1menu "x86 architecture" 2 depends on X86 3 4config SYS_ARCH 5 default "x86" 6 7choice 8 prompt "Run U-Boot in 32/64-bit mode" 9 default X86_RUN_32BIT 10 help 11 U-Boot can be built as a 32-bit binary which runs in 32-bit mode 12 even on 64-bit machines. In this case SPL is not used, and U-Boot 13 runs directly from the reset vector (via 16-bit start-up). 14 15 Alternatively it can be run as a 64-bit binary, thus requiring a 16 64-bit machine. In this case SPL runs in 32-bit mode (via 16-bit 17 start-up) then jumps to U-Boot in 64-bit mode. 18 19 For now, 32-bit mode is recommended, as 64-bit is still 20 experimental and is missing a lot of features. 21 22config X86_RUN_32BIT 23 bool "32-bit" 24 help 25 Build U-Boot as a 32-bit binary with no SPL. This is the currently 26 supported normal setup. U-Boot will stay in 32-bit mode even on 27 64-bit machines. When booting a 64-bit kernel, U-Boot will switch 28 to 64-bit just before starting the kernel. Only the bottom 4GB of 29 memory can be accessed through normal means, although 30 arch_phys_memset() can be used for basic access to other memory. 31 32config X86_RUN_64BIT 33 bool "64-bit" 34 select X86_64 35 select SUPPORT_SPL 36 select SPL 37 select SPL_SEPARATE_BSS 38 help 39 Build U-Boot as a 64-bit binary with a 32-bit SPL. This is 40 experimental and many features are missing. U-Boot SPL starts up, 41 runs through the 16-bit and 32-bit init, then switches to 64-bit 42 mode and jumps to U-Boot proper. 43 44endchoice 45 46config X86_64 47 bool 48 49config SPL_X86_64 50 bool 51 depends on SPL 52 53choice 54 prompt "Mainboard vendor" 55 default VENDOR_EMULATION 56 57config VENDOR_ADVANTECH 58 bool "advantech" 59 60config VENDOR_CONGATEC 61 bool "congatec" 62 63config VENDOR_COREBOOT 64 bool "coreboot" 65 66config VENDOR_DFI 67 bool "dfi" 68 69config VENDOR_EFI 70 bool "efi" 71 72config VENDOR_EMULATION 73 bool "emulation" 74 75config VENDOR_GOOGLE 76 bool "Google" 77 78config VENDOR_INTEL 79 bool "Intel" 80 81endchoice 82 83# subarchitectures-specific options below 84config INTEL_MID 85 bool "Intel MID platform support" 86 select REGMAP 87 select SYSCON 88 help 89 Select to build a U-Boot capable of supporting Intel MID 90 (Mobile Internet Device) platform systems which do not have 91 the PCI legacy interfaces. 92 93 If you are building for a PC class system say N here. 94 95 Intel MID platforms are based on an Intel processor and 96 chipset which consume less power than most of the x86 97 derivatives. 98 99# board-specific options below 100source "board/advantech/Kconfig" 101source "board/congatec/Kconfig" 102source "board/coreboot/Kconfig" 103source "board/dfi/Kconfig" 104source "board/efi/Kconfig" 105source "board/emulation/Kconfig" 106source "board/google/Kconfig" 107source "board/intel/Kconfig" 108 109# platform-specific options below 110source "arch/x86/cpu/baytrail/Kconfig" 111source "arch/x86/cpu/braswell/Kconfig" 112source "arch/x86/cpu/broadwell/Kconfig" 113source "arch/x86/cpu/coreboot/Kconfig" 114source "arch/x86/cpu/ivybridge/Kconfig" 115source "arch/x86/cpu/qemu/Kconfig" 116source "arch/x86/cpu/quark/Kconfig" 117source "arch/x86/cpu/queensbay/Kconfig" 118source "arch/x86/cpu/tangier/Kconfig" 119 120# architecture-specific options below 121 122config AHCI 123 default y 124 125config SYS_MALLOC_F_LEN 126 default 0x800 127 128config RAMBASE 129 hex 130 default 0x100000 131 132config XIP_ROM_SIZE 133 hex 134 depends on X86_RESET_VECTOR 135 default ROM_SIZE 136 137config CPU_ADDR_BITS 138 int 139 default 36 140 141config HPET_ADDRESS 142 hex 143 default 0xfed00000 if !HPET_ADDRESS_OVERRIDE 144 145config SMM_TSEG 146 bool 147 default n 148 149config SMM_TSEG_SIZE 150 hex 151 152config X86_RESET_VECTOR 153 bool 154 default n 155 select BINMAN 156 157# The following options control where the 16-bit and 32-bit init lies 158# If SPL is enabled then it normally holds this init code, and U-Boot proper 159# is normally a 64-bit build. 