1source "drivers/net/phy/Kconfig" 2source "drivers/net/pfe_eth/Kconfig" 3 4config DM_ETH 5 bool "Enable Driver Model for Ethernet drivers" 6 depends on DM 7 help 8 Enable driver model for Ethernet. 9 10 The eth_*() interface will be implemented by the UC_ETH class 11 This is currently implemented in net/eth.c 12 Look in include/net.h for details. 13 14config DRIVER_TI_CPSW 15 bool "TI Common Platform Ethernet Switch" 16 select PHYLIB 17 help 18 This driver supports the TI three port switch gigabit ethernet 19 subsystem found in the TI SoCs. 20 21menuconfig NETDEVICES 22 bool "Network device support" 23 depends on NET 24 default y if DM_ETH 25 help 26 You must select Y to enable any network device support 27 Generally if you have any networking support this is a given 28 29 If unsure, say Y 30 31if NETDEVICES 32 33config PHY_GIGE 34 bool "Enable GbE PHY status parsing and configuration" 35 help 36 Enables support for parsing the status output and for 37 configuring GbE PHYs (affects the inner workings of some 38 commands and miiphyutil.c). 39 40config AG7XXX 41 bool "Atheros AG7xxx Ethernet MAC support" 42 depends on DM_ETH && ARCH_ATH79 43 select PHYLIB 44 help 45 This driver supports the Atheros AG7xxx Ethernet MAC. This MAC is 46 present in the Atheros AR7xxx, AR9xxx and QCA9xxx MIPS chips. 47 48 49config ALTERA_TSE 50 bool "Altera Triple-Speed Ethernet MAC support" 51 depends on DM_ETH 52 select PHYLIB 53 help 54 This driver supports the Altera Triple-Speed (TSE) Ethernet MAC. 55 Please find details on the "Triple-Speed Ethernet MegaCore Function 56 Resource Center" of Altera. 57 58config BCM_SF2_ETH 59 bool "Broadcom SF2 (Starfighter2) Ethernet support" 60 select PHYLIB 61 help 62 This is an abstract framework which provides a generic interface 63 to MAC and DMA management for multiple Broadcom SoCs such as 64 Cygnus, NSP and bcm28155_ap platforms. 65 66config BCM_SF2_ETH_DEFAULT_PORT 67 int "Broadcom SF2 (Starfighter2) Ethernet default port number" 68 depends on BCM_SF2_ETH 69 default 0 70 help 71 Default port number for the Starfighter2 ethernet driver. 72 73config BCM_SF2_ETH_GMAC 74 bool "Broadcom SF2 (Starfighter2) GMAC Ethernet support" 75 depends on BCM_SF2_ETH 76 help 77 This flag enables the ethernet support for Broadcom platforms with 78 GMAC such as Cygnus. This driver is based on the framework provided 79 by the BCM_SF2_ETH driver. 80 Say Y to any bcmcygnus based platforms. 81 82config DWC_ETH_QOS 83 bool "Synopsys DWC Ethernet QOS device support" 84 depends on DM_ETH 85 select PHYLIB 86 help 87 This driver supports the Synopsys Designware Ethernet QOS (Quality 88 Of Service) IP block. The IP supports many options for bus type, 89 clocking/reset structure, and feature list. This driver currently 90 supports the specific configuration used in NVIDIA's Tegra186 chip, 91 but should be extensible to other combinations quite easily. 92 93config E1000 94 bool "Intel PRO/1000 Gigabit Ethernet support" 95 help 96 This driver supports Intel(R) PRO/1000 gigabit ethernet family of 97 adapters. For more information on how to identify your adapter, go 98 to the Adapter & Driver ID Guide at: 99 100 <http://support.intel.com/support/network/adapter/pro100/21397.htm> 101 102config E1000_SPI_GENERIC 103 bool "Allow access to the Intel 8257x SPI bus" 104 depends on E1000 105 help 106 Allow generic access to the SPI bus on the Intel 8257x, for 107 example with the "sspi" command. 108 109config E1000_SPI 110 bool "Enable SPI bus utility code" 111 depends on E1000 112 help 113 Utility code for direct access to the SPI bus on Intel 8257x. 114 This does not do anything useful unless you set at least one 115 of CONFIG_CMD_E1000 or CONFIG_E1000_SPI_GENERIC. 116 117config CMD_E1000 118 bool "Enable the e1000 command" 119 depends on E1000 120 help 121 This enables the 'e1000' management command for E1000 devices. When 122 used on devices with SPI support you can reprogram the EEPROM from 123 U-Boot. 124 125config ETH_SANDBOX 126 depends on DM_ETH && SANDBOX 127 default y 128 bool "Sandbox: Mocked Ethernet driver" 129 help 130 This driver simply responds with fake ARP replies and ping 131 replies that are used to verify network stack functionality 132 133 This driver is particularly useful in the test/dm/eth.c tests 134 135config ETH_SANDBOX_RAW 136 depends on DM_ETH && SANDBOX 137 default y 138 bool "Sandbox: Bridge to Linux Raw Sockets" 139 help 140 This driver is a bridge from the bottom of the network stack 141 in U-Boot to the RAW AF_PACKET API in Linux. This allows real 142 network traffic to be tested from within sandbox. See 143 board/sandbox/README.sandbox for more details. 