1 // SPDX-License-Identifier: GPL-2.0-only
2 /*
3 * LCD/Backlight Driver for Sharp Zaurus Handhelds (various models)
4 *
5 * Copyright (c) 2004-2006 Richard Purdie
6 *
7 * Based on Sharp's 2.4 Backlight Driver
8 *
9 * Copyright (c) 2008 Marvell International Ltd.
10 * Converted to SPI device based LCD/Backlight device driver
11 * by Eric Miao <eric.miao@marvell.com>
12 */
13
14 #include <linux/module.h>
15 #include <linux/kernel.h>
16 #include <linux/init.h>
17 #include <linux/delay.h>
18 #include <linux/gpio/consumer.h>
19 #include <linux/fb.h>
20 #include <linux/lcd.h>
21 #include <linux/spi/spi.h>
22 #include <linux/spi/corgi_lcd.h>
23 #include <linux/slab.h>
24 #include <asm/mach/sharpsl_param.h>
25
26 #define POWER_IS_ON(pwr) ((pwr) <= FB_BLANK_NORMAL)
27
28 /* Register Addresses */
29 #define RESCTL_ADRS 0x00
30 #define PHACTRL_ADRS 0x01
31 #define DUTYCTRL_ADRS 0x02
32 #define POWERREG0_ADRS 0x03
33 #define POWERREG1_ADRS 0x04
34 #define GPOR3_ADRS 0x05
35 #define PICTRL_ADRS 0x06
36 #define POLCTRL_ADRS 0x07
37
38 /* Register Bit Definitions */
39 #define RESCTL_QVGA 0x01
40 #define RESCTL_VGA 0x00
41
42 #define POWER1_VW_ON 0x01 /* VW Supply FET ON */
43 #define POWER1_GVSS_ON 0x02 /* GVSS(-8V) Power Supply ON */
44 #define POWER1_VDD_ON 0x04 /* VDD(8V),SVSS(-4V) Power Supply ON */
45
46 #define POWER1_VW_OFF 0x00 /* VW Supply FET OFF */
47 #define POWER1_GVSS_OFF 0x00 /* GVSS(-8V) Power Supply OFF */
48 #define POWER1_VDD_OFF 0x00 /* VDD(8V),SVSS(-4V) Power Supply OFF */
49
50 #define POWER0_COM_DCLK 0x01 /* COM Voltage DC Bias DAC Serial Data Clock */
51 #define POWER0_COM_DOUT 0x02 /* COM Voltage DC Bias DAC Serial Data Out */
52 #define POWER0_DAC_ON 0x04 /* DAC Power Supply ON */
53 #define POWER0_COM_ON 0x08 /* COM Power Supply ON */
54 #define POWER0_VCC5_ON 0x10 /* VCC5 Power Supply ON */
55
56 #define POWER0_DAC_OFF 0x00 /* DAC Power Supply OFF */
57 #define POWER0_COM_OFF 0x00 /* COM Power Supply OFF */
58 #define POWER0_VCC5_OFF 0x00 /* VCC5 Power Supply OFF */
59
60 #define PICTRL_INIT_STATE 0x01
61 #define PICTRL_INIOFF 0x02
62 #define PICTRL_POWER_DOWN 0x04
63 #define PICTRL_COM_SIGNAL_OFF 0x08
64 #define PICTRL_DAC_SIGNAL_OFF 0x10
65
66 #define POLCTRL_SYNC_POL_FALL 0x01
67 #define POLCTRL_EN_POL_FALL 0x02
68 #define POLCTRL_DATA_POL_FALL 0x04
69 #define POLCTRL_SYNC_ACT_H 0x08
70 #define POLCTRL_EN_ACT_L 0x10
71
72 #define POLCTRL_SYNC_POL_RISE 0x00
73 #define POLCTRL_EN_POL_RISE 0x00
74 #define POLCTRL_DATA_POL_RISE 0x00
75 #define POLCTRL_SYNC_ACT_L 0x00