160# 161# The 16-bit init refers to the reset vector and the small amount of code to 162# get the processor into 32-bit mode. It may be in SPL or in U-Boot proper, 163# or missing altogether if U-Boot is started from EFI or coreboot. 164# 165# The 32-bit init refers to processor init, running binary blobs including 166# FSP, setting up interrupts and anything else that needs to be done in 167# 32-bit code. It is normally in the same place as 16-bit init if that is 168# enabled (i.e. they are both in SPL, or both in U-Boot proper). 169config X86_16BIT_INIT 170 bool 171 depends on X86_RESET_VECTOR 172 default y if X86_RESET_VECTOR && !SPL 173 help 174 This is enabled when 16-bit init is in U-Boot proper 175 176config SPL_X86_16BIT_INIT 177 bool 178 depends on X86_RESET_VECTOR 179 default y if X86_RESET_VECTOR && SPL 180 help 181 This is enabled when 16-bit init is in SPL 182 183config X86_32BIT_INIT 184 bool 185 depends on X86_RESET_VECTOR 186 default y if X86_RESET_VECTOR && !SPL 187 help 188 This is enabled when 32-bit init is in U-Boot proper 189 190config SPL_X86_32BIT_INIT 191 bool 192 depends on X86_RESET_VECTOR 193 default y if X86_RESET_VECTOR && SPL 194 help 195 This is enabled when 32-bit init is in SPL 196 197config RESET_SEG_START 198 hex 199 depends on X86_RESET_VECTOR 200 default 0xffff0000 201 202config RESET_SEG_SIZE 203 hex 204 depends on X86_RESET_VECTOR 205 default 0x10000 206 207config RESET_VEC_LOC 208 hex 209 depends on X86_RESET_VECTOR 210 default 0xfffffff0 211 212config SYS_X86_START16 213 hex 214 depends on X86_RESET_VECTOR 215 default 0xfffff800 216 217config X86_LOAD_FROM_32_BIT 218 bool "Boot from a 32-bit program" 219 help 220 Define this to boot U-Boot from a 32-bit program which sets 221 the GDT differently. This can be used to boot directly from 222 any stage of coreboot, for example, bypassing the normal 223 payload-loading feature. 224 225config BOARD_ROMSIZE_KB_512 226 bool 227config BOARD_ROMSIZE_KB_1024 228 bool 229config BOARD_ROMSIZE_KB_2048 230 bool 231config BOARD_ROMSIZE_KB_4096 232 bool 233config BOARD_ROMSIZE_KB_8192 234 bool 235config BOARD_ROMSIZE_KB_16384 236 bool 237 238choice 239 prompt "ROM chip size" 240 depends on X86_RESET_VECTOR 241 default UBOOT_ROMSIZE_KB_512 if BOARD_ROMSIZE_KB_512 242 default UBOOT_ROMSIZE_KB_1024 if BOARD_ROMSIZE_KB_1024 243 default UBOOT_ROMSIZE_KB_2048 if BOARD_ROMSIZE_KB_2048 244 default UBOOT_ROMSIZE_KB_4096 if BOARD_ROMSIZE_KB_4096 245 default UBOOT_ROMSIZE_KB_8192 if BOARD_ROMSIZE_KB_8192 246 default UBOOT_ROMSIZE_KB_16384 if BOARD_ROMSIZE_KB_16384 247 help 248 Select the size of the ROM chip you intend to flash U-Boot on. 249 250 The build system will take care of creating a u-boot.rom file 251 of the matching size. 252 253config UBOOT_ROMSIZE_KB_512 254 bool "512 KB" 255 help 256 Choose this option if you have a 512 KB ROM chip. 257 258config UBOOT_ROMSIZE_KB_1024 259 bool "1024 KB (1 MB)" 260 help 261 Choose this option if you have a 1024 KB (1 MB) ROM chip. 262 263config UBOOT_ROMSIZE_KB_2048 264 bool "2048 KB (2 MB)" 265 help 266 Choose this option if you have a 2048 KB (2 MB) ROM chip. 267 268config UBOOT_ROMSIZE_KB_4096 269 bool "4096 KB (4 MB)" 270 help 271 Choose this option if you have a 4096 KB (4 MB) ROM chip. 272 273config UBOOT_ROMSIZE_KB_8192 274 bool "8192 KB (8 MB)" 275 help 276 Choose this option if you have a 8192 KB (8 MB) ROM chip. 277 278config UBOOT_ROMSIZE_KB_16384 279 bool "16384 KB (16 MB)" 280 help 281 Choose this option if you have a 16384 KB (16 MB) ROM chip. 282 283endchoice 284 285# Map the config names to an integer (KB). 