1# 2# (C) Copyright 2009 3# Marvell Semiconductor <www.marvell.com> 4# Written-by: Prafulla Wadaskar <prafulla@marvell.com> 5# 6# SPDX-License-Identifier: GPL-2.0+ 7# 8# Refer to doc/README.kwbimage for more details about how-to 9# configure and create kirkwood boot images. 10# 11 12# Boot Media configurations 13BOOT_FROM nand 14NAND_ECC_MODE default 15NAND_PAGE_SIZE 0x0800 16 17# SOC registers configuration using bootrom header extension 18# Maximum KWBIMAGE_MAX_CONFIG configurations allowed 19 20# Configure RGMII-0 interface pad voltage to 1.8V 21DATA 0xFFD100e0 0x1b1b1b9b 22 23#Dram initalization for SINGLE x16 CL=5 @ 400MHz 24DATA 0xFFD01400 0x43000c30 # DDR Configuration register 25# bit13-0: 0xc30 (3120 DDR2 clks refresh rate) 26# bit23-14: zero 27# bit24: 1= enable exit self refresh mode on DDR access 28# bit25: 1 required 29# bit29-26: zero 30# bit31-30: 01 31 32DATA 0xFFD01404 0x37543000 # DDR Controller Control Low 33# bit 4: 0=addr/cmd in smame cycle 34# bit 5: 0=clk is driven during self refresh, we don't care for APX 35# bit 6: 0=use recommended falling edge of clk for addr/cmd 36# bit14: 0=input buffer always powered up 37# bit18: 1=cpu lock transaction enabled 38# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0 39# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM 40# bit30-28: 3 required 41# bit31: 0=no additional STARTBURST delay 42 43DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value +1) 44# bit3-0: TRAS lsbs 45# bit7-4: TRCD 46# bit11- 8: TRP 47# bit15-12: TWR 48# bit19-16: TWTR 49# bit20: TRAS msb 50# bit23-21: 0x0 51# bit27-24: TRRD 52# bit31-28: TRTP 53 54DATA 0xFFD0140C 0x00000a33 # DDR Timing (High) 55# bit6-0: TRFC 56# bit8-7: TR2R 57# bit10-9: TR2W 58# bit12-11: TW2W 59# bit31-13: zero required 60 61DATA 0xFFD01410 0x000000cc # DDR Address Control 62# bit1-0: 00, Cs0width=x8 63# bit3-2: 11, Cs0size=1Gb 64# bit5-4: 00, Cs1width=x8 65# bit7-6: 11, Cs1size=1Gb 66# bit9-8: 00, Cs2width=nonexistent 67# bit11-10: 00, Cs2size =nonexistent 68# bit13-12: 00, Cs3width=nonexistent 69# bit15-14: 00, Cs3size =nonexistent 70# bit16: 0, Cs0AddrSel 71# bit17: 0, Cs1AddrSel 72# bit18: 0, Cs2AddrSel 73# bit19: 0, Cs3AddrSel 74# bit31-20: 0 required 75 76DATA 0xFFD01414 0x00000000 # DDR Open Pages Control 77# bit0: 0, OpenPage enabled 78# bit31-1: 0 required 79 80DATA 0xFFD01418 0x00000000 # DDR Operation 81# bit3-0: 0x0, DDR cmd 82# bit31-4: 0 required 83 84DATA 0xFFD0141C 0x00000C52 # DDR Mode 85# bit2-0: 2, BurstLen=2 required 86# bit3: 0, BurstType=0 required 87# bit6-4: 4, CL=5 88# bit7: 0, TestMode=0 normal 89# bit8: 0, DLL reset=0 normal 90# bit11-9: 6, auto-precharge write recovery ???????????? 91# bit12: 0, PD must be zero 92# bit31-13: 0 required 93 94DATA 0xFFD01420 0x00000040 # DDR Extended Mode 95# bit0: 0, DDR DLL enabled 96# bit1: 0, DDR drive strenght normal 97# bit2: 0, DDR ODT control lsd (disabled) 98# bit5-3: 000, required 99# bit6: 1, DDR ODT control msb, (disabled) 100# bit9-7: 000, required 101# bit10: 0, differential DQS enabled 102# bit11: 0, required 103# bit12: 0, DDR output buffer enabled 104# bit31-13: 0 required 105 106DATA 0xFFD01424 0x0000F17F # DDR Controller Control High 107# bit2-0: 111, required 108# bit3 : 1 , MBUS Burst Chop disabled 109# bit6-4: 111, required 110# bit7 : 0 111# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz 112# bit9 : 0 , no half clock cycle addition to dataout 113# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals 114# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh 115# bit15-12: 1111 required 116# bit31-16: 0 required 117 118DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values) 119DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values) 120 121DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0 122DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size 123# bit0: 1, Window enabled 124# bit1: 0, Write Protect disabled 125# bit3-2: 00, CS0 hit selected 126# bit23-4: ones, required 127# bit31-24: 0x0F, Size (i.e. 256MB) 128 129DATA 0xFFD01508 0x10000000 # CS[1]n Base address to 256Mb 130DATA 0xFFD0150C 0x0FFFFFF5 # CS[1]n Size 256Mb Window enabled for CS1 131 132DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled 133DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled 134 135DATA 0xFFD01494 0x00030000 # DDR ODT Control (Low) 136DATA 0xFFD01498 0x00000000 # DDR ODT Control (High) 137# bit1-0: 00, ODT0 controlled by ODT Control (low) register above 138# bit3-2: 01, ODT1 active NEVER! 139# bit31-4: zero, required 140 141DATA 0xFFD0149C 0x0000E803 # CPU ODT Control 142DATA 0xFFD01480 0x00000001 # DDR Initialization Control 143#bit0=1, enable DDR init upon this register write 144 145# End of Header extension 146DATA 0x0 0x0 147