76 #define POLCTRL_EN_ACT_H 0x00
77
78 #define PHACTRL_PHASE_MANUAL 0x01
79 #define DEFAULT_PHAD_QVGA (9)
80 #define DEFAULT_COMADJ (125)
81
82 struct corgi_lcd {
83 struct spi_device *spi_dev;
84 struct lcd_device *lcd_dev;
85 struct backlight_device *bl_dev;
86
87 int limit_mask;
88 int intensity;
89 int power;
90 int mode;
91 char buf[2];
92
93 struct gpio_desc *backlight_on;
94 struct gpio_desc *backlight_cont;
95
96 void (*kick_battery)(void);
97 };
98
99 static int corgi_ssp_lcdtg_send(struct corgi_lcd *lcd, int reg, uint8_t val);
100
101 static struct corgi_lcd *the_corgi_lcd;
102 static unsigned long corgibl_flags;
103 #define CORGIBL_SUSPENDED 0x01
104 #define CORGIBL_BATTLOW 0x02
105
106 /*
107 * This is only a pseudo I2C interface. We can't use the standard kernel
108 * routines as the interface is write only. We just assume the data is acked...
109 */
lcdtg_ssp_i2c_send(struct corgi_lcd * lcd,uint8_t data)110 static void lcdtg_ssp_i2c_send(struct corgi_lcd *lcd, uint8_t data)
111 {
112 corgi_ssp_lcdtg_send(lcd, POWERREG0_ADRS, data);
113 udelay(10);
114 }
115
lcdtg_i2c_send_bit(struct corgi_lcd * lcd,uint8_t data)116 static void lcdtg_i2c_send_bit(struct corgi_lcd *lcd, uint8_t data)
117 {
118 lcdtg_ssp_i2c_send(lcd, data);
119 lcdtg_ssp_i2c_send(lcd, data | POWER0_COM_DCLK);
120 lcdtg_ssp_i2c_send(lcd, data);
121 }
122
lcdtg_i2c_send_start(struct corgi_lcd * lcd,uint8_t base)123 static void lcdtg_i2c_send_start(struct corgi_lcd *lcd, uint8_t base)
124 {
125 lcdtg_ssp_i2c_send(lcd, base | POWER0_COM_DCLK | POWER0_COM_DOUT);
126 lcdtg_ssp_i2c_send(lcd, base | POWER0_COM_DCLK);
127 lcdtg_ssp_i2c_send(lcd, base);
128 }
129
lcdtg_i2c_send_stop(struct corgi_lcd * lcd,uint8_t base)130 static void lcdtg_i2c_send_stop(struct corgi_lcd *lcd, uint8_t base)
131 {
132 lcdtg_ssp_i2c_send(lcd, base);
133 lcdtg_ssp_i2c_send(lcd, base | POWER0_COM_DCLK);
134 lcdtg_ssp_i2c_send(lcd, base | POWER0_COM_DCLK | POWER0_COM_DOUT);
135 }
136
lcdtg_i2c_send_byte(struct corgi_lcd * lcd,uint8_t base,uint8_t data)137 static void lcdtg_i2c_send_byte(struct corgi_lcd *lcd,
138 uint8_t base, uint8_t data)
139 {
140 int i;
141
142 for (i = 0; i < 8; i++) {
143 if (data & 0x80)
144 lcdtg_i2c_send_bit(lcd, base | POWER0_COM_DOUT);
145 else
146 lcdtg_i2c_send_bit(lcd, base);
147 data <<= 1;
148 }
149 }
150
lcdtg_i2c_wait_ack(struct corgi_lcd * lcd,uint8_t base)151 static void lcdtg_i2c_wait_ack(struct corgi_lcd *lcd, uint8_t base)
152 {
153 lcdtg_i2c_send_bit(lcd, base);
154 }
155