286config UBOOT_ROMSIZE_KB 287 int 288 default 512 if UBOOT_ROMSIZE_KB_512 289 default 1024 if UBOOT_ROMSIZE_KB_1024 290 default 2048 if UBOOT_ROMSIZE_KB_2048 291 default 4096 if UBOOT_ROMSIZE_KB_4096 292 default 8192 if UBOOT_ROMSIZE_KB_8192 293 default 16384 if UBOOT_ROMSIZE_KB_16384 294 295# Map the config names to a hex value (bytes). 296config ROM_SIZE 297 hex 298 default 0x80000 if UBOOT_ROMSIZE_KB_512 299 default 0x100000 if UBOOT_ROMSIZE_KB_1024 300 default 0x200000 if UBOOT_ROMSIZE_KB_2048 301 default 0x400000 if UBOOT_ROMSIZE_KB_4096 302 default 0x800000 if UBOOT_ROMSIZE_KB_8192 303 default 0xc00000 if UBOOT_ROMSIZE_KB_12288 304 default 0x1000000 if UBOOT_ROMSIZE_KB_16384 305 306config HAVE_INTEL_ME 307 bool "Platform requires Intel Management Engine" 308 help 309 Newer higher-end devices have an Intel Management Engine (ME) 310 which is a very large binary blob (typically 1.5MB) which is 311 required for the platform to work. This enforces a particular 312 SPI flash format. You will need to supply the me.bin file in 313 your board directory. 314 315config X86_RAMTEST 316 bool "Perform a simple RAM test after SDRAM initialisation" 317 help 318 If there is something wrong with SDRAM then the platform will 319 often crash within U-Boot or the kernel. This option enables a 320 very simple RAM test that quickly checks whether the SDRAM seems 321 to work correctly. It is not exhaustive but can save time by 322 detecting obvious failures. 323 324config FLASH_DESCRIPTOR_FILE 325 string "Flash descriptor binary filename" 326 depends on HAVE_INTEL_ME 327 default "descriptor.bin" 328 help 329 The filename of the file to use as flash descriptor in the 330 board directory. 331 332config INTEL_ME_FILE 333 string "Intel Management Engine binary filename" 334 depends on HAVE_INTEL_ME 335 default "me.bin" 336 help 337 The filename of the file to use as Intel Management Engine in the 338 board directory. 339 340config HAVE_FSP 341 bool "Add an Firmware Support Package binary" 342 depends on !EFI 343 help 344 Select this option to add an Firmware Support Package binary to 345 the resulting U-Boot image. It is a binary blob which U-Boot uses 346 to set up SDRAM and other chipset specific initialization. 347 348 Note: Without this binary U-Boot will not be able to set up its 349 SDRAM so will not boot. 350 351config FSP_FILE 352 string "Firmware Support Package binary filename" 353 depends on HAVE_FSP 354 default "fsp.bin" 355 help 356 The filename of the file to use as Firmware Support Package binary 357 in the board directory. 358 359config FSP_ADDR 360 hex "Firmware Support Package binary location" 361 depends on HAVE_FSP 362 default 0xfffc0000 363 help 364 FSP is not Position Independent Code (PIC) and the whole FSP has to 365 be rebased if it is placed at a location which is different from the 366 perferred base address specified during the FSP build. Use Intel's 367 Binary Configuration Tool (BCT) to do the rebase. 368 369 The default base address of 0xfffc0000 indicates that the binary must 370 be located at offset 0xc0000 from the beginning of a 1MB flash device. 371 372config FSP_TEMP_RAM_ADDR 373 hex 374 depends on HAVE_FSP 375 default 0x2000000 376 help 377 Stack top address which is used in fsp_init() after DRAM is ready and 378 CAR is disabled. 