144 145config ETH_DESIGNWARE 146 bool "Synopsys Designware Ethernet MAC" 147 select PHYLIB 148 help 149 This MAC is present in SoCs from various vendors. It supports 150 100Mbit and 1 Gbit operation. You must enable CONFIG_PHYLIB to 151 provide the PHY (physical media interface). 152 153config ETHOC 154 bool "OpenCores 10/100 Mbps Ethernet MAC" 155 help 156 This MAC is present in OpenRISC and Xtensa XTFPGA boards. 157 158config FEC_MXC_SHARE_MDIO 159 bool "Share the MDIO bus for FEC controller" 160 depends on FEC_MXC 161 162config FEC_MXC_MDIO_BASE 163 hex "MDIO base address for the FEC controller" 164 depends on FEC_MXC_SHARE_MDIO 165 help 166 This specifies the MDIO registers base address. It is used when 167 two FEC controllers share MDIO bus. 168 169config FEC_MXC 170 bool "FEC Ethernet controller" 171 depends on MX5 || MX6 || MX7 172 help 173 This driver supports the 10/100 Fast Ethernet controller for 174 NXP i.MX processors. 175 176config FTMAC100 177 bool "Ftmac100 Ethernet Support" 178 help 179 This MAC is present in Andestech SoCs. 180 181config MVNETA 182 bool "Marvell Armada XP/385/3700 network interface support" 183 depends on ARMADA_XP || ARMADA_38X || ARMADA_3700 184 select PHYLIB 185 help 186 This driver supports the network interface units in the 187 Marvell ARMADA XP, ARMADA 38X and ARMADA 3700 SoCs 188 189config MVPP2 190 bool "Marvell Armada 375/7K/8K network interface support" 191 depends on ARMADA_375 || ARMADA_8K 192 select PHYLIB 193 help 194 This driver supports the network interface units in the 195 Marvell ARMADA 375, 7K and 8K SoCs. 196 197config MACB 198 bool "Cadence MACB/GEM Ethernet Interface" 199 depends on DM_ETH 200 select PHYLIB 201 help 202 The Cadence MACB ethernet interface is found on many Atmel 203 AT91 and SAMA5 parts. This driver also supports the Cadence 204 GEM (Gigabit Ethernet MAC) found in some ARM SoC devices. 205 Say Y to include support for the MACB/GEM chip. 206 207config MACB_ZYNQ 208 bool "Cadence MACB/GEM Ethernet Interface for Xilinx Zynq" 209 depends on MACB 210 help 211 The Cadence MACB ethernet interface was used on Zynq platform. 212 Say Y to enable support for the MACB/GEM in Zynq chip. 213 214config PCH_GBE 215 bool "Intel Platform Controller Hub EG20T GMAC driver" 216 depends on DM_ETH && DM_PCI 217 select PHYLIB 218 help 219 This MAC is present in Intel Platform Controller Hub EG20T. It 220 supports 10/100/1000 Mbps operation. 221 222config RGMII 223 bool "Enable RGMII" 224 help 225 Enable the support of the Reduced Gigabit Media-Independent 226 Interface (RGMII). 227 228config RTL8139 229 bool "Realtek 8139 series Ethernet controller driver" 230 help 231 This driver supports Realtek 8139 series fast ethernet family of 232 PCI chipsets/adapters. 233 234config RTL8169 235 bool "Realtek 8169 series Ethernet controller driver" 236 help 237 This driver supports Realtek 8169 series gigabit ethernet family of 238 PCI/PCIe chipsets/adapters. 239 240config SMC911X 241 bool "SMSC LAN911x and LAN921x controller driver" 242 243if SMC911X 244 245config SMC911X_BASE 246 hex "SMC911X Base Address" 247 help 248 Define this to hold the physical address 249 of the device (I/O space) 250 251choice 252 prompt "SMC911X bus width" 253 default SMC911X_16_BIT 254 255config SMC911X_32_BIT 256 bool "Enable 32-bit interface" 257 258config SMC911X_16_BIT 259 bool "Enable 16-bit interface" 260 help 261 Define this if data bus is 16 bits. If your processor 262 automatically converts one 32 bit word to two 16 bit 263 words you may also try CONFIG_SMC911X_32_BIT. 264 265endchoice 266endif #SMC911X 267 268config SUN7I_GMAC 269 bool "Enable Allwinner GMAC Ethernet support" 270 help 271 Enable the support for Sun7i GMAC Ethernet controller 272 273config SUN7I_GMAC_FORCE_TXERR 274 bool "Force PA17 as gmac function" 275 depends on SUN7I_GMAC 276 help 277 Some ethernet phys needs TXERR control. Since the GMAC 278 doesn't have such signal, setting PA17 as GMAC function 279 makes the pin output low, which enables data transmission. 