1source "drivers/net/phy/Kconfig" 2source "drivers/net/pfe_eth/Kconfig" 3 4config DM_ETH 5 bool "Enable Driver Model for Ethernet drivers" 6 depends on DM 7 help 8 Enable driver model for Ethernet. 9 10 The eth_*() interface will be implemented by the UCLASS_ETH class 11 This is currently implemented in net/eth-uclass.c 12 Look in include/net.h for details. 13 14config DRIVER_TI_CPSW 15 bool "TI Common Platform Ethernet Switch" 16 select PHYLIB 17 help 18 This driver supports the TI three port switch gigabit ethernet 19 subsystem found in the TI SoCs. 20 21menuconfig NETDEVICES 22 bool "Network device support" 23 depends on NET 24 default y if DM_ETH 25 help 26 You must select Y to enable any network device support 27 Generally if you have any networking support this is a given 28 29 If unsure, say Y 30 31if NETDEVICES 32 33config PHY_GIGE 34 bool "Enable GbE PHY status parsing and configuration" 35 help 36 Enables support for parsing the status output and for 37 configuring GbE PHYs (affects the inner workings of some 38 commands and miiphyutil.c). 39 40config AG7XXX 41 bool "Atheros AG7xxx Ethernet MAC support" 42 depends on DM_ETH && ARCH_ATH79 43 select PHYLIB 44 help 45 This driver supports the Atheros AG7xxx Ethernet MAC. This MAC is 46 present in the Atheros AR7xxx, AR9xxx and QCA9xxx MIPS chips. 47 48 49config ALTERA_TSE 50 bool "Altera Triple-Speed Ethernet MAC support" 51 depends on DM_ETH 52 select PHYLIB 53 help 54 This driver supports the Altera Triple-Speed (TSE) Ethernet MAC. 55 Please find details on the "Triple-Speed Ethernet MegaCore Function 56 Resource Center" of Altera. 57 58config BCM_SF2_ETH 59 bool "Broadcom SF2 (Starfighter2) Ethernet support" 60 select PHYLIB 61 help 62 This is an abstract framework which provides a generic interface 63 to MAC and DMA management for multiple Broadcom SoCs such as 64 Cygnus, NSP and bcm28155_ap platforms. 65 66config BCM_SF2_ETH_DEFAULT_PORT 67 int "Broadcom SF2 (Starfighter2) Ethernet default port number" 68 depends on BCM_SF2_ETH 69 default 0 70 help 71 Default port number for the Starfighter2 ethernet driver. 72 73config BCM_SF2_ETH_GMAC 74 bool "Broadcom SF2 (Starfighter2) GMAC Ethernet support" 75 depends on BCM_SF2_ETH 76 help 77 This flag enables the ethernet support for Broadcom platforms with 78 GMAC such as Cygnus. This driver is based on the framework provided 79 by the BCM_SF2_ETH driver. 80 Say Y to any bcmcygnus based platforms. 81 82config DWC_ETH_QOS 83 bool "Synopsys DWC Ethernet QOS device support" 84 depends on DM_ETH 85 select PHYLIB 86 help 87 This driver supports the Synopsys Designware Ethernet QOS (Quality 88 Of Service) IP block. The IP supports many options for bus type, 89 clocking/reset structure, and feature list. This driver currently 90 supports the specific configuration used in NVIDIA's Tegra186 chip, 91 but should be extensible to other combinations quite easily. 92 93config E1000 94 bool "Intel PRO/1000 Gigabit Ethernet support" 95 help 96 This driver supports Intel(R) PRO/1000 gigabit ethernet family of 97 adapters. For more information on how to identify your adapter, go 98 to the Adapter & Driver ID Guide at: 99 100 <http://support.intel.com/support/network/adapter/pro100/21397.htm> 101 102config E1000_SPI_GENERIC 103 bool "Allow access to the Intel 8257x SPI bus" 104 depends on E1000 105 help 106 Allow generic access to the SPI bus on the Intel 8257x, for 107 example with the "sspi" command. 