379 380config FSP_SYS_MALLOC_F_LEN 381 hex 382 depends on HAVE_FSP 383 default 0x100000 384 help 385 Additional size of malloc() pool before relocation. 386 387config FSP_USE_UPD 388 bool 389 depends on HAVE_FSP 390 default y 391 help 392 Most FSPs use UPD data region for some FSP customization. But there 393 are still some FSPs that might not even have UPD. For such FSPs, 394 override this to n in their platform Kconfig files. 395 396config FSP_BROKEN_HOB 397 bool 398 depends on HAVE_FSP 399 help 400 Indicate some buggy FSPs that does not report memory used by FSP 401 itself as reserved in the resource descriptor HOB. Select this to 402 tell U-Boot to do some additional work to ensure U-Boot relocation 403 do not overwrite the important boot service data which is used by 404 FSP, otherwise the subsequent call to fsp_notify() will fail. 405 406config ENABLE_MRC_CACHE 407 bool "Enable MRC cache" 408 depends on !EFI && !SYS_COREBOOT 409 help 410 Enable this feature to cause MRC data to be cached in NV storage 411 to be used for speeding up boot time on future reboots and/or 412 power cycles. 413 414 For platforms that use Intel FSP for the memory initialization, 415 please check FSP output HOB via U-Boot command 'fsp hob' to see 416 if there is FSP_NON_VOLATILE_STORAGE_HOB_GUID (asm/fsp/fsp_hob.h). 417 If such GUID does not exist, MRC cache is not avaiable on such 418 platform (eg: Intel Queensbay), which means selecting this option 419 here does not make any difference. 420 421config HAVE_MRC 422 bool "Add a System Agent binary" 423 depends on !HAVE_FSP 424 help 425 Select this option to add a System Agent binary to 426 the resulting U-Boot image. MRC stands for Memory Reference Code. 427 It is a binary blob which U-Boot uses to set up SDRAM. 428 429 Note: Without this binary U-Boot will not be able to set up its 430 SDRAM so will not boot. 431 432config CACHE_MRC_BIN 433 bool 434 depends on HAVE_MRC 435 default n 436 help 437 Enable caching for the memory reference code binary. This uses an 438 MTRR (memory type range register) to turn on caching for the section 439 of SPI flash that contains the memory reference code. This makes 440 SDRAM init run faster. 441 442config CACHE_MRC_SIZE_KB 443 int 444 depends on HAVE_MRC 445 default 512 446 help 447 Sets the size of the cached area for the memory reference code. 448 This ends at the end of SPI flash (address 0xffffffff) and is 449 measured in KB. Typically this is set to 512, providing for 0.5MB 450 of cached space. 451 452config DCACHE_RAM_BASE 453 hex 454 depends on HAVE_MRC 455 help 456 Sets the base of the data cache area in memory space. This is the 457 start address of the cache-as-RAM (CAR) area and the address varies 458 depending on the CPU. Once CAR is set up, read/write memory becomes 459 available at this address and can be used temporarily until SDRAM 460 is working. 461 462config DCACHE_RAM_SIZE 463 hex 464 depends on HAVE_MRC 465 default 0x40000 466 help 467 Sets the total size of the data cache area in memory space. This 468 sets the size of the cache-as-RAM (CAR) area. Note that much of the 469 CAR space is required by the MRC. The CAR space available to U-Boot 470 is normally at the start and typically extends to 1/4 or 1/2 of the 471 available size. 472 473config DCACHE_RAM_MRC_VAR_SIZE 474 hex 475 depends on HAVE_MRC 476 help 477 This is the amount of CAR (Cache as RAM) reserved for use by the 478 memory reference code. This depends on the implementation of the 479 memory reference code and must be set correctly or the board will 480 not boot. 481 482config HAVE_REFCODE 483 bool "Add a Reference Code binary" 484 help 485 Select this option to add a Reference Code binary to the resulting 486 U-Boot image. This is an Intel binary blob that handles system 487 initialisation, in this case the PCH and System Agent. 