lcdtg_set_common_voltage(struct corgi_lcd * lcd,uint8_t base_data,uint8_t data)156 static void lcdtg_set_common_voltage(struct corgi_lcd *lcd,
157 uint8_t base_data, uint8_t data)
158 {
159 /* Set Common Voltage to M62332FP via I2C */
160 lcdtg_i2c_send_start(lcd, base_data);
161 lcdtg_i2c_send_byte(lcd, base_data, 0x9c);
162 lcdtg_i2c_wait_ack(lcd, base_data);
163 lcdtg_i2c_send_byte(lcd, base_data, 0x00);
164 lcdtg_i2c_wait_ack(lcd, base_data);
165 lcdtg_i2c_send_byte(lcd, base_data, data);
166 lcdtg_i2c_wait_ack(lcd, base_data);
167 lcdtg_i2c_send_stop(lcd, base_data);
168 }
169
corgi_ssp_lcdtg_send(struct corgi_lcd * lcd,int adrs,uint8_t data)170 static int corgi_ssp_lcdtg_send(struct corgi_lcd *lcd, int adrs, uint8_t data)
171 {
172 struct spi_message msg;
173 struct spi_transfer xfer = {
174 .len = 1,
175 .cs_change = 0,
176 .tx_buf = lcd->buf,
177 };
178
179 lcd->buf[0] = ((adrs & 0x07) << 5) | (data & 0x1f);
180 spi_message_init(&msg);
181 spi_message_add_tail(&xfer, &msg);
182
183 return spi_sync(lcd->spi_dev, &msg);
184 }
185
186 /* Set Phase Adjust */
lcdtg_set_phadadj(struct corgi_lcd * lcd,int mode)187 static void lcdtg_set_phadadj(struct corgi_lcd *lcd, int mode)
188 {
189 int adj;
190
191 switch (mode) {
192 case CORGI_LCD_MODE_VGA:
193 /* Setting for VGA */
194 adj = sharpsl_param.phadadj;
195 adj = (adj < 0) ? PHACTRL_PHASE_MANUAL :
196 PHACTRL_PHASE_MANUAL | ((adj & 0xf) << 1);
197 break;
198 case CORGI_LCD_MODE_QVGA:
199 default:
200 /* Setting for QVGA */
201 adj = (DEFAULT_PHAD_QVGA << 1) | PHACTRL_PHASE_MANUAL;
202 break;
203 }
204
205 corgi_ssp_lcdtg_send(lcd, PHACTRL_ADRS, adj);
206 }
207
corgi_lcd_power_on(struct corgi_lcd * lcd)208 static void corgi_lcd_power_on(struct corgi_lcd *lcd)
209 {
210 int comadj;
211
212 /* Initialize Internal Logic & Port */
213 corgi_ssp_lcdtg_send(lcd, PICTRL_ADRS,
214 PICTRL_POWER_DOWN | PICTRL_INIOFF |
215 PICTRL_INIT_STATE | PICTRL_COM_SIGNAL_OFF |
216 PICTRL_DAC_SIGNAL_OFF);
217
218 corgi_ssp_lcdtg_send(lcd, POWERREG0_ADRS,
219 POWER0_COM_DCLK | POWER0_COM_DOUT | POWER0_DAC_OFF |
220 POWER0_COM_OFF | POWER0_VCC5_OFF);
221
222 corgi_ssp_lcdtg_send(lcd, POWERREG1_ADRS,
223 POWER1_VW_OFF | POWER1_GVSS_OFF | POWER1_VDD_OFF);
224
225 /* VDD(+8V), SVSS(-4V) ON */
226 corgi_ssp_lcdtg_send(lcd, POWERREG1_ADRS,
227 POWER1_VW_OFF | POWER1_GVSS_OFF | POWER1_VDD_ON);
228 mdelay(3);
229
230 /* DAC ON */
231 corgi_ssp_lcdtg_send(lcd, POWERREG0_ADRS,
232 POWER0_COM_DCLK | POWER0_COM_DOUT | POWER0_DAC_ON |
233 POWER0_COM_OFF | POWER0_VCC5_OFF);