280 281config SUN4I_EMAC 282 bool "Allwinner Sun4i Ethernet MAC support" 283 depends on DM_ETH 284 select PHYLIB 285 help 286 This driver supports the Allwinner based SUN4I Ethernet MAC. 287 288config SUN8I_EMAC 289 bool "Allwinner Sun8i Ethernet MAC support" 290 depends on DM_ETH 291 select PHYLIB 292 select PHY_GIGE 293 help 294 This driver supports the Allwinner based SUN8I/SUN50I Ethernet MAC. 295 It can be found in H3/A64/A83T based SoCs and compatible with both 296 External and Internal PHYs. 297 298config SH_ETHER 299 bool "Renesas SH Ethernet MAC" 300 select PHYLIB 301 help 302 This driver supports the Ethernet for Renesas SH and ARM SoCs. 303 304config XILINX_AXIEMAC 305 depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP) 306 select PHYLIB 307 select MII 308 bool "Xilinx AXI Ethernet" 309 help 310 This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs. 311 312config XILINX_EMACLITE 313 depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP || MIPS) 314 select PHYLIB 315 select MII 316 bool "Xilinx Ethernetlite" 317 help 318 This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs. 319 320config ZYNQ_GEM 321 depends on DM_ETH && (ARCH_ZYNQ || ARCH_ZYNQMP) 322 select PHYLIB 323 bool "Xilinx Ethernet GEM" 324 help 325 This MAC is present in Xilinx Zynq and ZynqMP SoCs. 326 327config PIC32_ETH 328 bool "Microchip PIC32 Ethernet Support" 329 depends on DM_ETH && MACH_PIC32 330 select PHYLIB 331 help 332 This driver implements 10/100 Mbps Ethernet and MAC layer for 333 Microchip PIC32 microcontrollers. 334 335config GMAC_ROCKCHIP 336 bool "Rockchip Synopsys Designware Ethernet MAC" 337 depends on DM_ETH && ETH_DESIGNWARE 338 help 339 This driver provides Rockchip SoCs network support based on the 340 Synopsys Designware driver. 341 342config RENESAS_RAVB 343 bool "Renesas Ethernet AVB MAC" 344 depends on DM_ETH && RCAR_GEN3 345 select PHYLIB 346 help 347 This driver implements support for the Ethernet AVB block in 348 Renesas M3 and H3 SoCs. 349 350config MPC8XX_FEC 351 bool "Fast Ethernet Controller on MPC8XX" 352 depends on MPC8xx 353 select MII 354 help 355 This driver implements support for the Fast Ethernet Controller 356 on MPC8XX 357 358config ETHER_ON_FEC1 359 bool "FEC1" 360 depends on MPC8XX_FEC 361 default y 362 363config FEC1_PHY 364 int "FEC1 PHY" 365 depends on ETHER_ON_FEC1 366 default -1 367 help 368 Define to the hardcoded PHY address which corresponds 369 to the given FEC; i. e. 370 #define CONFIG_FEC1_PHY 4 371 means that the PHY with address 4 is connected to FEC1 372 373 When set to -1, means to probe for first available. 374 375config PHY_NORXERR 376 bool "PHY_NORXERR" 377 depends on ETHER_ON_FEC1 378 default n 379 help 380 The PHY does not have a RXERR line (RMII only). 381 (so program the FEC to ignore it). 382 383config ETHER_ON_FEC2 384 bool "FEC2" 385 depends on MPC8XX_FEC && MPC885 386 default y 387 388config FEC2_PHY 389 int "FEC2 PHY" 390 depends on ETHER_ON_FEC2 391 default -1 392 help 393 Define to the hardcoded PHY address which corresponds 394 to the given FEC; i. e. 395 #define CONFIG_FEC1_PHY 4 396 means that the PHY with address 4 is connected to FEC1 397 398 When set to -1, means to probe for first available. 399 400config FEC2_PHY_NORXERR 401 bool "PHY_NORXERR" 402 depends on ETHER_ON_FEC2 403 default n 404 help 405 The PHY does not have a RXERR line (RMII only). 406 (so program the FEC to ignore it). 407 408config SYS_DPAA_QBMAN 409 bool "Device tree fixup for QBMan on freescale SOCs" 410 depends on (ARM || PPC) && !SPL_BUILD 411 default y if ARCH_B4860 || \ 412 ARCH_B4420 || \ 413 ARCH_P1023 || \ 414 ARCH_P2041 || \ 415 ARCH_T1023 || \ 416 ARCH_T1024 || \ 417 ARCH_T1040 || \ 418 ARCH_T1042 || \ 419 ARCH_T2080 || \ 420 ARCH_T2081 || \ 421 ARCH_T4240 || \ 422 ARCH_T4160 || \ 423 ARCH_P4080 || \ 424 ARCH_P3041 || \ 425 ARCH_P5040 || \ 426 ARCH_P5020 || \ 427 ARCH_LS1043A || \ 428 ARCH_LS1046A 429 help 430 QBman fixups to allow deep sleep in DPAA 1 SOCs 431 432config TSEC_ENET 433 select PHYLIB 434 bool "Enable Three-Speed Ethernet Controller" 435 help 436 This driver implements support for the (Enhanced) Three-Speed 437 Ethernet Controller found on Freescale SoCs. 438 439endif # NETDEVICES 440