488 489 Note: Without this binary (on platforms that need it such as 490 broadwell) U-Boot will be missing some critical setup steps. 491 Various peripherals may fail to work. 492 493config SMP 494 bool "Enable Symmetric Multiprocessing" 495 default n 496 help 497 Enable use of more than one CPU in U-Boot and the Operating System 498 when loaded. Each CPU will be started up and information can be 499 obtained using the 'cpu' command. If this option is disabled, then 500 only one CPU will be enabled regardless of the number of CPUs 501 available. 502 503config MAX_CPUS 504 int "Maximum number of CPUs permitted" 505 depends on SMP 506 default 4 507 help 508 When using multi-CPU chips it is possible for U-Boot to start up 509 more than one CPU. The stack memory used by all of these CPUs is 510 pre-allocated so at present U-Boot wants to know the maximum 511 number of CPUs that may be present. Set this to at least as high 512 as the number of CPUs in your system (it uses about 4KB of RAM for 513 each CPU). 514 515config AP_STACK_SIZE 516 hex 517 depends on SMP 518 default 0x1000 519 help 520 Each additional CPU started by U-Boot requires its own stack. This 521 option sets the stack size used by each CPU and directly affects 522 the memory used by this initialisation process. Typically 4KB is 523 enough space. 524 525config CPU_INTEL_TURBO_NOT_PACKAGE_SCOPED 526 bool 527 help 528 This option indicates that the turbo mode setting is not package 529 scoped. i.e. turbo_enable() needs to be called on not just the 530 bootstrap processor (BSP). 531 532config HAVE_VGA_BIOS 533 bool "Add a VGA BIOS image" 534 help 535 Select this option if you have a VGA BIOS image that you would 536 like to add to your ROM. 537 538config VGA_BIOS_FILE 539 string "VGA BIOS image filename" 540 depends on HAVE_VGA_BIOS 541 default "vga.bin" 542 help 543 The filename of the VGA BIOS image in the board directory. 544 545config VGA_BIOS_ADDR 546 hex "VGA BIOS image location" 547 depends on HAVE_VGA_BIOS 548 default 0xfff90000 549 help 550 The location of VGA BIOS image in the SPI flash. For example, base 551 address of 0xfff90000 indicates that the image will be put at offset 552 0x90000 from the beginning of a 1MB flash device. 553 554config HAVE_VBT 555 bool "Add a Video BIOS Table (VBT) image" 556 depends on HAVE_FSP 557 help 558 Select this option if you have a Video BIOS Table (VBT) image that 559 you would like to add to your ROM. This is normally required if you 560 are using an Intel FSP firmware that is complaint with spec 1.1 or 561 later to initialize the integrated graphics device (IGD). 562 563 Video BIOS Table, or VBT, provides platform and board specific 564 configuration information to the driver that is not discoverable 565 or available through other means. By other means the most used 566 method here is to read EDID table from the attached monitor, over 567 Display Data Channel (DDC) using two pin I2C serial interface. VBT 568 configuration is related to display hardware and is available via 569 the ACPI OpRegion or, on older systems, in the PCI ROM (Option ROM). 570 571config VBT_FILE 572 string "Video BIOS Table (VBT) image filename" 573 depends on HAVE_VBT 574 default "vbt.bin" 575 help 576 The filename of the file to use as Video BIOS Table (VBT) image 577 in the board directory. 