234
235 /* INIB = H, INI = L */
236 /* PICTL[0] = H , PICTL[1] = PICTL[2] = PICTL[4] = L */
237 corgi_ssp_lcdtg_send(lcd, PICTRL_ADRS,
238 PICTRL_INIT_STATE | PICTRL_COM_SIGNAL_OFF);
239
240 /* Set Common Voltage */
241 comadj = sharpsl_param.comadj;
242 if (comadj < 0)
243 comadj = DEFAULT_COMADJ;
244
245 lcdtg_set_common_voltage(lcd, POWER0_DAC_ON | POWER0_COM_OFF |
246 POWER0_VCC5_OFF, comadj);
247
248 /* VCC5 ON, DAC ON */
249 corgi_ssp_lcdtg_send(lcd, POWERREG0_ADRS,
250 POWER0_COM_DCLK | POWER0_COM_DOUT | POWER0_DAC_ON |
251 POWER0_COM_OFF | POWER0_VCC5_ON);
252
253 /* GVSS(-8V) ON, VDD ON */
254 corgi_ssp_lcdtg_send(lcd, POWERREG1_ADRS,
255 POWER1_VW_OFF | POWER1_GVSS_ON | POWER1_VDD_ON);
256 mdelay(2);
257
258 /* COM SIGNAL ON (PICTL[3] = L) */
259 corgi_ssp_lcdtg_send(lcd, PICTRL_ADRS, PICTRL_INIT_STATE);
260
261 /* COM ON, DAC ON, VCC5_ON */
262 corgi_ssp_lcdtg_send(lcd, POWERREG0_ADRS,
263 POWER0_COM_DCLK | POWER0_COM_DOUT | POWER0_DAC_ON |
264 POWER0_COM_ON | POWER0_VCC5_ON);
265
266 /* VW ON, GVSS ON, VDD ON */
267 corgi_ssp_lcdtg_send(lcd, POWERREG1_ADRS,
268 POWER1_VW_ON | POWER1_GVSS_ON | POWER1_VDD_ON);
269
270 /* Signals output enable */
271 corgi_ssp_lcdtg_send(lcd, PICTRL_ADRS, 0);
272
273 /* Set Phase Adjust */
274 lcdtg_set_phadadj(lcd, lcd->mode);
275
276 /* Initialize for Input Signals from ATI */
277 corgi_ssp_lcdtg_send(lcd, POLCTRL_ADRS,
278 POLCTRL_SYNC_POL_RISE | POLCTRL_EN_POL_RISE |
279 POLCTRL_DATA_POL_RISE | POLCTRL_SYNC_ACT_L |
280 POLCTRL_EN_ACT_H);
281 udelay(1000);
282
283 switch (lcd->mode) {
284 case CORGI_LCD_MODE_VGA:
285 corgi_ssp_lcdtg_send(lcd, RESCTL_ADRS, RESCTL_VGA);
286 break;
287 case CORGI_LCD_MODE_QVGA:
288 default:
289 corgi_ssp_lcdtg_send(lcd, RESCTL_ADRS, RESCTL_QVGA);
290 break;
291 }
292 }
293
corgi_lcd_power_off(struct corgi_lcd * lcd)294 static void corgi_lcd_power_off(struct corgi_lcd *lcd)
295 {
296 /* 60Hz x 2 frame = 16.7msec x 2 = 33.4 msec */
297 msleep(34);
298
299 /* (1)VW OFF */
300 corgi_ssp_lcdtg_send(lcd, POWERREG1_ADRS,
301 POWER1_VW_OFF | POWER1_GVSS_ON | POWER1_VDD_ON);
302
303 /* (2)COM OFF */
304 corgi_ssp_lcdtg_send(lcd, PICTRL_ADRS, PICTRL_COM_SIGNAL_OFF);
305 corgi_ssp_lcdtg_send(lcd, POWERREG0_ADRS,
306 POWER0_DAC_ON | POWER0_COM_OFF | POWER0_VCC5_ON);
307
308 /* (3)Set Common Voltage Bias 0V */
309 lcdtg_set_common_voltage(lcd, POWER0_DAC_ON | POWER0_COM_OFF |
310 POWER0_VCC5_ON, 0);
311
312 /* (4)GVSS OFF */
313 corgi_ssp_lcdtg_send(lcd, POWERREG1_ADRS,