108 109config E1000_SPI 110 bool "Enable SPI bus utility code" 111 depends on E1000 112 help 113 Utility code for direct access to the SPI bus on Intel 8257x. 114 This does not do anything useful unless you set at least one 115 of CONFIG_CMD_E1000 or CONFIG_E1000_SPI_GENERIC. 116 117config CMD_E1000 118 bool "Enable the e1000 command" 119 depends on E1000 120 help 121 This enables the 'e1000' management command for E1000 devices. When 122 used on devices with SPI support you can reprogram the EEPROM from 123 U-Boot. 124 125config ETH_SANDBOX 126 depends on DM_ETH && SANDBOX 127 default y 128 bool "Sandbox: Mocked Ethernet driver" 129 help 130 This driver simply responds with fake ARP replies and ping 131 replies that are used to verify network stack functionality 132 133 This driver is particularly useful in the test/dm/eth.c tests 134 135config ETH_SANDBOX_RAW 136 depends on DM_ETH && SANDBOX 137 default y 138 bool "Sandbox: Bridge to Linux Raw Sockets" 139 help 140 This driver is a bridge from the bottom of the network stack 141 in U-Boot to the RAW AF_PACKET API in Linux. This allows real 142 network traffic to be tested from within sandbox. See 143 board/sandbox/README.sandbox for more details. 144 145config ETH_DESIGNWARE 146 bool "Synopsys Designware Ethernet MAC" 147 select PHYLIB 148 help 149 This MAC is present in SoCs from various vendors. It supports 150 100Mbit and 1 Gbit operation. You must enable CONFIG_PHYLIB to 151 provide the PHY (physical media interface). 152 153config ETH_DESIGNWARE_SOCFPGA 154 bool "Altera SoCFPGA extras for Synopsys Designware Ethernet MAC" 155 depends on DM_ETH && ETH_DESIGNWARE 156 help 157 The Altera SoCFPGA requires additional configuration of the 158 Altera system manager to correctly interface with the PHY. 159 This code handles those SoC specifics. 160 161config ETHOC 162 bool "OpenCores 10/100 Mbps Ethernet MAC" 163 help 164 This MAC is present in OpenRISC and Xtensa XTFPGA boards. 165 166config FEC_MXC_SHARE_MDIO 167 bool "Share the MDIO bus for FEC controller" 168 depends on FEC_MXC 169 170config FEC_MXC_MDIO_BASE 171 hex "MDIO base address for the FEC controller" 172 depends on FEC_MXC_SHARE_MDIO 173 help 174 This specifies the MDIO registers base address. It is used when 175 two FEC controllers share MDIO bus. 176 177config FEC_MXC 178 bool "FEC Ethernet controller" 179 depends on MX5 || MX6 || MX7 180 help 181 This driver supports the 10/100 Fast Ethernet controller for 182 NXP i.MX processors. 183 184config FTMAC100 185 bool "Ftmac100 Ethernet Support" 186 help 187 This MAC is present in Andestech SoCs. 188 189config MVGBE 190 bool "Marvell Orion5x/Kirkwood network interface support" 191 depends on KIRKWOOD || ORION5X 192 select PHYLIB if DM_ETH 193 help 194 This driver supports the network interface units in the 195 Marvell Orion5x and Kirkwood SoCs 196 197config MVNETA 198 bool "Marvell Armada XP/385/3700 network interface support" 199 depends on ARMADA_XP || ARMADA_38X || ARMADA_3700 200 select PHYLIB 201 help 202 This driver supports the network interface units in the 203 Marvell ARMADA XP, ARMADA 38X and ARMADA 3700 SoCs 204 205config MVPP2 206 bool "Marvell Armada 375/7K/8K network interface support" 207 depends on ARMADA_375 || ARMADA_8K 208 select PHYLIB 209 help 210 This driver supports the network interface units in the 211 Marvell ARMADA 375, 7K and 8K SoCs. 212 213config MACB 214 bool "Cadence MACB/GEM Ethernet Interface" 215 depends on DM_ETH 216 select PHYLIB 217 help 218 The Cadence MACB ethernet interface is found on many Atmel 219 AT91 and SAMA5 parts. This driver also supports the Cadence 220 GEM (Gigabit Ethernet MAC) found in some ARM SoC devices. 