allow deep sleep in DPAA 1 SOCs
467
468config TSEC_ENET
469	select PHYLIB
470	bool "Enable Three-Speed Ethernet Controller"
471	help
472	  This driver implements support for the (Enhanced) Three-Speed
473	  Ethernet Controller found on Freescale SoCs.
474
475endif # NETDEVICES
476