314 POWER1_VW_OFF | POWER1_GVSS_OFF | POWER1_VDD_ON);
315
316 /* (5)VCC5 OFF */
317 corgi_ssp_lcdtg_send(lcd, POWERREG0_ADRS,
318 POWER0_DAC_ON | POWER0_COM_OFF | POWER0_VCC5_OFF);
319
320 /* (6)Set PDWN, INIOFF, DACOFF */
321 corgi_ssp_lcdtg_send(lcd, PICTRL_ADRS,
322 PICTRL_INIOFF | PICTRL_DAC_SIGNAL_OFF |
323 PICTRL_POWER_DOWN | PICTRL_COM_SIGNAL_OFF);
324
325 /* (7)DAC OFF */
326 corgi_ssp_lcdtg_send(lcd, POWERREG0_ADRS,
327 POWER0_DAC_OFF | POWER0_COM_OFF | POWER0_VCC5_OFF);
328
329 /* (8)VDD OFF */
330 corgi_ssp_lcdtg_send(lcd, POWERREG1_ADRS,
331 POWER1_VW_OFF | POWER1_GVSS_OFF | POWER1_VDD_OFF);
332 }
333
corgi_lcd_set_mode(struct lcd_device * ld,struct fb_videomode * m)334 static int corgi_lcd_set_mode(struct lcd_device *ld, struct fb_videomode *m)
335 {
336 struct corgi_lcd *lcd = lcd_get_data(ld);
337 int mode = CORGI_LCD_MODE_QVGA;
338
339 if (m->xres == 640 || m->xres == 480)
340 mode = CORGI_LCD_MODE_VGA;
341
342 if (lcd->mode == mode)
343 return 0;
344
345 lcdtg_set_phadadj(lcd, mode);
346
347 switch (mode) {
348 case CORGI_LCD_MODE_VGA:
349 corgi_ssp_lcdtg_send(lcd, RESCTL_ADRS, RESCTL_VGA);
350 break;
351 case CORGI_LCD_MODE_QVGA:
352 default:
353 corgi_ssp_lcdtg_send(lcd, RESCTL_ADRS, RESCTL_QVGA);
354 break;
355 }
356
357 lcd->mode = mode;
358 return 0;
359 }
360
corgi_lcd_set_power(struct lcd_device * ld,int power)361 static int corgi_lcd_set_power(struct lcd_device *ld, int power)
362 {
363 struct corgi_lcd *lcd = lcd_get_data(ld);
364
365 if (POWER_IS_ON(power) && !POWER_IS_ON(lcd->power))
366 corgi_lcd_power_on(lcd);
367
368 if (!POWER_IS_ON(power) && POWER_IS_ON(lcd->power))
369 corgi_lcd_power_off(lcd);
370
371 lcd->power = power;
372 return 0;
373 }
374
corgi_lcd_get_power(struct lcd_device * ld)375 static int corgi_lcd_get_power(struct lcd_device *ld)
376 {
377 struct corgi_lcd *lcd = lcd_get_data(ld);
378
379 return lcd->power;
380 }
381
382 static struct lcd_ops corgi_lcd_ops = {
383 .get_power = corgi_lcd_get_power,
384 .set_power = corgi_lcd_set_power,
385 .set_mode = corgi_lcd_set_mode,
386 };
387
corgi_bl_get_intensity(struct backlight_device * bd)388 static int corgi_bl_get_intensity(struct backlight_device *bd)
389 {
390 struct corgi_lcd *lcd = bl_get_data(bd);
391
392 return lcd->intensity;
393 }
394
corgi_bl_set_intensity(struct corgi_lcd * lcd,int intensity)395 static int corgi_bl_set_intensity(struct corgi_lcd *lcd, int intensity)
396 {
397 int cont;
398
399 if (intensity > 0x10)
400 intensity += 0x10;
401
402 corgi_ssp_lcdtg_send(lcd, DUTYCTRL_ADRS, intensity);