578 579config VBT_ADDR 580 hex "Video BIOS Table (VBT) image location" 581 depends on HAVE_VBT 582 default 0xfff90000 583 help 584 The location of Video BIOS Table (VBT) image in the SPI flash. For 585 example, base address of 0xfff90000 indicates that the image will 586 be put at offset 0x90000 from the beginning of a 1MB flash device. 587 588config VIDEO_FSP 589 bool "Enable FSP framebuffer driver support" 590 depends on HAVE_VBT && DM_VIDEO 591 help 592 Turn on this option to enable a framebuffer driver when U-Boot is 593 using Video BIOS Table (VBT) image for FSP firmware to initialize 594 the integrated graphics device. 595 596config ROM_TABLE_ADDR 597 hex 598 default 0xf0000 599 help 600 All x86 tables happen to like the address range from 0x0f0000 601 to 0x100000. We use 0xf0000 as the starting address to store 602 those tables, including PIRQ routing table, Multi-Processor 603 table and ACPI table. 604 605config ROM_TABLE_SIZE 606 hex 607 default 0x10000 608 609menu "System tables" 610 depends on !EFI && !SYS_COREBOOT 611 612config GENERATE_PIRQ_TABLE 613 bool "Generate a PIRQ table" 614 default n 615 help 616 Generate a PIRQ routing table for this board. The PIRQ routing table 617 is generated by U-Boot in the system memory from 0xf0000 to 0xfffff 618 at every 16-byte boundary with a PCI IRQ routing signature ("$PIR"). 619 It specifies the interrupt router information as well how all the PCI 620 devices' interrupt pins are wired to PIRQs. 621 622config GENERATE_SFI_TABLE 623 bool "Generate a SFI (Simple Firmware Interface) table" 624 help 625 The Simple Firmware Interface (SFI) provides a lightweight method 626 for platform firmware to pass information to the operating system 627 via static tables in memory. Kernel SFI support is required to 628 boot on SFI-only platforms. If you have ACPI tables then these are 629 used instead. 630 631 U-Boot writes this table in write_sfi_table() just before booting 632 the OS. 633 634 For more information, see http://simplefirmware.org 635 636config GENERATE_MP_TABLE 637 bool "Generate an MP (Multi-Processor) table" 638 default n 639 help 640 Generate an MP (Multi-Processor) table for this board. The MP table 641 provides a way for the operating system to support for symmetric 642 multiprocessing as well as symmetric I/O interrupt handling with 643 the local APIC and I/O APIC. 644 645config GENERATE_ACPI_TABLE 646 bool "Generate an ACPI (Advanced Configuration and Power Interface) table" 647 default n 648 select QFW if QEMU 649 help 650 The Advanced Configuration and Power Interface (ACPI) specification 651 provides an open standard for device configuration and management 652 by the operating system. It defines platform-independent interfaces 653 for configuration and power management monitoring. 654 655endmenu 656 657config HAVE_ACPI_RESUME 658 bool "Enable ACPI S3 resume" 659 select ENABLE_MRC_CACHE 660 help 661 Select this to enable ACPI S3 resume. S3 is an ACPI-defined sleeping 662 state where all system context is lost except system memory. U-Boot 663 is responsible for restoring the machine state as it was before sleep. 664 It needs restore the memory controller, without overwriting memory 665 which is not marked as reserved. For the peripherals which lose their 666 registers, U-Boot needs to write the original value. When everything 667 is done, U-Boot needs to find out the wakeup vector provided by OSes 668 and jump there. 669 670config S3_VGA_ROM_RUN 671 bool "Re-run VGA option ROMs on S3 resume" 672 depends on HAVE_ACPI_RESUME 673 help 674 Execute VGA option ROMs in U-Boot when resuming from S3. Normally 675 this is needed when graphics console is being used in the kernel. 