1The chosen node
2---------------
3The chosen node does not represent a real device, but serves as a place
4for passing data like which serial device to used to print the logs etc
5
6
7stdout-path property
8--------------------
9Device trees may specify the device to be used for boot console output
10with a stdout-path property under /chosen.
11
12Example
13-------
14/ {
15	chosen {
16		stdout-path = "/serial@f00:115200";
17	};
18
19	serial@f00 {
20		compatible = "vendor,some-uart";
21		reg = <0xf00 0x10>;
22	};
23};
24
25tick-timer property
26-------------------
27In a system there are multiple timers, specify which timer to be used
28as the tick-timer. Earlier it was hardcoded in the timer driver now
29since device tree has all the timer nodes. Specify which timer to be
30used as tick timer.
31
32Example
33-------
34/ {
35	chosen {
36		tick-timer = "/timer2@f00";
37	};
38
39	timer2@f00 {
40		compatible = "vendor,some-timer";
41		reg = <0xf00 0x10>;
42	};
43};
44
45u-boot,bootcount-device property
46--------------------------------
47
48In a DM-based system, the bootcount may be stored in a device known to
49the DM framework (e.g. in a battery-backed SRAM area within a RTC
50device) managed by a device conforming to UCLASS_BOOTCOUNT.  If
51multiple such devices are present in a system concurrently, then the
52u-boot,bootcount-device property can select the preferred target.
53
54Example
55-------
56/ {
57	chosen {
58	        u-boot,bootcount-device = &bootcount-rv3029;
59	};
60
61	bootcount-rv3029: bootcount@0 {
62		compatible = "u-boot,bootcount-rtc";
63		rtc = &rv3029;
64		offset = <0x38>;
65	};
66
67	i2c2 {
68	        rv3029: rtc@56 {
69		                compatible = "mc,rv3029";
70		                reg = <0x56>;
71		};
72	};
73};
74
75u-boot,spl-boot-order property
76------------------------------
77
78In a system using an SPL stage and having multiple boot sources
79(e.g. SPI NOR flash, on-board eMMC and a removable SD-card), the boot
80device may be probed by reading the image and verifying an image
81signature.
82
83If the SPL is configured through the device-tree, the boot-order can
84be configured with the spl-boot-order property under the /chosen node.
85Each list element of the property should specify a device to be probed
86in the order they are listed: references (i.e. implicit paths), a full
87path or an alias is expected for each entry.
88
89A special specifier "same-as-spl" can be used at any position in the
90boot-order to direct U-Boot to insert the device the SPL was booted
91from there.  Whether this is indeed inserted or silently ignored (if
92it is not supported on any given SoC/board or if the boot-device is
93not available to continue booting from) is implementation-defined.
94Note that if "same-as-spl" expands to an actual node for a given
95board, the corresponding node may appear multiple times in the
96boot-order (as there currently exists no mechanism to suppress
97duplicates from the list).
98
99Example
100-------
101/ {
102	chosen {
103		u-boot,spl-boot-order = "same-as-spl", &sdmmc, "/sdhci@fe330000";
104	};
105};
106
107u-boot,spl-boot-device property
108-------------------------------
109
110This property is a companion-property to the u-boot,spl-boot-order and
111will be injected automatically by the SPL stage to notify a later stage
112of where said later stage was booted from.
113
114You should not define this property yourself in the device-tree, as it
115may be overwritten without warning.
116
117firmware-loader property
118------------------------
119Multiple file system firmware loader nodes could be defined in device trees for
120multiple storage type and their default partition, then a property
121"firmware-loader" can be used to pass default firmware loader
122node(default storage type) to the firmware loader driver.
123
124Example
125-------
126/ {
127	chosen {
128		firmware-loader = &fs_loader0;
129	};
130
131	fs_loader0: fs-loader@0 {
132		u-boot,dm-pre-reloc;
133		compatible = "u-boot,fs-loader";
134		phandlepart = <&mmc 1>;
135	};
136};
137