403
404 /* Bit 5 via GPIO_BACKLIGHT_CONT */
405 cont = !!(intensity & 0x20);
406
407 if (lcd->backlight_cont)
408 gpiod_set_value_cansleep(lcd->backlight_cont, cont);
409
410 if (lcd->backlight_on)
411 gpiod_set_value_cansleep(lcd->backlight_on, intensity);
412
413 if (lcd->kick_battery)
414 lcd->kick_battery();
415
416 lcd->intensity = intensity;
417 return 0;
418 }
419
corgi_bl_update_status(struct backlight_device * bd)420 static int corgi_bl_update_status(struct backlight_device *bd)
421 {
422 struct corgi_lcd *lcd = bl_get_data(bd);
423 int intensity = backlight_get_brightness(bd);
424
425 if (corgibl_flags & CORGIBL_SUSPENDED)
426 intensity = 0;
427
428 if ((corgibl_flags & CORGIBL_BATTLOW) && intensity > lcd->limit_mask)
429 intensity = lcd->limit_mask;
430
431 return corgi_bl_set_intensity(lcd, intensity);
432 }
433
corgi_lcd_limit_intensity(int limit)434 void corgi_lcd_limit_intensity(int limit)
435 {
436 if (limit)
437 corgibl_flags |= CORGIBL_BATTLOW;
438 else
439 corgibl_flags &= ~CORGIBL_BATTLOW;
440
441 backlight_update_status(the_corgi_lcd->bl_dev);
442 }
443 EXPORT_SYMBOL(corgi_lcd_limit_intensity);
444
445 static const struct backlight_ops corgi_bl_ops = {
446 .get_brightness = corgi_bl_get_intensity,
447 .update_status = corgi_bl_update_status,
448 };
449
450 #ifdef CONFIG_PM_SLEEP
corgi_lcd_suspend(struct device * dev)451 static int corgi_lcd_suspend(struct device *dev)
452 {
453 struct corgi_lcd *lcd = dev_get_drvdata(dev);
454
455 corgibl_flags |= CORGIBL_SUSPENDED;
456 corgi_bl_set_intensity(lcd, 0);
457 corgi_lcd_set_power(lcd->lcd_dev, FB_BLANK_POWERDOWN);
458 return 0;
459 }
460
corgi_lcd_resume(struct device * dev)461 static int corgi_lcd_resume(struct device *dev)
462 {
463 struct corgi_lcd *lcd = dev_get_drvdata(dev);
464
465 corgibl_flags &= ~CORGIBL_SUSPENDED;
466 corgi_lcd_set_power(lcd->lcd_dev, FB_BLANK_UNBLANK);
467 backlight_update_status(lcd->bl_dev);
468 return 0;
469 }
470 #endif
471
472 static SIMPLE_DEV_PM_OPS(corgi_lcd_pm_ops, corgi_lcd_suspend, corgi_lcd_resume);
473
setup_gpio_backlight(struct corgi_lcd * lcd,struct corgi_lcd_platform_data * pdata)474 static int setup_gpio_backlight(struct corgi_lcd *lcd,
475 struct corgi_lcd_platform_data *pdata)
476 {
477 struct spi_device *spi = lcd->spi_dev;
478
479 lcd->backlight_on = devm_gpiod_get_optional(&spi->dev,
480 "BL_ON", GPIOD_OUT_LOW);
481 if (IS_ERR(lcd->backlight_on))
482 return PTR_ERR(lcd->backlight_on);
483
484 lcd->backlight_cont = devm_gpiod_get_optional(&spi->dev, "BL_CONT",