676 677 Turning it off can reduce some resume time, but be aware that your 678 graphics console won't work without VGA options ROMs. Set it to N 679 if your kernel is only on a serial console. 680 681config STACK_SIZE 682 hex 683 depends on HAVE_ACPI_RESUME 684 default 0x1000 685 help 686 Estimated U-Boot's runtime stack size that needs to be reserved 687 during an ACPI S3 resume. 688 689config MAX_PIRQ_LINKS 690 int 691 default 8 692 help 693 This variable specifies the number of PIRQ interrupt links which are 694 routable. On most older chipsets, this is 4, PIRQA through PIRQD. 695 Some newer chipsets offer more than four links, commonly up to PIRQH. 696 697config IRQ_SLOT_COUNT 698 int 699 default 128 700 help 701 U-Boot can support up to 254 IRQ slot info in the PIRQ routing table 702 which in turns forms a table of exact 4KiB. The default value 128 703 should be enough for most boards. If this does not fit your board, 704 change it according to your needs. 705 706config PCIE_ECAM_BASE 707 hex 708 default 0xe0000000 709 help 710 This is the memory-mapped address of PCI configuration space, which 711 is only available through the Enhanced Configuration Access 712 Mechanism (ECAM) with PCI Express. It can be set up almost 713 anywhere. Before it is set up, it is possible to access PCI 714 configuration space through I/O access, but memory access is more 715 convenient. Using this, PCI can be scanned and configured. This 716 should be set to a region that does not conflict with memory 717 assigned to PCI devices - i.e. the memory and prefetch regions, as 718 passed to pci_set_region(). 719 720config PCIE_ECAM_SIZE 721 hex 722 default 0x10000000 723 help 724 This is the size of memory-mapped address of PCI configuration space, 725 which is only available through the Enhanced Configuration Access 726 Mechanism (ECAM) with PCI Express. Each bus consumes 1 MiB memory, 727 so a default 0x10000000 size covers all of the 256 buses which is the 728 maximum number of PCI buses as defined by the PCI specification. 729 730config I8259_PIC 731 bool 732 default y 733 help 734 Intel 8259 ISA compatible chipset incorporates two 8259 (master and 735 slave) interrupt controllers. Include this to have U-Boot set up 736 the interrupt correctly. 737 738config PINCTRL_ICH6 739 bool 740 help 741 Intel ICH6 compatible chipset pinctrl driver. It needs to work 742 together with the ICH6 compatible gpio driver. 743 744config I8254_TIMER 745 bool 746 default y 747 help 748 Intel 8254 timer contains three counters which have fixed uses. 749 Include this to have U-Boot set up the timer correctly. 750 751config SEABIOS 752 bool "Support booting SeaBIOS" 753 help 754 SeaBIOS is an open source implementation of a 16-bit X86 BIOS. 755 It can run in an emulator or natively on X86 hardware with the use 756 of coreboot/U-Boot. By turning on this option, U-Boot prepares 757 all the configuration tables that are necessary to boot SeaBIOS. 758 759 Check http://www.seabios.org/SeaBIOS for details. 760 761config HIGH_TABLE_SIZE 762 hex "Size of configuration tables which reside in high memory" 763 default 0x10000 764 depends on SEABIOS 765 help 766 SeaBIOS itself resides in E seg and F seg, where U-Boot puts all 767 configuration tables like PIRQ/MP/ACPI. To avoid conflicts, U-Boot 768 puts a copy of configuration tables in high memory region which 769 is reserved on the stack before relocation. The region size is 770 determined by this option. 771 772 Increse it if the default size does not fit the board's needs. 773 This is most likely due to a large ACPI DSDT table is used. 774 775source "arch/x86/lib/efi/Kconfig" 776 777endmenu 778