221 Say Y to include support for the MACB/GEM chip. 222 223config MACB_ZYNQ 224 bool "Cadence MACB/GEM Ethernet Interface for Xilinx Zynq" 225 depends on MACB 226 help 227 The Cadence MACB ethernet interface was used on Zynq platform. 228 Say Y to enable support for the MACB/GEM in Zynq chip. 229 230config PCH_GBE 231 bool "Intel Platform Controller Hub EG20T GMAC driver" 232 depends on DM_ETH && DM_PCI 233 select PHYLIB 234 help 235 This MAC is present in Intel Platform Controller Hub EG20T. It 236 supports 10/100/1000 Mbps operation. 237 238config RGMII 239 bool "Enable RGMII" 240 help 241 Enable the support of the Reduced Gigabit Media-Independent 242 Interface (RGMII). 243 244config RTL8139 245 bool "Realtek 8139 series Ethernet controller driver" 246 help 247 This driver supports Realtek 8139 series fast ethernet family of 248 PCI chipsets/adapters. 249 250config RTL8169 251 bool "Realtek 8169 series Ethernet controller driver" 252 help 253 This driver supports Realtek 8169 series gigabit ethernet family of 254 PCI/PCIe chipsets/adapters. 255 256config SMC911X 257 bool "SMSC LAN911x and LAN921x controller driver" 258 259if SMC911X 260 261config SMC911X_BASE 262 hex "SMC911X Base Address" 263 help 264 Define this to hold the physical address 265 of the device (I/O space) 266 267choice 268 prompt "SMC911X bus width" 269 default SMC911X_16_BIT 270 271config SMC911X_32_BIT 272 bool "Enable 32-bit interface" 273 274config SMC911X_16_BIT 275 bool "Enable 16-bit interface" 276 help 277 Define this if data bus is 16 bits. If your processor 278 automatically converts one 32 bit word to two 16 bit 279 words you may also try CONFIG_SMC911X_32_BIT. 280 281endchoice 282endif #SMC911X 283 284config SUN7I_GMAC 285 bool "Enable Allwinner GMAC Ethernet support" 286 help 287 Enable the support for Sun7i GMAC Ethernet controller 288 289config SUN7I_GMAC_FORCE_TXERR 290 bool "Force PA17 as gmac function" 291 depends on SUN7I_GMAC 292 help 293 Some ethernet phys needs TXERR control. Since the GMAC 294 doesn't have such signal, setting PA17 as GMAC function 295 makes the pin output low, which enables data transmission. 296 297config SUN4I_EMAC 298 bool "Allwinner Sun4i Ethernet MAC support" 299 depends on DM_ETH 300 select PHYLIB 301 help 302 This driver supports the Allwinner based SUN4I Ethernet MAC. 303 304config SUN8I_EMAC 305 bool "Allwinner Sun8i Ethernet MAC support" 306 depends on DM_ETH 307 select PHYLIB 308 select PHY_GIGE 309 help 310 This driver supports the Allwinner based SUN8I/SUN50I Ethernet MAC. 311 It can be found in H3/A64/A83T based SoCs and compatible with both 312 External and Internal PHYs. 313 314config SH_ETHER 315 bool "Renesas SH Ethernet MAC" 316 select PHYLIB 317 help 318 This driver supports the Ethernet for Renesas SH and ARM SoCs. 319 320config XILINX_AXIEMAC 321 depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP) 322 select PHYLIB 323 select MII 324 bool "Xilinx AXI Ethernet" 325 help 326 This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs. 327 328config XILINX_EMACLITE 329 depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP || MIPS) 330 select PHYLIB 331 select MII 332 bool "Xilinx Ethernetlite" 333 help 334 This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs. 335 336config ZYNQ_GEM 337 depends on DM_ETH && (ARCH_ZYNQ || ARCH_ZYNQMP) 338 select PHYLIB 339 bool "Xilinx Ethernet GEM" 340 help 341 This MAC is present in Xilinx Zynq and ZynqMP SoCs. 342 343config PIC32_ETH 344 bool "Microchip PIC32 Ethernet Support" 345 depends on DM_ETH && MACH_PIC32 346 select PHYLIB 347 help 348 This driver implements 10/100 Mbps Ethernet and MAC layer for 349 Microchip PIC32 microcontrollers. 