485 GPIOD_OUT_LOW);
486 if (IS_ERR(lcd->backlight_cont))
487 return PTR_ERR(lcd->backlight_cont);
488
489 return 0;
490 }
491
corgi_lcd_probe(struct spi_device * spi)492 static int corgi_lcd_probe(struct spi_device *spi)
493 {
494 struct backlight_properties props;
495 struct corgi_lcd_platform_data *pdata = dev_get_platdata(&spi->dev);
496 struct corgi_lcd *lcd;
497 int ret = 0;
498
499 if (pdata == NULL) {
500 dev_err(&spi->dev, "platform data not available\n");
501 return -EINVAL;
502 }
503
504 lcd = devm_kzalloc(&spi->dev, sizeof(struct corgi_lcd), GFP_KERNEL);
505 if (!lcd)
506 return -ENOMEM;
507
508 lcd->spi_dev = spi;
509
510 lcd->lcd_dev = devm_lcd_device_register(&spi->dev, "corgi_lcd",
511 &spi->dev, lcd, &corgi_lcd_ops);
512 if (IS_ERR(lcd->lcd_dev))
513 return PTR_ERR(lcd->lcd_dev);
514
515 lcd->power = FB_BLANK_POWERDOWN;
516 lcd->mode = (pdata) ? pdata->init_mode : CORGI_LCD_MODE_VGA;
517
518 memset(&props, 0, sizeof(struct backlight_properties));
519 props.type = BACKLIGHT_RAW;
520 props.max_brightness = pdata->max_intensity;
521 lcd->bl_dev = devm_backlight_device_register(&spi->dev, "corgi_bl",
522 &spi->dev, lcd, &corgi_bl_ops,
523 &props);
524 if (IS_ERR(lcd->bl_dev))
525 return PTR_ERR(lcd->bl_dev);
526
527 lcd->bl_dev->props.brightness = pdata->default_intensity;
528 lcd->bl_dev->props.power = FB_BLANK_UNBLANK;
529
530 ret = setup_gpio_backlight(lcd, pdata);
531 if (ret)
532 return ret;
533
534 lcd->kick_battery = pdata->kick_battery;
535
536 spi_set_drvdata(spi, lcd);
537 corgi_lcd_set_power(lcd->lcd_dev, FB_BLANK_UNBLANK);
538 backlight_update_status(lcd->bl_dev);
539
540 lcd->limit_mask = pdata->limit_mask;
541 the_corgi_lcd = lcd;
542 return 0;
543 }
544
corgi_lcd_remove(struct spi_device * spi)545 static void corgi_lcd_remove(struct spi_device *spi)
546 {
547 struct corgi_lcd *lcd = spi_get_drvdata(spi);
548
549 lcd->bl_dev->props.power = FB_BLANK_UNBLANK;
550 lcd->bl_dev->props.brightness = 0;
551 backlight_update_status(lcd->bl_dev);
552 corgi_lcd_set_power(lcd->lcd_dev, FB_BLANK_POWERDOWN);
553 }
554
555 static struct spi_driver corgi_lcd_driver = {
556 .driver = {
557 .name = "corgi-lcd",
558 .pm = &corgi_lcd_pm_ops,
559 },
560 .probe = corgi_lcd_probe,
561 .remove = corgi_lcd_remove,
562 };
563
564 module_spi_driver(corgi_lcd_driver);
565
566 MODULE_DESCRIPTION("LCD and backlight driver for SHARP C7x0/Cxx00");
567 MODULE_AUTHOR("Eric Miao <eric.miao@marvell.com>");
568 MODULE_LICENSE("GPL");
569 MODULE_ALIAS("spi:corgi-lcd");
570