350 351config GMAC_ROCKCHIP 352 bool "Rockchip Synopsys Designware Ethernet MAC" 353 depends on DM_ETH && ETH_DESIGNWARE 354 help 355 This driver provides Rockchip SoCs network support based on the 356 Synopsys Designware driver. 357 358config RENESAS_RAVB 359 bool "Renesas Ethernet AVB MAC" 360 depends on DM_ETH && RCAR_GEN3 361 select PHYLIB 362 help 363 This driver implements support for the Ethernet AVB block in 364 Renesas M3 and H3 SoCs. 365 366config MPC8XX_FEC 367 bool "Fast Ethernet Controller on MPC8XX" 368 depends on MPC8xx 369 select MII 370 help 371 This driver implements support for the Fast Ethernet Controller 372 on MPC8XX 373 374config SNI_AVE 375 bool "Socionext AVE Ethernet support" 376 depends on DM_ETH && ARCH_UNIPHIER 377 select PHYLIB 378 select SYSCON 379 select REGMAP 380 help 381 This driver implements support for the Socionext AVE Ethernet 382 controller, as found on the Socionext UniPhier family. 383 384config ETHER_ON_FEC1 385 bool "FEC1" 386 depends on MPC8XX_FEC 387 default y 388 389config FEC1_PHY 390 int "FEC1 PHY" 391 depends on ETHER_ON_FEC1 392 default -1 393 help 394 Define to the hardcoded PHY address which corresponds 395 to the given FEC; i. e. 396 #define CONFIG_FEC1_PHY 4 397 means that the PHY with address 4 is connected to FEC1 398 399 When set to -1, means to probe for first available. 400 401config PHY_NORXERR 402 bool "PHY_NORXERR" 403 depends on ETHER_ON_FEC1 404 default n 405 help 406 The PHY does not have a RXERR line (RMII only). 407 (so program the FEC to ignore it). 408 409config ETHER_ON_FEC2 410 bool "FEC2" 411 depends on MPC8XX_FEC && MPC885 412 default y 413 414config FEC2_PHY 415 int "FEC2 PHY" 416 depends on ETHER_ON_FEC2 417 default -1 418 help 419 Define to the hardcoded PHY address which corresponds 420 to the given FEC; i. e. 421 #define CONFIG_FEC1_PHY 4 422 means that the PHY with address 4 is connected to FEC1 423 424 When set to -1, means to probe for first available. 425 426config FEC2_PHY_NORXERR 427 bool "PHY_NORXERR" 428 depends on ETHER_ON_FEC2 429 default n 430 help 431 The PHY does not have a RXERR line (RMII only). 432 (so program the FEC to ignore it). 433 434config SYS_DPAA_QBMAN 435 bool "Device tree fixup for QBMan on freescale SOCs" 436 depends on (ARM || PPC) && !SPL_BUILD 437 default y if ARCH_B4860 || \ 438 ARCH_B4420 || \ 439 ARCH_P1023 || \ 440 ARCH_P2041 || \ 441 ARCH_T1023 || \ 442 ARCH_T1024 || \ 443 ARCH_T1040 || \ 444 ARCH_T1042 || \ 445 ARCH_T2080 || \ 446 ARCH_T2081 || \ 447 ARCH_T4240 || \ 448 ARCH_T4160 || \ 449 ARCH_P4080 || \ 450 ARCH_P3041 || \ 451 ARCH_P5040 || \ 452 ARCH_P5020 || \ 453 ARCH_LS1043A || \ 454 ARCH_LS1046A 455 help 456 QBman fixups to allow deep sleep in DPAA 1 SOCs 457 458config TSEC_ENET 459 select PHYLIB 460 bool "Enable Three-Speed Ethernet Controller" 461 help 462 This driver implements support for the (Enhanced) Three-Speed 463 Ethernet Controller found on Freescale SoCs. 464 465endif # NETDEVICES 466